| Age | Commit message (Collapse) | Author |
|---|
|
Use the generic stmmac_set_clk_tx_rate() to configure the MAC transmit
clock.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Use the generic stmmac_set_clk_tx_rate() to configure the MAC transmit
clock.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Place register number definitions immediately above their field
definitions and order by register number.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
We only need to enable the MAC receiver and transmiter only when the
link has come up.
With commit "net: stmmac: move phylink_resume() after resume setup
is complete" we move the race between stmmac_mac_link_up() and
stmmac_hw_setup(), ensuring that stmmac_mac_link_up() happens
afterwards. This patch is a pre-requisit of this change.
Remove the unnecessary call to stmmac_mac_set(, true) in
stmmac_hw_setup().
Tested-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Remove fiddling with _TE and _RE in the GMAC control register in the
start_tx/stop_tx/start_rx/stop_rx() methods as this should be handled
by stmmac_mac_link_up() and stmmac_mac_link_down() and not during
initialisation.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
stmmac_release() calls phylink_stop() and then goes on to call
stmmac_mac_set(, false). However, phylink_stop() will call
stmmac_mac_link_down() before returning, which will do this work.
Remove this unnecessary call.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
While the network device is registered, it is published to userspace,
and thus userspace can change its state. This means calling
functions such as stmmac_stop_all_dma() and stmmac_mac_set() are
racy.
Moreover, unregister_netdev() will unpublish the network device, and
then if appropriate call the .ndo_stop() method, which is
stmmac_release(). This will first call phylink_stop() which will
synchronously take the link down, resulting in stmmac_mac_link_down()
and stmmac_mac_set(, false) being called.
stmmac_release() will also call stmmac_stop_all_dma().
Consequently, neither of these two functions need to called prior
to unregister_netdev() as that will safely call paths that will
result in this work being done if necessary.
Remove these redundant racy calls.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Phylink does not permit drivers to mess with the netif carrier, as
this will de-synchronise phylink with the MAC driver. Moreover,
setting and clearing the TE and RE bits via stmmac_mac_set() in this
path is also wrong as the link may not be up.
Replace the netif_carrier_on(), netif_carrier_off() and
stmmac_mac_set() calls with the appropriate phylink_start() and
phylink_stop() calls, thereby allowing phylink to manage the netif
carrier and TE/RE bits through the .mac_link_up() and .mac_link_down()
methods.
Note that RE should only be set after the DMA is ready to avoid the
receive FIFO between the MAC and DMA blocks overflowing, so
phylink_start() needs to be placed after DMA has been started.
Tested-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The Synopsys Designwavre GMAC core databook requires all clocks to be
active in order to complete software reset.
This means if the PHY receive clock has been stopped due to the media
being in EEE low-power state, and the PHY being permitted to stop its
clock, then software reset will not complete.
Phylink now provides a way to work around this by calling
phylink_prepare_resume() before attempting to issue a reset. This will
prepare any attached PHY by disabling its permission to stop the clock.
phylink_resume() will restore the receive clock stop setting according
to the configuration passed from the netdev driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Move phylink_resume() to be after the setup in stmmac_resume() has
completed, as phylink_resume() may result in an immediate call to the
.mac_link_up method, which will enable the transmitter and receiver,
and enable the transmit queues.
This behaviour has been witnessed by Jon Hunter on the Jetson TX2
platform (Tegra 186).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Currently, the calls to phylink's suspend and resume functions are
inside overly complex tests, and boil down to:
if (device_may_wakeup(priv->device) && priv->plat->pmt) {
call phylink
} else {
call phylink and
if (device_may_wakeup(priv->device))
do something else
}
This results in phylink always being called, possibly with differing
arguments for phylink_suspend().
Simplify this code, noting that each site is slightly different due to
the order in which phylink is called and the "something else".
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Add a resume preparation function, which will ensure that the receive
clock from the PHY is appropriately configured while resuming.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Add configuration of the receive clock-stop in phylink_resume() to
ensure that the clock-stop is correctly configured.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Switch from using the fix_mac_speed() hook to set_clk_tx_rate() to
manage the transmit clock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Switch from using the fix_mac_speed() hook to set_clk_tx_rate() to
manage the transmit clock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Switch from using the fix_mac_speed() hook to set_clk_tx_rate() to
manage the transmit clock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Switch from using the fix_mac_speed() hook to set_clk_tx_rate() to
manage the transmit clock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert non-i.MX93 users to use the generic stmmac_set_clk_tx_rate() to
configure the MAC transmit clock rate.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Use the generic stmmac_set_clk_tx_rate() to configure the MAC transmit
clock.
Note that given the current unpatched driver structure,
plat_dat->fix_mac_speed will always be populated with
kmb_eth_fix_mac_speed(), even when no clock is present. We preserve
this behaviour in this patch by always initialising plat_dat->clk_tx_i
and plat_dat->set_clk_tx_rate.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Use the generic stmmac_set_clk_tx_rate() to configure the MAC transmit
clock.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Use the generic stmmac_set_clk_tx_rate() to configure the MAC transmit
clock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Provide a generic implementation for the set_clk_tx_rate method
introduced by the previous patch, which is capable of configuring the
MAC transmit clock for 10M, 100M and 1000M speeds for at least MII,
GMII, RGMII and RMII interface modes.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Several stmmac sub-drivers which support RGMII follow the same pattern.
They calculate the transmit clock rate, and then call clk_set_rate().
Analysis of several implementation documents suggests that the platform
is responsible for providing the transmit clock to the DWMAC core's
clk_tx_i. The expected rates are:
10Mbps 100Mbps 1Gbps
MII 2.5MHz 25MHz
RMII 2.5MHz 25MHz
GMII 125MHz
RGMI 2.5MHz 25MHz 125MHz
It seems some platforms require this clock to be manually configured,
but there are outputs from the MAC core that indicate the speed, so a
platform may use these to automatically configure the clock. Thus, we
can't just provide one solution to configure this clock rate.
Moreover, the clock may need to be derived from one of several sources
depending on the interface mode.
Provide a platform hook that is passed the transmit clock, interface
mode and speed.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Most of the stmmac driver uses "plat_dat" to name the platform data,
and "data" is used for the glue driver data. make dwc-qos follow
this pattern to avoid silly mistakes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
thead was checking that the stmmac_clk rate was a multiple of the
RGMII rates for 1G and 100M, but didn't check for 10M. Rather than
use this with hard-coded speeds, check that the calculated divisor
gives the required rate by multplying the transmit clock rate back
up to the stmmac clock rate and checking that it agrees.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Switch to using rgmii_clock() to get the RGMII TXC rate, and calculate
the divisor from the parent clock rate and the rate indicated by
rgmii_clock().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The link clock operates at twice the RGMII clock rate. Therefore, we
can use the rgmii_clock() helper to set this clock rate.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
stmmac_init_dma_engine() uses dev_err() which leads to errors being
reported as e.g:
dwc-eth-dwmac 2490000.ethernet: Failed to reset the dma
dwc-eth-dwmac 2490000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
stmmac_init_dma_engine() is only called from stmmac_hw_setup() which
itself uses netdev_err(), and we will have a net_device setup. So,
change the dev_err() to netdev_err() to give consistent error
messages.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tl5y1-004UgG-8X@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
priv->plat->fix_mac_speed() is called from stmmac_mac_link_up(), which
is passed the speed as an "int". However, fix_mac_speed() implicitly
casts this to an unsigned int. Some platform glue code print this value
using %u, others with %d. Some implicitly cast it back to an int, and
others to u32.
Good practice is to use one type and only one type to represent a value
being passed around a driver.
Switch all of these over to consistently use "int" when dealing with a
speed passed from stmmac_mac_link_up(), even though the speed will
always be positive.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://patch.msgid.link/E1tkKmN-004ObM-Ge@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
priv->flow_ctrl is only accessed by stmmac_main.c, and the only place
that it is read is in stmmac_mac_flow_ctrl(). This function is only
called from stmmac_mac_link_up() which always sets priv->flow_ctrl
immediately before calling this function.
Therefore, initialising this at probe time is ineffectual because it
will always be overwritten before it's read. As such, the "flow_ctrl"
module parameter has been useless for some time. Rather than remove
the module parameter, which would risk module load failure, change the
description to indicate that it is obsolete, and warn if it is set by
userspace.
Moreover, storing the value in the stmmac_priv has no benefit as it's
set and then immediately read stmmac_mac_flow_ctrl(). Instead, pass it
as a parameter to this function..
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://patch.msgid.link/E1tkKmI-004ObG-DL@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
priv->pause corresponds with "pause_time" in the 802.3 specification,
and is also called "pause_time" in the various MAC backends. For
consistency, use the same name in the core stmmac code.
Clarify the units of the "pause" module parameter which sets up this
struct member to indicate that it's in units of the pause_quanta
defined by 802.3, which is 512 bit times.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Link: https://patch.msgid.link/E1tkKmD-004ObA-9K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move xpcs_config_eee() with the other EEE-related functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
There is now no need to pass the mult_fact into xpcs_config_eee(), so
let's remove that argument and use xpcs->eee_mult_fact directly. While
changing the function signature, as we pass true/false for enable, use
"bool" instead of "int" for this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Make xpcs_config_eee() private to the XPCS driver, called only from
the phylink pcs_disable_eee() and pcs_enable_eee() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Remove the explicit calls to xpcs_config_eee() from the stmmac driver,
preferring instead for phylink to manage the EEE configuration at the
PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert XPCS to use the new pcs_disable_eee() and pcs_enable_eee()
methods. Since stmmac is the only user of xpcs_config_eee(), we can
make this a no-op along with this change.
Questions:
1. Do we actually need this level of control at the PCS - or would it
be sufficient to configure it once during initialisation?
2. Do we need to clear the mult_fact field when disabling EEE?
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Arrange for stmmac to call the new xpcs_config_eee_mult_fact() function
to configure the EEE clock multiplying factor. This will allow the
removal of the xpcs_config_eee() calls in the next patch.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Add a function to separate out the EEE clock multiplying factor. This
will be called by the stmmac driver to configure this value.
It would have been better had the driver used the CLK API to retrieve
this clock, get its rate and calculate the appropriate multiplier, but
that door has closed.
Question: Is there any other solution to this so we can avoid keeping
this XPCS-specific function that MAC drivers have to know about if
they are going to use EEE with XPCS?
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
There are hooks in the stmmac driver into XPCS to control the EEE
settings when LPI is configured at the MAC. This bypasses the layering.
To allow this to be removed from the stmmac driver, add two new
methods for PCS to inform them when the LPI/EEE enablement state
changes at the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Fixme: doesn't bit 25 and 26 also need to be set in the PMCR for
PMCR_FORCE_EEE100 and PMCR_FORCE_EEE1G to take effect?
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
In order to allow DSA drivers to use phylink managed EEE, we need to
change the behaviour of the DSA's .set_eee() ethtool method.
Implementation of the DSA .set_mac_eee() method becomes optional with
phylink managed EEE as it is only used to validate the EEE parameters
supplied from userspace. The rest of the EEE state management should
be left to phylink.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Provide a helper to determine whether the MAC operations structure
implements the LPI operations, which will be used by both phylink and
DSA.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
As we no longer call the set_eee_mode(), reset_eee_mode() and
set_eee_lpi_entry_timer() methods, remove these and their glue in
common.h
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Use the new stmmac_set_lpi_mode() API to configure the parameters of
the desired LPI mode rather than the older methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Ensure that LPI_CTRL_STATUS_LPITCSE is also appropriately cleared when
disabling LPI or enabling LPI without TX clock gating.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Add a new method to control LPI mode configuration. This is architected
to have three configuration states: LPI disabled, LPI forced (active),
or LPI under hardware timer control. This reflects the three modes
which the main body of the driver wishes to deal with.
We pass in whether transmit clock gating should be used, and the
hardware timer value in microseconds to be set when using hardware
timer control.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The bit definitions for the LPI control/status register are
identical across all MAC versions, with the exception that some
bits may not be implemented. Provide definitions for bits in this
register in common.h, convert to use them, and remove the core-
specific definitions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Remove the unnecessary LPI disable when enabling LPI - as noted in
previous commits, there will never be two consecutive calls to
stmmac_mac_enable_tx_lpi() without an intervening
stmmac_mac_disable_tx_lpi.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
As other code paths do, clear priv->tx_path_in_lpi_mode when disabling
LPI. This is done after the software timer has been deleted and
hardware LPI has been disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Phylink will not call the mac_disable_tx_lpi() and mac_enable_tx_lpi()
methods randomly - the first method to be called will be the enable
method, and then after, the disable method will be called once between
subsequent enable calls. Thus there is a guaranteed ordering.
Therefore, we know the previous state of priv->eee_enabled, and can
remove it from both methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
