summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2025-03-18net: phy: phy_caps: Allow looking-up link caps based on speed and duplexMaxime Chevallier
As the link_caps array is efficient for <speed,duplex> lookups, implement a function for speed/duplex lookups that matches a given mask. This replicates to some extent the phy_lookup_settings() behaviour, matching full link_capabilities instead of a single linkmode. phy.c's phy_santize_settings() and phylink's phylink_ethtool_ksettings_set() performs such lookup using the phy_settings table, but are only interested in the actual speed/duplex that were matched, rathet than the individual linkmode. Similar to phy_lookup_settings(), the newly introduced phy_caps_lookup() will run through the link_caps[] array by descending speed/duplex order. If the link_capabilities for a given <speed/duplex> tuple intersects the passed linkmodes, we consider that a match. Similar to phy_lookup_settings(), we also allow passing an 'exact' boolean, allowing non-exact match. Here, we MUST always match the linkmodes mask, but we allow matching on lower speed settings. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250307173611.129125-8-maxime.chevallier@bootlin.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-18net: phy: phy_caps: Implement link_capabilities lookup by linkmodeMaxime Chevallier
In several occasions, phylib needs to lookup a set of matching speed and duplex against a given linkmode set. Instead of relying on the phy_settings array and thus iterate over the whole linkmodes list, use the link_capabilities array to lookup these matches, as we aren't interested in the actual link setting that matches but rather the speed and duplex for that setting. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250307173611.129125-7-maxime.chevallier@bootlin.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-18net: phy: phy_caps: Introduce phy_caps_validMaxime Chevallier
With the link_capabilities array, it's trivial to validate a given mask againts a <speed, duplex> tuple. Create a helper for that purpose, and use it to replace a phy_settings lookup in phy_check_valid(); Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250307173611.129125-6-maxime.chevallier@bootlin.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-18net: phy: phy_caps: Move __set_linkmode_max_speed to phy_capsMaxime Chevallier
Convert the __set_linkmode_max_speed to use the link_capabilities array. This makes it easy to clamp the linkmodes to a given max speed. Introduce a new helper phy_caps_linkmode_max_speed to replace the previous one that used phy_settings. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250307173611.129125-5-maxime.chevallier@bootlin.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-18net: phy: phy_caps: Move phy_speeds to phy_capsMaxime Chevallier
Use the newly introduced link_capabilities array to derive the list of possible speeds when given a combination of linkmodes. As link_capabilities is indexed by speed, we don't have to iterate the whole phy_settings array. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250307173611.129125-4-maxime.chevallier@bootlin.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-18net: phy: Use an internal, searchable storage for the linkmodesMaxime Chevallier
The canonical definition for all the link modes is in linux/ethtool.h, which is complemented by the link_mode_params array stored in net/ethtool/common.h . That array contains all the metadata about each of these modes, including the Speed and Duplex information. Phylib and phylink needs that information as well for internal management of the link, which was done by duplicating that information in locally-stored arrays and lookup functions. This makes it easy for developpers adding new modes to forget modifying phylib and phylink accordingly. However, the link_mode_params array in net/ethtool/common.c is fairly inefficient to search through, as it isn't sorted in any manner. Phylib and phylink perform a lot of lookup operations, mostly to filter modes by speed and/or duplex. We therefore introduce the link_caps private array in phy_caps.c, that indexes linkmodes in a more efficient manner. Each element associated a tuple <speed, duplex> to a bitfield of all the linkmodes runs at these speed/duplex. We end-up with an array that's fairly short, easily addressable and that it optimised for the typical use-cases of phylib/phylink. That array is initialized at the same time as phylib. As the link_mode_params array is part of the net stack, which phylink depends on, it should always be accessible from phylib. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250307173611.129125-3-maxime.chevallier@bootlin.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-18net: ethtool: Export the link_mode_params definitionsMaxime Chevallier
link_mode_params contains a lookup table of all 802.3 link modes that are currently supported with structured data about each mode's speed, duplex, number of lanes and mediums. As a preparation for a port representation, export that table for the rest of the net stack to use. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250307173611.129125-2-maxime.chevallier@bootlin.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17Merge branch ↵Paolo Abeni
'net-stmmac-avoid-unnecessary-work-in-stmmac_release-stmmac_dvr_remove' Russell King says: ==================== net: stmmac: avoid unnecessary work in stmmac_release()/stmmac_dvr_remove() This small series is a subset of a RFC I sent earlier. These two patches remove code that is unnecessary and/or wrong in these paths. Details in each commit. ==================== Link: https://patch.msgid.link/Z87bpDd7QYYVU0ML@shell.armlinux.org.uk Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17net: stmmac: remove unnecessary stmmac_mac_set() in stmmac_release()Russell King (Oracle)
stmmac_release() calls phylink_stop() and then goes on to call stmmac_mac_set(, false). However, phylink_stop() will call stmmac_mac_link_down() before returning, which will do this work. Remove this unnecessary call. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Furong Xu <0x1207@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1trcI6-005rn8-GV@rmk-PC.armlinux.org.uk Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17net: stmmac: remove redundant racy tear-down in stmmac_dvr_remove()Russell King (Oracle)
While the network device is registered, it is published to userspace, and thus userspace can change its state. This means calling functions such as stmmac_stop_all_dma() and stmmac_mac_set() are racy. Moreover, unregister_netdev() will unpublish the network device, and then if appropriate call the .ndo_stop() method, which is stmmac_release(). This will first call phylink_stop() which will synchronously take the link down, resulting in stmmac_mac_link_down() and stmmac_mac_set(, false) being called. stmmac_release() will also call stmmac_stop_all_dma(). Consequently, neither of these two functions need to called prior to unregister_netdev() as that will safely call paths that will result in this work being done if necessary. Remove these redundant racy calls. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Furong Xu <0x1207@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1trcI1-005rn2-CZ@rmk-PC.armlinux.org.uk Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17net: phylink: expand on .pcs_config() method documentationRussell King (Oracle)
Expand on the requirements of the .pcs_config() method documentation, specifically mentioning that it should cause minimal disruption to an established link, and that it should return a positive non-zero value when requiring the .pcs_an_restart() method to be called. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1trb24-005oVq-Is@rmk-PC.armlinux.org.uk Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17cdc_ether|r8152: ThinkPad Hybrid USB-C/A Dock quirkPhilipp Hahn
Lenovo ThinkPad Hybrid USB-C with USB-A Dock (17ef:a359) is affected by the same problem as the Lenovo Powered USB-C Travel Hub (17ef:721e): Both are based on the Realtek RTL8153B chip used to use the cdc_ether driver. However, using this driver, with the system suspended the device constantly sends pause-frames as soon as the receive buffer fills up. This causes issues with other devices, where some Ethernet switches stop forwarding packets altogether. Using the Realtek driver (r8152) fixes this issue. Pause frames are no longer sent while the host system is suspended. Cc: Leon Schuermann <leon@is.currently.online> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Oliver Neukum <oliver@neukum.org> (maintainer:USB CDC ETHERNET DRIVER) Cc: netdev@vger.kernel.org (open list:NETWORKING DRIVERS) Link: https://git.kernel.org/netdev/net/c/cb82a54904a9 Link: https://git.kernel.org/netdev/net/c/2284bbd0cf39 Link: https://www.lenovo.com/de/de/p/accessories-and-software/docking/docking-usb-docks/40af0135eu Signed-off-by: Philipp Hahn <phahn-oss@avm.de> Reviewed-by: Kory Maincent <kory.maincent@bootlin.com> Link: https://patch.msgid.link/484336aad52d14ccf061b535bc19ef6396ef5120.1741601523.git.p.hahn@avm.de Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17stmmac: intel: Fix warning message for return value in ↵Choong Yong Liang
intel_tsn_lane_is_available() Fix the warning "warn: missing error code? 'ret'" in the intel_tsn_lane_is_available() function. The function now returns 0 to indicate that a TSN lane was found and returns -EINVAL when it is not found. Fixes: a42f6b3f1cc1 ("net: stmmac: configure SerDes according to the interface mode") Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Reviewed-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250310050835.808870-1-yong.liang.choong@linux.intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17Merge branch 'net-phy-clean-up-phy-package-mmd-access-functions'Paolo Abeni
Heiner Kallweit says: ==================== net: phy: clean up PHY package MMD access functions Move declarations of the functions with users to phylib.h, and remove unused functions. ==================== Link: https://patch.msgid.link/b624fcb7-b493-461a-a0b5-9ca7e9d767bc@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17net: phy: remove unused functions phy_package_[read|write]_mmdHeiner Kallweit
These functions have never had a user, so remove them. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/5792e2cd-6f0a-4f7d-a5ef-b932f94d82f3@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17net: phy: move PHY package MMD access function declarations from phy.h to ↵Heiner Kallweit
phylib.h These functions are used by PHY drivers only, therefore move their declaration to phylib.h. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/406c8a20-b62e-4ee3-b174-b566724a0876@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17Merge branch 'mlx5-support-hws-flow-meter-sampler-actions-in-fs-core'Paolo Abeni
Tariq Toukan says: ==================== mlx5: Support HWS flow meter/sampler actions in FS core This series by Moshe adds support for flow meter and flow sampler HW Steering actions in FS core level. As these actions can be shared by multiple rules, these patches use refcounts to manage the HWS actions sharing in FS core level. ==================== Link: https://patch.msgid.link/1741543663-22123-1-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17net/mlx5: fs, add support for dest flow sampler HWS actionMoshe Shemesh
Add support for HW Steering action of flow sampler destination. For each flow sampler created cache the hws action by sampler id as a key. Hold refcount for each rule using the cached action. Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/1741543663-22123-4-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17net/mlx5: fs, add support for flow meters HWS actionMoshe Shemesh
Add support for HW Steering action of flow meter range. Flow meters range can use one HWS action for the whole range. Thus, share a cached HWS action among rules that use same flow meter object range. Hold refcount for each rule using the cached action. Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/1741543663-22123-3-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17net/mlx5: fs, add API for sharing HWS action by refcountMoshe Shemesh
Counters HWS actions are shared using refcount, to create action on demand by flow steering rule and destroy only when no rules are using the action. The method is extensible to other HWS action types, such as flow meter and sampler actions, in the downstream patches. Add an API to facilitate the reuse of get/put logic for HWS actions shared by refcount. Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/1741543663-22123-2-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-17Merge branch 'tcp-accecn'David S. Miller
Chia-Yu Chang says: ==================== AccECN protocol preparation patch series Please find the v7 v7 (03-Mar-2025) - Move 2 new patches added in v6 to the next AccECN patch series v6 (27-Dec-2024) - Avoid removing removing the potential CA_ACK_WIN_UPDATE in ack_ev_flags of patch #1 (Eric Dumazet <edumazet@google.com>) - Add reviewed-by tag in patches #2, #3, #4, #5, #6, #7, #8, #12, #14 - Foloiwng 2 new pathces are added after patch #9 (Patch that adds SKB_GSO_TCP_ACCECN) * New patch #10 to replace exisiting SKB_GSO_TCP_ECN with SKB_GSO_TCP_ACCECN in the driver to avoid CWR flag corruption * New patch #11 adds AccECN for virtio by adding new negotiation flag (VIRTIO_NET_F_HOST/GUEST_ACCECN) in feature handshake and translating Accurate ECN GSO flag between virtio_net_hdr (VIRTIO_NET_HDR_GSO_ACCECN) and skb header (SKB_GSO_TCP_ACCECN) - Add detailed changelog and comments in #13 (Eric Dumazet <edumazet@google.com>) - Move patch #14 to the next AccECN patch series (Eric Dumazet <edumazet@google.com>) v5 (5-Nov-2024) - Add helper function "tcp_flags_ntohs" to preserve last 2 bytes of TCP flags of patch #4 (Paolo Abeni <pabeni@redhat.com>) - Fix reverse X-max tree order of patches #4, #11 (Paolo Abeni <pabeni@redhat.com>) - Rename variable "delta" as "timestamp_delta" of patch #2 fo clariety - Remove patch #14 in this series (Paolo Abeni <pabeni@redhat.com>, Joel Granados <joel.granados@kernel.org>) v4 (21-Oct-2024) - Fix line length warning of patches #2, #4, #8, #10, #11, #14 - Fix spaces preferred around '|' (ctx:VxV) warning of patch #7 - Add missing CC'ed of patches #4, #12, #14 v3 (19-Oct-2024) - Fix build error in v2 v2 (18-Oct-2024) - Fix warning caused by NETIF_F_GSO_ACCECN_BIT in patch #9 (Jakub Kicinski <kuba@kernel.org>) The full patch series can be found in https://github.com/L4STeam/linux-net-next/commits/upstream_l4steam/ The Accurate ECN draft can be found in https://datatracker.ietf.org/doc/html/draft-ietf-tcpm-accurate-ecn-28 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: Pass flags to __tcp_send_ackIlpo Järvinen
Accurate ECN needs to send custom flags to handle IP-ECN field reflection during handshake. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: add new TCP_TW_ACK_OOW state and allow ECN bits in TOSIlpo Järvinen
ECN bits in TOS are always cleared when sending in ACKs in TW. Clearing them is problematic for TCP flows that used Accurate ECN because ECN bits decide which service queue the packet is placed into (L4S vs Classic). Effectively, TW ACKs are always downgraded from L4S to Classic queue which might impact, e.g., delay the ACK will experience on the path compared with the other packets of the flow. Change the TW ACK sending code to differentiate: - In tcp_v4_send_reset(), commit ba9e04a7ddf4f ("ip: fix tos reflection in ack and reset packets") cleans ECN bits for TW reset and this is not affected. - In tcp_v4_timewait_ack(), ECN bits for all TW ACKs are cleaned. But now only ECN bits of ACKs for oow data or paws_reject are cleaned, and ECN bits of other ACKs will not be cleaned. - In tcp_v4_reqsk_send_ack(), commit 66b13d99d96a1 ("ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT") did not clean ECN bits of ACKs for oow data or paws_reject. But now the ECN bits rae cleaned for these ACKs. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: AccECN support to tcp_add_backlogIlpo Järvinen
AE flag needs to be preserved for AccECN. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17gro: prevent ACE field corruption & better AccECN handlingIlpo Järvinen
There are important differences in how the CWR field behaves in RFC3168 and AccECN. With AccECN, CWR flag is part of the ACE counter and its changes are important so adjust the flags changed mask accordingly. Also, if CWR is there, set the Accurate ECN GSO flag to avoid corrupting CWR flag somewhere. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17gso: AccECN supportIlpo Järvinen
Handling the CWR flag differs between RFC 3168 ECN and AccECN. With RFC 3168 ECN aware TSO (NETIF_F_TSO_ECN) CWR flag is cleared starting from 2nd segment which is incompatible how AccECN handles the CWR flag. Such super-segments are indicated by SKB_GSO_TCP_ECN. With AccECN, CWR flag (or more accurately, the ACE field that also includes ECE & AE flags) changes only when new packet(s) with CE mark arrives so the flag should not be changed within a super-skb. The new skb/feature flags are necessary to prevent such TSO engines corrupting AccECN ACE counters by clearing the CWR flag (if the CWR handling feature cannot be turned off). If NIC is completely unaware of RFC3168 ECN (doesn't support NETIF_F_TSO_ECN) or its TSO engine can be set to not touch CWR flag despite supporting also NETIF_F_TSO_ECN, TSO could be safely used with AccECN on such NIC. This should be evaluated per NIC basis (not done in this patch series for any NICs). For the cases, where TSO cannot keep its hands off the CWR flag, a GSO fallback is provided by this patch. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: helpers for ECN mode handlingIlpo Järvinen
Create helpers for TCP ECN modes. No functional changes. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: rework {__,}tcp_ecn_check_ce() -> tcp_data_ecn_check()Ilpo Järvinen
Rename tcp_ecn_check_ce to tcp_data_ecn_check as it is called only for data segments, not for ACKs (with AccECN, also ACKs may get ECN bits). The extra "layer" in tcp_ecn_check_ce() function just checks for ECN being enabled, that can be moved into tcp_ecn_field_check rather than having the __ variant. No functional changes. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: extend TCP flags to allow AE bit/ACE fieldIlpo Järvinen
With AccECN, there's one additional TCP flag to be used (AE) and ACE field that overloads the definition of AE, CWR, and ECE flags. As tcp_flags was previously only 1 byte, the byte-order stuff needs to be added to it's handling. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: use BIT() macro in include/net/tcp.hChia-Yu Chang
Use BIT() macro for TCP flags field and TCP congestion control flags that will be used by the congestion control algorithm. No functional changes. Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Ilpo Järvinen <ij@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: create FLAG_TS_PROGRESSIlpo Järvinen
Whenever timestamp advances, it declares progress which can be used by the other parts of the stack to decide that the ACK is the most recent one seen so far. AccECN will use this flag when deciding whether to use the ACK to update AccECN state or not. Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-17tcp: reorganize tcp_in_ack_event() and tcp_count_delivered()Ilpo Järvinen
- Move tcp_count_delivered() earlier and split tcp_count_delivered_ce() out of it - Move tcp_in_ack_event() later - While at it, remove the inline from tcp_in_ack_event() and let the compiler to decide Accurate ECN's heuristics does not know if there is going to be ACE field based CE counter increase or not until after rtx queue has been processed. Only then the number of ACKed bytes/pkts is available. As CE or not affects presence of FLAG_ECE, that information for tcp_in_ack_event is not yet available in the old location of the call to tcp_in_ack_event(). Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-14net/smc: use the correct ndev to find pnetid by pnetid tableGuangguan Wang
When using smc_pnet in SMC, it will only search the pnetid in the base_ndev of the netdev hierarchy(both HW PNETID and User-defined sw pnetid). This may not work for some scenarios when using SMC in container on cloud environment. In container, there have choices of different container network, such as directly using host network, virtual network IPVLAN, veth, etc. Different choices of container network have different netdev hierarchy. Examples of netdev hierarchy show below. (eth0 and eth1 in host below is the netdev directly related to the physical device). _______________________________ | _________________ | | |POD | | | | | | | | eth0_________ | | | |____| |__| | | | | | | | | | | eth1|base_ndev| eth0_______ | | | | | RDMA || | host |_________| |_______|| --------------------------------- netdev hierarchy if directly using host network ________________________________ | _________________ | | |POD __________ | | | | |upper_ndev| | | | |eth0|__________| | | | |_______|_________| | | |lower netdev | | __|______ | | eth1| | eth0_______ | | |base_ndev| | RDMA || | host |_________| |_______|| --------------------------------- netdev hierarchy if using IPVLAN _______________________________ | _____________________ | | |POD _________ | | | | |base_ndev|| | | |eth0(veth)|_________|| | | |____________|________| | | |pairs | | _______|_ | | | | eth0_______ | | veth|base_ndev| | RDMA || | |_________| |_______|| | _________ | | eth1|base_ndev| | | host |_________| | --------------------------------- netdev hierarchy if using veth Due to some reasons, the eth1 in host is not RDMA attached netdevice, pnetid is needed to map the eth1(in host) with RDMA device so that POD can do SMC-R. Because the eth1(in host) is managed by CNI plugin(such as Terway, network management plugin in container environment), and in cloud environment the eth(in host) can dynamically be inserted by CNI when POD create and dynamically be removed by CNI when POD destroy and no POD related to the eth(in host) anymore. It is hard to config the pnetid to the eth1(in host). But it is easy to config the pnetid to the netdevice which can be seen in POD. When do SMC-R, both the container directly using host network and the container using veth network can successfully match the RDMA device, because the configured pnetid netdev is a base_ndev. But the container using IPVLAN can not successfully match the RDMA device and 0x03030000 fallback happens, because the configured pnetid netdev is not a base_ndev. Additionally, if config pnetid to the eth1(in host) also can not work for matching RDMA device when using veth network and doing SMC-R in POD. To resolve the problems list above, this patch extends to search user -defined sw pnetid in the clc handshake ndev when no pnetid can be found in the base_ndev, and the base_ndev take precedence over ndev for backward compatibility. This patch also can unify the pnetid setup of different network choices list above in container(Config user-defined sw pnetid in the netdevice can be seen in POD). Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Reviewed-by: Halil Pasic <pasic@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-03-14can: add protocol counter for AF_CAN socketsDavide Caratti
The third column in the output of the following command: | # grep CAN /proc/net/protocols is systematically '0': use sock_prot_inuse_add() to account for the number of sockets for each protocol on top of AF_CAN family. Signed-off-by: Davide Caratti <dcaratti@redhat.com> Link: https://patch.msgid.link/9db5d0e6c11b232ad895885616f1258882a32f61.1741952160.git.dcaratti@redhat.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2025-03-14selftests: drv-net: fix merge conflicts resolutionMatthieu Baerts (NGI0)
After the recent merge between net-next and net, I got some conflicts on my side because the merge resolution was different from Stephen's one [1] I applied on my side in the MPTCP tree. It looks like the code that is now in net-next is using the old way to retrieve the local and remote addresses. This patch is now using the new way, like what was in Stephen's email [1]. Also, in get_interface_info(), there were no conflicts in this area, because that was new code from 'net', but a small adaptation was needed there as well to get the remote address. Fixes: 941defcea7e1 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net") Link: https://lore.kernel.org/20250311115758.17a1d414@canb.auug.org.au [1] Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250314-net-next-drv-net-ping-fix-merge-v1-1-0d5c19daf707@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-14dt-bindings: can: fsl,flexcan: add i.MX94 supportFrank Li
Add compatible string "fsl,imx94-flexcan" for the i.MX94 chip, which is backward compatible with i.MX95. Set it to fall back to "fsl,imx95-flexcan". Acked-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://patch.msgid.link/20250307190816.2971810-1-Frank.Li@nxp.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2025-03-14Merge patch series "can: flexcan: add transceiver capabilities"Marc Kleine-Budde
Dimitri Fedrau <dimitri.fedrau@liebherr.com> says: Currently the flexcan driver does only support adding PHYs by using the "old" regulator bindings. Add support for CAN transceivers as a PHY. Add the capability to ensure that the PHY is in operational state when the link is set to an "up" state. Changes in v4: - Dropped "if: required: phys" in bindings - Link to v3: https://lore.kernel.org/r/20250221-flexcan-add-transceiver-caps-v3-0-a947bde55a62@liebherr.com Changes in v3: - Have xceiver-supply or phys properties in bindings - Switch do dev_err_probe in flexcan_probe when checking error of call devm_phy_optional_get - Link to v2: https://lore.kernel.org/r/20250220-flexcan-add-transceiver-caps-v2-0-a81970f11846@liebherr.com Changes in v2: - Rename variable xceiver to transceiver in struct flexcan_priv and in flexcan_probe - Set priv->can.bitrate_max if transceiver is found - Fix commit messages which claim that transceivers are not supported - Do not print error on EPROBE_DEFER after calling devm_phy_optional_get in flexcan_probe - Link to v1: https://lore.kernel.org/r/20250211-flexcan-add-transceiver-caps-v1-0-c6abb7817b0f@liebherr.com Link: https://patch.msgid.link/20250312-flexcan-add-transceiver-caps-v4-0-29e89ae0225a@liebherr.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2025-03-14can: flexcan: add transceiver capabilitiesDimitri Fedrau
Currently the flexcan driver does only support adding PHYs by using the "old" regulator bindings. Add support for CAN transceivers as a PHY. Add the capability to ensure that the PHY is in operational state when the link is set to an "up" state. Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com> Link: https://patch.msgid.link/20250312-flexcan-add-transceiver-caps-v4-2-29e89ae0225a@liebherr.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2025-03-14dt-bindings: can: fsl,flexcan: add transceiver capabilitiesDimitri Fedrau
Currently the flexcan driver does only support adding PHYs by using the "old" regulator bindings. Add support for CAN transceivers as a PHY. Acked-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com> Link: https://patch.msgid.link/20250312-flexcan-add-transceiver-caps-v4-1-29e89ae0225a@liebherr.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2025-03-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netPaolo Abeni
Cross-merge networking fixes after downstream PR (net-6.14-rc6). Conflicts: tools/testing/selftests/drivers/net/ping.py 75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py") de94e8697405 ("selftests: drv-net: store addresses in dict indexed by ipver") https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/ net/core/devmem.c a70f891e0fa0 ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()") 1d22d3060b9b ("net: drop rtnl_lock for queue_mgmt operations") https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/ Adjacent changes: tools/testing/selftests/net/Makefile 6f50175ccad4 ("selftests: Add IPv6 link-local address generation tests for GRE devices.") 2e5584e0f913 ("selftests/net: expand cmsg_ipv6.sh with ipv4") drivers/net/ethernet/broadcom/bnxt/bnxt.c 661958552eda ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic") fe96d717d38e ("bnxt_en: Extend queue stop/start for TX rings") Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-13Merge tag 'net-6.14-rc7' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Including fixes from netfilter, bluetooth and wireless. No known regressions outstanding. Current release - regressions: - wifi: nl80211: fix assoc link handling - eth: lan78xx: sanitize return values of register read/write functions Current release - new code bugs: - ethtool: tsinfo: fix dump command - bluetooth: btusb: configure altsetting for HCI_USER_CHANNEL - eth: mlx5: DR, use the right action structs for STEv3 Previous releases - regressions: - netfilter: nf_tables: make destruction work queue pernet - gre: fix IPv6 link-local address generation. - wifi: iwlwifi: fix TSO preparation - bluetooth: revert "bluetooth: hci_core: fix sleeping function called from invalid context" - ovs: revert "openvswitch: switch to per-action label counting in conntrack" - eth: - ice: fix switchdev slow-path in LAG - bonding: fix incorrect MAC address setting to receive NS messages Previous releases - always broken: - core: prevent TX of unreadable skbs - sched: prevent creation of classes with TC_H_ROOT - netfilter: nft_exthdr: fix offset with ipv4_find_option() - wifi: cfg80211: cancel wiphy_work before freeing wiphy - mctp: copy headers if cloned - phy: nxp-c45-tja11xx: add errata for TJA112XA/B - eth: - bnxt: fix kernel panic in the bnxt_get_queue_stats{rx | tx} - mlx5: bridge, fix the crash caused by LAG state check" * tag 'net-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits) net: mana: cleanup mana struct after debugfs_remove() net/mlx5e: Prevent bridge link show failure for non-eswitch-allowed devices net/mlx5: Bridge, fix the crash caused by LAG state check net/mlx5: Lag, Check shared fdb before creating MultiPort E-Switch net/mlx5: Fix incorrect IRQ pool usage when releasing IRQs net/mlx5: HWS, Rightsize bwc matcher priority net/mlx5: DR, use the right action structs for STEv3 Revert "openvswitch: switch to per-action label counting in conntrack" net: openvswitch: remove misbehaving actions length check selftests: Add IPv6 link-local address generation tests for GRE devices. gre: Fix IPv6 link-local address generation. netfilter: nft_exthdr: fix offset with ipv4_find_option() selftests/tc-testing: Add a test case for DRR class with TC_H_ROOT net_sched: Prevent creation of classes with TC_H_ROOT ipvs: prevent integer overflow in do_ip_vs_get_ctl() selftests: netfilter: skip br_netfilter queue tests if kernel is tainted netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in insert_tree() wifi: mac80211: fix MPDU length parsing for EHT 5/6 GHz qlcnic: fix memory leak issues in qlcnic_sriov_common.c rtase: Fix improper release of ring list entries in rtase_sw_reset ...
2025-03-13Merge tag 'vfs-6.14-rc7.fixes' of ↵Linus Torvalds
gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs Pull vfs fixes from Christian Brauner: - Bring in an RCU pathwalk fix for afs. This is brought in as a merge from the vfs-6.15.shared.afs branch that needs this commit and other trees already depend on it. - Fix vboxfs unterminated string handling. * tag 'vfs-6.14-rc7.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs: vboxsf: Add __nonstring annotations for unterminated strings afs: Fix afs_atcell_get_link() to handle RCU pathwalk
2025-03-13Merge tag 'nf-25-03-13' of ↵Paolo Abeni
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf Pablo Neira Ayuso says: ==================== Netfilter/IPVS fixes for net The following patchset contains Netfilter/IPVS fixes for net: 1) Missing initialization of cpu and jiffies32 fields in conncount, from Kohei Enju. 2) Skip several tests in case kernel is tainted, otherwise tests bogusly report failure too as they also check for tainted kernel, from Florian Westphal. 3) Fix a hyphothetical integer overflow in do_ip_vs_get_ctl() leading to bogus error logs, from Dan Carpenter. 4) Fix incorrect offset in ipv4 option match in nft_exthdr, from Alexey Kashavkin. netfilter pull request 25-03-13 * tag 'nf-25-03-13' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf: netfilter: nft_exthdr: fix offset with ipv4_find_option() ipvs: prevent integer overflow in do_ip_vs_get_ctl() selftests: netfilter: skip br_netfilter queue tests if kernel is tainted netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in insert_tree() ==================== Link: https://patch.msgid.link/20250313095636.2186-1-pablo@netfilter.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-13net: mana: cleanup mana struct after debugfs_remove()Shradha Gupta
When on a MANA VM hibernation is triggered, as part of hibernate_snapshot(), mana_gd_suspend() and mana_gd_resume() are called. If during this mana_gd_resume(), a failure occurs with HWC creation, mana_port_debugfs pointer does not get reinitialized and ends up pointing to older, cleaned-up dentry. Further in the hibernation path, as part of power_down(), mana_gd_shutdown() is triggered. This call, unaware of the failures in resume, tries to cleanup the already cleaned up mana_port_debugfs value and hits the following bug: [ 191.359296] mana 7870:00:00.0: Shutdown was called [ 191.359918] BUG: kernel NULL pointer dereference, address: 0000000000000098 [ 191.360584] #PF: supervisor write access in kernel mode [ 191.361125] #PF: error_code(0x0002) - not-present page [ 191.361727] PGD 1080ea067 P4D 0 [ 191.362172] Oops: Oops: 0002 [#1] SMP NOPTI [ 191.362606] CPU: 11 UID: 0 PID: 1674 Comm: bash Not tainted 6.14.0-rc5+ #2 [ 191.363292] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 11/21/2024 [ 191.364124] RIP: 0010:down_write+0x19/0x50 [ 191.364537] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 55 48 89 e5 53 48 89 fb e8 de cd ff ff 31 c0 ba 01 00 00 00 <f0> 48 0f b1 13 75 16 65 48 8b 05 88 24 4c 6a 48 89 43 08 48 8b 5d [ 191.365867] RSP: 0000:ff45fbe0c1c037b8 EFLAGS: 00010246 [ 191.366350] RAX: 0000000000000000 RBX: 0000000000000098 RCX: ffffff8100000000 [ 191.366951] RDX: 0000000000000001 RSI: 0000000000000064 RDI: 0000000000000098 [ 191.367600] RBP: ff45fbe0c1c037c0 R08: 0000000000000000 R09: 0000000000000001 [ 191.368225] R10: ff45fbe0d2b01000 R11: 0000000000000008 R12: 0000000000000000 [ 191.368874] R13: 000000000000000b R14: ff43dc27509d67c0 R15: 0000000000000020 [ 191.369549] FS: 00007dbc5001e740(0000) GS:ff43dc663f380000(0000) knlGS:0000000000000000 [ 191.370213] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 191.370830] CR2: 0000000000000098 CR3: 0000000168e8e002 CR4: 0000000000b73ef0 [ 191.371557] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 191.372192] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 [ 191.372906] Call Trace: [ 191.373262] <TASK> [ 191.373621] ? show_regs+0x64/0x70 [ 191.374040] ? __die+0x24/0x70 [ 191.374468] ? page_fault_oops+0x290/0x5b0 [ 191.374875] ? do_user_addr_fault+0x448/0x800 [ 191.375357] ? exc_page_fault+0x7a/0x160 [ 191.375971] ? asm_exc_page_fault+0x27/0x30 [ 191.376416] ? down_write+0x19/0x50 [ 191.376832] ? down_write+0x12/0x50 [ 191.377232] simple_recursive_removal+0x4a/0x2a0 [ 191.377679] ? __pfx_remove_one+0x10/0x10 [ 191.378088] debugfs_remove+0x44/0x70 [ 191.378530] mana_detach+0x17c/0x4f0 [ 191.378950] ? __flush_work+0x1e2/0x3b0 [ 191.379362] ? __cond_resched+0x1a/0x50 [ 191.379787] mana_remove+0xf2/0x1a0 [ 191.380193] mana_gd_shutdown+0x3b/0x70 [ 191.380642] pci_device_shutdown+0x3a/0x80 [ 191.381063] device_shutdown+0x13e/0x230 [ 191.381480] kernel_power_off+0x35/0x80 [ 191.381890] hibernate+0x3c6/0x470 [ 191.382312] state_store+0xcb/0xd0 [ 191.382734] kobj_attr_store+0x12/0x30 [ 191.383211] sysfs_kf_write+0x3e/0x50 [ 191.383640] kernfs_fop_write_iter+0x140/0x1d0 [ 191.384106] vfs_write+0x271/0x440 [ 191.384521] ksys_write+0x72/0xf0 [ 191.384924] __x64_sys_write+0x19/0x20 [ 191.385313] x64_sys_call+0x2b0/0x20b0 [ 191.385736] do_syscall_64+0x79/0x150 [ 191.386146] ? __mod_memcg_lruvec_state+0xe7/0x240 [ 191.386676] ? __lruvec_stat_mod_folio+0x79/0xb0 [ 191.387124] ? __pfx_lru_add+0x10/0x10 [ 191.387515] ? queued_spin_unlock+0x9/0x10 [ 191.387937] ? do_anonymous_page+0x33c/0xa00 [ 191.388374] ? __handle_mm_fault+0xcf3/0x1210 [ 191.388805] ? __count_memcg_events+0xbe/0x180 [ 191.389235] ? handle_mm_fault+0xae/0x300 [ 191.389588] ? do_user_addr_fault+0x559/0x800 [ 191.390027] ? irqentry_exit_to_user_mode+0x43/0x230 [ 191.390525] ? irqentry_exit+0x1d/0x30 [ 191.390879] ? exc_page_fault+0x86/0x160 [ 191.391235] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 191.391745] RIP: 0033:0x7dbc4ff1c574 [ 191.392111] Code: c7 00 16 00 00 00 b8 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 80 3d d5 ea 0e 00 00 74 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 55 48 89 e5 48 83 ec 20 48 89 [ 191.393412] RSP: 002b:00007ffd95a23ab8 EFLAGS: 00000202 ORIG_RAX: 0000000000000001 [ 191.393990] RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007dbc4ff1c574 [ 191.394594] RDX: 0000000000000005 RSI: 00005a6eeadb0ce0 RDI: 0000000000000001 [ 191.395215] RBP: 00007ffd95a23ae0 R08: 00007dbc50003b20 R09: 0000000000000000 [ 191.395805] R10: 0000000000000001 R11: 0000000000000202 R12: 0000000000000005 [ 191.396404] R13: 00005a6eeadb0ce0 R14: 00007dbc500045c0 R15: 00007dbc50001ee0 [ 191.396987] </TASK> To fix this, we explicitly set such mana debugfs variables to NULL after debugfs_remove() is called. Fixes: 6607c17c6c5e ("net: mana: Enable debugfs files for MANA device") Cc: stable@vger.kernel.org Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Link: https://patch.msgid.link/1741688260-28922-1-git-send-email-shradhagupta@linux.microsoft.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-13Merge branch 'mlx5-misc-fixes-2025-03-10'Paolo Abeni
Tariq Toukan says: ==================== mlx5 misc fixes 2025-03-10 This patchset provides misc bug fixes from the team to the mlx5 core and Eth drivers. ==================== Link: https://patch.msgid.link/1741644104-97767-1-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-13net/mlx5e: Prevent bridge link show failure for non-eswitch-allowed devicesCarolina Jubran
mlx5_eswitch_get_vepa returns -EPERM if the device lacks eswitch_manager capability, blocking mlx5e_bridge_getlink from retrieving VEPA mode. Since mlx5e_bridge_getlink implements ndo_bridge_getlink, returning -EPERM causes bridge link show to fail instead of skipping devices without this capability. To avoid this, return -EOPNOTSUPP from mlx5e_bridge_getlink when mlx5_eswitch_get_vepa fails, ensuring the command continues processing other devices while ignoring those without the necessary capability. Fixes: 4b89251de024 ("net/mlx5: Support ndo bridge_setlink and getlink") Signed-off-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/1741644104-97767-7-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-13net/mlx5: Bridge, fix the crash caused by LAG state checkJianbo Liu
When removing LAG device from bridge, NETDEV_CHANGEUPPER event is triggered. Driver finds the lower devices (PFs) to flush all the offloaded entries. And mlx5_lag_is_shared_fdb is checked, it returns false if one of PF is unloaded. In such case, mlx5_esw_bridge_lag_rep_get() and its caller return NULL, instead of the alive PF, and the flush is skipped. Besides, the bridge fdb entry's lastuse is updated in mlx5 bridge event handler. But this SWITCHDEV_FDB_ADD_TO_BRIDGE event can be ignored in this case because the upper interface for bond is deleted, and the entry will never be aged because lastuse is never updated. To make things worse, as the entry is alive, mlx5 bridge workqueue keeps sending that event, which is then handled by kernel bridge notifier. It causes the following crash when accessing the passed bond netdev which is already destroyed. To fix this issue, remove such checks. LAG state is already checked in commit 15f8f168952f ("net/mlx5: Bridge, verify LAG state when adding bond to bridge"), driver still need to skip offload if LAG becomes invalid state after initialization. Oops: stack segment: 0000 [#1] SMP CPU: 3 UID: 0 PID: 23695 Comm: kworker/u40:3 Tainted: G OE 6.11.0_mlnx #1 Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5_bridge_wq mlx5_esw_bridge_update_work [mlx5_core] RIP: 0010:br_switchdev_event+0x2c/0x110 [bridge] Code: 44 00 00 48 8b 02 48 f7 00 00 02 00 00 74 69 41 54 55 53 48 83 ec 08 48 8b a8 08 01 00 00 48 85 ed 74 4a 48 83 fe 02 48 89 d3 <4c> 8b 65 00 74 23 76 49 48 83 fe 05 74 7e 48 83 fe 06 75 2f 0f b7 RSP: 0018:ffffc900092cfda0 EFLAGS: 00010297 RAX: ffff888123bfe000 RBX: ffffc900092cfe08 RCX: 00000000ffffffff RDX: ffffc900092cfe08 RSI: 0000000000000001 RDI: ffffffffa0c585f0 RBP: 6669746f6e690a30 R08: 0000000000000000 R09: ffff888123ae92c8 R10: 0000000000000000 R11: fefefefefefefeff R12: ffff888123ae9c60 R13: 0000000000000001 R14: ffffc900092cfe08 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f15914c8734 CR3: 0000000002830005 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __die_body+0x1a/0x60 ? die+0x38/0x60 ? do_trap+0x10b/0x120 ? do_error_trap+0x64/0xa0 ? exc_stack_segment+0x33/0x50 ? asm_exc_stack_segment+0x22/0x30 ? br_switchdev_event+0x2c/0x110 [bridge] ? sched_balance_newidle.isra.149+0x248/0x390 notifier_call_chain+0x4b/0xa0 atomic_notifier_call_chain+0x16/0x20 mlx5_esw_bridge_update+0xec/0x170 [mlx5_core] mlx5_esw_bridge_update_work+0x19/0x40 [mlx5_core] process_scheduled_works+0x81/0x390 worker_thread+0x106/0x250 ? bh_worker+0x110/0x110 kthread+0xb7/0xe0 ? kthread_park+0x80/0x80 ret_from_fork+0x2d/0x50 ? kthread_park+0x80/0x80 ret_from_fork_asm+0x11/0x20 </TASK> Fixes: ff9b7521468b ("net/mlx5: Bridge, support LAG") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Vlad Buslov <vladbu@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/1741644104-97767-6-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-13net/mlx5: Lag, Check shared fdb before creating MultiPort E-SwitchShay Drory
Currently, MultiPort E-Switch is requesting to create a LAG with shared FDB without checking the LAG is supporting shared FDB. Add the check. Fixes: a32327a3a02c ("net/mlx5: Lag, Control MultiPort E-Switch single FDB mode") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/1741644104-97767-5-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-13net/mlx5: Fix incorrect IRQ pool usage when releasing IRQsShay Drory
mlx5_irq_pool_get() is a getter for completion IRQ pool only. However, after the cited commit, mlx5_irq_pool_get() is called during ctrl IRQ release flow to retrieve the pool, resulting in the use of an incorrect IRQ pool. Hence, use the newly introduced mlx5_irq_get_pool() getter to retrieve the correct IRQ pool based on the IRQ itself. While at it, rename mlx5_irq_pool_get() to mlx5_irq_table_get_comp_irq_pool() which accurately reflects its purpose and improves code readability. Fixes: 0477d5168bbb ("net/mlx5: Expose SFs IRQs") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Maher Sanalla <msanalla@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/1741644104-97767-4-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-13net/mlx5: HWS, Rightsize bwc matcher priorityVlad Dogaru
The bwc layer was clamping the matcher priority from 32 bits to 16 bits. This didn't show up until a matcher was resized, since the initial native matcher was created using the correct 32 bit value. The fix also reorders fields to avoid some padding. Fixes: 2111bb970c78 ("net/mlx5: HWS, added backward-compatible API handling") Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com> Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1741644104-97767-3-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
generated by cgit (git 2.34.1) at 2025-07-16 19:46:05 +0000