| Age | Commit message (Collapse) | Author |
|---|
|
Per previous change downgrade all NIC drivers (discrete, embedded,
SoC components, virtual) which don't report test results to CI
from Supported to Maintained.
Also include all components or building blocks of NIC drivers
(separate entries for "shared" code, subsystem support like PTP
or entries for specific offloads etc.)
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20250111024359.3678956-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As announced back in April, require running upstream tests
to maintain Supported status for NIC drivers:
https://lore.kernel.org/20240425114200.3effe773@kernel.org
Multiple vendors have been "working on it" for months.
Let's make it official.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250111024359.3678956-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp fix from Kees Cook:
"Fix a randconfig failure:
- Unconditionally define stub for !CONFIG_SECCOMP (Linus Walleij)"
* tag 'seccomp-v6.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: Stub for !CONFIG_SECCOMP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Fix E825 initialization
Grzegorz Nitka says:
E825 products have incorrect initialization procedure, which may lead to
initialization failures and register values.
Fix E825 products initialization by adding correct sync delay, checking
the PHY revision only for current PHY and adding proper destination
device when reading port/quad.
In addition, E825 uses PF ID for indexing per PF registers and as
a primary PHY lane number, which is incorrect.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Add correct PHY lane assignment
ice: Fix ETH56G FC-FEC Rx offset value
ice: Fix quad registers read on E825
ice: Fix E825 initialization
====================
Link: https://patch.msgid.link/20250113182840.3564250-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Matthieu Baerts says:
====================
mptcp: fixes for connect selftest flakes
Last week, Jakub reported [1] that the MPTCP Connect selftest was
unstable. It looked like it started after the introduction of some fixes
[2]. After analysis from Paolo, these patches revealed existing bugs,
that should be fixed by the following patches.
- Patch 1: Make sure ACK are sent when MPTCP-level window re-opens. In
some corner cases, the other peer was not notified when more data
could be sent. A fix for v5.11, but depending on a feature introduced
in v5.19.
- Patch 2: Fix spurious wake-up under memory pressure. In this
situation, the userspace could be invited to read data not being there
yet. A fix for v6.7.
- Patch 3: Fix a false positive error when running the MPTCP Connect
selftest with the "disconnect" cases. The userspace could disconnect
the socket too soon, which would reset (MP_FASTCLOSE) the connection,
interpreted as an error by the test. A fix for v5.17.
Link: https://lore.kernel.org/20250107131845.5e5de3c5@kernel.org [1]
Link: https://lore.kernel.org/20241230-net-mptcp-rbuf-fixes-v1-0-8608af434ceb@kernel.org [2]
====================
Link: https://patch.msgid.link/20250113-net-mptcp-connect-st-flakes-v1-0-0d986ee7b1b6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The disconnect test-case generates spurious errors:
INFO: disconnect
INFO: extra options: -I 3 -i /tmp/tmp.r43niviyoI
01 ns1 MPTCP -> ns1 (10.0.1.1:10000 ) MPTCP (duration 140ms) [FAIL]
file received by server does not match (in, out):
Unexpected revents: POLLERR/POLLNVAL(19)
-rw-r--r-- 1 root root 10028676 Jan 10 10:47 /tmp/tmp.r43niviyoI.disconnect
Trailing bytes are:
��\����R���!8��u2��5N%
-rw------- 1 root root 9992290 Jan 10 10:47 /tmp/tmp.Os4UbnWbI1
Trailing bytes are:
��\����R���!8��u2��5N%
02 ns1 MPTCP -> ns1 (dead:beef:1::1:10001) MPTCP (duration 206ms) [ OK ]
03 ns1 MPTCP -> ns1 (dead:beef:1::1:10002) TCP (duration 31ms) [ OK ]
04 ns1 TCP -> ns1 (dead:beef:1::1:10003) MPTCP (duration 26ms) [ OK ]
[FAIL] Tests of the full disconnection have failed
Time: 2 seconds
The root cause is actually in the user-space bits: the test program
currently disconnects as soon as all the pending data has been spooled,
generating an FASTCLOSE. If such option reaches the peer before the
latter has reached the closed status, the msk socket will report an
error to the user-space, as per protocol specification, causing the
above failure.
Address the issue explicitly waiting for all the relevant sockets to
reach a closed status before performing the disconnect.
Fixes: 05be5e273c84 ("selftests: mptcp: add disconnect tests")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250113-net-mptcp-connect-st-flakes-v1-3-0d986ee7b1b6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The wake-up condition currently implemented by mptcp_epollin_ready()
is wrong, as it could mark the MPTCP socket as readable even when
no data are present and the system is under memory pressure.
Explicitly check for some data being available in the receive queue.
Fixes: 5684ab1a0eff ("mptcp: give rcvlowat some love")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250113-net-mptcp-connect-st-flakes-v1-2-0d986ee7b1b6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mptcp_cleanup_rbuf() is responsible to send acks when the user-space
reads enough data to update the receive windows significantly.
It tries hard to avoid acquiring the subflow sockets locks by checking
conditions similar to the ones implemented at the TCP level.
To avoid too much code duplication - the MPTCP protocol can't reuse the
TCP helpers as part of the relevant status is maintained into the msk
socket - and multiple costly window size computation, mptcp_cleanup_rbuf
uses a rough estimate for the most recently advertised window size:
the MPTCP receive free space, as recorded as at last-ack time.
Unfortunately the above does not allow mptcp_cleanup_rbuf() to detect
a zero to non-zero win change in some corner cases, skipping the
tcp_cleanup_rbuf call and leaving the peer stuck.
After commit ea66758c1795 ("tcp: allow MPTCP to update the announced
window"), MPTCP has actually cheap access to the announced window value.
Use it in mptcp_cleanup_rbuf() for a more accurate ack generation.
Fixes: e3859603ba13 ("mptcp: better msk receive window updates")
Cc: stable@vger.kernel.org
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/20250107131845.5e5de3c5@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250113-net-mptcp-connect-st-flakes-v1-1-0d986ee7b1b6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
tcp: add a new PAWS_ACK drop reason
Current TCP_RFC7323_PAWS drop reason is too generic and can
cause confusion.
One common source for these drops are ACK packets coming too late.
A prior packet with payload already changed tp->rcv_nxt.
Add TCP_RFC7323_PAWS_ACK new drop reason, and do not
generate a DUPACK for such old ACK.
====================
Link: https://patch.msgid.link/20250113135558.3180360-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prior patch in the series added TCP_RFC7323_PAWS_ACK drop reason.
This patch adds the corresponding SNMP counter, for folks
using nstat instead of tracing for TCP diagnostics.
nstat -az | grep PAWSOldAck
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250113135558.3180360-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XPS can cause reorders because of the relaxed OOO
conditions for pure ACK packets.
For hosts not using RFS, what can happpen is that ACK
packets are sent on behalf of the cpu processing NIC
interrupts, selecting TX queue A for ACK packet P1.
Then a subsequent sendmsg() can run on another cpu.
TX queue selection uses the socket hash and can choose
another queue B for packets P2 (with payload).
If queue A is more congested than queue B,
the ACK packet P1 could be sent on the wire after
P2.
A linux receiver when processing P1 (after P2) currently increments
LINUX_MIB_PAWSESTABREJECTED (TcpExtPAWSEstab)
and use TCP_RFC7323_PAWS drop reason.
It might also send a DUPACK if not rate limited.
In order to better understand this pattern, this
patch adds a new drop_reason : TCP_RFC7323_PAWS_ACK.
For old ACKS like these, we no longer increment
LINUX_MIB_PAWSESTABREJECTED and no longer sends a DUPACK,
keeping credit for other more interesting DUPACK.
perf record -e skb:kfree_skb -a
perf script
...
swapper 0 [148] 27475.438637: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [208] 27475.438706: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [208] 27475.438908: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [148] 27475.439010: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [148] 27475.439214: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [208] 27475.439286: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20250113135558.3180360-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Following patch is adding a new drop_reason to tcp_validate_incoming().
Change tcp_disordered_ack() to not return a boolean anymore,
but a drop reason.
Change its name to tcp_disordered_ack_check()
Refactor tcp_validate_incoming() to ease the code
review of the following patch, and reduce indentation
level.
This patch is a refactor, with no functional change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20250113135558.3180360-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a typo in a phydev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250113091555.23594-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is possible to enable few cpufreq drivers, without the framework
being enabled. This happened due to a bug while moving the entries
earlier. Fix it.
Fixes: 7ee1378736f0 ("cpufreq: Move CPPC configs to common Kconfig and add RISC-V")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://patch.msgid.link/84ac7a8fa72a8fe20487bb0a350a758bce060965.1736488384.git.viresh.kumar@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Prevent bwctrl NULL pointer dereference that caused hangs on shutdown
on ASUS ROG Strix SCAR 17 G733PYV (Lukas Wunner)
* tag 'pci-v6.13-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/bwctrl: Fix NULL pointer deref on unbind and bind
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Tariq Toukan says:
====================
mlx5-next updates 2025-01-14
The following pull-request contains mlx5 IFC updates.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Add nic_cap_reg and vhca_icm_ctrl registers
net/mlx5: SHAMPO: Introduce new SHAMPO specific HCA caps
net/mlx5: Add support for MRTCQ register
net/mlx5: Update mlx5_ifc to support FEC for 200G per lane link modes
====================
Link: https://patch.msgid.link/20250114055700.1928736-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One iscsi driver fix and one core fix.
The core fix is an important one because a retry efficiency update is
now causing some USB devices to get the wrong size on discovery (it
upset their retry logic for READ_CAPACITY_16)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: Fix redundant response for ISCSI_UEVENT_GET_HOST_STATS request
scsi: core: Fix command pass through retry regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the last PR for 6.13. This became bigger than wished due to
the timing after holiday breaks.
The only large LOC is the additional document for Cirrus codec which
is nice for users (and absolutely safe). All the rest are small fixes
in ASoC Rcar and codecs as well as HD-audio quirks (And no fix for USB
guitar pedals seen yet :)"
* tag 'sound-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Fix volume adjustment issue on Lenovo ThinkBook 16P Gen5
ALSA: hda/realtek: fixup ASUS H7606W
ALSA: hda/realtek: fixup ASUS GA605W
ALSA: hda/realtek: Add support for Ayaneo System using CS35L41 HDA
ASoC: rsnd: check rsnd_adg_clk_enable() return value
ASoC: cs42l43: Add codec force suspend/resume ops
ALSA: doc: Add codecs/index.rst to top-level index
ALSA: doc: cs35l56: Add information about Cirrus Logic CS35L54/56/57
ASoC: samsung: Add missing depends on I2C
MAINTAINERS: add missing maintainers for Simple Audio Card
ASoC: samsung: Add missing selects for MFD_WM8994
ASoC: codecs: es8316: Fix HW rate calculation for 48Mhz MCLK
ASoC: wm8994: Add depends on MFD core
ASoC: tas2781: Fix occasional calibration failture
ASoC: codecs: ES8326: Adjust ANA_MICBIAS to reduce pop noise
|
|
Kory Maincent says:
====================
Arrange PSE core and update TPS23881 driver
This patch includes several improvements to the PSE core for better
implementation and maintainability:
- Move the conversion between current limit and power limit from the driver
to the PSE core.
- Update power and current limit checks.
- Split the ethtool_get_status callback into multiple callbacks.
- Fix PSE PI of_node detection.
- Clean ethtool header of PSE structures.
Additionally, the TPS23881 driver has been updated to support power
limit and measurement features, aligning with the new PSE core
functionalities.
This patch series is the first part of the budget evaluation strategy
support patch series sent earlier:
https://lore.kernel.org/netdev/20250104161622.7b82dfdf@kmaincent-XPS-13-7390/T/#t
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
====================
Link: https://patch.msgid.link/20250110-b4-feature_poe_arrange-v3-0-142279aedb94@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove PSE-specific structures from the ethtool header to improve code
modularity, maintain independent headers, and reduce incremental build
time.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The PI of_node was not assigned in the regulator_config structure, leading
to failures in resolving the correct supply when different power supplies
are assigned to multiple PIs of a PSE controller. This fix ensures that the
of_node is properly set in the regulator_config, allowing accurate supply
resolution for each PI.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Expand PSE callbacks to support the newly introduced
pi_get/set_pw_limit() and pi_get_voltage() functions. These callbacks
allow for power limit configuration in the TPS23881 controller.
Additionally, the patch includes the pi_get_pw_class() the
pi_get_actual_pw(), and the pi_get_pw_limit_ranges') callbacks providing
more comprehensive PoE status reporting.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The is_enabled callback is now redundant as the admin_state can be obtained
directly from the driver and provides the same information.
To simplify functionality, the core will handle this internally, making
the is_enabled callback unnecessary at the driver level. Remove the
callback from all drivers.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ethtool_get_status callback currently handles all status and PSE
information within a single function. This approach has two key
drawbacks:
1. If the core requires some information for purposes other than
ethtool_get_status, redundant code will be needed to fetch the same
data from the driver (like is_enabled).
2. Drivers currently have access to all information passed to ethtool.
New variables will soon be added to ethtool status, such as PSE ID,
power domain IDs, and budget evaluation strategies, which are meant
to be managed solely by the core. Drivers should not have the ability
to modify these variables.
To resolve these issues, ethtool_get_status has been split into multiple
callbacks, with each handling a specific piece of information required
by ethtool or the core.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The regulator framework uses current limits, but the PSE standard and
known PSE controllers rely on power limits. Instead of converting
current to power within each driver, perform the conversion in the PSE
core. This avoids redundancy in driver implementation and aligns better
with the standard, simplifying driver development.
Remove at the same time the _pse_ethtool_get_status() function which is
not needed anymore.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When setting the PWOFF register, the controller resets multiple
configuration registers. This patch ensures these registers are
reconfigured as needed following a disable operation.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This driver frequently follows a pattern where two registers are read or
written in a single operation, followed by calculating the bit offset for
a specific channel.
Introduce helpers to streamline this process and reduce code redundancy,
making the codebase cleaner and more maintainable.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cleaned up several functions in tps23881 by removing redundant checks on
return values at the end of functions. These check has been removed, and
the return statement now directly returns the function result, reducing
the code's complexity and making it more concise.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Kyle Swenson <kyle.swenson@est.tech>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Checking only the current limit is not sufficient. According to the
standard, voltage can reach up to 57V and current up to 1.92A, which
exceeds the power limit described in the standard (99.9W). Add a power
limit check to prevent this.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Setting the max_uA constraint in the regulator API imposes a current
limit during the regulator registration process. This behavior conflicts
with preserving the maximum PI power budget configuration across reboots.
Instead, compare the desired current limit to MAX_PI_CURRENT in the
pse_pi_set_current_limit() function to ensure proper handling of the
power budget.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Removed the unused pse_ethtool_get_pw_limit() function declaration from
pse.h. This function was declared but never implemented or used,
making the declaration unnecessary.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Kyle Swenson <kyle.swenson@est.tech>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Stefano Garzarella says:
====================
vsock: some fixes due to transport de-assignment
v1: https://lore.kernel.org/netdev/20250108180617.154053-1-sgarzare@redhat.com/
v2:
- Added patch 3 to cancel the virtio close delayed work when de-assigning
the transport
- Added patch 4 to clean the socket state after de-assigning the transport
- Added patch 5 as suggested by Michael and Hyunwoo Kim. It's based on
Hyunwoo Kim and Wongi Lee patch [1] but using WARN_ON and covering more
functions
- Added R-b/T-b tags
This series includes two patches discussed in the thread started by
Hyunwoo Kim a few weeks ago [1], plus 3 more patches added after some
discussions on v1 (see changelog). All related to the case where a vsock
socket is de-assigned from a transport (e.g., because the connect fails
or is interrupted by a signal) and then assigned to another transport
or to no-one (NULL).
I tested with usual vsock test suite, plus Michal repro [2]. (Note: the repo
works only if a G2H transport is not loaded, e.g. virtio-vsock driver).
The first patch is a fix more appropriate to the problem reported in
that thread, the second patch on the other hand is a related fix but
of a different problem highlighted by Michal Luczaj. It's present only
in vsock_bpf and already handled in af_vsock.c
The third patch is to cancel the virtio close delayed work when de-assigning
the transport, the fourth patch is to clean the socket state after de-assigning
the transport, the last patch adds warnings and prevents null-ptr-deref in
vsock_*[has_data|has_space].
Hyunwoo Kim, Michal, if you can test and report your Tested-by that
would be great!
[1] https://lore.kernel.org/netdev/Z2K%2FI4nlHdfMRTZC@v4bel-B760M-AORUS-ELITE-AX/
[2] https://lore.kernel.org/netdev/2b3062e3-bdaa-4c94-a3c0-2930595b9670@rbox.co/
====================
Link: https://patch.msgid.link/20250110083511.30419-1-sgarzare@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Recent reports have shown how we sometimes call vsock_*_has_data()
when a vsock socket has been de-assigned from a transport (see attached
links), but we shouldn't.
Previous commits should have solved the real problems, but we may have
more in the future, so to avoid null-ptr-deref, we can return 0
(no space, no data available) but with a warning.
This way the code should continue to run in a nearly consistent state
and have a warning that allows us to debug future problems.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/netdev/Z2K%2FI4nlHdfMRTZC@v4bel-B760M-AORUS-ELITE-AX/
Link: https://lore.kernel.org/netdev/5ca20d4c-1017-49c2-9516-f6f75fd331e9@rbox.co/
Link: https://lore.kernel.org/netdev/677f84a8.050a0220.25a300.01b3.GAE@google.com/
Co-developed-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Co-developed-by: Wongi Lee <qwerty@theori.io>
Signed-off-by: Wongi Lee <qwerty@theori.io>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Reviewed-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Transport's release() and destruct() are called when de-assigning the
vsock transport. These callbacks can touch some socket state like
sock flags, sk_state, and peer_shutdown.
Since we are reassigning the socket to a new transport during
vsock_connect(), let's reset these fields to have a clean state with
the new transport.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Cc: stable@vger.kernel.org
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
During virtio_transport_release() we can schedule a delayed work to
perform the closing of the socket before destruction.
The destructor is called either when the socket is really destroyed
(reference counter to zero), or it can also be called when we are
de-assigning the transport.
In the former case, we are sure the delayed work has completed, because
it holds a reference until it completes, so the destructor will
definitely be called after the delayed work is finished.
But in the latter case, the destructor is called by AF_VSOCK core, just
after the release(), so there may still be delayed work scheduled.
Refactor the code, moving the code to delete the close work already in
the do_close() to a new function. Invoke it during destruction to make
sure we don't leave any pending work.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Cc: stable@vger.kernel.org
Reported-by: Hyunwoo Kim <v4bel@theori.io>
Closes: https://lore.kernel.org/netdev/Z37Sh+utS+iV3+eb@v4bel-B760M-AORUS-ELITE-AX/
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Tested-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some of the core functions can only be called if the transport
has been assigned.
As Michal reported, a socket might have the transport at NULL,
for example after a failed connect(), causing the following trace:
BUG: kernel NULL pointer dereference, address: 00000000000000a0
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 12faf8067 P4D 12faf8067 PUD 113670067 PMD 0
Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 15 UID: 0 PID: 1198 Comm: a.out Not tainted 6.13.0-rc2+
RIP: 0010:vsock_connectible_has_data+0x1f/0x40
Call Trace:
vsock_bpf_recvmsg+0xca/0x5e0
sock_recvmsg+0xb9/0xc0
__sys_recvfrom+0xb3/0x130
__x64_sys_recvfrom+0x20/0x30
do_syscall_64+0x93/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
So we need to check the `vsk->transport` in vsock_bpf_recvmsg(),
especially for connected sockets (stream/seqpacket) as we already
do in __vsock_connectible_recvmsg().
Fixes: 634f1a7110b4 ("vsock: support sockmap")
Cc: stable@vger.kernel.org
Reported-by: Michal Luczaj <mhal@rbox.co>
Closes: https://lore.kernel.org/netdev/5ca20d4c-1017-49c2-9516-f6f75fd331e9@rbox.co/
Tested-by: Michal Luczaj <mhal@rbox.co>
Reported-by: syzbot+3affdbfc986ecd9200fd@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/677f84a8.050a0220.25a300.01b3.GAE@google.com/
Tested-by: syzbot+3affdbfc986ecd9200fd@syzkaller.appspotmail.com
Reviewed-by: Hyunwoo Kim <v4bel@theori.io>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If the socket has been de-assigned or assigned to another transport,
we must discard any packets received because they are not expected
and would cause issues when we access vsk->transport.
A possible scenario is described by Hyunwoo Kim in the attached link,
where after a first connect() interrupted by a signal, and a second
connect() failed, we can find `vsk->transport` at NULL, leading to a
NULL pointer dereference.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Cc: stable@vger.kernel.org
Reported-by: Hyunwoo Kim <v4bel@theori.io>
Reported-by: Wongi Lee <qwerty@theori.io>
Closes: https://lore.kernel.org/netdev/Z2LvdTTQR7dBmPb5@v4bel-B760M-AORUS-ELITE-AX/
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
MD Danish Anwar says:
====================
Add Multicast Filtering support for VLAN interface
This series adds Multicast filtering support for VLAN interfaces in dual
EMAC and HSR offload mode for ICSSG driver.
Patch 1/4 - Adds support for VLAN in dual EMAC mode
Patch 2/4 - Adds MC filtering support for VLAN in dual EMAC mode
Patch 3/4 - Create and export hsr_get_port_ndev() in hsr_device.c
Patch 4/4 - Adds MC filtering support for VLAN in HSR mode
[1] https://lore.kernel.org/all/20241216100044.577489-2-danishanwar@ti.com/
[2] https://lore.kernel.org/all/202412210336.BmgcX3Td-lkp@intel.com/#t
[3] https://lore.kernel.org/all/31bb8a3e-5a1c-4c94-8c33-c0dfd6d643fb@kernel.org/
v1 https://lore.kernel.org/all/20241216100044.577489-1-danishanwar@ti.com/
v2 https://lore.kernel.org/all/20241223092557.2077526-1-danishanwar@ti.com/
v3 https://lore.kernel.org/all/20250103092033.1533374-1-danishanwar@ti.com/
====================
Link: https://patch.msgid.link/20250110082852.3899027-1-danishanwar@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add multicast filtering support for VLAN interfaces in HSR offload mode
for ICSSG driver.
The driver calls vlan_for_each() API on the hsr device's ndev to get the
list of available vlans for the hsr device. The driver then sync mc addr of
vlan interface with a locally mainatined list emac->vlan_mcast_list[vid]
using __hw_addr_sync_multiple() API.
The driver then calls the sync / unsync callbacks.
In the sync / unsync call back, driver checks if the vdev's real dev is
hsr device or not. If the real dev is hsr device, driver gets the per
port device using hsr_get_port_ndev() and then driver passes appropriate
vid to FDB helper functions.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Create an API to get the net_device to the slave port of HSR device. The
API will take hsr net_device and enum hsr_port_type for which we want the
net_device as arguments.
This API can be used by client drivers who support HSR and want to get
the net_devcie of slave ports from the hsr device. Export this API for
the same.
This API needs the enum hsr_port_type to be accessible by the drivers using
hsr. Move the enum hsr_port_type from net/hsr/hsr_main.h to
include/linux/if_hsr.h for the same.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add multicast filtering support for VLAN interfaces in dual EMAC mode
for ICSSG driver.
The driver uses vlan_for_each() API to get the list of available
vlans. The driver then sync mc addr of vlan interface with a locally
mainatined list emac->vlan_mcast_list[vid] using __hw_addr_sync_multiple()
API.
__hw_addr_sync_multiple() is used instead of __hw_addr_sync() to sync
vdev->mc with local list because the sync_cnt for addresses in vdev->mc
will already be set by the vlan_dev_set_rx_mode() [net/8021q/vlan_dev.c]
and __hw_addr_sync() only syncs when the sync_cnt == 0. Whereas
__hw_addr_sync_multiple() can sync addresses even if sync_cnt is not 0.
Export __hw_addr_sync_multiple() so that driver can use it.
Once the local list is synced, driver calls __hw_addr_sync_dev() with
the local list, vdev, sync and unsync callbacks.
__hw_addr_sync_dev() is used with the local maintained list as the list
to synchronize instead of using __dev_mc_sync() on vdev because
__dev_mc_sync() on vdev will call __hw_addr_sync_dev() on vdev->mc and
sync_cnt for addresses in vdev->mc will already be set by the
vlan_dev_set_rx_mode() [net/8021q/vlan_dev.c] and __hw_addr_sync_dev()
only syncs if the sync_cnt of addresses in the list (vdev->mc in this case)
is 0. Whereas __hw_addr_sync_dev() on local list will work fine as the
sync_cnt for addresses in the local list will still be 0.
Based on change in addresses in the local list, sync / unsync callbacks
are invoked. In the sync / unsync API in driver, based on whether the ndev
is vlan or not, driver passes appropriate vid to FDB helper functions.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for VLAN filtering in dual EMAC mode.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a small batch of Netfilter/IPVS updates
for net-next:
1) Remove unused genmask parameter in nf_tables_addchain()
2) Speed up reads from /proc/net/ip_vs_conn, from Florian Westphal.
3) Skip empty buckets in hashlimit to avoid atomic operations that results
in false positive reports by syzbot with lockdep enabled, patch from
Eric Dumazet.
4) Add conntrack event timestamps available via ctnetlink,
from Florian Westphal.
netfilter pull request 25-01-11
* tag 'nf-next-25-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: conntrack: add conntrack event timestamp
netfilter: xt_hashlimit: htable_selective_cleanup() optimization
ipvs: speed up reads from ip_vs_conn proc file
netfilter: nf_tables: remove the genmask parameter
====================
Link: https://patch.msgid.link/20250111230800.67349-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Oleksij Rempel says:
====================
Introduce unified and structured PHY
This patch set introduces a unified and well-structured interface for
reporting PHY statistics. Instead of relying on arbitrary strings in PHY
drivers, this interface provides a consistent and structured way to
expose PHY statistics to userspace via ethtool.
The initial groundwork for this effort was laid by Jakub Kicinski, who
contributed patches to plumb PHY statistics to drivers and added support
for structured statistics in ethtool. Building on Jakub's work, I tested
the implementation with several PHYs, addressed a few issues, and added
support for statistics in two specific PHY drivers.
Most of changes are tracked in separate patches.
changes v6:
- drop ethtool_stat_add patch
changes v5:
- rebase against latest net-next
====================
Link: https://patch.msgid.link/20250110060517.711683-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for reporting PHY statistics in the DP83TG720 driver. This
includes cumulative tracking of link loss events, transmit/receive
packet counts, and error counts. Implemented functions to update and
provide statistics via ethtool, with optional polling support enabled
through `PHY_POLL_STATS`.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for reporting PHY statistics in the DP83TD510 driver. This
includes cumulative tracking of transmit/receive packet counts, and
error counts. Implemented functions to update and provide statistics via
ethtool, with optional polling support enabled through `PHY_POLL_STATS`.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add an optional polling interface for PHY statistics to simplify driver
implementation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
pair guide
Replace generic instructions for monitoring error counters with a
procedure using the unified PHY statistics interface (`--all-groups`).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce a new way to report PHY statistics in a structured and
standardized format using the netlink API. This new method does not
replace the old driver-specific stats, which can still be accessed with
`ethtool -S <eth name>`. The structured stats are available with
`ethtool -S <eth name> --all-groups`.
This new method makes it easier to diagnose problems by organizing stats
in a consistent and documented way.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce support for standardized PHY statistics reporting in ethtool
by extending the PHYLIB framework. Add the functions
phy_ethtool_get_phy_stats() and phy_ethtool_get_link_ext_stats() to
provide a consistent interface for retrieving PHY-level and
link-specific statistics. These functions are used within the ethtool
implementation to avoid direct access to the phy_device structure
outside of the PHYLIB framework.
A new structure, ethtool_phy_stats, is introduced to standardize PHY
statistics such as packet counts, byte counts, and error counters.
Drivers are updated to include callbacks for retrieving PHY and
link-specific statistics, ensuring values are explicitly set only for
supported fields, initialized with ETHTOOL_STAT_NOT_SET to avoid
ambiguity.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
