| Age | Commit message (Collapse) | Author |
|---|
|
This commit adds the CPU_METHOD_OF_DECLARE declaration for the Armada
XP SMP operations. Note that the .smp_ops field of Armada XP
DT_MACHINE structure is kept, in order to ensure we remain compatible
with older Device Trees that do not include the "enable-method"
property for the CPUs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483648-26611-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The pmsu.c driver contained an armada_xp_boot_cpu() function that sets
the boot address of a secondary CPUs and deasserts the reset. However,
the Armada 375 needs a slightly different logic, so it makes more
sense to move this code into the Armada XP specific platsmp.c.
In order to achieve this, the mvebu_pmsu_set_cpu_boot_addr() function
is exported. It will be needed for both the Armada XP and Armada 38x
SMP implementations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483648-26611-2-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
|
|
Non-DT irq handlers were working through irq causes from most-significant
to least-significant bit, while DT irqchip driver does it the other way
round. This revealed some more HW issues on Kirkwood peripheral IP, where
spurious sdio irqs can happen although irqs are masked.
Also, the generated binaries show that original non-DT order compared
to DT order save two instructions for each bit count check:
irqchip DT order with ffs():
60: e3a06001 mov r6, #1
64: e2643000 rsb r3, r4, #0
68: e0033004 and r3, r3, r4
6c: e16f3f13 clz r3, r3
70: e263301f rsb r3, r3, #31
74: e1c44316 bic r4, r4, r6, lsl r3
78: e5971004 ldr r1, [r7, #4]
Original non-DT order with fls():
60: e3a07001 mov r7, #1
64: e16f3f14 clz r3, r4
68: e263301f rsb r3, r3, #31
6c: e1c44317 bic r4, r4, r7, lsl r3
70: e5951004 ldr r1, [r5, #4]
Therefore, reverse irq bit handling back to original order by replacing
ffs() with fls().
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398719528-23607-1-git-send-email-sebastian.hesselbarth@gmail.com
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Some irqchip initialization must be done on secondary CPUs. On mvebu
platforms, this is currently achieved by having the
arch/arm/mach-mvebu/platsmp.c code directly call into a function
exported by the irqchip driver, which isn't really nice.
This commit changes this by using the same solution as the one used in
the GIC driver: the irqchip driver registers a CPU notifier, which is
used to do the secondary CPU IRQ initialization. This way, the irqchip
driver is completely autonomous, and the function no longer needs to
be exposed from the irqchip driver to the SoC code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483648-26611-6-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Instead of having the SoC code in arch/arm/mach-mvebu/platsmp.c do the
set_smp_cross_call() to register the IPI-triggering function, it makes
more sense to do exactly what the GIC driver is doing: let the irqchip
driver do it. This way, it avoids having to expose the
armada_mpic_send_doorbell() function between the irqchip driver and
the SoC code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483648-26611-5-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The tsadcc node is useless as it doesn't refer to anything and the touchscreen
is handled by the adc0 node.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The atmel_tsadcc driver is not used anymore, it has been replaced by at91_adc so
remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
atmel_tsadcc has been removed, stop selecting it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
atmel_tsadcc is not allowing to use the remaining ADC channels while at91_adc
does. Completely switch to at91_adc and remove the tsadcc platform_data for
at91sam9rl and at91sam9rl based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
atmel_tsadcc is not allowing to use the remaining ADC channels while at91_adc
does. Completely switch to at91_adc and remove the tsadcc platform_data for
at91sam9g45 and at91sam9g45 based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
at91_adc now supports reading a touchscreen for ADCs without a TSMR register.
Enable touchscreen support through at91_adc. This allows to use both a
touchscreen and the remaining ADC channel at the same time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The ADC clock needs to be defined to enable the at91_adc driver. It is defined
to the same speed that is used for atmel_tsadcc.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
That include file is now only used by the at91_adc driver, remove it from
include/mach for better driver separation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
at91_adc now supports reading a touchscreen for ADCs without a TSMR register.
Enable touchscreen support through at91_adc. This allows to use both a
touchscreen and the remaining ADC channel at the same time.
Also, lower the clock for the ADC as it allows to have more stable reads and
this is the speed used by atmel_tsadcc.
It lowers the maximum throughput rate from 440000 samples per second to 12958
samples per second. It shouldn't be an issue as the CPU is not able to keep up
reading samples at that frequency.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Old ADCs, as present on the sam9rl and the sam9g45 don't have a TSMR register
and the touchscreen support should be handled differently.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
num_channels and registers are not used anymore since they are defined inside
the driver and assigned by matching the id_table.
Also, struct at91_adc_reg_desc is now only used inside the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
num_channels and registers are not used anymore since they are defined inside
the at91_adc driver and assigned by matching the id_table.
Also, remove the mach/at91_adc.h include that is not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
num_channels and registers are not used anymore since they are defined inside
the at91_adc driver and assigned by matching the id_table.
Also, remove the mach/at91_adc.h include that is not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Define at91sam9rlek crystal frequencies.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Move at91sam9rl SoC to the new main/slow clock model.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Define at91sam9261ek main crystal frequency.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Jean-Jacques HIBLOT <jjhiblot@traphandler.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Jean-Jacques HIBLOT <jjhiblot@traphandler.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Define crystal properties of sama5d3 xplained board.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Define crystal frequencies of sama5d3xcm boards.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Replace the old main and clk definitions (fixed rate clk) by the new main and
slow clk subtree definition (ck = mux(rc_osc, osc)).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add slow clk, and slow oscillators documentation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
AT91 slow clk is a clk multiplexer.
In some SoCs (sam9x5, sama5, sam9g45 families) this multiplexer can
choose among 2 sources: an internal RC oscillator circuit and an oscillator
using an external crystal.
In other Socs (sam9260 family) the multiplexer source is hardcoded with
the OSCSEL signal.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Update main clk documentation to match main clk implementation rework.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
AT91 main clk is a clk multiplexer and not a simple fixed rate clk as
currently implemented.
In some SoCs (sam9x5, sama5, sam9g45 families) this multiplexer can
choose among 2 sources: an internal RC oscillator circuit and an
oscillator using an external crystal.
In other Socs (sam9260, rm9200 families) the multiplexer source is
hardcoded to the external crystal oscillator.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This moves the <mach/gpio.h> header in the AT91 platform down
into the machine directory and removes the reliance on
MACH_NEED_GPIO_H from the AT91.
This does not move the platform to GENERIC_GPIO but localize
the remaining work to be done for this to the mach-at91
folder.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[nicolas.ferre@atmel.com: adapt to newer kernel, add rsi-ews board]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This include file is about to disapear. In addition it is
useless for this code. So it is time to remove it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Brown <broonie@linaro.org>
|
|
The boot ROM on Tegra SoCs supports booting into forced recovery mode
(RCM) by setting a bit in the PMC scratch register 0. Similarily, the
Android bootloader examines some of the bits in this register to disable
autoboot or enter recovery mode.
Support these modes by setting the corresponding bits depending on the
specified reboot command (forced-recovery, bootloader, recovery). Recent
systemd-based distributions allow this to be specified using an optional
argument to the reboot command.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Second Round of Renesas ARM Based SoC Updates for v3.16" from Simon
Horman:
Power management code which is only used by
sh7372 (SH-Mobile AP4) based Mackerl board
* Ignore callbacks for subsys generic_pm_domain_data
* tag 'renesas-soc2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Ignore callbacks for subsys generic_pm_domain_data
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Clock Updates for v3.16" from Simon Horman:
SH Mobile shared clock code
* Introduce shmobile_clk_workaround()
r8a7791 (R-Car M2) SoC
* Rename VSP1_SY clocks to VSP1_S
* Correct the I2C clocks parents
r8a7790 (R-Car H2) SoC
* Remove old style audio clock
* Rename VSP1_(SY|RT) clocks to VSP1_(S|R)
* Fix the I2C clocks parents
r8a7778 (R-Car M1) SoC
* Remove old style audio clock
* tag 'renesas-clock-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: remove old style audio clock
ARM: shmobile: r8a7778: remove old style audio clock
ARM: shmobile: r8a7791: Rename VSP1_SY clocks to VSP1_S
ARM: shmobile: r8a7790: Rename VSP1_(SY|RT) clocks to VSP1_(S|R)
ARM: shmobile: r8a7791: Fix the I2C clocks parents in legacy code
ARM: shmobile: r8a7790: Fix the I2C clocks parents in legacy code
ARM: shmobile: Introduce shmobile_clk_workaround()
ARM: shmobile: r8a7791: Use rcar_gen2_read_mode_pins() helper
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Updates for v3.16" from Simon Horman:
SH Mobile shared SoC code
* Add shared shmobile_init_delay()
r8a7791 (R-Car M2) and r8a7790 (R-Car H2) SoCs (R-Car Gen2 shared code)
* Cache Mode Monitor Register Value
r8a7791 (R-Car M2) SoC
Check r8a7791 MD21 at SMP boot
r8a7790 (R-Car H2) SoC
* Make use of r8a7790_add_standard_devices()
* Update r8a7791 CPU freq to 1500MHz
r8a7778 (R-Car M1) SoC
* Move "select RENESAS_INTC_IRQPIN" under SoC
emev2 (Emma Mobale EV2) SoC
* Remove legacy EMEV2 SoC support
* tag 'renesas-soc-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7778/bockw: Move "select RENESAS_INTC_IRQPIN" under SoC
ARM: shmobile: Check r8a7791 MD21 at SMP boot
ARM: shmobile: rcar-gen2: Cache Mode Monitor Register Value
ARM: shmobile: Make use of r8a7790_add_standard_devices()
ARM: shmobile: Remove EMEV2 header file
ARM: shmobile: Remove legacy EMEV2 SoC support
ARM: shmobile: Add shared shmobile_init_delay()
ARM: shmobile: Update r8a7791 CPU freq to 1500MHz in C
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This will allow to better isolate various options, and reduce the overall
kernel size if we're interested in only one of the SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
|
|
Pull file locking change from Jeff Layton:
"Only an email address change to the MAINTAINERS file"
* tag 'locks-v3.15-3' of git://git.samba.org/jlayton/linux:
MAINTAINERS: email address change for Jeff Layton
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"These are mostly arm64 fixes with an additional arm(64) platform fix
for the initialisation of vexpress clocks (the latter only affecting
arm64; the arch/arm64 code is SoC agnostic and does not rely on early
SoC-specific calls)
- vexpress platform clocks initialisation moved earlier following the
arm64 move of of_clk_init() call in a previous commit
- Default DMA ops changed to non-coherent to preserve compatibility
with 32-bit ARM DT files. The "dma-coherent" property can be used
to explicitly mark a device coherent. The Applied Micro DT file
has been updated to avoid DMA cache maintenance for the X-Gene SATA
controller (the only arm64 related driver with such assumption in
-rc mainline)
- Fixmap correction for earlyprintk
- kern_addr_valid() fix for huge pages"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
vexpress: Initialise the sysregs before setting up the clocks
arm64: Mark the Applied Micro X-Gene SATA controller as DMA coherent
arm64: Use bus notifiers to set per-device coherent DMA ops
arm64: Make default dma_ops to be noncoherent
arm64: fixmap: fix missing sub-page offset for earlyprintk
arm64: Fix for the arm64 kern_addr_valid() function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is two patches both fixing bugs in drivers (virtio-scsi and
mpt2sas) causing an oops in certain circumstances"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio-scsi: Skip setting affinity on uninitialized vq
[SCSI] mpt2sas: Don't disable device twice at suspend.
|
|
Following arm64 commit bc3ee18a7a57 (arm64: init: Move of_clk_init to
time_init()), vexpress_osc_of_setup() is called via of_clk_init() long
before initcalls are issued. Initialising the vexpress oscillators
requires the vespress sysregs to be already initialised, so this patch
adds an explicit call to vexpress_sysreg_of_early_init() in vexpress
oscillator setup function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
|
|
Since the default DMA ops for arm64 are non-coherent, mark the X-Gene
controller explicitly as dma-coherent to avoid additional cache
maintenance.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Loc Ho <lho@apm.com>
|
|
Recently, the default DMA ops have been changed to non-coherent for
alignment with 32-bit ARM platforms (and DT files). This patch adds bus
notifiers to be able to set the coherent DMA ops (with no cache
maintenance) for devices explicitly marked as coherent via the
"dma-coherent" DT property.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Currently arm64 dma_ops is by default made coherent which makes it
opposite in default policy from arm.
Make default dma_ops to be noncoherent (same as arm), as currently there
aren't any dma-capable drivers which assumes coherent ops
Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Commit d57c33c5daa4 (add generic fixmap.h) added (among other
similar things) set_fixmap_io to deal with early ioremap of devices.
More recently, commit bf4b558eba92 (arm64: add early_ioremap support)
converted the arm64 earlyprintk to use set_fixmap_io. A side effect of
this conversion is that my virtual machines have stopped booting when
I pass "earlyprintk=uart8250-8bit,0x3f8" to the guest kernel.
Turns out that the new earlyprintk code doesn't care at all about
sub-page offsets, and just assumes that the earlyprintk device will
be page-aligned. Obviously, that doesn't play well with the above example.
Further investigation shows that set_fixmap_io uses __set_fixmap instead
of __set_fixmap_offset. A fix is to introduce a set_fixmap_offset_io that
uses the latter, and to remove the superflous call to fix_to_virt
(which only returns the value that set_fixmap_io has already given us).
With this applied, my VMs are back in business. Tested on a Cortex-A57
platform with kvmtool as platform emulation.
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Salter <msalter@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Fix for the arm64 kern_addr_valid() function to recognize
virtual addresses in the kernel logical memory map. The
function fails as written because it does not check whether
the addresses in that region are mapped at the pmd level to
2MB or 512MB pages, continues the page table walk to the
pte level, and issues a garbage value to pfn_valid().
Tested on 4K-page and 64K-page kernels.
Signed-off-by: Dave Anderson <anderson@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"This udpate delivers:
- A fix for dynamic interrupt allocation on x86 which is required to
exclude the GSI interrupts from the dynamic allocatable range.
This was detected with the newfangled tablet SoCs which have GPIOs
and therefor allocate a range of interrupts. The MSI allocations
already excluded the GSI range, so we never noticed before.
- The last missing set_irq_affinity() repair, which was delayed due
to testing issues
- A few bug fixes for the armada SoC interrupt controller
- A memory allocation fix for the TI crossbar interrupt controller
- A trivial kernel-doc warning fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: irq-crossbar: Not allocating enough memory
irqchip: armanda: Sanitize set_irq_affinity()
genirq: x86: Ensure that dynamic irq allocation does not conflict
linux/interrupt.h: fix new kernel-doc warnings
irqchip: armada-370-xp: Fix releasing of MSIs
irqchip: armada-370-xp: implement the ->check_device() msi_chip operation
irqchip: armada-370-xp: fix invalid cast of signed value into unsigned variable
|
