| Age | Commit message (Collapse) | Author |
|---|
|
When RoCE is enabled on a given L2 interface, the interrupt lines
are divided equally between L2 and RoCE -
But in case number of lines needed for RoCE is limited by number
of available CNQs, we can utilize the additional lines for L2.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Management firmware and driver are meant to be both backward and forward
compatibile with each other.
If a new mangement firmware would work with an older driver,
it's possible that driver would receive indications which are meaningless
to it. That's perfectly acceptible from the firmware part - so no need to
log such messages at default verbosity; That would only serve to confuse
users.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The management firmware is running on a Big Endian processor,
and when running on LE platform HW is configured to swap access
to memory shared between management firmware and driver on
32-bit granulariy.
As a result, for matters of simplicity most of the APIs between
driver and management firmware are based on 32-bit variables.
MAC settings are one exception, as driver needs to fill a byte
array when indicating to management firmware that primary MAC
has changed.
Due to the swap, driver must make sure that the mac that was
provided in byte-order would be translated into native order,
otherwise after the swap the management firmware would read
it swapped.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver interaction with management firmware involves a union
of all the data-members relating to the commands the driver prepares.
Current interface assumes the caller always passes such a union -
but thats cumbersome as well as risky [chancing a stack corruption
in case caller accidentally passes a smaller member instead of union].
Change implementation so that caller could pass a pointer to any
of the members instead of the union.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interaction of driver -> management firmware is based
on a one-pending mailbox [per interface], and various
mailbox commands need to be synchronized.
Current scheme is messy, and there's a difficulty extending
it as it deals differently with various commands as well as
making assumption on the required behavior for load/unload
requests.
Drop the current scheme into a completion-list-based approach;
Each flow would try sending the command when possible,
allowing one flow to complete another flow's completion and
relieve the mailbox before sending its own command.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Zygo tracked down a very old bug with inline compressed extents.
I didn't tag this one for stable because I want to do individual
tested backports. It's a little tricky and I'd rather do some extra
testing on it along the way"
* 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: add missing memset while reading compressed inline extents
Btrfs: fix regression in lock_delalloc_pages
btrfs: remove btrfs_err_str function from uapi/linux/btrfs.h
|
|
Pull networking fixes from David Miller:
1) Several netfilter fixes from Pablo and the crew:
- Handle fragmented packets properly in netfilter conntrack, from
Florian Westphal.
- Fix SCTP ICMP packet handling, from Ying Xue.
- Fix big-endian bug in nftables, from Liping Zhang.
- Fix alignment of fake conntrack entry, from Steven Rostedt.
2) Fix feature flags setting in fjes driver, from Taku Izumi.
3) Openvswitch ipv6 tunnel source address not set properly, from Or
Gerlitz.
4) Fix jumbo MTU handling in amd-xgbe driver, from Thomas Lendacky.
5) sk->sk_frag.page not released properly in some cases, from Eric
Dumazet.
6) Fix RTNL deadlocks in nl80211, from Johannes Berg.
7) Fix erroneous RTNL lockdep splat in crypto, from Herbert Xu.
8) Cure improper inflight handling during AF_UNIX GC, from Andrey
Ulanov.
9) sch_dsmark doesn't write to packet headers properly, from Eric
Dumazet.
10) Fix SCM_TIMESTAMPING_OPT_STATS handling in TCP, from Soheil Hassas
Yeganeh.
11) Add some IDs for Motorola qmi_wwan chips, from Tony Lindgren.
12) Fix nametbl deadlock in tipc, from Ying Xue.
13) GRO and LRO packets not counted correctly in mlx5 driver, from Gal
Pressman.
14) Fix reset of internal PHYs in bcmgenet, from Doug Berger.
15) Fix hashmap allocation handling, from Alexei Starovoitov.
16) nl_fib_input() needs stronger netlink message length checking, from
Eric Dumazet.
17) Fix double-free of sk->sk_filter during sock clone, from Daniel
Borkmann.
18) Fix RX checksum offloading in aquantia driver, from Pavel Belous.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
net:ethernet:aquantia: Fix for RX checksum offload.
amd-xgbe: Fix the ECC-related bit position definitions
sfc: cleanup a condition in efx_udp_tunnel_del()
Bluetooth: btqcomsmd: fix compile-test dependency
inet: frag: release spinlock before calling icmp_send()
tcp: initialize icsk_ack.lrcvtime at session start time
genetlink: fix counting regression on ctrl_dumpfamily()
socket, bpf: fix sk_filter use after free in sk_clone_lock
ipv4: provide stronger user input validation in nl_fib_input()
bpf: fix hashmap extra_elems logic
enic: update enic maintainers
net: bcmgenet: remove bcmgenet_internal_phy_setup()
ipv6: make sure to initialize sockc.tsflags before first use
fjes: Do not load fjes driver if extended socket device is not power on.
fjes: Do not load fjes driver if system does not have extended socket device.
net/mlx5e: Count LRO packets correctly
net/mlx5e: Count GSO packets correctly
net/mlx5: Increase number of max QPs in default profile
net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps
net/mlx5e: Use the proper UAPI values when offloading TC vlan actions
...
|
|
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this
via NETIF_F_RXCSUM flag.
v1->v2: 'Signed-off-by' tag added.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stephen Hemminger says:
====================
netvsc: bug fixes and cleanups
These fix NAPI issues and bugs found during testing of shutdown
testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix warning from unused set_complete variable. And rearrange code
to eliminate unnecessary goto's.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since there already is a special case goto for control messages (skb == NULL)
in netvsc_send, there is no need for later checks in same code path.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The channel inbound lock was not being used at all by the netvsc
device, but the spin_lock was helpful by providing necessary
barrier before waiting.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than a lock and variable, use a refcount_t to keep track
of the number of sub channels. Don't need to wait for subchannels
on device removal since wait was already done in device_add.
Also fix the error handling; don't wait forever in case of
an error on request to create sub channels.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is cleaner to use RCU protected pointer (nvdev_ctx->nvdev)
to indicate device is in removed state, rather than having a separate
boolean flag. By using the pointer the context can be checked
by static checkers and dynamic lockdep.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netvsc driver has an internal structure (netvsc_device) which
is created when device is opened and released when device is closed.
And also opened/released when MTU or number of channels change.
Since this is referenced in the receive and transmit path, it is
safer to use RCU to protect/prevent use after free problems.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default number of maximum channels should be limited to the
number of cpus available on the numa node of the primary channel.
This also makes sure maximum channels <= num_online_cpus
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If device is not up, then changing MTU (or number of channels)
should not re-enable the device.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using NAPI, the single stream performance declined signifcantly
because the poll routine was updating host after every burst
of packets. This excess signalling caused host throttling.
This fix restores the old behavior. Host is only signalled
after the ring has been emptied.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are no egress packets pending, then don't look for tx completions
in napi poll. Also, fix broken tx queue wakeup logic.
Signed-off-by: VSR Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add workqueue that is periodically run to try to allocate RX buffers in OOM
conditions in PF and VF.
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Presumably if there is an "add" function, there is also a "del"
function. But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
compile-testing fails when QCOM_SMD is a loadable module:
drivers/bluetooth/built-in.o: In function `btqcomsmd_send':
btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send'
drivers/bluetooth/built-in.o: In function `btqcomsmd_probe':
btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel'
btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata'
This clarifies the dependency to allow compile-testing only when
SMD is completely disabled, otherwise the dependency on QCOM_SMD
will make sure we can link against it.
Fixes: e27ee2b16bad ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Iyappan Subramanian says:
====================
drivers: net: xgene-v2: Add MDIO and ethtool support
This patch set,
- adds phy management and ethtool support
- fixes ethernet reset
- addresses review comments from previous patch set
v2: Address review comments from v1
- removed mdio_lock, since there is a top level lock in mdio_bus.c
v1:
- Initial version
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed review comments from the previous patch-set.
- changed return value check of platform_get_irq() to < 0
- replaced devm_request(free)_irq() calls by request(free)_irq() since
they are called from open() and close()
- changed sizeof(struct mystruct) to sizeof(*mystruct)
- reduced indentation on tx_timeout()
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed port reset sequence by adding ECC init.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added basic ethtool support.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added phy management support by using phy abstraction layer APIs.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Martin KaFai Lau says:
====================
bpf: Add map-in-map support
This patchset adds map-in-map support (map->map).
One use case is the (vips -> webservers) in the L4 load balancer so
that different vips can be backed by different set of webservers.
Please refer to the individual commit log for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test cases for array of maps and hash of maps.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds hash of maps support (hashmap->bpf_map).
BPF_MAP_TYPE_HASH_OF_MAPS is added.
A map-in-map contains a pointer to another map and lets call
this pointer 'inner_map_ptr'.
Notes on deleting inner_map_ptr from a hash map:
1. For BPF_F_NO_PREALLOC map-in-map, when deleting
an inner_map_ptr, the htab_elem itself will go through
a rcu grace period and the inner_map_ptr resides
in the htab_elem.
2. For pre-allocated htab_elem (!BPF_F_NO_PREALLOC),
when deleting an inner_map_ptr, the htab_elem may
get reused immediately. This situation is similar
to the existing prealloc-ated use cases.
However, the bpf_map_fd_put_ptr() calls bpf_map_put() which calls
inner_map->ops->map_free(inner_map) which will go
through a rcu grace period (i.e. all bpf_map's map_free
currently goes through a rcu grace period). Hence,
the inner_map_ptr is still safe for the rcu reader side.
This patch also includes BPF_MAP_TYPE_HASH_OF_MAPS to the
check_map_prealloc() in the verifier. preallocation is a
must for BPF_PROG_TYPE_PERF_EVENT. Hence, even we don't expect
heavy updates to map-in-map, enforcing BPF_F_NO_PREALLOC for map-in-map
is impossible without disallowing BPF_PROG_TYPE_PERF_EVENT from using
map-in-map first.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a few helper funcs to enable map-in-map
support (i.e. outer_map->inner_map). The first outer_map type
BPF_MAP_TYPE_ARRAY_OF_MAPS is also added in this patch.
The next patch will introduce a hash of maps type.
Any bpf map type can be acted as an inner_map. The exception
is BPF_MAP_TYPE_PROG_ARRAY because the extra level of
indirection makes it harder to verify the owner_prog_type
and owner_jited.
Multi-level map-in-map is not supported (i.e. map->map is ok
but not map->map->map).
When adding an inner_map to an outer_map, it currently checks the
map_type, key_size, value_size, map_flags, max_entries and ops.
The verifier also uses those map's properties to do static analysis.
map_flags is needed because we need to ensure BPF_PROG_TYPE_PERF_EVENT
is using a preallocated hashtab for the inner_hash also. ops and
max_entries are needed to generate inlined map-lookup instructions.
For simplicity reason, a simple '==' test is used for both map_flags
and max_entries. The equality of ops is implied by the equality of
map_type.
During outer_map creation time, an inner_map_fd is needed to create an
outer_map. However, the inner_map_fd's life time does not depend on the
outer_map. The inner_map_fd is merely used to initialize
the inner_map_meta of the outer_map.
Also, for the outer_map:
* It allows element update and delete from syscall
* It allows element lookup from bpf_prog
The above is similar to the current fd_array pattern.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix in verifier:
For the same bpf_map_lookup_elem() instruction (i.e. "call 1"),
a broken case is "a different type of map could be used for the
same lookup instruction". For example, an array in one case and a
hashmap in another. We have to resort to the old dynamic call behavior
in this case. The fix is to check for collision on insn_aux->map_ptr.
If there is collision, don't inline the map lookup.
Please see the "do_reg_lookup()" in test_map_in_map_kern.c in the later
patch for how-to trigger the above case.
Simplifications on array_map_gen_lookup():
1. Calculate elem_size from map->value_size. It removes the
need for 'struct bpf_array' which makes the later map-in-map
implementation easier.
2. Remove the 'elem_size == 1' test
Fixes: 81ed18ab3098 ("bpf: add helper inlining infra and optimize map_array lookup")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dmitry reported a lockdep splat [1] (false positive) that we can fix
by releasing the spinlock before calling icmp_send() from ip_expire()
This is a false positive because sending an ICMP message can not
possibly re-enter the IP frag engine.
[1]
[ INFO: possible circular locking dependency detected ]
4.10.0+ #29 Not tainted
-------------------------------------------------------
modprobe/12392 is trying to acquire lock:
(_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] spin_lock
include/linux/spinlock.h:299 [inline]
(_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] __netif_tx_lock
include/linux/netdevice.h:3486 [inline]
(_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>]
sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180
but task is already holding lock:
(&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock
include/linux/spinlock.h:299 [inline]
(&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>]
ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&(&q->lock)->rlock){+.-...}:
validate_chain kernel/locking/lockdep.c:2267 [inline]
__lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340
lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151
spin_lock include/linux/spinlock.h:299 [inline]
ip_defrag+0x3a2/0x4130 net/ipv4/ip_fragment.c:669
ip_check_defrag+0x4e3/0x8b0 net/ipv4/ip_fragment.c:713
packet_rcv_fanout+0x282/0x800 net/packet/af_packet.c:1459
deliver_skb net/core/dev.c:1834 [inline]
dev_queue_xmit_nit+0x294/0xa90 net/core/dev.c:1890
xmit_one net/core/dev.c:2903 [inline]
dev_hard_start_xmit+0x16b/0xab0 net/core/dev.c:2923
sch_direct_xmit+0x31f/0x6d0 net/sched/sch_generic.c:182
__dev_xmit_skb net/core/dev.c:3092 [inline]
__dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358
dev_queue_xmit+0x17/0x20 net/core/dev.c:3423
neigh_resolve_output+0x6b9/0xb10 net/core/neighbour.c:1308
neigh_output include/net/neighbour.h:478 [inline]
ip_finish_output2+0x8b8/0x15a0 net/ipv4/ip_output.c:228
ip_do_fragment+0x1d93/0x2720 net/ipv4/ip_output.c:672
ip_fragment.constprop.54+0x145/0x200 net/ipv4/ip_output.c:545
ip_finish_output+0x82d/0xe10 net/ipv4/ip_output.c:314
NF_HOOK_COND include/linux/netfilter.h:246 [inline]
ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404
dst_output include/net/dst.h:486 [inline]
ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124
ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492
ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512
raw_sendmsg+0x26de/0x3a00 net/ipv4/raw.c:655
inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:761
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
___sys_sendmsg+0x4a3/0x9f0 net/socket.c:1985
__sys_sendmmsg+0x25c/0x750 net/socket.c:2075
SYSC_sendmmsg net/socket.c:2106 [inline]
SyS_sendmmsg+0x35/0x60 net/socket.c:2101
do_syscall_64+0x2e8/0x930 arch/x86/entry/common.c:281
return_from_SYSCALL_64+0x0/0x7a
-> #0 (_xmit_ETHER#2){+.-...}:
check_prev_add kernel/locking/lockdep.c:1830 [inline]
check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940
validate_chain kernel/locking/lockdep.c:2267 [inline]
__lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340
lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151
spin_lock include/linux/spinlock.h:299 [inline]
__netif_tx_lock include/linux/netdevice.h:3486 [inline]
sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180
__dev_xmit_skb net/core/dev.c:3092 [inline]
__dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358
dev_queue_xmit+0x17/0x20 net/core/dev.c:3423
neigh_hh_output include/net/neighbour.h:468 [inline]
neigh_output include/net/neighbour.h:476 [inline]
ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228
ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:246 [inline]
ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404
dst_output include/net/dst.h:486 [inline]
ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124
ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492
ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512
icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394
icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754
ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239
call_timer_fn+0x241/0x820 kernel/time/timer.c:1268
expire_timers kernel/time/timer.c:1307 [inline]
__run_timers+0x960/0xcf0 kernel/time/timer.c:1601
run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614
__do_softirq+0x31f/0xbe7 kernel/softirq.c:284
invoke_softirq kernel/softirq.c:364 [inline]
irq_exit+0x1cc/0x200 kernel/softirq.c:405
exiting_irq arch/x86/include/asm/apic.h:657 [inline]
smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962
apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707
__read_once_size include/linux/compiler.h:254 [inline]
atomic_read arch/x86/include/asm/atomic.h:26 [inline]
rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline]
__rcu_is_watching kernel/rcu/tree.c:1133 [inline]
rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147
rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293
radix_tree_deref_slot include/linux/radix-tree.h:238 [inline]
filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335
do_fault_around mm/memory.c:3231 [inline]
do_read_fault mm/memory.c:3265 [inline]
do_fault+0xbd5/0x2080 mm/memory.c:3370
handle_pte_fault mm/memory.c:3600 [inline]
__handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714
handle_mm_fault+0x1e2/0x480 mm/memory.c:3751
__do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397
do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460
page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&q->lock)->rlock);
lock(_xmit_ETHER#2);
lock(&(&q->lock)->rlock);
lock(_xmit_ETHER#2);
*** DEADLOCK ***
10 locks held by modprobe/12392:
#0: (&mm->mmap_sem){++++++}, at: [<ffffffff81329758>]
__do_page_fault+0x2b8/0xb60 arch/x86/mm/fault.c:1336
#1: (rcu_read_lock){......}, at: [<ffffffff8188cab6>]
filemap_map_pages+0x1e6/0x1570 mm/filemap.c:2324
#2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>]
spin_lock include/linux/spinlock.h:299 [inline]
#2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>]
pte_alloc_one_map mm/memory.c:2944 [inline]
#2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>]
alloc_set_pte+0x13b8/0x1b90 mm/memory.c:3072
#3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>]
lockdep_copy_map include/linux/lockdep.h:175 [inline]
#3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>]
call_timer_fn+0x1c2/0x820 kernel/time/timer.c:1258
#4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock
include/linux/spinlock.h:299 [inline]
#4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>]
ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201
#5: (rcu_read_lock){......}, at: [<ffffffff8389a633>]
ip_expire+0x1b3/0x6c0 net/ipv4/ip_fragment.c:216
#6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] spin_trylock
include/linux/spinlock.h:309 [inline]
#6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_xmit_lock
net/ipv4/icmp.c:219 [inline]
#6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>]
icmp_send+0x803/0x1c80 net/ipv4/icmp.c:681
#7: (rcu_read_lock_bh){......}, at: [<ffffffff838ab9a1>]
ip_finish_output2+0x2c1/0x15a0 net/ipv4/ip_output.c:198
#8: (rcu_read_lock_bh){......}, at: [<ffffffff836d1dee>]
__dev_queue_xmit+0x23e/0x1e60 net/core/dev.c:3324
#9: (dev->qdisc_running_key ?: &qdisc_running_key){+.....}, at:
[<ffffffff836d3a27>] dev_queue_xmit+0x17/0x20 net/core/dev.c:3423
stack backtrace:
CPU: 0 PID: 12392 Comm: modprobe Not tainted 4.10.0+ #29
Hardware name: Google Google Compute Engine/Google Compute Engine,
BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x2ee/0x3ef lib/dump_stack.c:52
print_circular_bug+0x307/0x3b0 kernel/locking/lockdep.c:1204
check_prev_add kernel/locking/lockdep.c:1830 [inline]
check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940
validate_chain kernel/locking/lockdep.c:2267 [inline]
__lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340
lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151
spin_lock include/linux/spinlock.h:299 [inline]
__netif_tx_lock include/linux/netdevice.h:3486 [inline]
sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180
__dev_xmit_skb net/core/dev.c:3092 [inline]
__dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358
dev_queue_xmit+0x17/0x20 net/core/dev.c:3423
neigh_hh_output include/net/neighbour.h:468 [inline]
neigh_output include/net/neighbour.h:476 [inline]
ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228
ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:246 [inline]
ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404
dst_output include/net/dst.h:486 [inline]
ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124
ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492
ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512
icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394
icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754
ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239
call_timer_fn+0x241/0x820 kernel/time/timer.c:1268
expire_timers kernel/time/timer.c:1307 [inline]
__run_timers+0x960/0xcf0 kernel/time/timer.c:1601
run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614
__do_softirq+0x31f/0xbe7 kernel/softirq.c:284
invoke_softirq kernel/softirq.c:364 [inline]
irq_exit+0x1cc/0x200 kernel/softirq.c:405
exiting_irq arch/x86/include/asm/apic.h:657 [inline]
smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962
apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707
RIP: 0010:__read_once_size include/linux/compiler.h:254 [inline]
RIP: 0010:atomic_read arch/x86/include/asm/atomic.h:26 [inline]
RIP: 0010:rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline]
RIP: 0010:__rcu_is_watching kernel/rcu/tree.c:1133 [inline]
RIP: 0010:rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147
RSP: 0000:ffff8801c391f120 EFLAGS: 00000a03 ORIG_RAX: ffffffffffffff10
RAX: dffffc0000000000 RBX: ffff8801c391f148 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 000055edd4374000 RDI: ffff8801dbe1ae0c
RBP: ffff8801c391f1a0 R08: 0000000000000002 R09: 0000000000000000
R10: dffffc0000000000 R11: 0000000000000002 R12: 1ffff10038723e25
R13: ffff8801dbe1ae00 R14: ffff8801c391f680 R15: dffffc0000000000
</IRQ>
rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293
radix_tree_deref_slot include/linux/radix-tree.h:238 [inline]
filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335
do_fault_around mm/memory.c:3231 [inline]
do_read_fault mm/memory.c:3265 [inline]
do_fault+0xbd5/0x2080 mm/memory.c:3370
handle_pte_fault mm/memory.c:3600 [inline]
__handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714
handle_mm_fault+0x1e2/0x480 mm/memory.c:3751
__do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397
do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460
page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011
RIP: 0033:0x7f83172f2786
RSP: 002b:00007fffe859ae80 EFLAGS: 00010293
RAX: 000055edd4373040 RBX: 00007f83175111c8 RCX: 000055edd4373238
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00007f8317510970
RBP: 00007fffe859afd0 R08: 0000000000000009 R09: 0000000000000000
R10: 0000000000000064 R11: 0000000000000000 R12: 000055edd4373040
R13: 0000000000000000 R14: 00007fffe859afe8 R15: 0000000000000000
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
icsk_ack.lrcvtime has a 0 value at socket creation time.
tcpi_last_data_recv can have bogus value if no payload is ever received.
This patch initializes icsk_ack.lrcvtime for active sessions
in tcp_finish_connect(), and for passive sessions in
tcp_create_openreq_child()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2ae0f17df1cd ("genetlink: use idr to track families") replaced
if (++n < fams_to_skip)
continue;
into:
if (n++ < fams_to_skip)
continue;
This subtle change cause that on retry ctrl_dumpfamily() call we omit
one family that failed to do ctrl_fill_info() on previous call, because
cb->args[0] = n number counts also family that failed to do
ctrl_fill_info().
Patch fixes the problem and avoid confusion in the future just decrease
n counter when ctrl_fill_info() fail.
User visible problem caused by this bug is failure to get access to
some genetlink family i.e. nl80211. However problem is reproducible
only if number of registered genetlink families is big enough to
cause second call of ctrl_dumpfamily().
Cc: Xose Vazquez Perez <xose.vazquez@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Fixes: 2ae0f17df1cd ("genetlink: use idr to track families")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In sk_clone_lock(), we create a new socket and inherit most of the
parent's members via sock_copy() which memcpy()'s various sections.
Now, in case the parent socket had a BPF socket filter attached,
then newsk->sk_filter points to the same instance as the original
sk->sk_filter.
sk_filter_charge() is then called on the newsk->sk_filter to take a
reference and should that fail due to hitting max optmem, we bail
out and release the newsk instance.
The issue is that commit 278571baca2a ("net: filter: simplify socket
charging") wrongly combined the dismantle path with the failure path
of xfrm_sk_clone_policy(). This means, even when charging failed, we
call sk_free_unlock_clone() on the newsk, which then still points to
the same sk_filter as the original sk.
Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually
where it tests for present sk_filter and calls sk_filter_uncharge()
on it, which potentially lets sk_omem_alloc wrap around and releases
the eBPF prog and sk_filter structure from the (still intact) parent.
Fix it by making sure that when sk_filter_charge() failed, we reset
newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(),
so that we don't mess with the parents sk_filter.
Only if xfrm_sk_clone_policy() fails, we did reach the point where
either the parent's filter was NULL and as a result newsk's as well
or where we previously had a successful sk_filter_charge(), thus for
that case, we do need sk_filter_uncharge() to release the prior taken
reference on sk_filter.
Fixes: 278571baca2a ("net: filter: simplify socket charging")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dma operation mode configuration routine was wrongly moved to a
function (stmmac_mtl_configuration) that is only executed if the
core version is >= 4.00.
Fixes: 6deee2221e11 ("net: stmmac: prepare dma op mode config for multiple queues")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds a new sysctl accept_ra_rt_info_min_plen that
defines the minimum acceptable prefix length of Route Information
Options. The new sysctl is intended to be used together with
accept_ra_rt_info_max_plen to configure a range of acceptable
prefix lengths. It is useful to prevent misconfigurations from
unintentionally blackholing too much of the IPv6 address space
(e.g., home routers announcing RIOs for fc00::/7, which is
incorrect).
Signed-off-by: Joel Scherpelz <jscherpelz@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexander reported a KMSAN splat caused by reads of uninitialized
field (tb_id_in) from user provided struct fib_result_nl
It turns out nl_fib_input() sanity tests on user input is a bit
wrong :
User can pretend nlh->nlmsg_len is big enough, but provide
at sendmsg() time a too small buffer.
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In both kmalloc and prealloc mode the bpf_map_update_elem() is using
per-cpu extra_elems to do atomic update when the map is full.
There are two issues with it. The logic can be misused, since it allows
max_entries+num_cpus elements to be present in the map. And alloc_extra_elems()
at map creation time can fail percpu alloc for large map values with a warn:
WARNING: CPU: 3 PID: 2752 at ../mm/percpu.c:892 pcpu_alloc+0x119/0xa60
illegal size (32824) or align (8) for percpu allocation
The fixes for both of these issues are different for kmalloc and prealloc modes.
For prealloc mode allocate extra num_possible_cpus elements and store
their pointers into extra_elems array instead of actual elements.
Hence we can use these hidden(spare) elements not only when the map is full
but during bpf_map_update_elem() that replaces existing element too.
That also improves performance, since pcpu_freelist_pop/push is avoided.
Unfortunately this approach cannot be used for kmalloc mode which needs
to kfree elements after rcu grace period. Therefore switch it back to normal
kmalloc even when full and old element exists like it was prior to
commit 6c9059817432 ("bpf: pre-allocate hash map elements").
Add tests to check for over max_entries and large map values.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: 6c9059817432 ("bpf: pre-allocate hash map elements")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
nfp: allow concurrency in core and minor fixes
The first 10 patches of this series prepare nfpcore for concurrent
accesses. This will be needed by upcoming hwmon and devlink patches.
Most locking is already in place, the patches in this series iron out
a few bugs.
Last 5 patches are fixes and cleanups to the netdev code, including
removal of doorbell pointers used only on old versions of the chip,
removal of unnecessarily defensive code and flushing xmit_more more
carefully on error paths.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we no longer need to keep the FW enabled for .ndo_close()
to work we can always stop FW after reconfiguration failure.
This seems to make most FWs more resilient to faults (at least
in error injection scenarios).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device open and close handlers check if the device is already
in the desired state. Thanks to our reconfig infrastructure
this should not be necessary, there doesn't seem to be any
code in the driver which depends on it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of ring full or DMA mapping error remember to flush xmit_more
delayed kicks.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP6000 doesn't use queue pointers/doorbells for RX, it uses
'done' bit in descriptors. Remove the pointers from data structures.
Since we are saving space in rx_ring structure make fields we
previously compressed to 16bits word size again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix warning which was using netdev_warn() instead of dev_warn()
to early.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
