summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-01-22i2c: omap: fix draining irq handlingAaro Koskinen
Commit 0bdfe0cb803dce699ff337c35d8e97ac355fa417 (i2c: omap: sanitize exit path) changed the interrupt handler to exit early and complete the transfer after the draining IRQ is handled. As a result, the ARDY may not be cleared properly, and it may cause all future I2C transfers to timeout with "timeout waiting for bus ready". This is reproducible at least with N900 when twl4030_gpio makes a long write (> FIFO size) during the probe (http://marc.info/?l=linux-omap&m=135818882610432&w=2). The fix is to continue until we get ARDY interrupt that completes the transfer. Tested with 3.8-rc4 + N900: 20 boots in a row without errors; without the patch the problem triggers after few reboots. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2013-01-22i2c: omap: errata i462: fix incorrect ack for arbitration lost interruptAaro Koskinen
The errata handling function acks wrong interrupt in case of "Arbitration lost". Fix it. Discovered during code review, the real impact of the bug is unknown. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2013-01-22ACPI: Check MSR valid bit before using P-state frequenciesStefan Bader
To fix incorrect P-state frequencies which can happen on some AMD systems f594065faf4f9067c2283a34619fc0714e79a98d "ACPI: Add fixups for AMD P-state figures" introduced a quirk to obtain the correct values by reading from AMD specific MSRs. This did cause a regression when running a kernel using that quirk under Xen which does (currently) not pass through MSR reads to the HW. Instead the guest gets a 0 in return. And this seems to cause a failure to initialize the ondemand governour (hard to say for sure as all P-states appear to run at the same frequency). While this should also be fixed in the hypervisor (to allow a guest to read that MSR), this patch is intended to work around the issue in the meantime. In discussion it turned out that indeed real HW/BIOSes may choose to not set the valid bit and thus mark the P-state as invalid. So this could be considered a fix for broken BIOSes that also works around the issue on Xen. Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Cc: 3.7+ <stable@vger.kernel.org> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-22PM / devfreq: exynos4_bus: honor RCU lock usageNishanth Menon
OPP pointers cannot be expected to be valid beyond the boundary of rcu_read_lock and rcu_read_unlock. Unfortunately, the current exynos4 busfreq driver does not honor the usage constraint and stores the OPP pointer in struct busfreq_data. This could potentially become invalid later such as: across devfreq opp change decisions, resulting in unpredictable behavior. To fix this, we introduce a busfreq specific busfreq_opp_info structure which is used to handle OPP information. OPP information is de-referenced to voltage and frequency pairs as needed into busfreq_opp_info structure and used as needed. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-22PM / devfreq: add locking documentation for recommended_oppNishanth Menon
OPP pointers are protected by RCU locks, the pointer validity is permissible only under the section of rcu_read_lock to rcu_read_unlock Add documentation to the effect. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-22cpufreq: cpufreq-cpu0: use RCU locks around usage of OPPNishanth Menon
OPP pointer is RCU protected, hence after finding it, de-reference also should be protected with the same RCU context else the OPP pointer may become invalid. Reported-by: Jack Mitchell <jack@embed.me.uk> Tested-by: Alexander Holler <holler@ahsoftware.de> Tested-by: Jack Mitchell <jack@embed.me.uk> Acked-by: Alexander Holler <holler@ahsoftware.de> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-22cpufreq: OMAP: use RCU locks around usage of OPPNishanth Menon
OPP pointer is RCU protected, hence after finding it, de-reference also should be protected with the same RCU context else the OPP pointer may become invalid. Reported-by: Alexander Holler <holler@ahsoftware.de> Tested-by: Alexander Holler <holler@ahsoftware.de> Acked-by: Alexander Holler <holler@ahsoftware.de> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-22i2c: muxes: fix wrong use of sizeof(ptr)Laurent Navet
sizeof when applied to a pointer typed expression gives the size of the pointer The semantic patch that makes this output is available in scripts/coccinelle/misc/noderef.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/ Signed-off-by: Laurent Navet <laurent.navet@gmail.com> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2013-01-22i2c: sirf: register i2c_client from dt child-nodes in probe entryBarry Song
in probe() entry of i2c_driver, set the of node of adapter and call of_i2c_register_devices to register all i2c_client from dt child-nodes Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2013-01-22i2c: mxs: Fix type of error codeFabio Estevam
cmd_err is used to handle error code, so it should not be unsigned. This fixes the following warning when building with W=1 option: drivers/i2c/busses/i2c-mxs.c: In function 'mxs_i2c_xfer_msg': drivers/i2c/busses/i2c-mxs.c:331:19: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: stable@kernel.org
2013-01-22regmap: fix small typo in regmap_bulk_write commentNestor Ovroy
Signed-off-by: Nestor Ovroy <novroy@riseup.net> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-22Merge tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6 into ↵Olof Johansson
fixes From Sascha Hauer: ARM i.MX fixes for -rc. This contains a single compilation fix for the CODA driver. * tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6: [media] coda: Fix build due to iram.h rename
2013-01-22mfd: arizona: Check errors from regcache_sync()Mark Brown
If the control bus is unrelabile we may hit errors during regcache_sync(), especially given that it tends to be one the most dense bursts of I/O in many systems. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-22mfd: tc3589x: Use simple irqdomainLinus Walleij
This fixes a regression in the TC3589x driver introduced in commit 15e27b1088245a2de3b7d09d39cd209212eb16af "mfd: Provide the tc3589x with its own IRQ domain" If a system with a TC3589x expander is booted and a base IRQ is passed from platform data, a legacy domain will be used. However, since the Ux500 is now switched to use SPARSE_IRQ, no descriptors get allocated on-the-fly, and we get a crash. Fix this by switching to using the simple irqdomain that will handle this uniformly and also allocates descriptors explicitly. Also fix two small whitespace errors in the vicinity while we're at it. Cc: stable@kernel.org Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-22mfd: pcf50633: Init pcf->dev before using itAxel Lin
Current code uses pcf->dev in the dev_err call before setting it to &client->dev. Fix it. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-22mfd: max77693: Init max77693->dev before using itAxel Lin
Current code uses max77693->dev in the dev_err call before setting it to &i2c->dev. Fix it. This patch also includes below cleanups: - Move checking pdata earlier and show dev_err if no platform data found. - Remove unnecessary err_regmap goto label. - Unregister i2c devices if regmap init for muic fails. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-22mfd: max77686: Init max77686->dev before using itAxel Lin
Current code uses max77686->dev in the dev_err call before setting it to &i2c->dev. Fix it. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-22f2fs: use _safe() version of list_for_eachDan Carpenter
This is calling list_del() inside a loop which is a problem when we try move to the next item on the list. I've converted it to use the _safe version. And also, as a cleanup, I've converted it to use list_for_each_entry instead of list_for_each. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-01-22f2fs: add comments of start_bidx_of_nodeJaegeuk Kim
The caller of start_bidx_of_node() should give proper node offsets which point only direct node blocks. Otherwise, it is a caller's bug. This patch adds comments to make it clear. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-01-22f2fs: avoid issuing small bios due to several dirty node pagesJaegeuk Kim
If some small bios of dirty node pages are supposed to be issued during the sequential data writes, there-in well-produced consecutive data bios are able to be split by the small node bios, resulting in performance degradation. So, let's collect a number of dirty node pages until reaching a threshold. And, by default, I set the threshold as 2MB, a segment size. This improves sequential write performance on i5, 512GB SSD (830 w/ SATA2) as follows. Before: 231 MB/s -> After: 255 MB/s Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com> Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
2013-01-22f2fs: support swapfileJaegeuk Kim
This patch adds f2fs_bmap operation to the data address space. This enables f2fs to support swapfile. Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-01-22f2fs: add remap_pages as generic_file_remap_pagesJaegeuk Kim
This was added for all the file systems before. See the following commit. commit id: 0b173bc4daa8f8ec03a85abf5e47b23502ff80af [PATCH] mm: kill vma flag VM_CAN_NONLINEAR This patch moves actual ptes filling for non-linear file mappings into special vma operation: ->remap_pages(). File system must implement this method to get non-linear mappings support, if it uses filemap_fault() then generic_file_remap_pages() can be used. Now device drivers can implement this method and obtain nonlinear vma support." Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-01-22f2fs: add __init to functions in init_f2fs_fsNamjae Jeon
Add __init to functions in init_f2fs_fs for code consistency. Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-01-21Btrfs: fix a regression in balance usage filterIlya Dryomov
Commit 3fed40cc ("Btrfs: cleanup duplicated division functions"), which was merged into 3.8-rc1, has introduced a regression by removing logic that was guarding us against bad user input. Bring it back. Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
2013-01-21Merge branch 'mutex-ops@next-for-chris' of ↵Chris Mason
git://github.com/idryomov/btrfs-unstable into linus
2013-01-21Merge branch 'for-chris' of ↵Chris Mason
git://git.kernel.org/pub/scm/linux/kernel/git/josef/btrfs-next into linus
2013-01-21Btrfs: prevent qgroup destroy when there are still relationsArne Jansen
Currently you can just destroy a qgroup even though it is in use by other qgroups or has qgroups assigned to it. This patch prevents destruction of qgroups unless they are completely unused. Otherwise destroy will return EBUSY. Reported-by: Eric Hopper <hopper@omnifarious.org> Signed-off-by: Arne Jansen <sensille@gmx.net> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
2013-01-21Btrfs: ignore orphan qgroup relationsArne Jansen
If a qgroup that has still assignments is deleted by the user, the corresponding relations are left in the tree. This leads to an unmountable filesystem. With this patch, those relations are simple ignored. Reported-by: Eric Hopper <hopper@omnifarious.org> Signed-off-by: Arne Jansen <sensille@gmx.net> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
2013-01-22mfd: db8500-prcmu: Fix irqdomain usageLinus Walleij
This fixes two issues with the DB8500 PRCMU irqdomain: - You have to state the irq base 0 to get a linear domain for the DT case from irq_domain_add_simple() - The irqdomain was not used to translate the initial irq request using irq_create_mapping() making the linear case fail as it was lacking a proper descriptor. I took this opportunity to fix two lines of whitespace errors in related code as I was anyway messing around with it. Cc: stable@kernel.org Acked-by Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-22mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build errorAnilKumar Ch
TPS65910 mfd driver uses functions that are only avaiable when REGMAP_IRQ is enabled. So "select REGMAP_IRQ" is added to mfd Kconfig to fix below build error: drivers/built-in.o: In function `tps65910_irq_exit': /media/anil/kernel/drivers/mfd/tps65910.c:265: undefined reference to `regmap_del_irq_chip' drivers/built-in.o: In function `tps65910_irq_init': /media/anil/kernel/drivers/mfd/tps65910.c:254: undefined reference to `regmap_add_irq_chip' drivers/built-in.o: In function `tps65910_i2c_probe': /media/anil/kernel/drivers/mfd/tps65910.c:509: undefined reference to `regmap_irq_get_domain' make: *** [vmlinux] Error 1 Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Tested-by: Matt Porter <mporter@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-22mfd: arizona: Disable control interface reporting for WM5102 and WM5110Mark Brown
Rather than disabling the error reporting only for earlier revisions unconditionally disable it. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-21isdn/gigaset: fix zero size border case in debug dumpTilman Schmidt
If subtracting 12 from l leaves zero we'd do a zero size allocation, leading to an oops later when we try to set the NUL terminator. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21Merge tag 'fixes-for-v3.8-rc5' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus Felipe writes: usb: fixes for v3.8-rc5 Finally we have a build fix for fsl-mxc-udc UDC driver. We also have a fix for ep0 maxburst setting on DWC3 which could confuse the HW if we tell it we had way too many streams on that endpoint when it _has_ to be only one. cppi_dma support for MUSB got a fix when running as a module. By dropping the wrong __init annotation, the function will be available even when we're modules and we're done with .init.text section. Last, but not least, we have a fix on FunctionFS which was causing a bug on our option parsing algorithm.
2013-01-21cdc_ncm: add support FLAG_NOARP for Infineon modem platformWei Shuai
Infineon(now Intel) HSPA Modem platform NCM cannot support ARP. we can define a new common structure wwan_noarp_info. Then more similiar NO ARP devices can be handled easily Signed-off-by: Wei Shuai <cpuwolf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21usbnet: add new flag FLAG_NOARP for usb net devicesWei Shuai
We do have some USB net devices, which cannot do ARP. so we can introduce a new flag FLAG_NOARP, then client drivers can easily handle this kind of devices Signed-off-by: Wei Shuai <cpuwolf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21Merge branch 'usb_cdc_fixes'David S. Miller
Bjørn Mork says: ==================== The 2 first patches in this series are required to make the Sierra Wireless MC7710 card work in MBIM mode. They may also be required for other Qualcomm firmware based MBIM devices. Patch #1 was previously posted as a standalone patch. This version is a replacement, removing a theoretical NULL pointer exception. Patch #3 fixes a bug I introduced in v3.7 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21net: cdc_ncm: fix error path for single interface probingBjørn Mork
commit bbc8d92 (net: cdc_ncm: add Huawei devices) implemented support for devices with a single combined control and data interface. Fix up the error path so that we do not double release such interfaces in case of probing failures. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21net: cdc_mbim: send ZLP after max sized NTBsBjørn Mork
We normally avoid sending ZLPs by padding NTBs with a zero byte if the NTB is shorter than dwNtbOutMaxSize, resulting in a short USB packet instead of a ZLP. But in the case where the NTB length is exactly dwNtbOutMaxSize and this is an exact multiplum of wMaxPacketSize, then we must send a ZLP. This fixes an issue seen on a Sierra Wireless MC7710 device where the transmission would fail whenever we ended up padding the NTBs to max size. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21net: cdc_ncm: workaround for missing CDC UnionBjørn Mork
Adding support for the MBIM mode in some Sierra Wireless devices. Some Sierra Wireless firmwares support CDC MBIM but have no CDC Union funtional descriptor. This violates the MBIM specification, but we can easily work around the bug by looking at the Interface Association Descriptor instead. This is most likely what Windows uses too, which explains how the firmware bug has gone unnoticed until now. This change will not affect any currently supported device conforming to the NCM or MBIM specifications, as they must have the CDC Union descriptor. Cc: Greg Suarez <gsuarez@smithmicro.com> Cc: Alexey Orishko <alexey.orishko@stericsson.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21ipv4: Add a socket release callback for datagram socketsSteffen Klassert
This implements a socket release callback function to check if the socket cached route got invalid during the time we owned the socket. The function is used from udp, raw and ping sockets. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21ipv4: Invalidate the socket cached route on pmtu events if possibleSteffen Klassert
The route lookup in ipv4_sk_update_pmtu() might return a route different from the route we cached at the socket. This is because standart routes are per cpu, so each cpu has it's own struct rtable. This means that we do not invalidate the socket cached route if the NET_RX_SOFTIRQ is not served by the same cpu that the sending socket uses. As a result, the cached route reused until we disconnect. With this patch we invalidate the socket cached route if possible. If the socket is owened by the user, we can't update the cached route directly. A followup patch will implement socket release callback functions for datagram sockets to handle this case. Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-21ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transportLuciano Coelho
Add the UART2 muxing data to the board file (this used to be, erroneously, done in the bootloader). Cc: stable <stable@vger.kernel.org> [3.7] Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-01-21ARM: OMAP2+: DT node Timer iteration fixPantelis Antoniou
The iterator correctly handles of_node_put() calls. Remove it before continue'ing the loop. Without this patch you get the following with CONFIG_OF_DYNAMIC set: ERROR: Bad of_node_put() on /ocp/timer@44e31000! [<c001329c>] (unwind_backtrace+0x0/0xe0) from [<c03dd8f0>] (of_node_release+0x2c/0xa0)! [<c03dd8f0>] (of_node_release+0x2c/0xa0) from [<c03ddea0>] (of_find_matching_node_and_match+0x78/0x90)! [<c03ddea0>] (of_find_matching_node_and_match+0x78/0x90) from [<c06d349c>] (omap_get_timer_dt+0x78/0x90)! [<c06d349c>] (omap_get_timer_dt+0x78/0x90) from [<c06d3664>] (omap_dm_timer_init_one.clone.2+0x34/0x2bc)! [<c06d3664>] (omap_dm_timer_init_one.clone.2+0x34/0x2bc) from [<c06d3a2c>] (omap2_gptimer_clocksource_init.clone.4+0x24/0xa8)! [<c06d3a2c>] (omap2_gptimer_clocksource_init.clone.4+0x24/0xa8) from [<c06cca58>] (time_init+0x20/0x30)! [<c06cca58>] (time_init+0x20/0x30) from [<c06c9690>] (start_kernel+0x1a8/0x2fc)! Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Acked-by: Jon Hunter <jon-hunter@ti.com> [tony@atomide.com: updated description per Jon] Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-01-21ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()Tony Lindgren
Otherwise we will get: WARNING: vmlinux.o(.text+0x1d4f0): Section mismatch in reference from the function omap_init_ocp2scp() to the function .init.text:omap_device_build() The function omap_init_ocp2scp() references the function __init omap_device_build(). This is often because omap_init_ocp2scp lacks a __init annotation or the annotation of omap_device_build is wrong. Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-01-21ARM: OMAP2+: fix build break for omapdrmRob Clark
Fixes compile break with 3.8-rc4. Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-01-21ftrace: Be first to run code modification on modulesSteven Rostedt
If some other kernel subsystem has a module notifier, and adds a kprobe to a ftrace mcount point (now that kprobes work on ftrace points), when the ftrace notifier runs it will fail and disable ftrace, as well as kprobes that are attached to ftrace points. Here's the error: WARNING: at kernel/trace/ftrace.c:1618 ftrace_bug+0x239/0x280() Hardware name: Bochs Modules linked in: fat(+) stap_56d28a51b3fe546293ca0700b10bcb29__8059(F) nfsv4 auth_rpcgss nfs dns_resolver fscache xt_nat iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack lockd sunrpc ppdev parport_pc parport microcode virtio_net i2c_piix4 drm_kms_helper ttm drm i2c_core [last unloaded: bid_shared] Pid: 8068, comm: modprobe Tainted: GF 3.7.0-0.rc8.git0.1.fc19.x86_64 #1 Call Trace: [<ffffffff8105e70f>] warn_slowpath_common+0x7f/0xc0 [<ffffffff81134106>] ? __probe_kernel_read+0x46/0x70 [<ffffffffa0180000>] ? 0xffffffffa017ffff [<ffffffffa0180000>] ? 0xffffffffa017ffff [<ffffffff8105e76a>] warn_slowpath_null+0x1a/0x20 [<ffffffff810fd189>] ftrace_bug+0x239/0x280 [<ffffffff810fd626>] ftrace_process_locs+0x376/0x520 [<ffffffff810fefb7>] ftrace_module_notify+0x47/0x50 [<ffffffff8163912d>] notifier_call_chain+0x4d/0x70 [<ffffffff810882f8>] __blocking_notifier_call_chain+0x58/0x80 [<ffffffff81088336>] blocking_notifier_call_chain+0x16/0x20 [<ffffffff810c2a23>] sys_init_module+0x73/0x220 [<ffffffff8163d719>] system_call_fastpath+0x16/0x1b ---[ end trace 9ef46351e53bbf80 ]--- ftrace failed to modify [<ffffffffa0180000>] init_once+0x0/0x20 [fat] actual: cc:bb:d2:4b:e1 A kprobe was added to the init_once() function in the fat module on load. But this happened before ftrace could have touched the code. As ftrace didn't run yet, the kprobe system had no idea it was a ftrace point and simply added a breakpoint to the code (0xcc in the cc:bb:d2:4b:e1). Then when ftrace went to modify the location from a call to mcount/fentry into a nop, it didn't see a call op, but instead it saw the breakpoint op and not knowing what to do with it, ftrace shut itself down. The solution is to simply give the ftrace module notifier the max priority. This should have been done regardless, as the core code ftrace modification also happens very early on in boot up. This makes the module modification closer to core modification. Link: http://lkml.kernel.org/r/20130107140333.593683061@goodmis.org Cc: stable@vger.kernel.org Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Reported-by: Frank Ch. Eigler <fche@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2013-01-21Merge tag 'omap-fixes-b-for-v3.8-rc' of ↵Tony Lindgren
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8-rc4/fixes A few OMAP integration fixes for v3.8-rc, for OMAP4 audio and OMAP2 reboot. Basic test logs are available here: http://www.pwsan.com/omap/testlogs/prcm_fixes_c_v3.8-rc/20130121073904/
2013-01-21ALSA: hda - Add Conexant CX20755/20756/20757 codec IDsTakashi Iwai
These are just compatible with other CX2075x codecs. Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21i2c: mxs: Fix misuse init_completionMarek Vasut
The init_completion() call does reinit not only the variable carrying the flag that the completion finished, but also initialized the waitqueue associated with the completion. On the contrary, the INIT_COMPLETION() call only reinits the flag. In case there was anything still stuck in the waitqueue, subsequent call to init_completion() would be able to create possible race condition. This patch uses the proper function and moves init_completion() into .probe() call of the driver, to be issued only once. Note that such scenario is impossible, since two threads can never enter the mxs_i2c_xfer_msg(), since whole this section is protected by mutex in I2C core. This by no means allows this issue to exit though. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2013-01-22security/device_cgroup: lock assert fails in dev_exception_clean()Jerry Snitselaar
devcgroup_css_free() calls dev_exception_clean() without the devcgroup_mutex being locked. Shutting down a kvm virt was giving me the following trace: [36280.732764] ------------[ cut here ]------------ [36280.732778] WARNING: at /home/snits/dev/linux/security/device_cgroup.c:172 dev_exception_clean+0xa9/0xc0() [36280.732782] Hardware name: Studio XPS 8100 [36280.732785] Modules linked in: xt_REDIRECT fuse ebtable_nat ebtables ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_CHECKSUM iptable_mangle bridge stp llc nf_conntrack_ipv4 ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 nf_defrag_ipv4 ip6table_filter it87 hwmon_vid xt_state nf_conntrack ip6_tables snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_seq coretemp snd_seq_device crc32c_intel snd_pcm snd_page_alloc snd_timer snd broadcom tg3 serio_raw i7core_edac edac_core ptp pps_core lpc_ich pcspkr mfd_core soundcore microcode i2c_i801 nfsd auth_rpcgss nfs_acl lockd vhost_net sunrpc tun macvtap macvlan kvm_intel kvm uinput binfmt_misc autofs4 usb_storage firewire_ohci firewire_core crc_itu_t radeon drm_kms_helper ttm [36280.732921] Pid: 933, comm: libvirtd Tainted: G W 3.8.0-rc3-00307-g4c217de #1 [36280.732922] Call Trace: [36280.732927] [<ffffffff81044303>] warn_slowpath_common+0x93/0xc0 [36280.732930] [<ffffffff8104434a>] warn_slowpath_null+0x1a/0x20 [36280.732932] [<ffffffff812deaf9>] dev_exception_clean+0xa9/0xc0 [36280.732934] [<ffffffff812deb2a>] devcgroup_css_free+0x1a/0x30 [36280.732938] [<ffffffff810ccd76>] cgroup_diput+0x76/0x210 [36280.732941] [<ffffffff8119eac0>] d_delete+0x120/0x180 [36280.732943] [<ffffffff81195cff>] vfs_rmdir+0xef/0x130 [36280.732945] [<ffffffff81195e47>] do_rmdir+0x107/0x1c0 [36280.732949] [<ffffffff8132d17e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [36280.732951] [<ffffffff81198646>] sys_rmdir+0x16/0x20 [36280.732954] [<ffffffff8173bd82>] system_call_fastpath+0x16/0x1b [36280.732956] ---[ end trace ca39dced899a7d9f ]--- Signed-off-by: Jerry Snitselaar <jerry.snitselaar@oracle.com> Cc: stable@kernel.org Signed-off-by: James Morris <james.l.morris@oracle.com>
generated by cgit (git 2.34.1) at 2025-07-16 09:41:31 +0000