| Age | Commit message (Collapse) | Author |
|---|
|
In a previous series, we made sure that FDMA was not initialized and
started on lan969x. Now that we are going to support it, undo that
change. In addition, make sure the chip ID check is only applicable on
Sparx5, as this is a check that is only relevant on this platform.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20250113-sparx5-lan969x-switch-driver-5-v2-1-c468f02fd623@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
net: phylink: fix PCS without autoneg
Eric Woudstra reported that a PCS attached using 2500base-X does not
see link when phylink is using in-band mode, but autoneg is disabled,
despite there being a valid 2500base-X signal being received. We have
these settings:
act_link_an_mode = MLO_AN_INBAND
pcs_neg_mode = PHYLINK_PCS_NEG_INBAND_DISABLED
Eric diagnosed it to phylink_decode_c37_word() setting state->link
false because the full-duplex bit isn't set in the non-existent link
partner advertisement word (which doesn't exist because in-band
autoneg is disabled!)
The test in phylink_mii_c22_pcs_decode_state() is supposed to catch
this state, but since we converted PCS to use neg_mode, testing the
Autoneg in the local advertisement is no longer sufficient - we need
to be looking at the neg_mode, which currently isn't provided.
We need to provide this via the .pcs_get_state() method, and this
will require modifying all PCS implementations to add the extra
argument to this method.
Patch 1 uses the PCS neg_mode in phylink_mac_pcs_get_state() to correct
the now obsolute usage of the Autoneg bit in the advertisement.
Patch 2 passes neg_mode into the .pcs_get_state() method, and updates
all users.
Patch 3 adds neg_mode as an argument to the various clause 22 state
decoder functions in phylink, modifying drivers to pass the neg_mode
through.
Patch 4 makes use of phylink_mii_c22_pcs_decode_state() rather than
using the Autoneg bit in the advertising field.
Patch 5 may be required for Eric's case - it ensures that we report
the correct state for interface types that we support only one set
of modes for when autoneg is disabled.
====================
Link: https://patch.msgid.link/Z4TbR93B-X8A8iHe@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When decoding clause 22 state, if in-band is disabled and using either
1000base-X or 2500base-X, rather than reporting link-down, we know the
speed, and we only support full duplex. Pause modes taken from XPCS.
This fixes a problem reported by Eric Woudstra.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGei-000EtL-Fn@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rather than using the state of the Autoneg bit, which is unreliable
with the new PCS neg mode support, use the passed neg_mode to decide
whether to decode the link partner advertisement data.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGed-000EtF-CN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass the current neg_mode into phylink_mii_c22_pcs_get_state() and
phylink_mii_c22_pcs_decode_state(). Update all users of phylink PCS
that use these functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeY-000Et9-8g@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As in-band AN no longer just depends on MLO_AN_INBAND + Autoneg bit,
we need to take account of the pcs_neg_mode when deciding how to
initialise the speed, duplex and pause state members before calling
into the .pcs_neg_mode() method. Add this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeO-000Esx-0r@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Matthieu Baerts says:
====================
mptcp: selftests: more debug in case of errors
Here are just a bunch of small improvements for the MPTCP selftests:
Patch 1: Unify errors messages in simult_flows: print MIB and 'ss -Me'.
Patch 2: Unify errors messages in sockopt: print MIB.
Patch 3: Move common code to print debug info to mptcp_lib.sh.
Patch 4: Use 'ss' with '-m' in case of errors.
Patch 5: Remove an unused variable.
Patch 6: Print only the size instead of size + filename again.
====================
Link: https://patch.msgid.link/20250114-net-next-mptcp-st-more-debug-err-v1-0-2ffb16a6cf35@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'du' will print the name of the file, which was already displayed
before, e.g.
Created /tmp/tmp.UOyy0ghfmQ (size 4703740/tmp/tmp.UOyy0ghfmQ) containing data sent by client
Created /tmp/tmp.xq3zvFinGo (size 1391724/tmp/tmp.xq3zvFinGo) containing data sent by server
'stat' can be used instead, to display this instead:
Created /tmp/tmp.UOyy0ghfmQ (size 4703740 B) containing data sent by client
Created /tmp/tmp.xq3zvFinGo (size 1391724 B) containing data sent by server
So easier to spot the file sizes.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250114-net-next-mptcp-st-more-debug-err-v1-6-2ffb16a6cf35@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'cin_disconnect' is used in run_tests_disconnect(), but not
'cout_disconnect', so it is safe to drop it.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250114-net-next-mptcp-st-more-debug-err-v1-5-2ffb16a6cf35@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recently, we had an issue where getting info about the memory would have
helped better understanding what went wrong.
Let add it just in case for later.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250114-net-next-mptcp-st-more-debug-err-v1-4-2ffb16a6cf35@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A few MPTCP selftests are using the same code to print stats in case of
error. This code can then be moved to mptcp_lib.sh.
No behaviour changes intended, except to print the error in red and to
stderr, like most error messages.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250114-net-next-mptcp-st-more-debug-err-v1-3-2ffb16a6cf35@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Similar to the way nstat information is stored in mptcp_connect.sh
and mptcp_join.sh scripts, this patch adds a similar way for
mptcp_sockopt.sh and displays the nstat information when errors
occur.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250114-net-next-mptcp-st-more-debug-err-v1-2-2ffb16a6cf35@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to unify what is printed in case of error, similar to what is
done in mptcp_connect.sh and mptcp_join.sh, it is interesting to do the
following modifications in simult_flows.sh:
- Print the rc errors at the end of the line.
- Print the MIB counters.
- Use the same ss options: add -M (MPTCP sockets) and -e (detailed
socket information).
While at it, also print of the 'max' time only in case of success,
because 'mptcp_connect.c' will already print this info in case of error,
e.g.:
transfer slower than expected! runtime 11948 ms, expected 11921 ms
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250114-net-next-mptcp-st-more-debug-err-v1-1-2ffb16a6cf35@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 1c670b39cec7 ("mptcp: change local addr type of subflow_destroy")
introduced a bug in mptcp_pm_nl_subflow_destroy_doit().
ipv6_addr_set_v4mapped() should be called to set the remote ipv4 address
'addr_r.addr.s_addr' to the remote ipv6 address 'addr_r.addr6', not
'addr_l.addr.addr6', which is the local ipv6 address.
Fixes: 1c670b39cec7 ("mptcp: change local addr type of subflow_destroy")
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250114-net-next-mptcp-fix-remote-addr-v1-1-debcd84ea86f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
net: bcm: asp2: fix fallout from phylib EEE changes
This series addresses the fallout from the phylib changes in the
Broadcom ASP2 driver.
The first patch uses phylib's copy of the LPI timer setting, which
means the driver no longer has to track this. It will be set in
hardware each time the adjust_link function is called when the link
is up, and will be read at initialisation time to set the current
value.
The second patch removes the driver's storage of tx_lpi_enabled,
which has become redundant since phylib managed EEE was merged. The
driver does nothing with this flag other than storing it.
The last patch converts the driver to use phylib's enable_tx_lpi
flag rather than trying to maintain its own copy.
====================
Link: https://patch.msgid.link/Z4aV3RmSZJ1WS3oR@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the Broadcom ASP2 driver to use phylib managed EEE support.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/E1tXk81-000r4x-TS@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Phylib maintains a copy of tx_lpi_enabled, which will be used to
populate the member when phy_ethtool_get_eee(). Therefore, writing to
this member before phy_ethtool_get_eee() will have no effect. Remove
it. Also remove setting our copy of info->eee.tx_lpi_enabled which
becomes write-only.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/E1tXk7w-000r4r-Pq@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the LPI timer handling in Broadcom ASP2 driver after the phylib
managed EEE patches were merged.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/E1tXk7r-000r4l-Li@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
net: stmmac: further EEE cleanups (and one fix!)
This series continues the EEE cleanup of the stmmac driver, and
includes one fix.
As mentioned in the previous series, I wasn't entirely happy with the
"stmmac_disable_sw_eee_mode" name, so the first patch renames this to
"stmmac_stop_sw_lpi" instead, which I think better describes what this
function is doing - stopping the transmit of the LPI state because we
have a packet ot send.
Patch 2 corrects the priv->eee_sw_timer_en flag when EEE has been
disabled. Currently upon disable, priv->eee_enabled is set false,
but through the weird logic that was present prior to the previous
series, priv->eee_sw_timer_en was set true. This behaviour was kept
as the previous series was cleanup, not fixes. This patch fixes this.
Having fixed priv->eee_sw_timer_en to actually indicate whether
software timed EEE mode is being used, it becomes no longer necessary
to test priv->eee_enabled in addition. Patch 3 removes the redundant
test. Patch 4 also uses priv->eee_sw_timer_en before manipulating the
software EEE state in the suspend method rather than using
priv->eee_enabled, which brings consistency.
Patch 5 provides stmmac_try_to_start_sw_lpi() which complements
stmmac_stop_sw_lpi(), and allows us to move duplicated code into one
location.
Patch 6 splits stmmac_enable_eee_mode() - one part of this function
tests whether there are any queues that have unfinished work (in
other words are busy). Separate out this code into a separate function.
Patch 7 also splits out the mod_timer() for the software EEE timer
intoi a seperate function (the reason will be in patch 9.)
Patch 8 merges the remains of stmmac_enable_eee_mode() into
stmmac_try_to_start_sw_lpi().
Patch 9 fixes the delay between transmit and entering LPI. Currently,
when cleaning the transmit queues, if we discover that we have finished
cleaning up all queues, we immediately instruct the hardware to enter
LPI mode without waiting for the LPI timer. However, we should wait for
the LPI timer to expire. Therefore, the transmit cleanup path needs
to call stmmac_restart_sw_lpi_timer() instead of
stmmac_try_to_start_sw_lpi().
====================
Link: https://patch.msgid.link/Z4T84SbaC4D-fN5y@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix a bug in the LPI handling, where it is possible to immediately
enter LPI mode after cleaning the transmit descriptors when all queues
are empty rather than waiting for the LPI timeout to expire.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXItg-000MBg-TW@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Combine stmmac_enable_eee_mode() with stmmac_try_to_start_sw_lpi()
which makes the code easier to read and the flow more logical. We
can now trivially see that if the transmit queues are busy, we
(re-)start the eee_ctrl_timer. Otherwise, if the transmit path is
not already in LPI mode, we ask the hardware to enter LPI mode.
I believe that now we can see better what is going on here, this
shows that there is a bug with the software LPI timer implementation.
The LPI timer is supposed to define how long after the last
transmittion completed before we start signalling LPI. However,
this code structure shows that if all transmit queues are empty,
and stmmac_try_to_start_sw_lpi() is called immediately after cleaning
the transmit queue, we will instruct the hardware to start signalling
LPI immediately.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXItb-000MBa-OU@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a function that encapsulates restarting the software LPI
timer when we have determined that the transmit path is busy, or
whether the EEE parameters have changed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXItW-000MBU-KQ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extract the code which checks whether there's still work to do on any
of the stmmac transmit queues. This will allow us to combine
stmmac_enable_eee_mode() with stmmac_try_to_start_sw_lpi() in the
next patch.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXItR-000MBO-GF@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are two places which call stmmac_enable_eee_mode() and follow it
immediately by modifying the expiry of priv->eee_ctrl_timer. Both code
paths are trying to enable LPI mode. Remove this duplication by
providing a function for this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXItM-000MBI-CX@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The suspend path uses priv->eee_enabled when cleaning up the software
timed LPI mode. Use priv->eee_sw_timer_en instead so we're consistently
using a single control for software-based timer handling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXItH-000MBC-8i@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As mentioned in "net: stmmac: correct priv->eee_sw_timer_en setting",
we can simplify some fast-path tests.
The transmit cleaning path checks whether EEE is enabled, the transmit
path is not in LPI mode, and that we're using software timed mode.
Since the above mentioned commit, checking whether EEE is enabled is
no longer necessary as priv->eee_sw_timer_en will be false when EEE is
disabled. Simplify this test.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXItC-000MB6-54@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we are disabling EEE/LPI, then we should not be enabling software
mode. The only time when we should is if EEE is active, and we are
wanting to use software-timed EEE mode.
Therefore, in the disable path of stmmac_eee_init(), ensure that
priv->eee_sw_timer_en is set false as we are going to be calling
del_timer_sync() on the timer.
This will allow us to simplify some fast-path tests in later patches.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXIt7-000MB0-0W@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
stmmac_disable_sw_eee_mode() was not a good choice for this functions
purpose - which is to stop transmitting LPI because we want to send a
packet. Rename it to stmmac_stop_sw_lpi().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tXIt1-000MAu-TE@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device ioctl handler no longer calls ndo_do_ioctl, but calls
ndo_eth_ioctl to handle mii ioctls since commit a76053707dbf
("dev_ioctl: split out ndo_eth_ioctl"). However, sunplus still used
ndo_do_ioctl when it was introduced. So switch to ndo_eth_ioctl.
Bad commit fd3040b9394c ("net: ethernet: Add driver for Sunplus SP7021")
was the initial driver commit, meaning that PHY IOCTLs where never
available on this driver. Therefore don't consider this as a fix.
Found by code inspection.
Signed-off-by: 谢致邦 (XIE Zhibang) <Yeking@Red54.com>
Link: https://patch.msgid.link/tencent_8CF8A72C708E96B9C7DC1AF96FEE19AF3D05@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Krzysztof Kozlowski says:
====================
net: ethernet: Simplify few things
Few code simplifications without functional impact.
Not tested on hardware.
====================
Link: https://patch.msgid.link/20250112-syscon-phandle-args-net-v1-0-3423889935f7@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250112-syscon-phandle-args-net-v1-5-3423889935f7@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250112-syscon-phandle-args-net-v1-4-3423889935f7@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250112-syscon-phandle-args-net-v1-3-3423889935f7@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250112-syscon-phandle-args-net-v1-2-3423889935f7@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Debugging messages should not reveal anything about memory addresses.
This also solves arm compile test warnings:
drivers/net/ethernet/ti/icssg/icssg_prueth_sr1.c:1034:49: error:
format specifies type 'unsigned long long' but the argument has type 'phys_addr_t' (aka 'unsigned int') [-Werror,-Wformat]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20250112-syscon-phandle-args-net-v1-1-3423889935f7@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The last use of kernel_sendmsg_locked() was removed in 2023 by
commit dc97391e6610 ("sock: Remove ->sendpage*() in favour of
sendmsg(MSG_SPLICE_PAGES)")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250112131318.63753-1-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'struct mdio_device_id' is not modified in these drivers.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
27014 12792 0 39806 9b7e drivers/net/phy/broadcom.o
After:
=====
text data bss dec hex filename
27206 12600 0 39806 9b7e drivers/net/phy/broadcom.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/403c381b7d9156b67ad68ffc44b8eee70c5e86a9.1736691226.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Heiner Kallweit says:
====================
net: phy: realtek: add hwmon support
This adds hwmon support for the temperature sensor on RTL822x.
It's available on the standalone versions of the PHY's, and on the
internal PHY's of RTL8125B(P)/RTL8125D/RTL8126.
====================
Link: https://patch.msgid.link/7319d8f9-2d6f-4522-92e8-a8a4990042fb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This adds hwmon support for the temperature sensor on RTL822x.
It's available on the standalone versions of the PHY's, and on
the integrated PHY's in RTL8125B/RTL8125D/RTL8126.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/ad6bfe9f-6375-4a00-84b4-bfb38a21bd71@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of adding a source file with hwmon support, move the
Realtek PHY driver to its own subdirectory and rename realtek.c to
realtek_main.c.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/c566551b-c915-4e34-9b33-129a6ddd6e4c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RTL8125/RTL8126
RTL8125/RTL8126 don't support MMD access to the internal PHY, but
provide a mechanism to access at least all MDIO_MMD_VEND2 registers.
By exposing this mechanism standard MMD access functions can be used
to access the MDIO_MMD_VEND2 registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/e821b302-5fe6-49ab-aabd-05da500581c0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
EN7581 SoC supports fixed QoS band priority where WRR queues have lowest
priorities with respect to SP ones.
E.g: WRR0, WRR1, .., WRRm, SP0, SP1, .., SPn
Enforce ETS Qdisc priomap according to the hw capabilities.
Suggested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Link: https://patch.msgid.link/20250112-airoha_ets_priomap-v1-1-fb616de159ba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Only configure VLAN-aware CPSW mode if no port is used as DSA CPU port.
VLAN-aware mode interferes with some DSA tagging schemes and makes stacking
DSA switches downstream of CPSW impossible. Previous attempts to address
the issue linked below.
Link: https://lore.kernel.org/netdev/20240227082815.2073826-1-s-vadapalli@ti.com/
Link: https://lore.kernel.org/linux-arm-kernel/4699400.vD3TdgH1nR@localhost/
Co-developed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://patch.msgid.link/20250110125737.546184-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use netif_queue_set_napi() to link queues to NAPI instances so that they
can be queried with netlink.
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump queue-get --json='{"ifindex": 11}'
[{'id': 0, 'ifindex': 11, 'napi-id': 9, 'type': 'rx'},
{'id': 1, 'ifindex': 11, 'napi-id': 10, 'type': 'rx'},
{'id': 0, 'ifindex': 11, 'napi-id': 9, 'type': 'tx'},
{'id': 1, 'ifindex': 11, 'napi-id': 10, 'type': 'tx'}]
Additionally use netif_napi_set_irq() to also provide NAPI interrupt
number to userspace.
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--do napi-get --json='{"id": 9}'
{'defer-hard-irqs': 0,
'gro-flush-timeout': 0,
'id': 9,
'ifindex': 11,
'irq': 42,
'irq-suspend-timeout': 0}
Providing information about queues to userspace makes sense as APIs like
XSK provide queue specific access. Also XSK busy polling relies on
queues linked to NAPIs.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20250110223939.37490-1-gerhard@engleder-embedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
HW can have different input/output delays for each of the pins.
Currently, only E82X adapters have delay compensation based on TSPLL
config and E810 adapters have constant 1 ms compensation, both cases
only for output delays and the same one for all pins.
E825 adapters have different delays for SDP and other pins. Those
delays are also based on direction and input delays are different than
output ones. This is the main reason for moving delays to pin
description structure.
Add a field in ice_ptp_pin_desc structure to reflect that. Delay values
are based on approximate calculations of HW delays based on HW spec.
Implement external timestamp (input) delay compensation.
Remove existing definitions and wrappers for periodic output propagation
delays.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Programming the PHY registers in preparation for an increment value change
or a timer adjustment on E810 requires issuing Admin Queue commands for
each PHY register. It has been found that the firmware Admin Queue
processing occasionally has delays of tens or rarely up to hundreds of
milliseconds. This delay cascades to failures in the PTP applications which
depend on these updates being low latency.
Consider a standard PTP profile with a sync rate of 16 times per second.
This means there is ~62 milliseconds between sync messages. A complete
cycle of the PTP algorithm
1) Sync message (with Tx timestamp) from source
2) Follow-up message from source
3) Delay request (with Tx timestamp) from sink
4) Delay response (with Rx timestamp of request) from source
5) measure instantaneous clock offset
6) request time adjustment via CLOCK_ADJTIME systemcall
The Tx timestamps have a default maximum timeout of 10 milliseconds. If we
assume that the maximum possible time is used, this leaves us with ~42
milliseconds of processing time for a complete cycle.
The CLOCK_ADJTIME system call is synchronous and will block until the
driver completes its timer adjustment or frequency change.
If the writes to prepare the PHY timers get hit by a latency spike of 50
milliseconds, then the PTP application will be delayed past the point where
the next cycle should start. Packets from the next cycle may have already
arrived and are waiting on the socket.
In particular, LinuxPTP ptp4l may start complaining about missing an
announce message from the source, triggering a fault. In addition, the
clockcheck logic it uses may trigger. This clockcheck failure occurs
because the timestamp captured by hardware is compared against a reading of
CLOCK_MONOTONIC. It is assumed that the time when the Rx timestamp is
captured and the read from CLOCK_MONOTONIC are relatively close together.
This is not the case if there is a significant delay to processing the Rx
packet.
Newer firmware supports programming the PHY registers over a low latency
interface which bypasses the Admin Queue. Instead, software writes to the
REG_LL_PROXY_L and REG_LL_PROXY_H registers. Firmware reads these registers
and then programs the PHY timers.
Implement functions to use this interface when available to program the PHY
timers instead of using the Admin Queue. This avoids the Admin Queue
latency and ensures that adjustments happen within acceptable latency
bounds.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Newer versions of firmware support programming the PHY timer via the low
latency interface exposed over REG_LL_PROXY_L and REG_LL_PROXY_H. Add
support for checking the device capabilities for this feature.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Newer firmware for the E810 devices support a 'low latency' interface to
interact with the PHY without using the Admin Queue. This is interacted
with via the REG_LL_PROXY_L and REG_LL_PROXY_H registers.
Currently, this interface is only used for Tx timestamps. There are two
different mechanisms, including one which uses an interrupt for firmware to
signal completion. However, these two methods are mutually exclusive, so no
synchronization between them was necessary.
This low latency interface is being extended in future firmware to support
also programming the PHY timers. Use of the interface for PHY timers will
need synchronization to ensure there is no overlap with a Tx timestamp.
The interrupt-based response complicates the locking somewhat. We can't use
a simple spinlock. This would require being acquired in
ice_ptp_req_tx_single_tstamp, and released in
ice_ptp_complete_tx_single_tstamp. The ice_ptp_req_tx_single_tstamp
function is called from the threaded IRQ, and the
ice_ptp_complete_tx_single_stamp is called from the low latency IRQ, so we
would need to acquire the lock with IRQs disabled.
To handle this, we'll use a wait queue along with
wait_event_interruptible_locked_irq in the update flows which don't use the
interrupt.
The interrupt flow will acquire the wait queue lock, set the
ATQBAL_FLAGS_INTR_IN_PROGRESS, and then initiate the firmware low latency
request, and unlock the wait queue lock.
Upon receipt of the low latency interrupt, the lock will be acquired, the
ATQBAL_FLAGS_INTR_IN_PROGRESS bit will be cleared, and the firmware
response will be captured, and wake_up_locked() will be called on the wait
queue.
The other flows will use wait_event_interruptible_locked_irq() to wait
until the ATQBAL_FLAGS_INTR_IN_PROGRESS is clear. This function checks the
condition under lock, but does not hold the lock while waiting. On return,
the lock is held, and a return of zero indicates we hold the lock and the
in-progress flag is not set.
This will ensure that threads which need to use the low latency interface
will sleep until they can acquire the lock without any pending low latency
interrupt flow interfering.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The TS_LL_READ macros are used as part of the low latency Tx timestamp
interface. A future firmware extension will add support for performing PHY
timer updates over this interface. Using TS_LL_READ as the prefix for these
macros will be confusing once the interface is used for other purposes.
Rename the macros, using the prefix REG_LL_PROXY_H, to better clarify that
this is for the low latency interface.
Additionally add macros for PF_SB_ATQBAH and PF_SB_ATQBAL registers to
better clarify content of this registers as PF_SB_ATQBAH contain low
part of Tx timestamp
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
