| Age | Commit message (Collapse) | Author |
|---|
|
If we compile the WM8994 for a 64bit architecture we receive the following
warnings:
drivers/mfd/wm8994-core.c: In function ‘wm8994_i2c_probe’:
drivers/mfd/wm8994-core.c:639:19:
warning: cast from pointer to integer of different size
wm8994->type = (int)of_id->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
If we compile the MAX8998 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8998.c: In function ‘max8998_i2c_get_driver_data’:
drivers/mfd/max8998.c:178:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
If we compile the MAX8997 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8997.c: In function ‘max8997_i2c_get_driver_data’:
drivers/mfd/max8997.c:173:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Incorrect ADC is picked in ca0132_capture_pcm_prepare(),
where it assumes multiple streams while there is one stream
per ADC. Note that ca0132_capture_pcm_cleanup() already does
the right thing.
The Chromebook Pixel has a microphone under the keyboard that
is attached to node id 0x8. Before this fix, recording would
always go to the main internal mic (node id 0x7).
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When a HDMI stream is opened with the same stream tag
as a following opened stream to ca0132, audio will be
heard from two ports simultaneously.
Fix this issue by change to use snd_hda_codec_setup_stream
and snd_hda_codec_cleanup_stream instead, so that an
inactive stream can be marked as 'dirty' when found
with a conflict stream tag, and then get purified.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Chih-Chung Chang <chihchung@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into clk-fixes
|
|
clk-fixes
mvebu clock fixes for v3.14
- kirkwood, dove, armada-xp, armada-370
- force clock init order broken by sorting DT ocp nodes by address
- fixes boot failures on affected platforms
|
|
The qspi clock divisor is incorrectly set to twice the value it should
have, possibly because it has been computed based on PLL1 as the clock
parent instead of PLL1 / 2 (the datasheets specifies the qspi nominal
frequencies, not the divisor values). Fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The lb, qspi, sdh, sd0 and sd1 clocks have the PLL1 (divided by 2) as
their parent, not the main clock. Fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Today, if
xfs_sb_read_verify
xfs_sb_verify
xfs_mount_validate_sb
detects superblock corruption, it'll be extremely noisy, dumping
2 stacks, 2 hexdumps, etc.
This is because we call XFS_CORRUPTION_ERROR in xfs_mount_validate_sb
as well as in xfs_sb_read_verify.
Also, *any* errors in xfs_mount_validate_sb which are not corruption
per se; things like too-big-blocksize, bad version, bad magic, v1 dirs,
rw-incompat etc - things which do not return EFSCORRUPTED - will
still do the whole XFS_CORRUPTION_ERROR spew when xfs_sb_read_verify
sees any error at all. And it suggests to the user that they
should run xfs_repair, even if the root cause of the mount failure
is a simple incompatibility.
I'll submit that the probably-not-corrupted errors don't warrant
this much noise, so this patch removes the warning for anything
other than EFSCORRUPTED returns, and replaces the lower-level
XFS_CORRUPTION_ERROR with an xfs_notice().
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
When xfs_readsb() does the very first read of the superblock,
it makes a guess at the length of the buffer, based on the
sector size of the underlying storage. This may or may
not match the filesystem sector size in sb_sectsize, so
we can't i.e. do a CRC check on it; it might be too short.
In fact, mounting a filesystem with sb_sectsize larger
than the device sector size will cause a mount failure
if CRCs are enabled, because we are checksumming a length
which exceeds the buffer passed to it.
So always read twice; the first time we read with NULL
buffer ops to skip verification; then set the proper
read length, hook up the proper verifier, and give it
another go.
Once we are sure that we've got the right buffer length,
we can also use bp->b_length in the xfs_sb_read_verify,
rather than the less-trusted on-disk sectorsize for
secondary superblocks. Before this we ran the risk of
passing junk to the crc32c routines, which didn't always
handle extreme values.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
SGI is stepping out of maintainer roles for xfs, xfsprogs, xfsdump, and
xfstests. This removes me from the MAINTAINERS entry.
Signed-off-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
My earlier commit 10e6e65 deserves a layer or two of brown paper
bags. The logic in that commit means that a CRC failure on the
primary superblock will *never* result in an error return.
Hopefully this fixes it, so that we always return the error
if it's a primary superblock, otherwise only if the filesystem
has CRCs enabled.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Fix tegra_init_cache() to check whether the system has a PL310 cache
before touching the PL310 registers. This prevents access to non-existent
registers on Tegra114 and later.
Note for stable kernels:
In <= v3.12, the file to patch is arch/arm/mach-tegra/common.c.
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
'asoc/fix/davinci', 'asoc/fix/fsl', 'asoc/fix/fsl-esai', 'asoc/fix/max98090', 'asoc/fix/rt5640', 'asoc/fix/samsung' and 'asoc/fix/txx9aclc-ac97' into asoc-linus
|
|
Pull drm fixes from Dave Airlie:
"Lots of little small things, nothing too major: nouveau regression
fixes, vmware fixes for the new hw support, memory leaks in error path
fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm/radeon/ni: fix typo in dpm sq ramping setup
drm/radeon/si: fix typo in dpm sq ramping setup
drm/radeon: fix CP semaphores on CIK
drm/radeon: delete a stray tab
drm/radeon: fix display tiling setup on SI
drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
drm/radeon: fill in DRM_CAPs for cursor size
drm: add DRM_CAPs for cursor size
drm/radeon: unify bpc handling
drm/ttm: Fix memory leak in ttm_agp_backend.c
drm/ttm: declare 'struct device' in ttm_page_alloc.h
drm/nouveau: fix TTM_PL_TT memtype on pre-nv50
drm/nv50/disp: use correct register to determine DP display bpp
drm/nouveau/fb: use correct ram oclass for nv1a hardware
drm/nv50/gr: add missing nv_error parameter priv
drm/nouveau: fix ENG_RUNLIST register address
drm/nv4c/bios: disallow retrieving from prom on nv4x igp's
drm/nv4c/vga: decode register is in a different place on nv4x igp's
drm/nv4c/mc: nv4x igp's have a different msi rearm register
drm/nouveau: set irq_enabled manually
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID update from Jiri Kosina:
- fixes for several bugs in incorrect allocations of buffers by David
Herrmann and Benjamin Tissoires.
- support for a few new device IDs by Archana Patni, Benjamin
Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hyperv: make sure input buffer is big enough
HID: Bluetooth: hidp: make sure input buffers are big enough
HID: hid-sensor-hub: quirk for STM Sensor hub
HID: apple: add Apple wireless keyboard 2011 JIS model support
HID: fix buffer allocations
HID: multitouch: add FocalTech FTxxxx support
HID: microsoft: Add ID's for Surface Type/Touch Cover 2
HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay
|
|
The number of the head specifies the index of the display controller
unit and is required to properly configure outputs so that they receive
video data from the correct source.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
fixes
mvebu dt fixes for v3.14
- mvebu: add missing 'eth3' alias for mv78260
- dove: revert PMU interrupt controller node, wait for driver to land.
* tag 'mvebu-dt-fixes-3.14' of git://git.infradead.org/linux-mvebu:
ARM: dove: dt: revert PMU interrupt controller node
ARM: mvebu: dt: add missing alias 'eth3' on Armada XP mv78260
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The powernow-k8 driver maintains a per-cpu data-structure called
powernow_data that is used to perform the frequency transitions.
It initializes this data structure only for the policy->cpu. So,
accesses to this data structure by other CPUs results in various
problems because they would have been uninitialized.
Specifically, if a cpu (!= policy->cpu) invokes the drivers' ->get()
function, it returns 0 as the KHz value, since its per-cpu memory
doesn't point to anything valid. This causes problems during
suspend/resume since cpufreq_update_policy() tries to enforce this
(0 KHz) as the current frequency of the CPU, and this madness gets
propagated to adjust_jiffies() as well. Eventually, lots of things
start breaking down, including the r8169 ethernet card, in one
particularly interesting case reported by Pierre Ossman.
Fix this by initializing the per-cpu data-structures of all the CPUs
in the policy appropriately.
References: https://bugzilla.kernel.org/show_bug.cgi?id=70311
Reported-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 42f921a (cpufreq: remove sysfs files for CPUs which failed to
come back after resume) tried to do this but missed this piece of code
to fix.
Currently we are getting this on suspend/resume:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 877 at fs/sysfs/dir.c:52 sysfs_warn_dup+0x68/0x84()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu1/cpufreq'
Modules linked in: brcmfmac brcmutil
CPU: 0 PID: 877 Comm: test-rtc-resume Not tainted 3.14.0-rc2-00259-g9398a10cd964 #12
[<c0015bac>] (unwind_backtrace) from [<c0011850>] (show_stack+0x10/0x14)
[<c0011850>] (show_stack) from [<c056e018>] (dump_stack+0x80/0xcc)
[<c056e018>] (dump_stack) from [<c0025e44>] (warn_slowpath_common+0x64/0x88)
[<c0025e44>] (warn_slowpath_common) from [<c0025efc>] (warn_slowpath_fmt+0x30/0x40)
[<c0025efc>] (warn_slowpath_fmt) from [<c012776c>] (sysfs_warn_dup+0x68/0x84)
[<c012776c>] (sysfs_warn_dup) from [<c0127a54>] (sysfs_do_create_link_sd+0xb0/0xb8)
[<c0127a54>] (sysfs_do_create_link_sd) from [<c038ef64>] (__cpufreq_add_dev.isra.27+0x2a8/0x814)
[<c038ef64>] (__cpufreq_add_dev.isra.27) from [<c038f548>] (cpufreq_cpu_callback+0x70/0x8c)
[<c038f548>] (cpufreq_cpu_callback) from [<c0043864>] (notifier_call_chain+0x44/0x84)
[<c0043864>] (notifier_call_chain) from [<c0025f60>] (__cpu_notify+0x28/0x44)
[<c0025f60>] (__cpu_notify) from [<c00261e8>] (_cpu_up+0xf0/0x140)
[<c00261e8>] (_cpu_up) from [<c0569eb8>] (enable_nonboot_cpus+0x68/0xb0)
[<c0569eb8>] (enable_nonboot_cpus) from [<c006339c>] (suspend_devices_and_enter+0x198/0x2dc)
[<c006339c>] (suspend_devices_and_enter) from [<c0063654>] (pm_suspend+0x174/0x1e8)
[<c0063654>] (pm_suspend) from [<c00624e0>] (state_store+0x6c/0xbc)
[<c00624e0>] (state_store) from [<c01fc200>] (kobj_attr_store+0x14/0x20)
[<c01fc200>] (kobj_attr_store) from [<c0126e50>] (sysfs_kf_write+0x44/0x48)
[<c0126e50>] (sysfs_kf_write) from [<c012a274>] (kernfs_fop_write+0xb4/0x14c)
[<c012a274>] (kernfs_fop_write) from [<c00d4818>] (vfs_write+0xa8/0x180)
[<c00d4818>] (vfs_write) from [<c00d4bb8>] (SyS_write+0x3c/0x70)
[<c00d4bb8>] (SyS_write) from [<c000e620>] (ret_fast_syscall+0x0/0x30)
---[ end trace 76969904b614c18f ]---
Fix this by removing sysfs link for cpufreq directory when cpu removed
isn't policy->cpu.
Revamps: 42f921a (cpufreq: remove sysfs files for CPUs which failed to come back after resume)
Reported-and-tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When building a kernel image with only CONFIG_CPU_IDLE but no CONFIG_PM,
we will get the following link error.
LD init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_enter_wait':
platform-spi_imx.c:(.text+0x25c0): undefined reference to `imx6q_set_lpm'
platform-spi_imx.c:(.text+0x25d4): undefined reference to `imx6q_set_lpm'
arch/arm/mach-imx/built-in.o: In function `imx6q_cpuidle_init':
platform-spi_imx.c:(.init.text+0x75d4): undefined reference to `imx6q_set_chicken_bit'
make[1]: *** [vmlinux] Error 1
Since pm-imx6q.c has been a collection of library functions that access
CCM low-power registers used by not only suspend but also cpuidle and
other drivers, let's build pm-imx6q.c independently of CONFIG_PM to fix
above error.
Reported-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@vger.kernel.org
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps, mostly to deal with the 34xx vs 36xx SoC
configuration for overo boards.
* tag 'omap-for-v3.14/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
ARM: dts: am335x-evmsk: Fix mmc1 support
ARM: DTS: am335x-evmsk: Correct audio clock frequency
ARM: dts: omap3-gta04: Add EOC irq gpio line handling.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This alias entry was evidently cut/paste from a different board, and
not correctly updated to match Cardhu. Fix this.
Fixes: 553c0a200e20 ("ARM: tegra: set up /aliases entries for RTCs")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When trying to set the minimum temperature, the driver was erroneously
writing the maximum temperature into the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # v3.2+
Reviewed-by: Jean Delvare <jdelvare@suse.de>
|
|
Pull networking fixes from David Miller:
1) kvaser CAN driver has fixed limits of some of it's table, validate
that we won't exceed those limits at probe time. Fix from Olivier
Sobrie.
2) Fix rtl8192ce disabling interrupts for too long, from Olivier
Langlois.
3) Fix botched shift in ath5k driver, from Dan Carpenter.
4) Fix corruption of deferred packets in TIPC, from Erik Hugne.
5) Fix newlink error path in macvlan driver, from Cong Wang.
6) Fix netpoll deadlock in bonding, from Ding Tianhong.
7) Handle GSO packets properly in forwarding path when fragmentation is
necessary on egress, from Florian Westphal.
8) Fix axienet build errors, from Michal Simek.
9) Fix refcounting of ubufs on tx in vhost net driver, from Michael S
Tsirkin.
10) Carrier status isn't set properly in hyperv driver, from Haiyang
Zhang.
11) Missing pci_disable_device() in tulip_remove_one), from Ingo Molnar.
12) AF_PACKET qdisc bypass mode doesn't adhere to driver provided TX
queue selection method. Add a fallback method mechanism to fix this
bug, from Daniel Borkmann.
13) Fix regression in link local route handling on GRE tunnels, from
Nicolas Dichtel.
14) Bonding can assign dup aggregator IDs in some sequences of
configuration, fix by making the allocation counter per-bond instead
of global. From Jiri Bohac.
15) sctp_connectx() needs compat translations, from Daniel Borkmann.
16) Fix of_mdio PHY interrupt parsing, from Ben Dooks
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
MAINTAINERS: add entry for the PHY library
of_mdio: fix phy interrupt passing
net: ethernet: update dependency and help text of mvneta
NET: fec: only enable napi if we are successful
af_packet: remove a stray tab in packet_set_ring()
net: sctp: fix sctp_connectx abi for ia32 emulation/compat mode
ipv4: fix counter in_slow_tot
irtty-sir.c: Do not set_termios() on irtty_close()
bonding: 802.3ad: make aggregator_identifier bond-private
usbnet: remove generic hard_header_len check
gre: add link local route when local addr is any
batman-adv: fix potential kernel paging error for unicast transmissions
batman-adv: avoid double free when orig_node initialization fails
batman-adv: free skb on TVLV parsing success
batman-adv: fix TT CRC computation by ensuring byte order
batman-adv: fix potential orig_node reference leak
batman-adv: avoid potential race condition when adding a new neighbour
batman-adv: properly check pskb_may_pull return value
batman-adv: release vlan object after checking the CRC
batman-adv: fix TT-TVLV parsing on OGM reception
...
|
|
Pull ARM fixes from Russell King:
"A range of ARM fixes. Biggest change is the stage-2 attributes used
for for hyp mode which were wrong. I've killed some bits in a couple
of DT files which turned out not to be required, and a few other
fixes.
One fix touches code outside of arch/arm, which is related to sorting
out the DMA masks correctly. There is a long standing issue with the
conversion from PFNs to addresses where people assume that shifting an
unsigned long left by PAGE_SHIFT results in a correct address. This
is not the case with C: the integer promotion happens at assignment
after evaluation. This fixes the recently introduced dma_max_pfn()
function, but there's a number of other places where we try this
directly on an unsigned long in the mm code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
Fix uses of dma_max_pfn() when converting to a limiting address
ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
ARM: 7950/1: mm: Fix stage-2 device memory attributes
ARM: dts: fix spdif pinmux configuration
|
|
Pull jfs fix from David Kleikamp:
"Another ACL regression. This one more subtle"
* tag 'jfs-3.14-rc4' of git://github.com/kleikamp/linux-shaggy:
jfs: set i_ctime when setting ACL
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux into fixes
* tag 'pwm_pxa_for_v3.14' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux:
ARM: pxa: Add dummy backlight power supply on Mitac Mio A701
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Currently, there's nothing preventing cgroup_enable_task_cg_lists()
from missing set PF_EXITING and race against cgroup_exit(). Depending
on the timing, cgroup_exit() may finish with the task still linked on
css_set leading to list corruption. Fix it by grabbing siglock in
cgroup_enable_task_cg_lists() so that PF_EXITING is guaranteed to be
visible.
This whole on-demand cg_list optimization is extremely fragile and has
ample possibility to lead to bugs which can cause things like
once-a-year oops during boot. I'm wondering whether the better
approach would be just adding "cgroup_disable=all" handling which
disables the whole cgroup rather than tempting fate with this
on-demand craziness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: stable@vger.kernel.org
|
|
The PHY library has been subject to some changes, new drivers and DT
interactions over the past few months. Add myself as a maintainer for
the core PHY library parts and drivers. Make sure the PHY library entry
also covers the Device Tree files which have a close interaction with
the MDIO bus, PHY connection and Ethernet PHY mode parsing.
CC: Grant Likely <grant.likely@linaro.org>
CC: Shaohui Xie <shaohui.xie@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The of_mdiobus_register_phy() is not setting phy->irq thus causing
some drivers to incorrectly assume that the PHY does not have an
IRQ associated with it. Not only do some drivers report no IRQ
they do not install an interrupt handler for the PHY.
Simplify the code setting irq and set the phy->irq at the same
time so that we cover the following issues, which should cover
all the cases the code will find:
- Set phy->irq if node has irq property and mdio->irq is NULL
- Set phy->irq if node has no irq and mdio->irq is not NULL
- Leave phy->irq as PHY_POLL default if none of the above
This fixes the issue:
net eth0: attached PHY 1 (IRQ -1) to driver Micrel KSZ8041RNLI
to the correct:
net eth0: attached PHY 1 (IRQ 416) to driver Micrel KSZ8041RNLI
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the introduction of the support for Armada 375 and Armada 38x,
the hidden Kconfig option MACH_ARMADA_370_XP is being renamed to
MACH_MVEBU_V7. Therefore, the dependency that was used for the mvneta
driver can no longer work. This commit replaces this dependency by a
dependency on PLAT_ORION, which is used similarly for the mv643xx_eth
driver.
In addition to this, it takes this opportunity to adjust the
description and help text to indicate that the driver can is also used
for Armada 38x. Note that Armada 375 cannot use this driver as it has
a completely different networking unit, which will require a separate
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If napi is left enabled after a failed attempt to bring the interface
up, we BUG:
fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc
Only enable napi after we are past all the failure paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At first glance it looks like there is a missing curly brace but
actually the code works the same either way. I have adjusted the
indenting but left the code the same.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 06b29e76a74b2373e6f8b5a7938b3630b9ae98b2.
As pointed out by Grant Likely, we should also take the type and name
into account when searching the best compatible match. That means the
match with compatible, type and name should be better than the match
just with the same compatible string. So revert this and we will
implement another method to find the best match entry.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
Pull request of 2014-02-18
One compile fix and one memory leak.
* tag 'ttm-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
drm/ttm: Fix memory leak in ttm_agp_backend.c
drm/ttm: declare 'struct device' in ttm_page_alloc.h
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
Pull request of 2014-02-18.
Nothing special. The biggest change is adding a couple of command defines and
packing the command data correctly.
* tag 'vmwgfx-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix command defines and checks
drm/vmwgfx: Fix possible integer overflow
drm/vmwgfx: Remove stray const
drm/vmwgfx: unlock on error path in vmw_execbuf_process()
drm/vmwgfx: Get maximum mob size from register SVGA_REG_MOB_MAX_SIZE
drm/vmwgfx: Fix a couple of sparse warnings and errors
|
|
into drm-fixes
Fix for 128x128 cursors, along with some misc fixes.
* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/ni: fix typo in dpm sq ramping setup
drm/radeon/si: fix typo in dpm sq ramping setup
drm/radeon: fix CP semaphores on CIK
drm/radeon: delete a stray tab
drm/radeon: fix display tiling setup on SI
drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
drm/radeon: fill in DRM_CAPs for cursor size
drm: add DRM_CAPs for cursor size
drm/radeon: unify bpc handling
|
|
git://git.rocketboards.org/linux-socfpga-next into clk-next
SOCFPGA clk updates for v3.15
|
|
The clk-phase property is used to represent the 2 clock phase values that is
needed for the SD/MMC driver. Add a prepare function to the clk_ops, that will
use the syscon driver to set sdmmc_clk's phase shift that is located in the
system manager.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
---
v9: none
v8: Use degrees in the clk-phase binding property
v7: Add dts property to represent the clk phase of the sdmmc_clk. Add a
prepare function to the gate clk that will toggle clock phase setting.
Remove the "altr,socfpga-sdmmc-sdr-clk" clock type.
v6: Add a new clock type "altr,socfpga-sdmmc-sdr-clk" that will be used to
set the phase shift settings.
v5: Use the "snps,dw-mshc" binding
v4: Use the sdmmc_clk prepare function to set the phase shift settings
v3: Not use the syscon driver because as of 3.13-rc1, the syscon driver is
loaded after the clock driver.
v2: Use the syscon driver
|
|
Move the different kinds of clocks into their own files. The reason is to aid
readability of the code. This also goes along with the other SoC-specific
clock drivers.
The split introduces new structs for the three types of clocks and uses them.
Other changes are not done to the code.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
|
|
It should be SOCFPGA instead of SOCFGPA.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
|
|
The clk_name field from the socfpga_clk struct is unused.
Remove it.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
|
|
The only thing that socfpga_init_clocks was doing is setting up the smp_twd clk.
Now that twd-timer's clock phandle is populated in the DTS, we can remove
this function.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
After the patch:
"clk: socfpga: Map the clk manager base address in the clock driver"
The clk->name field in socfpga_clk_recalc_rate() was getting cleared. Replace
looking for the GPIO_DB_CLK by its divider offset instead.
Also rename the define SOCFPGA_DB_CLK_OFFSET -> SOCFPGA_GPIO_DB_CLK_OFFSET, as
this represents the GPIO_DB_CLK.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
|
|
The clk manager's base address was being mapped in SOCFPGA's arch code and
being extern'ed out to the clock driver. This method is not correct, and the
arch code was not really doing anything with that clk manager anyways.
This patch moves the mapping of the clk manager's base address in the clock
driver itself. Cleans up CLK_OF_DECLARE() into a single registration of all
the clocks.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
v2: Use a static declaration for the clk_mgr_base_addr. Clean up the
CLK_OF_DECLARE() as suggested by Arnd.
|
|
Contradicting to documenation, the notifier callbacks do receive
the original clock rate in struct clk_notifier_data.old_rate and the new
frequency struct clk_notifier_data.new_rate, independent of the
notification reason.
This behavior also seems to make more sense, since callbacks can use the
same code to deterimine whether clocks are scaled up or down. Something
which would not even possible in the post-rate-change case if the
behavior was as documented.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.14 stream...
For the iwlwifi one, Emmanuel says:
"As explicitly written in the commit message, we prefer to disable Tx
AMPDU on NICs supported by iwldvm. This feature gives a big boost in
Tx performance, but the firmware is buggy and we can't rely on it.
Our hope is that most of the users out there want wifi to surf on
the web which means that they care more for Rx traffic than for Tx.
People who want to enable it can do so with the help of a module
parameter."
On top of that...
Dan Carpenter fixes a typo/thinko in ath5k.
Olivier Langlois fixes a couple of rtlwifi issues, one which leaves
IRQs disabled too long (causing a variety of problems elsewhere),
and one which fixes an incorrect return code when failing to enable
the NIC.
Russell King fixes a NULL pointer dereference in hostap.
Stanislaw Gruszka fixes a DMA coherence issue in the rtl8187 driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
