| Age | Commit message (Collapse) | Author |
|---|
|
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Now with wlcore using PM runtime, we can also add support for Linux
generic wakeirq handling for it if configured in the dts file.
The wakeirq can be configured as the second interrupt in the dts file
with interrupts-extended property where it is the padconf irq of the OOB
GPIO pin used for wlcore interrupt.
Note that eventually we should also allow configuring wlcore to use the
SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be
configured to be the padconf interrupt of the dat1 pin and not the
padconf interrupt of the OOB GPIO pin.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:
BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...
After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.
And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The following:
bool efuse_re_pg_sec1flag;
u8 efuse_re_pg_data[8];
are not referenced anywhere in the rtlwifi code.
This patch is originally created by Rick Veens <rickveens92@gmail.com>,
and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Boris Ostrovsky reported a memory leak with device passthrough when SME
is active.
The VFIO driver uses iommu_iova_to_phys() to get the physical address for
an iova. This physical address is later passed into vfio_unmap_unpin() to
unpin the memory. The vfio_unmap_unpin() uses pfn_valid() before unpinning
the memory. The pfn_valid() check was failing because encryption mask was
part of the physical address returned. This resulted in the memory not
being unpinned and therefore leaked after the guest terminates.
The memory encryption mask must be cleared from the physical address in
iommu_iova_to_phys().
Fixes: 2543a786aa25 ("iommu/amd: Allow the AMD IOMMU to work with memory encryption")
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: <iommu@lists.linux-foundation.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.
Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().
This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.
Fixes: 9525ae83959b6 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83ebc ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b70567f ("be2net: Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
Third set of PPC KVM fixes for 4.19
One patch here, fixing a potential host crash introduced (or at least
exacerbated) by a previous fix for corruption relating to radix guest
page faults and THP operations.
|
|
In commit ec3ed293e766 ("net_sched: change tcf_del_walker() to take idrinfo->lock")
we move fl_hw_destroy_tmplt() to a workqueue to avoid blocking
with the spinlock held. Unfortunately, this causes a lot of
troubles here:
1. tcf_chain_destroy() could be called right after we queue the work
but before the work runs. This is a use-after-free.
2. The chain refcnt is already 0, we can't even just hold it again.
We can check refcnt==1 but it is ugly.
3. The chain with refcnt 0 is still visible in its block, which means
it could be still found and used!
4. The block has a refcnt too, we can't hold it without introducing a
proper API either.
We can make it working but the end result is ugly. Instead of wasting
time on reviewing it, let's just convert the troubling spinlock to
a mutex, which allows us to use non-atomic allocations too.
Fixes: ec3ed293e766 ("net_sched: change tcf_del_walker() to take idrinfo->lock")
Reported-by: Ido Schimmel <idosch@idosch.org>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Magnus Karlsson says:
====================
Previously, the xsk code did not record which umem was bound to a
specific queue id. This was not required if all drivers were zero-copy
enabled as this had to be recorded in the driver anyway. So if a user
tried to bind two umems to the same queue, the driver would say
no. But if copy-mode was first enabled and then zero-copy mode (or the
reverse order), we mistakenly enabled both of them on the same umem
leading to buggy behavior. The main culprit for this is that we did
not store the association of umem to queue id in the copy case and
only relied on the driver reporting this. As this relation was not
stored in the driver for copy mode (it does not rely on the AF_XDP
NDOs), this obviously could not work.
This patch fixes the problem by always recording the umem to queue id
relationship in the netdev_queue and netdev_rx_queue structs. This way
we always know what kind of umem has been bound to a queue id and can
act appropriately at bind time. To make the bind semantics consistent
with ethtool queue manipulations and to facilitate the implementation
of drivers, we also forbid decreasing the number of queues/channels
with ethtool if there is an active AF_XDP socket in the set of queues
that are disabled.
Jakub, please take a look at your patches. The last one I had to
change slightly to make it fit with the new interface
xdp_get_umem_from_qid(). An added bonus with this function is that we,
in the future, can also use it from the driver to get a umem, thus
simplifying driver implementations (and later remove the umem from the
NDO completely). Björn will mail patches, at a later point in time,
using this in the i40e and ixgbe drivers, that removes a good chunk of
code from the ZC implementations. I also made your code aware of Tx
queues. If we create a socket that only has a Tx queue, then the queue
id will refer to a Tx queue id only and could be larger than the
available amount of Rx queues. Please take a look at it.
Differences against v1:
* Included patches from Jakub that forbids decreasing the number of active
queues if a queue to be deactivated has an AF_XDP socket. These have
been adapted somewhat to the new interfaces in patch 2.
* Removed redundant check against real_num_[rt]x_queue in xsk_bind
* Only need to test against real_num_[rt]x_queues in
xdp_clear_umem_at_qid.
Patch 1: Introduces a umem reference in the netdev_rx_queue and
netdev_queue structs.
Patch 2: Records which queue_id is bound to which umem and make sure
that you cannot bind two different umems to the same queue_id.
Patch 3: Pre patch to ethtool_set_channels.
Patch 4: Forbid decreasing the number of active queues if a deactivated
queue has an AF_XDP socket.
Patch 5: Simplify xdp_clear_umem_at_qid now when ethtool cannot deactivate
the queue id we are running on.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
As we now do not allow ethtool to deactivate the queue id we are
running an AF_XDP socket on, we can simplify the implementation of
xdp_clear_umem_at_qid().
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
We already check the RSS indirection table does not use queues which
would be disabled by channel reconfiguration. Make sure user does not
try to disable queues which have a UMEM and zero-copy AF_XDP socket
installed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
ethtool_set_channels() validates the config against driver's max
settings. It retrieves the current config and stores it in a
variable called max. This was okay when only max settings were
accessed but we will soon want to access current settings as
well, so calling the entire structure max makes the code less
readable.
While at it drop unnecessary parenthesis.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Previously, the xsk code did not record which umem was bound to a
specific queue id. This was not required if all drivers were zero-copy
enabled as this had to be recorded in the driver anyway. So if a user
tried to bind two umems to the same queue, the driver would say
no. But if copy-mode was first enabled and then zero-copy mode (or the
reverse order), we mistakenly enabled both of them on the same umem
leading to buggy behavior. The main culprit for this is that we did
not store the association of umem to queue id in the copy case and
only relied on the driver reporting this. As this relation was not
stored in the driver for copy mode (it does not rely on the AF_XDP
NDOs), this obviously could not work.
This patch fixes the problem by always recording the umem to queue id
relationship in the netdev_queue and netdev_rx_queue structs. This way
we always know what kind of umem has been bound to a queue id and can
act appropriately at bind time.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
These references to the umem will be used to store information
on what kind of AF_XDP umem that is bound to a queue id, if any.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Move the attribute parsing from neigh_dump_table to neigh_dump_info, and
pass the filter arguments down to neigh_dump_table in a new struct. Add
the filter option to proxy neigh dumps as well to make them consistent.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we use raw socket as the vhost backend, a packet from virito with
gso offloading information, cannot be sent out in later validaton at
xmit path, as we did not set correct skb->protocol which is further used
for looking up the gso function.
To fix this, we set this field according to virito hdr information.
Fixes: e858fae2b0b8f4 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Jianfeng Tan <jianfeng.tan@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Ahern says:
====================
net: Consolidate metrics handling for ipv4 and ipv6
As part of the IPv6 fib info refactoring, the intent was to make metrics
handling for ipv6 identical to ipv4. One oversight in ip6_dst_destroy
led to confusion and a couple of incomplete attempts at finding and
fixing the resulting memory leak which was ultimately resolved by
ce7ea4af0838 ("ipv6: fix memory leak on dst->_metrics").
Refactor metrics hanlding make the code really identical for v4 and v6,
and add a few test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ipv4 and ipv6 test cases for metrics (mtu) when fib entries are
created. Can be used with kmemleak to see leaks with both fib entries
and dst_entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the refcounting and potential free of dst metrics associated
for ipv4 and ipv6 to a common helper.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv4 and ipv6 both use refcounted metrics if FIB entries have metrics set.
Move the common initialization code to a helper and use for both protocols.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the refcounting and potential free of dst metrics associated
with a fib entry to a helper and use it in both ipv4 and ipv6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Consolidate initialization of ipv4 and ipv6 metrics when fib entries
are created into a single helper, ip_fib_metrics_init, that handles
the call to ip_metrics_convert.
If no metrics are defined for the fib entry, then the metrics is set
to dst_default_metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Load the respective NAT helper module if the flow uses it.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcf_block_dev() doesn't seem to be used anywhere in the tree.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
bnxt_en: Misc. bug fixes.
4 small bug fixes related to setting firmware message enables bits, possible
memory leak when probe fails, and ring accouting when RDMA driver is loaded.
Please queue these for -stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.
If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.
Fixes: 30f529473ec9 ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0ff ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dave writes:
"amdgpu and two core fixes
Two fixes for amdgpu:
one corrects a use of process->mm
one fix for display code race condition that can result in a crash
Two core fixes:
One for a use-after-free in the leasing code
One for a cma/fbdev crash."
* tag 'drm-fixes-2018-10-05' of git://anongit.freedesktop.org/drm/drm:
drm/amdkfd: Fix incorrect use of process->mm
drm/amd/display: Signal hw_done() after waiting for flip_done()
drm/cma-helper: Fix crash in fbdev error path
drm: fix use-after-free read in drm_mode_create_lease_ioctl()
|
|
into drm-fixes
- Fix an ordering issue in DC with respect to atomic flips that could result
in a crash
- Fix incorrect use of process->mm in KFD
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538668374-22334-1-git-send-email-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v4.19-rc7:
- Fix use-after-free in drm_mode_create_lease_ioctl()
- Fix crash in fbdev error path.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/13b2c3ac-9a96-710e-ceb9-890af164f10e@linux.intel.com
|
|
Fix a simple typo: Completetion -> Completion
Signed-off-by: Konrad Djimeli <kdjimeli@igalia.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
team's ndo_add_slave() acquires 'team->lock' and later tries to open the
newly enslaved device via dev_open(). This emits a 'NETDEV_UP' event
that causes the VLAN driver to add VLAN 0 on the team device. team's
ndo_vlan_rx_add_vid() will also try to acquire 'team->lock' and
deadlock.
Fix this by checking early at the enslavement function that a team
device is not being enslaved to itself.
A similar check was added to the bond driver in commit 09a89c219baf
("bonding: disallow enslaving a bond to itself").
WARNING: possible recursive locking detected
4.18.0-rc7+ #176 Not tainted
--------------------------------------------
syz-executor4/6391 is trying to acquire lock:
(____ptrval____) (&team->lock){+.+.}, at: team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
but task is already holding lock:
(____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&team->lock);
lock(&team->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by syz-executor4/6391:
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:77 [inline]
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x412/0xc30 net/core/rtnetlink.c:4662
#1: (____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947
stack backtrace:
CPU: 1 PID: 6391 Comm: syz-executor4 Not tainted 4.18.0-rc7+ #176
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_deadlock_bug kernel/locking/lockdep.c:1765 [inline]
check_deadlock kernel/locking/lockdep.c:1809 [inline]
validate_chain kernel/locking/lockdep.c:2405 [inline]
__lock_acquire.cold.64+0x1fb/0x486 kernel/locking/lockdep.c:3435
lock_acquire+0x1e4/0x540 kernel/locking/lockdep.c:3924
__mutex_lock_common kernel/locking/mutex.c:757 [inline]
__mutex_lock+0x176/0x1820 kernel/locking/mutex.c:894
mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:909
team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
vlan_add_rx_filter_info+0x14a/0x1d0 net/8021q/vlan_core.c:210
__vlan_vid_add net/8021q/vlan_core.c:278 [inline]
vlan_vid_add+0x63e/0x9d0 net/8021q/vlan_core.c:308
vlan_device_event.cold.12+0x2a/0x2f net/8021q/vlan.c:381
notifier_call_chain+0x180/0x390 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1735
call_netdevice_notifiers net/core/dev.c:1753 [inline]
dev_open+0x173/0x1b0 net/core/dev.c:1433
team_port_add drivers/net/team/team.c:1219 [inline]
team_add_slave+0xa8b/0x1c30 drivers/net/team/team.c:1948
do_set_master+0x1c9/0x220 net/core/rtnetlink.c:2248
do_setlink+0xba4/0x3e10 net/core/rtnetlink.c:2382
rtnl_setlink+0x2a9/0x400 net/core/rtnetlink.c:2636
rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4665
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2455
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4683
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
netlink_sendmsg+0xa18/0xfd0 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:642 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:652
___sys_sendmsg+0x7fd/0x930 net/socket.c:2126
__sys_sendmsg+0x11d/0x290 net/socket.c:2164
__do_sys_sendmsg net/socket.c:2173 [inline]
__se_sys_sendmsg net/socket.c:2171 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2171
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x456b29
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f9706bf8c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f9706bf96d4 RCX: 0000000000456b29
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000004
RBP: 00000000009300a0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d3548 R14: 00000000004c8227 R15: 0000000000000000
Fixes: 87002b03baab ("net: introduce vlan_vid_[add/del] and use them instead of direct [add/kill]_vid ndo calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-and-tested-by: syzbot+bd051aba086537515cdb@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Michal remaind, we should allow to clear ttl inherit. Then we will
have three states:
1. set the flag, and do ttl inherit.
2. do not set the flag, use configured ttl value, or default ttl (0) if
not set.
3. disable ttl inherit, use previous configured ttl value, or default ttl (0).
Fixes: 52d0d404d39dd ("geneve: add ttl inherit support")
CC: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This traffic scheduler allows traffic classes states (transmission
allowed/not allowed, in the simplest case) to be scheduled, according
to a pre-generated time sequence. This is the basis of the IEEE
802.1Qbv specification.
Example configuration:
tc qdisc replace dev enp3s0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
base-time 1528743495910289987 \
sched-entry S 01 300000 \
sched-entry S 02 300000 \
sched-entry S 04 300000 \
clockid CLOCK_TAI
The configuration format is similar to mqprio. The main difference is
the presence of a schedule, built by multiple "sched-entry"
definitions, each entry has the following format:
sched-entry <CMD> <GATE MASK> <INTERVAL>
The only supported <CMD> is "S", which means "SetGateStates",
following the IEEE 802.1Qbv-2015 definition (Table 8-6). <GATE MASK>
is a bitmask where each bit is a associated with a traffic class, so
bit 0 (the least significant bit) being "on" means that traffic class
0 is "active" for that schedule entry. <INTERVAL> is a time duration
in nanoseconds that specifies for how long that state defined by <CMD>
and <GATE MASK> should be held before moving to the next entry.
This schedule is circular, that is, after the last entry is executed
it starts from the first one, indefinitely.
The other parameters can be defined as follows:
- base-time: specifies the instant when the schedule starts, if
'base-time' is a time in the past, the schedule will start at
base-time + (N * cycle-time)
where N is the smallest integer so the resulting time is greater
than "now", and "cycle-time" is the sum of all the intervals of the
entries in the schedule;
- clockid: specifies the reference clock to be used;
The parameters should be similar to what the IEEE 802.1Q family of
specification defines.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cancel pending work before freeing smsc75xx private data structure
during binding. This fixes the following crash in the driver:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: mutex_lock+0x2b/0x3f
<snipped>
Workqueue: events smsc75xx_deferred_multicast_write [smsc75xx]
task: ffff8caa83e85700 task.stack: ffff948b80518000
RIP: 0010:mutex_lock+0x2b/0x3f
<snipped>
Call Trace:
smsc75xx_deferred_multicast_write+0x40/0x1af [smsc75xx]
process_one_work+0x18d/0x2fc
worker_thread+0x1a2/0x269
? pr_cont_work+0x58/0x58
kthread+0xfa/0x10a
? pr_cont_work+0x58/0x58
? rcu_read_unlock_sched_notrace+0x48/0x48
ret_from_fork+0x22/0x40
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vasundhara Volam says:
====================
bnxt_en: devlink param updates
This patchset adds support for 3 generic and 1 driver-specific devlink
parameters. Add documentation for these configuration parameters.
Also, this patchset adds support to return proper error code if
HWRM_NVM_GET/SET_VARIABLE commands return error code
HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED.
v3->v4:
-Remove extra definition of NVM_OFF_HW_TC_OFFLOAD from bnxt_devlink.h
-Remove type information for generic parameters from
devlink-params-bnxt.txt
v2->v3:
-Remove description of generic parameters from devlink-params-bnxt.txt
v1->v2:
-Remove hw_tc_offload parameter.
-Update all patches with Cc of MAINTAINERS.
-Add more description in commit message for device specific parameter.
-Add a new Documentation/networking/devlink-params.txt with some
generic devlink parameters information.
-Add a new Documentation/networking/devlink-params-bnxt.txt with devlink
parameters information that are supported by bnxt_en driver.
====================
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new file to add information about configuration
parameters that are supported by bnxt_en driver via devlink.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new file to add information about some of the
generic configuration parameters set via devlink.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds following driver-specific permanent mode boolean
parameter.
gre_ver_check - Generic Routing Encapsulation(GRE) version check
will be enabled in the device. If disabled, device skips version
checking for GRE packets.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for following generic permanent mode
devlink parameters. They can be modified using devlink param
commands.
msix_vec_per_pf_max - This param sets the number of MSIX vectors
that the device requests from the host on driver initialization.
This value is set in the device which limits MSIX vectors per PF.
msix_vec_per_pf_min - This param sets the number of minimal MSIX
vectors required for the device initialization. Value 0 indicates
a default value is selected. This value is set in the device which
limits MSIX vectors per PF.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED
Return proper error code when Firmware returns
HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED for HWRM_NVM_GET/SET_VARIABLE
commands.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for ignore_ari generic permanent mode
devlink parameter. This parameter is disabled by default. It can be
enabled using devlink param commands.
ignore_ari - If enabled, device ignores ARI(Alternate Routing ID)
capability, even when platforms has the support and creates same number
of partitions when platform does not support ARI capability.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
msix_vec_per_pf_min - This param sets the number of minimal MSIX
vectors required for the device initialization. This value is set
in the device which limits MSIX vectors per PF.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
msix_vec_per_pf_max - This param sets the number of MSIX vectors
that the device requests from the host on driver initialization.
This value is set in the device which is applicable per PF.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
