summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-10-11iwlwifi: pcie: restart the driver when a command times outEmmanuel Grumbach
This should really not happen. If it does, restarting is the only way to recover since the driver and the firmware might very well be out of sync. Moreover, iwl_op_mode_nic_error will print data that might help debugging. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-11iwlwifi: mvm: BT Coex - set the proper LUT for single ant devicesEmmanuel Grumbach
Single shared antenna devices need a special LUT. Address this need. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-11iwlwifi: mvm: BT Coex - don't limit agg size in loose schemeEmmanuel Grumbach
In loose BT Coex scheme, the aggregation size doesn't need to be limited. To avoid triggering it, remove a lockdep assertion - we need to compute the AMPDU size limit from rate control code which can't take mvm->mutex. This means that there is a race but in the worst case, we will have a wrong AMPDU size limit which is not a big issue. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-11Bluetooth: Provide hdev parameter to hci_recv_frame() driver callbackMarcel Holtmann
To avoid casting skb->dev into hdev, just let the drivers provide the hdev directly when calling hci_recv_frame() function. This patch also fixes up all drivers to provide the hdev. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11Bluetooth: Remove unused h4_check_data_len() functionMarcel Holtmann
The function h4_check_data_len() is actually not used. So just remove it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11Bluetooth: Remove return value from hci_send_frame() functionMarcel Holtmann
The return value of hci_send_frame() is never checked. So just make this function void and print an error when the hdev->send driver callback returns a negative value. Having the error printed is actually an improvement over the current situation where any driver error just gets ignored. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11Bluetooth: Remove pointless check of hci_send_frame parameterMarcel Holtmann
The hdev parameter of hci_send_frame must be always valid. If the hdev is not valid, it would not even make it to this stage. The callers will have already accessed hdev at that point many times. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11Bluetooth: Move skb->dev assignment for hdev->send into central placeMarcel Holtmann
The assignement of skb->dev is done all over the place. So it makes it hard to eventually get rid of it. Move it all in one central place so it gets assigned right before calling hdev->send driver callback. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11Bluetooth: Move smp.h header file into net/bluetooth/Marcel Holtmann
The smp.h header file is only used internally by the bluetooth.ko module and is not a public API. So make it local to the core Bluetooth module. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11Bluetooth: Move a2mp.h header file into net/bluetooth/Marcel Holtmann
The a2mp.h header file is only used internally by the bluetooth.ko module and is not a public API. So make it local to the core Bluetooth module. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11Bluetooth: Move amp.h header file into net/bluetooth/Marcel Holtmann
The amp.h header file is only used internally by the bluetooth.ko module and is not a public API. So make it local to the core Bluetooth module. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Remove hdev->ioctl driver callbackMarcel Holtmann
Since there is no use of hdev->ioctl by any Bluetooth driver since ever, so just lets remove it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Remove unused btmrvl_ioctl() callbackMarcel Holtmann
The btmrvl_ioctl() function is not used and thus remove it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Remove unused dtl1_hci_ioctl() callbackMarcel Holtmann
The dtl1_hci_ioctl() function is not used and thus remove it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Remove unused btuart_hci_ioctl() callbackMarcel Holtmann
The btuart_hci_ioctl() function is not used and thus remove it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Remove unused bt3c_hci_ioctl() callbackMarcel Holtmann
The bt3c_hci_ioctl() function is not used and thus remove it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Remove unused bluecard_hci_ioctl() callbackMarcel Holtmann
The bluecard_hci_ioctl() function is not used and thus remove it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Remove unused bfusb_ioctl() callbackMarcel Holtmann
The bfusb_ioctl() function is not used and thus remove it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: AMP contollers do not support the legacy ioctlsMarcel Holtmann
The legacy ioctls for device specific commands including inquiry are not support by AMP controllers. So just reject them right away instead of trying to send the HCI command and wait for failure from the actual hardware. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Use hci_conn_num() instead of direct connection hash accessMarcel Holtmann
When changing the alternate setting for the ISOC endpoints, use the hci_conn_num() helper function to count currently established SCO and eSCO connections and store the the value. This avoids direct access to the connection hash. In addition use the stored value instead accessing the connection hash over and over again. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Use hci_conn_num() for checking number of LE connectionsMarcel Holtmann
When checking for the current number of LE connections, use hci_conn_num() function instead of a full blown lookup within the connection hash or direct access of the counters. In the case of re-enabling advertising, it is more useful to check for any connection attempt or existing connection. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Fix too long line with set_advertising() functionMarcel Holtmann
The function declaration goes over 80 characters, so break it down. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10rt2x00: rt2800lib: fix VGC adjustment for RT3572 and RT3593Gabor Juhos
The Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022 reference driver uses different RSSI threshold and VGC adjustment values for the RT3572 and RT3593 chipsets. Update the rt2800_link_tuner function to use the same values. Also change the comment in the function to make it more generic. References: RT35xx_ChipAGCAdjust function in chips/rt35xx.c RSSI_FOR_MID_LOW_SENSIBILITY constant in include/chip/rtmp_phy.h RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: rt2800lib: fix VGC adjustment for RT5592Gabor Juhos
In commit 3d81535ea5940446510a8a5cee1c6ad23c90c753 (rt2800: 5592: add chip specific vgc calculations) the rt2800_link_tuner function has been modified to adjust VGC level for the RT5592 chipset. On the RT5592 chipset, the VGC level must be adjusted only if rssi is greater than -65. However the current code adjusts the VGC value by 0x10 regardless of the actual chipset if the rssi value is between -80 and -65. Fix the broken behaviour by reordering the if-else statements. Cc: stable@vger.kernel.org Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: use generic EWMA functions for average RSSI calculationsGabor Juhos
Remove the local MOVING_AVERAGE implementation, and use the generic EWMA functions instead. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: rt2800lib: no need to toggle RF R30 bit 7 twiceKevin Lo
In rt2800_config_channel_rf3xxx(), there's no need to toggle RF R30 bit 7 twice. Signed-off-by: Kevin Lo <kevlo@kevlo.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10net: p54spi: remove deprecated IRQF_DISABLEDMichael Opdenacker
This patch proposes to remove the use of the IRQF_DISABLED flag It's a NOOP since 2.6.35 and it will be removed one day. Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: do not pause queue on flushStanislaw Gruszka
Pausing queue on flush make no sense since txdone procedure un-pause queue. Before flush procedure we have to assure queue is stopped, i.e. on receive path h/w RX is disabled, on transmit path queue is disabled in mac80211. That conditions are true except one function: rt2x00usb_watchdog_tx_dma(), so add stop/start queue there. Note stop/start queue can be racy if we do this from multiple paths, but currently we stop TX queues only on rt2x00lib_disable_radio(), which also stop/sync watchdog, hance we have no race condition. Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: rt2800lib: fix default VGC values for RT3572 for the 5GHz bandGabor Juhos
The rt2x00 driver uses 0x22 as a default VGC value in VGC adjustment for the RT3572 chipset. In the Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022 driver, this value is only used for initialization. During VGC adjustment, the reference driver uses different values. Update the 'rt2800_get_default_vgc' function to synchronize the values with the reference driver. Also add the missing AGC initialization code into the 'rt2800_config_channel' function. References: RT35xx_SetAGCInitValue in chip/rt35xx.c RT35xx_ChipAGCAdjust in chip/rt35xx.c Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: rt2800lib: fix VGC programming for RT3572 and RT3593Gabor Juhos
According to the DPO_RT5572_LinuxSTA_2.6.1.3_20121022 reference driver, programming of the 'BBP 66' register on the RT3572 and RT3593 chipsets must be done via the 'rt2800_bbp_write_with_rx_chain' function. This ensures that value is correclty set for all RX chains. References: RT35xx_ChipAGCAdjust and RT35xx_SetAGCInitValue functions in chips/rt35xx.c Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: rt2800lib: fix default VGC values for RT3593Gabor Juhos
Update the rt2800_get_default_vgc function to use the same VGC values that the DPO_RT5572_LinuxSTA_2.6.1.3_20121022 reference driver uses. References: RT35xx_ChipAGCAdjust in chips/rt35xx.c RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: rt2800lib: remove TXPOWER_DELTA entry from extended EEPROM mapGabor Juhos
The TXPOWER_DELTA field of the regular EEPROM stores the TX power compensation value for HT40. The extended EEPROM has no such field, it stores separate TX power values for HT20 and for HT40. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Paul Menzel <paulepanter@users.sourceforge.net> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00: rt2800lib: remove TXMIXER_GAIN entries from the extended EEPROM mapGabor Juhos
The comments are indicating that the TXMIXER_GAIN_BG and TXMIXED_GAIN_A entries are overlapping with the RSSI_BG2 and RSSI_A2 entries in the extended EEPROM map. This is not correct, because the upper byte of the RSSI_BG2 and RSSI_A2 entries are reserved. There are no TX mixer gain values are stored at all in the extended EEPROM. Remove the initialization of these entries from the extended EEPROM map to reflect this. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Paul Menzel <paulepanter@users.sourceforge.net> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10brcmsmac: add support for a BCM4313 with PCI id 0x4313Hauke Mehrtens
There are some BCM4313 out there with a PCI id of 0x4313. These devices are missing a sprom and are only used on routers or other embedded devices. We found one connected to a BCM63XX SoC. This devices was found by someone in this ticket: https://dev.openwrt.org/ticket/13551 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10bcma: add PCI id 0x4313Hauke Mehrtens
This PCI id is used by some BCM4313 cards without a sprom. I have seen such a card on a router connected to some BCM63XX SoC via PCIe. There are cards out there with the same PCI id and a BCM4311, which is a pre ieee80211n chip only supporting ieee80211a, these are still not supported by b43 and not detected by ssb. This devices was found by someone in this ticket: https://dev.openwrt.org/ticket/13551 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10bcma: reject PCI cards in bcma.Hauke Mehrtens
bcma currently only supports PCIe cards and no PCI cards, reject them if we find them. I have never heard of any PCI card using the AI bus (bcma), all of them are using ssb instead. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10net: wireless: wl1251: update firmware pathFelipe Balbi
TI firmwares are located under ti-connectivity directory. Update path to make sure driver can find and load firmware blob. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10rt2x00_pci: Fix interrupt handler name (visible at /proc/interrupts)Kirill Tkhai
Currently driver name is wrong. PCI device address is visible at /proc/interrupts instead of the name: 43: 124 0 0 0 PCI-MSI-edge rtsx_pci 44: 384 0 0 0 PCI-MSI-edge snd_hda_intel 45: 25096 0 0 0 PCI-MSI-edge 0000:01:00.0 ^^^^^^^^^^^^ So, pass the right name. rt2x00_ops->name contains KBUILD_MODNAME and good for that, so pass it. Handler names will be "rt2500pci", "rt2500pci" etc. Signed-off-by: Kirill Tkhai <tkhai@yandex.ru> CC: Ivo van Doorn <IvDoorn@gmail.com> CC: Gertjan van Wingerde <gwingerde@gmail.com> CC: Helmut Schaa <helmut.schaa@googlemail.com> CC: linux-wireless@vger.kernel.org Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardwareEugene Krasnikov
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So far WCN3660/WCN3680 is available only on MSM platform. Firmware can be found here: https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS Wiki page is available here: http://wireless.kernel.org/en/users/Drivers/wcn36xx A lot people made a contribution to this driver. Here is the list in alphabetical order: Eugene Krasnikov <k.eugene.e@gmail.com> Kalle Valo <kvalo@qca.qualcomm.com> Olof Johansson <dev@skyshaper.net> Pontus Fuchs <pontus.fuchs@gmail.com> Yanbo Li <yanbol@qti.qualcomm.com> Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10mwifiex: Change variable type to boolPeter Senna Tschudin
The variables cancel_scan_cmd, enable_data, hs_activate and valid are only assigned the values true and false. Change its type to bool. The simplified semantic patch that find this problem is as follows (http://coccinelle.lip6.fr/): @exists@ type T; identifier b; @@ - T + bool b = ...; ... when any b = \(true\|false\) Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-10Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-10-10Bluetooth: Fix checking for HCI_SETUP flag when receiving mgmt commandsJohan Hedberg
When the HCI_SETUP flag is set the controller has not yet been announced over mgmt and therefore doesn't exist from that perspective. If we nevertheless get a mgmt command for it we should respond with the appropriate INVALID_INDEX error. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-10Bluetooth: Fix potential double-frees of L2CAP skbsJohan Hedberg
The l2cap_recv_frame function is expected to take ownership and eventually free the skb passed to it. We need to ensure that the conn->rx_skb pointer is no longer reachable when calling l2cap_recv_frame so that no other function, such as l2cap_conn_del, may think that it can free conn->rx_skb. An actual situation when this can happen is when smp_sig_channel (called from l2cap_recv_frame) fails and l2cap_conn_del gets called as a consequence. The l2cap_conn_del function would then try to free conn->rx_skb, but as the same skb was just passed to smp_sig_channel and freed we get a double-free. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-10Bluetooth: Restrict high speed support to SSP enabled controllersMarcel Holtmann
The support for Bluetooth High Speed can only be enabled on controllers where also Secure Simple Pairing has been enabled. Trying to enable high speed when SSP is disabled will result into an error. Disabling SSP will at the same time disable high speed as well. It is required to enforce this dependency on SSP since high speed support is only defined for authenticated, unauthenticated and debug link keys. These link key types require SSP. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Remove unneeded val variable when setting SSPMarcel Holtmann
The variable val in the set_ssp() function of the management interface is not needed. Just use cp->val directly since its input values have already been validated. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10Bluetooth: Refactor hci_connect_leAndre Guedes
This patch does some code refactoring in hci_connect_le() by moving the exception code into if statements and letting the main flow in first level of function scope. It also adds extra comments to improve the code readability. Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-10Bluetooth: Use HCI request for LE connectionAndre Guedes
This patch introduces a new helper, which uses the HCI request framework, for creating LE connectons. All the handling is now done by this function so we can remove the hci_cs_le_create_conn() event handler. This patch also removes the old hci_le_create_connection() since it is not used anymore. Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-09ath10k: remove unneded semicolon from ath10k_core_fetch_firmware_api_n()Fengguang Wu
drivers/net/wireless/ath/ath10k/core.c:507:2-3: Unneeded semicolon Removes unneeded semicolon. Generated by: coccinelle/misc/semicolon.cocci Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-09ath10k: fix ath10k_debug_start() lockingKalle Valo
ath10k_debug_start() was not called with conf_mutex, fix that. Also there was a deadlock in ath10k_debug_stop(), rename it to ath10k_debug_destroy() and call it only when the device is destroyed. Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-08ath10k: Fix bug in max. VHT A-MPDU sizeSujith Manoharan
For VHT peers, the maximum A-MPDU size has to be calculated from the VHT capabilities element and not the HT-cap. The formula is the same, but a higher value is used in VHT, allowing larger aggregates to be transmitted. The patch contains a workaround for some Netgear/Linksys APs that report Rx A-MPDU factor incorrectly. Tested-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
generated by cgit (git 2.34.1) at 2025-07-16 19:19:05 +0000