| Age | Commit message (Collapse) | Author |
|---|
|
This adds support for using CS42L42 as a SoundWire device.
SoundWire-specifics are kept separate from the I2S implementation as
much as possible, aiming to limit the risk of breaking the I2C+I2S
support.
There are some important differences in the silicon behaviour between
I2S and SoundWire mode that are reflected in the implementation:
- ASP (I2S) most not be used in SoundWire mode because the two interfaces
share pins.
- The SoundWire capture (record) port only supports 1 channel. It does
not have left-to-right duplication like the ASP.
- DP2 can only be prepared if the HP has powered-up. DP1 can only be
prepared if the ADC has powered-up. (This ordering restriction does
not exist for ASPs.) The SoundWire core port-prepare step is
triggered by the DAI-link prepare(). This happens before the
codec DAI prepare() or the DAPM sequence so these cannot be used
to enable HP/ADC. Instead the HP/ADC enable/disable are done during
the port_prep callback.
- The SRCs are an integral part of the audio chain but in silicon their
power control is linked to the ASP. There is no equivalent power link
to SoundWire DPs so the driver must take "manual" control of SRC power.
- The SoundWire control registers occupy the lower part of the SoundWire
address space so cs42l42 registers are offset by 0x8000 (non-paged) in
SoundWire mode.
- Register addresses are 8-bit paged in I2C mode but 16-bit unpaged in
SoundWire.
- Special procedures are needed on register read/writes to (a) ensure
that the previous internal bus transaction has completed, and
(b) handle delayed read results, when the read value could not be
returned within the SoundWire read command.
There are also some differences in driver implementation between I2S
and SoundWire operation:
- CS42L42 I2S does not runtime_suspend, but runtime_suspend/resume support
has been added into the driver in SoundWire mode as the most convenient
way to power-up the bus manager and to handle the unattach_request
condition, though the CS42L42 chip does not itself suspend or resume.
- Intel SoundWire host controllers have a low-power clock-stop mode that
requires resetting all peripherals when resuming. This means that the
interrupt registers will be reset in between the interrupt being
generated and the interrupt being handled, and since the interrupt
status is debounced, these values may not be accurate immediately,
and may cause spurious unplug events before settling.
- As in I2S mode, the PLL is only used while audio is active because
of clocking quirks in the silicon. For SoundWire the cs42l42_pll_config()
is deferred until the DAI prepare(), to allow the cs42l42_bus_config()
callback to set the SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-7-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Export functions that will be needed by a SoundWire module.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-6-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Setup of the ASP (audio serial port) was being done as a side-effect of
cs42l42_pll_config() and forces a restriction on the ratio of sample_rate
to bit_clock that is invalid for Soundwire.
Move the ASP setup into a dedicated function.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-5-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The chosen clocking configuration must give an internal MCLK (MCLKint)
that is an integer multiple of the sample rate.
On I2S each of the supported bit clock frequencies can only be generated
from one sample rate group (either the 44100 or the 48000) so the code
could use only the bitclock to look up a PLL config.
The relationship between sample rate and bitclock frequency is more
complex on Soundwire and so it is possible to set a frame shape to
generate a bitclock from the "wrong" group. For example 2*147 with a
48000 sample rate would give a bitclock of 14112000 which on I2S
could only be derived from a 44100 sample rate.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SOFT_RESET_REBOOT register is needed to recover CS42L42 state after
a Soundwire bus reset.
This is required to be set whenever there is severe/hard bus reset.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, port_prep callback only has commands for PRE_PREP, PREP,
and POST_PREP, which doesn't directly say whether this is for a
prepare or deprepare call. Extend the command list enum to say
whether the call is for prepare or deprepare aswell.
Also remove SDW_OPS_PORT_PREP from sdw_port_prep_ops as this is unused,
and update this enum to be simpler and more consistent with enum
sdw_clk_stop_type.
Note: Currently, the only users of SDW_OPS_PORT_POST_PREP are codec
drivers sound/soc/codecs/wsa881x.c and sound/soc/codecs/wsa883x.c, both
of which seem to assume that POST_PREP only occurs after a prepare,
even though it would also have occurred after a deprepare. Since it
doesn't make sense to mark the port prepared after a deprepare, changing
the enum to separate PORT_DEPREP from PORT_PREP should make the check
for PORT_PREP in those drivers be more logical.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230127165111.3010960-2-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the bindings checks like syntax error.
Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230131050946.14385-1-kiseok.jo@irondevice.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230131082107.174739-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add Kiseok Jo as maintainer for Iron Device audio codec drivers.
Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Link: https://lore.kernel.org/r/20230131054526.14653-1-kiseok.jo@irondevice.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current snd_soc_dai has data for Playback/Capture, but it is very
random. Someone is array (A), someone is playback/capture (B),
and someone is tx/rx (C);
struct snd_soc_dai {
...
(A) unsigned int stream_active[SNDRV_PCM_STREAM_LAST + 1];
(B) struct snd_soc_dapm_widget *playback_widget;
(B) struct snd_soc_dapm_widget *capture_widget;
(B) void *playback_dma_data;
(B) void *capture_dma_data;
...
(C) unsigned int tx_mask;
(C) unsigned int rx_mask;
};
Because of it, the code was very complicated.
This patch creates new data structure to merge these into one,
and tidyup the code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87cz6vea1v.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87edrbea20.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87fsbrea25.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Link: https://lore.kernel.org/all/6f047ec5-4055-761d-c1ea-c2d0b606e53a@linux.intel.com/
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h6w7ea2a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87ilgnea2p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87k013ea2u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87leljea35.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mt5zea3a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7qfea3f.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmavea3l.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/87r0vbea3r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/87sffrea3z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tu07ea45.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8knea4b.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87wn53ea4i.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y1pjea4n.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zg9zea4w.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871qnbfopt.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87357rfoq1.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874js7foqb.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC framework/driver checks whether card was instantiated every
where. Then, it should check card pointer too in such case.
This patch adds snd_soc_card_is_instantiated() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/875ycnfoqp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_soc_dai_get_widget() requests SNDRV_PCM_STREAM_PLAYBACK/CAPTURE.
This patch adds helper for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/877cx3foqz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has tx/rx_mask, and is directly accessing to them,
but accessing to it via function is nice idea.
This patch adds snd_soc_dai_tdm_mask_set/get() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/878rhjfor8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has snd_soc_dai_set/get_dma_data() which is assuming
struct snd_pcm_substream to get Playback/Capture direction.
But, many drivers want to use it not through snd_pcm_substream.
This patch adds more low level snd_soc_dai_dma_data_set/get() for it,
and previous functions will be macro for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87a61zfori.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has snd_soc_dai_get_widget() (= _get_) but doesn't
have _set_ function. This patch adds it.
This patch also cleanup unnecessary line break for _get_ function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87bkmfforp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
Following is series of fixes and cleanups for core topology code. Few
patches fixing various problems all around and few fixing function
names.
|
|
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
Audio-Graph-Card and Simple-Audio-Card are similar Card
and are sharing same utils. Thus we can also sharing same schema.
This patch-set fixup some Renesas's "make dtbs_check".
|
|
Add a DT schema for describing Awinic AW88395 audio amplifiers. They are
controlled using I2C.
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230113055301.189541-6-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-5-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Ben Yi <yijiangtao@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-4-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-3-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
associated operation functions
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-2-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After contributing the driver, add myself as the maintainer for the
Renesas IDT821034 codec.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230126085137.375814-4-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Renesas IDT821034 codec is four channel PCM codec with on-chip
filters and programmable gain setting.
It also provides SLIC (Subscriber Line Interface Circuit) signals as
GPIOs.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230126085137.375814-3-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Renesas IDT821034 codec is a quad PCM codec with programmable
gain.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230126085137.375814-2-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document data structures used by mchp-spdifrx driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-9-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add runtime PM support for Microchip SPDIFRX driver. On runtime suspend
the clocks are disabled and regmap is set in caching mode. On runtime
resume the clocks are enabled and regmap is synced with the device.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-8-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove member fmt of struct mchp_spdifrx_dev as it is not used anywhere.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-7-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
clk_get_rate() returns an unsigned long. Use a variable of type
unsigned long to store it.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-6-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
CSC interrupts which might be used in controls are on bits 8 and 9 of
SPDIFRX_IDR register. Thus disable all the interrupts that are exported
by driver.
Fixes: ef265c55c1ac ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-5-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Channel status get and channel subcode get controls relies on data
returned by controls when certain IRQs are raised. To achieve that
completions are used b/w controls and interrupt service routine. The
concurrent accesses to these controls are protected by
struct snd_card::controls_rwsem.
Issues identified:
- reinit_completion() may be called while waiting for completion
which should be avoided
- in case of multiple threads waiting, the complete() call in interrupt
will signal only one waiting thread per interrupt which may lead to
timeout for the others
- in case of channel status get as the CSC interrupt is not refcounted
ISR may disable interrupt for threads that were just enabled it.
To solve these the access to controls were protected by a mutex. Along
with this there is no need for spinlock to protect the software cache
reads/updates b/w controls and ISR as the update is happening only when
requested from control, and only one reader can reach the control.
Fixes: ef265c55c1ac ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
