| Age | Commit message (Collapse) | Author |
|---|
|
With CONFIG_MODVERSIONS=y the R_RISCV_32 relocation is used by the
__kcrctab section.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
The EXPORT_SYMBOL(_mcount) for RISC-V ended up inside a
CONFIG_DYNAMIC_FTRACE ifdef. If you enable modules without enabling
CONFIG_DYNAMIC_FTRACE then you'll get a build error without this patch
because the modules won't be able to find _mcount.
The new behavior is to export _mcount whenever CONFIG_FUNCTION_TRACER is
defined. This matches what every other architecture is doing.
Signed-off-by: Alan Kao <alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Zong Li <zong@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
RISC-V uses the macro __riscv_xlen, predefined by GCC, to
make the distinction between 32 or 64 bit code.
However, sparse doesn't know anything about this macro
which lead to wrong warnings and failures.
Fix this by adding a define of __riscv_xlen to CHECKFLAGS
and add one for __riscv too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
This patch addresses two issues. First it adds the correct bit definitions
for the SECTXSTAT and SECRXSTAT registers. Then it makes use of those
definitions to test for if IPsec has been disabled on the part and if so we
do not enable it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: Andre Tomt <andre@tomt.net>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes two issues. First we add an early test for the Tx and Rx
security block ready bits. By doing this we can avoid the need for waits or
loopback in the event that the security block is already flushed out.
Secondly we fix the boolean logic that was testing for the Tx OR Rx ready
bits being set and change it so that we only exit if the Tx AND Rx ready
bits are both set.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch moves the IPsec init function in ixgbe_sw_init. This way it is a
bit more consistent with the placement of similar initialization functions
and is placed before the reset_hw call which should allow us to clean up
any link issues that may be introduced by the fact that we force the link
up if somehow the device had IPsec still enabled before the driver was
loaded.
In addition to the function move it is necessary to change the assignment
of netdev->features. The easiest way to do this is to just test for the
existence of adapter->ipsec and if it is present we set the feature bits.
Fixes: 49a94d74d948 ("ixgbe: add ipsec engine start and stop routines")
Reported-by: Andre Tomt <andre@tomt.net>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is no point in adding code if CONFIG_XFRM is defined that we won't
use unless CONFIG_XFRM_OFFLOAD is defined. So instead of leaving this code
floating around I am replacing the ifdef with what I believe is the correct
one so that we only include the code and variables if they will actually be
used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There's no need to retain the fs/autofs4 directory for backward
compatibility.
Adding an AUTOFS4_FS fragment to the autofs Kconfig and a module alias
for autofs4 is sufficient for almost all cases. Not keeping fs/autofs4
remnants will prevent "insmod <path>/autofs4/autofs4.ko" from working
but this shouldn't be used in automation scripts rather than
modprobe(8).
There were some comments about things to look out for with the module
rename in the fs/autofs4/Kconfig that is removed by this patch, see the
commit patch if you are interested.
One potential problem with this change is that when the
fs/autofs/Kconfig fragment for AUTOFS4_FS is removed any AUTOFS4_FS
entries will be removed from the kernel config, resulting in no autofs
file system being built if there is no AUTOFS_FS entry also.
This would have also happened if the fs/autofs4 remnants had remained
and is most likely to be a problem with automated builds.
Please check your build configurations before the removal which will
occur after the next couple of kernel releases.
Acked-by: Ian Kent <raven@themaw.net>
[ With edits and commit message from Ian Kent ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we were enabling macvlan interfaces we weren't correctly configuring
things until ixgbe_setup_tc was called a second time either by tweaking the
number of queues or increasing the macvlan count past 15.
The issue came down to the fact that num_rx_pools is not populated until
after the queues and interrupts are reinitialized.
Instead of trying to set it sooner we can just move the call to setup at
least 1 traffic class to the SR-IOV/VMDq setup function so that we just set
it for this one case. We already had a spot that was configuring the queues
for TC 0 in the code here anyway so it makes sense to also set the number
of TCs here as well.
Fixes: 49cfbeb7a95c ("ixgbe: Fix handling of macvlan Tx offload")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Core Frameworks
- Provide helpers to enable/disable backlight
- Provide standard and devres versions OF find helpers
New Drivers:
- Add support for the Zodiac Inflight Innovations RAVE Supervisory
Processor
New Functionality:
- Allow pwm-on/pwm-off delay to be specified via DT
Bug Fixes:
- Fix ordering of the power {en,dis}able and PWM {en,dis}able
signals
- Fix Device Tree node look-up"
* tag 'backlight-next-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: as3711_bl: Fix Device Tree node leaks
backlight: tps65217_bl: Fix Device Tree node lookup
backlight: max8925_bl: Fix Device Tree node lookup
backlight: as3711_bl: Fix Device Tree node lookup
MAINTAINERS: Add dri-devel for backlight subsystem patches
backlight: Nuke BL_CORE_DRIVER1
staging: fbtft: Stop using BL_CORE_DRIVER1
backlight: pandora: Stop using BL_CORE_DRIVER1
backlight: generic-bl: Remove DRIVER1 state
backlight: Nuke unused backlight.props.state states
backlight: otm3225a: Add support for ORISE OTM3225A LCD SoC
backlight: pwm_bl: Don't use GPIOF_* with gpiod_get_direction
pwm-backlight: Add support for PWM delays proprieties.
dt-bindings: pwm-backlight: Add PWM delay proprieties.
pwm-backlight: Enable/disable the PWM before/after LCD enable toggle.
dt-bindings: backlight: Add binding for RAVE SP backlight driver
backlight: Add RAVE SP backlight driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- Add support for AXP813 ADC to AXP20x
- Add support for PM8005, PM8998 and PMI8998
New Functionality:
- Add support for Battery Power Supply to AXP813
- Add support for SYSCON to SPARD SC27XX SPI
- Add support for RTC to ChromeOS Embedded-Controller
Fix-ups:
- Remove unused code; exynos{4,5}-pmu, cros_ec, cros_ec_acpi_gpe
- Remove duplicate error messages (-ENOMEM, etc); htc-i2cpld,
janz-cmodio, max8997, rc5t583, sm501, smsc-ece1099, abx500-core,
si476x-i2c, ti_am335x_tscadc, tps65090, tps6586x, tps65910,
tps80031, twl6030-irq, viperboard
- Succinctly use ptr to struct in sizeof(); rc5t583, abx500-core,
sm501, smsc-ece1099
- Simplify syntax for NULL ptr checking; abx500-core, sm501
- No not unnecessarily initialise variables; tps65910, tps65910
- Reorganise and simplify driver data; omap-usb-tll
- Move to SPDX license statement; tps68470
- Probe ADCs via DT; axp20x
- Use new GPIOD API; arizona-core
- Constify things; axp20x
- Reduce code-size (use MACROS, etc); axp20x, omap-usb-host
- Add DT support/docs; motorola-cpcap
- Remove VLAs; rave-sp
- Use devm_* managed resources; cros_ec
- Interrogate HW for firmware version; rave-sp
- Provide ACPI support for ChromeOS Embedded-Controller
Bug Fixes:
- Reorder ordered (enum) device list; tps65218
- Only accept valid data from the offset; rave-sp
- Refrain from copying junk from failed SPI read; cros_ec_dev
- Fix potential memory leaks; pcf50633-core
- Fix clock initialisation; twl-core
- Fix build-issue; tps65911
- Fix off-by-one error; tps65911
- Fix code ordering issues; intel-lpss
- Fix COMPILE_TEST related issues; pwm-stm32
- Fix broken MMC card detection; asic3
- Fix clocking related issues; intel-lpss-pci"
* tag 'mfd-next-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: cros_ec: Remove unused __remove function
mfd: wm97xx-core: Platform data can be NULL
mfd: cros_ec_dev: Don't advertise junk features on failure
mfd: cros_ec: Use devm_kzalloc for private data
mfd: intel-lpss: Fix Intel Cannon Lake LPSS I2C input clock
mfd: asic3: Fix broken MMC card detection
mfd: timberdale: Fix spelling mistake "Uknown" -> "Unknown"
mfd: omap-usb-host: Use match_string() helper
mfd: stm32-timers: Fix pwm-stm32 linker issue with COMPILE_TEST
pwm: stm32: Initialize raw local variables
mfd: arizona: Update DT doc to support more standard Reset binding
dt-bindings: mfd: Add bindings for DA9063L
mfd: intel-lpss: Correct names of RESETS register bits
mfd: qcom-spmi-pmic: Add support for pm8005, pm8998 and pmi8998
mfd: intel-lpss: Program REMAP register in PIO mode
mfd: cros_ec_i2c: Moving the system sleep pm ops to late
mfd: cros_ec_i2c: Add ACPI module device table
mfd: cros_ec_dev: Register shutdown function for debugfs
mfd: cros_ec_dev: Register cros-ec-rtc driver as a subdevice
mfd: cros_ec: Don't try to grab log when suspended
...
|
|
Free smart-log buffer allocated in the function after use.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
After dma mapping the sgl, we map the sgl to nvme sgl descriptor. In case
of failure during the last mapping we never dma unmap the sgl.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Adding a tracepoint to trace bio remapping for native nvme multipath.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When using nvme-pci driver the nvmf_ctrl_options is NULL.
There is no need to check for discovery_nqn flag at non-fabrics controller.
Fixes: 181303d0 ("nvme-fabrics: allow duplicate connections to the discovery controller")
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Pull drm msm updates and misc fixes from Dave Airlie:
"I looked at Rob's msm tree, he kept it small due to being late, and it
was in -next for a while before he was ill, so I think it should be
fine.
Otherwise this contains a set of i915 fixes and a v3d build fix, and
vc4 leak fix"
* tag 'drm-next-2018-06-11' of git://anongit.freedesktop.org/drm/drm: (31 commits)
drm/i915/icl: Don't update enabled dbuf slices struct until updated in hw
drm/i915/icl: fix icl_unmap/map_plls_to_ports
drm/i915: Remove bogus NV12 PLANE_COLOR_CTL setup
drm/msm: Fix NULL deref on bind/probe deferral
drm/msm: Switch to atomic_helper_commit()
drm/msm: Remove msm_commit/worker, use atomic helper commit
drm/msm: Issue queued events when disabling crtc
drm/msm: Move implicit sync handling to prepare_fb
drm/msm: Refactor complete_commit() to look more the helpers
drm/msm: Don't subclass drm_atomic_state anymore
drm/msm/mdp5: Use the new private_obj state
drm/msm/mdp5: Add global state as a private atomic object
drm/msm: use correct aspace pointer in msm_gem_put_iova()
drm/msm: remove unbalanced mutex unlock
drm/msm: don't deref error pointer in the msm_fbdev_create error path
drm/msm/dsi: use correct enum in dsi_get_cmd_fmt
drm/msm: Fix possible null dereference on failure of get_pages()
drm/msm: Add modifier to mdp_get_format arguments
drm/msm: Mark the crtc->state->event consumed
drm/msm/dsi: implement auto PHY timing calculator for 10nm PHY
...
|
|
It is not allowed to reinit q->tag_set_list list entry while RCU grace
period has not completed yet, otherwise the following soft lockup in
blk_mq_sched_restart() happens:
[ 1064.252652] watchdog: BUG: soft lockup - CPU#12 stuck for 23s! [fio:9270]
[ 1064.254445] task: ffff99b912e8b900 task.stack: ffffa6d54c758000
[ 1064.254613] RIP: 0010:blk_mq_sched_restart+0x96/0x150
[ 1064.256510] Call Trace:
[ 1064.256664] <IRQ>
[ 1064.256824] blk_mq_free_request+0xea/0x100
[ 1064.256987] msg_io_conf+0x59/0xd0 [ibnbd_client]
[ 1064.257175] complete_rdma_req+0xf2/0x230 [ibtrs_client]
[ 1064.257340] ? ibtrs_post_recv_empty+0x4d/0x70 [ibtrs_core]
[ 1064.257502] ibtrs_clt_rdma_done+0xd1/0x1e0 [ibtrs_client]
[ 1064.257669] ib_create_qp+0x321/0x380 [ib_core]
[ 1064.257841] ib_process_cq_direct+0xbd/0x120 [ib_core]
[ 1064.258007] irq_poll_softirq+0xb7/0xe0
[ 1064.258165] __do_softirq+0x106/0x2a2
[ 1064.258328] irq_exit+0x92/0xa0
[ 1064.258509] do_IRQ+0x4a/0xd0
[ 1064.258660] common_interrupt+0x7a/0x7a
[ 1064.258818] </IRQ>
Meanwhile another context frees other queue but with the same set of
shared tags:
[ 1288.201183] INFO: task bash:5910 blocked for more than 180 seconds.
[ 1288.201833] bash D 0 5910 5820 0x00000000
[ 1288.202016] Call Trace:
[ 1288.202315] schedule+0x32/0x80
[ 1288.202462] schedule_timeout+0x1e5/0x380
[ 1288.203838] wait_for_completion+0xb0/0x120
[ 1288.204137] __wait_rcu_gp+0x125/0x160
[ 1288.204287] synchronize_sched+0x6e/0x80
[ 1288.204770] blk_mq_free_queue+0x74/0xe0
[ 1288.204922] blk_cleanup_queue+0xc7/0x110
[ 1288.205073] ibnbd_clt_unmap_device+0x1bc/0x280 [ibnbd_client]
[ 1288.205389] ibnbd_clt_unmap_dev_store+0x169/0x1f0 [ibnbd_client]
[ 1288.205548] kernfs_fop_write+0x109/0x180
[ 1288.206328] vfs_write+0xb3/0x1a0
[ 1288.206476] SyS_write+0x52/0xc0
[ 1288.206624] do_syscall_64+0x68/0x1d0
[ 1288.206774] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
What happened is the following:
1. There are several MQ queues with shared tags.
2. One queue is about to be freed and now task is in
blk_mq_del_queue_tag_set().
3. Other CPU is in blk_mq_sched_restart() and loops over all queues in
tag list in order to find hctx to restart.
Because linked list entry was modified in blk_mq_del_queue_tag_set()
without proper waiting for a grace period, blk_mq_sched_restart()
never ends, spining in list_for_each_entry_rcu_rr(), thus soft lockup.
Fix is simple: reinit list entry after an RCU grace period elapsed.
Fixes: Fixes: 705cda97ee3a ("blk-mq: Make it safe to use RCU to iterate over blk_mq_tag_set.tag_list")
Cc: stable@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-block@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
[BUG]
Btrfs can create compressed extent without checksum (even though it
shouldn't), and if we then try to replace device containing such extent,
the result device will contain all the uncompressed data instead of the
compressed one.
Test case already submitted to fstests:
https://patchwork.kernel.org/patch/10442353/
[CAUSE]
When handling compressed extent without checksum, device replace will
goe into copy_nocow_pages() function.
In that function, btrfs will get all inodes referring to this data
extents and then use find_or_create_page() to get pages direct from that
inode.
The problem here is, pages directly from inode are always uncompressed.
And for compressed data extent, they mismatch with on-disk data.
Thus this leads to corrupted compressed data extent written to replace
device.
[FIX]
In this attempt, we could just remove the "optimization" branch, and let
unified scrub_pages() to handle it.
Although scrub_pages() won't bother reusing page cache, it will be a
little slower, but it does the correct csum checking and won't cause
such data corruption caused by "optimization".
Note about the fix: this is the minimal fix that can be backported to
older stable trees without conflicts. The whole callchain from
copy_nocow_pages() can be deleted, and will be in followup patches.
Fixes: ff023aac3119 ("Btrfs: add code to scrub to copy read data to another disk")
CC: stable@vger.kernel.org # 4.4+
Reported-by: James Harvey <jamespharvey20@gmail.com>
Reviewed-by: James Harvey <jamespharvey20@gmail.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
[ remove code removal, add note why ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When snd_ctl_add fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling snd_ctl_add.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When snd_ctl_add fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling snd_ctl_add.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- squash AER directory into drivers/pci/pcie/aer.c (Bjorn Helgaas)
* pci/aer-squash:
PCI/AER: Use "PCI Express" consistently in Kconfig text
PCI/AER: Hoist aerdrv.c, aer_inject.c up to drivers/pci/pcie/
PCI/AER: Squash Kconfig.debug into Kconfig
PCI/AER: Move private AER things to aerdrv.c
PCI/AER: Move aer_irq() declaration to portdrv.h
PCI/AER: Move pcie_aer_get_firmware_first() to portdrv.h
PCI/AER: Remove duplicate pcie_port_bus_type declaration
PCI/AER: Squash ecrc.c into aerdrv.c
PCI/AER: Squash aerdrv_acpi.c into aerdrv.c
PCI/AER: Squash aerdrv_errprint.c into aerdrv.c
PCI/AER: Squash aerdrv_core.c into aerdrv.c
PCI/AER: Reorder code to group probe/remove stuff together
PCI/AER: Remove forward declarations
|
|
- collect all native hardware drivers under drivers/pci/controller/
(Shawn Lin)
* pci/renames:
PCI: Collect all native drivers under drivers/pci/controller/
|
|
Use "PCI Express" consistently in Kconfig text. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Hoist aerdrv.c, aer_inject.c up to drivers/pci/pcie/ so they're next to
other PCIe service drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Squash Kconfig.debug into Kconfig. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Most of the things in aerdrv.h are only used in aerdrv.c, so move them
there. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
The aer_irq() declaration is the only thing needed by aer_inject.c. Move
it to portdrv.h so we eventually get rid of aerdrv.h completely. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Move pcie_aer_get_firmware_first() to portdrv.h, where it can be more
easily shared between AER and DPC. Then DPC no longer needs to include
aer/aerdrv.h. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
pcie_port_bus_type is already declared in portdrv.h, so remove the
unnecessary duplicate declaration in aerdrv.h. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Squash ecrc.c into aerdrv.c. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Squash aerdrv_acpi.c into aerdrv.c. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Squash aerdrv_errprint.c into aerdrv.c. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Squash aerdrv_core.c into aerdrv.c. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Reorder code to group probe/remove stuff together. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Two framebuffer device-node names were looked up during probe, but were
only used as flags to indicate the presence of two framebuffer device.
Drop the unused framebuffer name along with a likewise unused device
pointer from the driver data, and update the platform data to pass in
booleans instead of the framebuffer strings. This allows us do drop the
node references acquired during probe, which would otherwise leak.
Note that there are no other in-kernel users of the modified
platform-data fields.
Fixes: 59eb2b5e57ea ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
This would only cause trouble if the child node is missing while there
is an unrelated node named "backlight" elsewhere in the tree.
Cc: stable <stable@vger.kernel.org> # 3.7
Fixes: eebfdc17cc6c ("backlight: Add TPS65217 WLED driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed,
while the child backlight node was leaked.
Cc: stable <stable@vger.kernel.org> # 3.9
Fixes: 47ec340cb8e2 ("mfd: max8925: Support dt for backlight")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed.
Cc: stable <stable@vger.kernel.org> # 3.10
Fixes: 59eb2b5e57ea ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
I soon won't have access to much MIPS hardware, nor enough time to
properly maintain MIPS on my own, so add Paul Burton as a co-maintainer.
Also add a link to a new shared git repository on kernel.org for
linux-next branches and pull request tags.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Maciej W. Rozycki <macro@mips.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19473/
|
|
gcc complains that urandom_read gets built twice.
gcc -o tools/testing/selftests/bpf/urandom_read
-static urandom_read.c -Wl,--build-id
gcc -Wall -O2 -I../../../include/uapi -I../../../lib -I../../../lib/bpf
-I../../../../include/generated -I../../../include urandom_read.c
urandom_read -lcap -lelf -lrt -lpthread -o
tools/testing/selftests/bpf/urandom_read
gcc: fatal error: input file
‘tools/testing/selftests/bpf/urandom_read’ is the
same as output file
compilation terminated.
../lib.mk:110: recipe for target
'tools/testing/selftests/bpf/urandom_read' failed
To fix this issue remove the urandom_read target and so target
TEST_CUSTOM_PROGS gets used.
Fixes: 81f77fd0deeb ("bpf: add selftest for stackmap with BPF_F_STACK_BUILD_ID")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Check the max speed supported from the fuses for i.MX6ULL and update the
operating points table accordingly.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This function is no longer called, so we get a harmless
warning until it is removed as well:
drivers/mfd/cros_ec_dev.c:265:13: error: '__remove' defined but not used [-Werror=unused-function]
Fixes: 3aa2177e4787 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
It is not mandatory that platform data is passed along the ac97
codec. Actually there are configuration without a battery connected to
the ADC of the codec.
This is for example the case for the PXA zylonite platform, so fix the
NULL dereferencing by adding a test.
Fixes: a5c6951c49fb ("mfd: wm97xx-core: core support for wm97xx Codec")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
... getting rid of transformations in the latter - just use
compat_import_iovec().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull networking fixes from David Miller:
1) Fix several bpfilter/UMH bugs, in particular make the UMH build not
depend upon X86 specific Kconfig symbols. From Alexei Starovoitov.
2) Fix handling of modified context pointer in bpf verifier, from
Daniel Borkmann.
3) Kill regression in ifdown/ifup sequences for hv_netvsc driver, from
Dexuan Cui.
4) When the bonding primary member name changes, we have to re-evaluate
the bond->force_primary setting, from Xiangning Yu.
5) Eliminate possible padding beyone end of SKB in cdc_ncm driver, from
Bjørn Mork.
6) RX queue length reported for UDP sockets in procfs and socket diag
are inaccurate, from Paolo Abeni.
7) Fix br_fdb_find_port() locking, from Petr Machata.
8) Limit sk_rcvlowat values properly in TCP, from Soheil Hassas
Yeganeh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
tcp: limit sk_rcvlowat by the maximum receive buffer
net: phy: dp83822: use BMCR_ANENABLE instead of BMSR_ANEGCAPABLE for DP83620
socket: close race condition between sock_close() and sockfs_setattr()
net: bridge: Fix locking in br_fdb_find_port()
udp: fix rx queue len reported by diag and proc interface
cdc_ncm: avoid padding beyond end of skb
net/sched: act_simple: fix parsing of TCA_DEF_DATA
net: fddi: fix a possible null-ptr-deref
net: aquantia: fix unsigned numvecs comparison with less than zero
net: stmmac: fix build failure due to missing COMMON_CLK dependency
bpfilter: fix race in pipe access
bpf, xdp: fix crash in xdp_umem_unaccount_pages
xsk: Fix umem fill/completion queue mmap on 32-bit
tools/bpf: fix selftest get_cgroup_id_user
bpfilter: fix OUTPUT_FORMAT
umh: fix race condition
net: mscc: ocelot: Fix uninitialized error in ocelot_netdevice_event()
bonding: re-evaluate force_primary when the primary slave name changes
ip_tunnel: Fix name string concatenate in __ip_tunnel_create()
hv_netvsc: Fix a network regression after ifdown/ifup
...
|
|
When kconfig syntax moved to use $(FOO) for environment variables
localmodconfig was not updated.
Fix so it now works with the new syntax $(FOO)
Fixes: 104daea149c4 ("kconfig: reference environment variables directly and remove 'option env='")
Reported-by: Kevin Locke <kevin@kevinlocke.name>
Reported-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Kevin Locke <kevin@kevinlocke.name>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
VMLINUX_SYMBOL() is no-op unless CONFIG_HAVE_UNDERSCORE_SYMBOL_PREFIX
is defined. It has ever been selected only by BLACKFIN and METAG.
VMLINUX_SYMBOL() is unneeded for SuperH-specific code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This eliminates the workaround that requires disabling
-mprofile-kernel by default in Kconfig.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
It would be nice if the source code is written in the same style.
This proposes the convention for describing the compiler capability
in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
We have enabled GCC_PLUGINS for COMPILE_TEST, but allmodconfig now
produces new warnings.
CC [M] drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.o
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_workarounds_nphy_rev7’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:16563:1: warning: the frame size of 3128 bytes is larger than 2048 bytes [-Wframe-larger-than=]
}
^
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_workarounds_nphy_rev3’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:16905:1: warning: the frame size of 2800 bytes is larger than 2048 bytes [-Wframe-larger-than=]
}
^
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_cal_txiqlo_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:26033:1: warning: the frame size of 2488 bytes is larger than 2048 bytes [-Wframe-larger-than=]
}
^
It looks like GCC_PLUGIN_STRUCTLEAK_BYREF_ALL is causing this.
Add "depends on !COMPILE_TEST" to not dirturb the compile test.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
