| Age | Commit message (Collapse) | Author |
|---|
|
Now that the mutexes for output and capture vb2 queues match,
it is possible to refer to the context q_lock as the
m2m lock for a given m2m context.
Remove the output/capture lock selection.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Currently, all the mem2mem driver either use a single mutex
to lock the capture and output videobuf2 queues, or don't
set any mutex.
This means the mutexes match, and so the mem2mem framework
is able to set the m2m context lock.
Enforce this by making it mandatory for drivers to set
the same capture and output mutex, or not set any mutex at all.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add devicetree binding documentation for firmware loader for video
hardware running on qualcomm chip.
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Video hardware is mainly comprised of vcodec subsystem and video
control subsystem. Video control has ARM9 which executes the video
firmware instructions whereas vcodec does the video frame processing.
This change adds support to load the video firmware and bring ARM9
out of reset for platforms which does not have trustzone.
An iommu domain is associated and managed with the firmware device.
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This registers a firmware platform_device and associate it with
video-firmware DT subnode. Then calls dma configure to initialize
dma and iommu.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Separate firmware loading part into a new function.
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add routine to reset the ARM9 and brings it out of reset. Also
abstract the Venus CPU state handling with a new function. This
is in preparation to add PIL functionality in venus driver.
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When vivid_update_format_cap() is called it should free any overlay
bitmap since the compose size will change.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+0cc8e3cc63ca373722c6@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
text[s] is a signed char, so using that as index into the font8x16 array
can result in negative indices. Cast it to u8 to be safe.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+ccf0a61ed12f2a7313ee@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v4.7 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Update file paths in MAINTAINERS.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Joe Perches <joe@perches.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
vb2_core_create_bufs did not check if the memory model for newly added
buffers is the same as for already existing buffers. It should return an
error if they aren't the same.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+e1fb118a2ebb88031d21@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v4.16 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.
However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.
Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The use of flush_schedule_work() made no sense and caused a syzkaller error.
Replace with the correct cancel_delayed_work_sync().
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+69780d144754b8071f4b@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v4.20 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If you create multiple vivid instances, each with their own media
device, then there was no way to tell them apart.
Fill in the bus_info so each instance has a unique bus_info string.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The video_device structure is only copied into another structure, so
it can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The capture DV timings capabilities allowed for a minimum width and
height of 0. So passing a timings struct with 0 values is allowed
and will later cause a division by zero.
Ensure that the width and height must be >= 16 to avoid this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+57c3d83d71187054d56f@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
kthread_run returns an error pointer, but elsewhere in the code
dev->kthread_vid_cap/out is checked against NULL.
If kthread_run returns an error, then set the pointer to NULL.
I chose this method over changing all kthread_vid_cap/out tests
elsewhere since this is more robust.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+53d5b2df0d9744411e2e@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The fields of a v4l2_subdev_ops structure are all const, so the
structures that are stored there and are not used elsewhere can be
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The v4l2_m2m_ops structure can be const as it is only passed to
v4l2_m2m_init whose parameter is const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The v4l2_ctrl_ops structure is only stored in the ops field of a
v4l2_ctrl_config structure, and this field is const, or passed as the
second argument of v4l2_ctrl_new_std, and the corresponding parameter
is declared as const. Accordingly, the structure can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Do a series of minor corrections at the V4L2 uAPI documentation.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
I noticed that repeatedly running 'cec-ctl --playback' would occasionally
select 'Playback Device 2' instead of 'Playback Device 1', even though there
were no other Playback devices in the HDMI topology. This happened both with
'real' hardware and with the vivid CEC emulation, suggesting that this was an
issue in the core code that claims a logical address.
What 'cec-ctl --playback' does is to first clear all existing logical addresses,
and immediately after that configure the new desired device type.
The core code will poll the logical addresses trying to find a free address.
When found it will issue a few standard messages as per the CEC spec and return.
Those messages are queued up and will be transmitted asynchronously.
What happens is that if you run two 'cec-ctl --playback' commands in quick
succession, there is still a message of the first cec-ctl command being transmitted
when you reconfigure the adapter again in the second cec-ctl command.
When the logical addresses are cleared, then all information about outstanding
transmits inside the CEC core is also cleared, and the core is no longer aware
that there is still a transmit in flight.
When the hardware finishes the transmit it calls transmit_done and the CEC core
thinks it is actually in response of a POLL messages that is trying to find a
free logical address. The result of all this is that the core thinks that the
logical address for Playback Device 1 is in use, when it is really an earlier
transmit that ended.
The main transmit thread looks at adap->transmitting to check if a transmit
is in progress, but that is set to NULL when the adapter is unconfigured.
adap->transmitting represents the view of userspace, not that of the hardware.
So when unconfiguring the adapter the message is marked aborted from the point
of view of userspace, but seen from the PoV of the hardware it is still ongoing.
So introduce a new bool transmit_in_progress that represents the hardware state
and use that instead of adap->transmitting. Now the CEC core waits until the
hardware finishes the transmit before starting a new transmit.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If debug_phys_addr is set, then CEC_CAP_PHYS_ADDR is added to the CEC
adapter capabilities.
This allows for testing CEC even if the physical address isn't set. This
makes it possible to connect two HDMI outputs together and still use CEC.
Very useful for testing CEC if you don't have access to an HDMI receiver
under linux.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The CEC specification requires that the Vendor ID (if any) is reported
after a logical address was claimed.
This was never done, so add support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The CEC IP is very similar between the three HDMI receivers, but
not identical. Add support for all three variants.
Tested with an adv7604 and an adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If a filehandle is dup()ped, then it is possible to close it from one fd
and call mmap from the other. This creates a race condition in vb2_mmap
where it is using queue data that __vb2_queue_free (called from close())
is in the process of releasing.
By moving up the mutex_lock(mmap_lock) in vb2_mmap this race is avoided
since __vb2_queue_free is called with the same mutex locked. So vb2_mmap
now reads consistent buffer data.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: syzbot+be93025dd45dccd8923c@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Return 0 when invalidating the logical address. The cec core produces
a warning for drivers that do this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Torbjorn Jansson <torbjorn.jansson@mbox200.swipnet.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If the tx_ignore_nack_until_eom error injection was activated,
then tx_nacked was never set instead of setting it when the last
byte of the message was transmitted.
As a result the transmit was marked as OK, when it should have
been NACKed.
Modify the condition so that it always sets tx_nacked when the
last byte of the message was transmitted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Documentation and code was linking the old documentation at:
http://v4l2spec.bytesex.org/spec/x1904.htm
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
drivers/staging/media/sunxi/cedrus/cedrus.c:421:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 50e761516f2b ("media: platform: Add Cedrus VPU decoder driver")
CC: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The R-Car CSI-2 interface has a number of selectable 'channels' that
provides pixel data to the VINs during image acquisition.
Each channel can be used to match a CSI-2 data type and a CSI-2 virtual
channel to be routed to output path.
Different SoCs have different number of channels, with R-Car E3 being the
notable exception supporting only 2 of them.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Update PHTW tables for V3M and E3 SoCs to the latest datasheet release
(R-Car Series, 3rd Generation manual rev1.00 20181017).
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add support for R-Car E3 R8A77965 to R-Car CSI-2 driver.
Based on the experimental patch from Magnus Damm.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add compatible string for R-Car E3 R8A77990 to the list of supported SoCs.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add R-Car E3 R8A77990 SoC to the rcar-vin supported ones.
Based on the experimental patch from Magnus Damm.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add compatible string for R-Car E3 R8A77990 to the list of SoCs supported by
rcar-vin driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Improve the pxp_soft_reset() error message by moving it to the
caller function, associating it with a proper device and also
by displaying the error code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
pxp_soft_reset() may fail with a timeout, so it is better to propagate
the error in this case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In addition to the S_FMT debug output, S_SELECTION (SEL_TGT_CROP) is
relevant to determine encoded size. Add debug output for it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Consistently add the context index to debug output, which otherwise is
impossible to make sense of when two contexts are running concurrently.
For this purpose, add a convenience macro coda_dbg(). Use the function
name with the coda_ prefix stripped as keyword where applicable, and
consistently use vid-out and vid-cap names for the queues. Add sequence
counters to the decoder job finished message and correctly indicate B
frames. Add a start streaming message to complement the stop streaming
message and a start encoding message to complement the existing start
decoding message.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Use v4l2_type_names to indicate which of the two queues is busy.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The error code looks much more like a bit field than an error value.
Print it as hex rather than decimal.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
v4l2-compliance complains if S_SELECTION returns 0 for read-only targets.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
v4l2-compliance complains if G_PARM returns 0 in the denominator.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
v4l2-compliance complains about S_PARM being supported, but not
ENUM_FRAMEINTERVALS.
Report a continuous frame interval even though the hardware only
supports 16-bit numerator and denominator, with min/max values
that can be programmed into the mailbox registers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The flag is already set in coda_g_parm, but v4l2-compliance complains
about it not being set during S_PARM.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The CODA driver uses threaded IRQs only, so there is nothing happening
in hardirq context that could interfere with the buffer meta handling.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The per-device instance list is unused, remove it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Three macroblocks seem to be the minimum resolution that can be encoded
and decoded by the CODA960 h.264 codec. Picture run commands fail for
smaller resolutions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
