| Age | Commit message (Collapse) | Author |
|---|
|
Martin Blumenstingl says:
====================
dwmac-meson8b: clock fixes for Meson8b
this series is now successfully tested, thus we think it's ready to be
applied to your net-next tree.
Emiliano reported [0] that he couldn't get dwmac-meson8b to work on his
Odroid-C1. This is the (hopefully) final version of this series, which
was successfully tested.
Due to the fact that the public S805/S905/S912 datasheets all seem to
be outdated regarding the description of the PRG_ETH0 (also called
PRG_ETHERNET_ADDR0) register Linus Lüssing offered to help testing with
an oscilloscope and an Odroid-C1. I would like to say HUGE thanks to him
at this point as he spent hours figuring out the effects of the bits
that are (though to be) relevant to get Ethernet working on the
Odroid-C1.
We tested three scenarios, all based on version 3 of this series:
1) MPLL2 at ~500MHz, m250_div set to 1, bit 10 enabled
this resulted in a clock rate twice as high as expected at the RGMII TX
clock pin (250MHz instead of 125MHz for Gbit connections and 50MHz
instead of 25MHz for 100Mbit/s connections). it did not change the
rate at the XTAL_IN pin of PHY (which stayed consistenly at 25MHz)
2) MPLL2 at ~250MHz, m250_div set to 1, bit 10 disabled
the oscilloscope shows "no clock" for the RGMII TX clock pin at it's
highest resolution (and random rates at lower resolutions). XTAL_IN is
still at 25MHz
3) MPLL2 at ~250MHz, m250_div set to 1, bit 10 enabled
this resulted in a 125MHz signal at the RGMII TX clock pin for Gbit
speeds and 25MHz for 100Mbit/s - both values are as expected. The rate
on the XTAL_IN pin was at 25MHz
-> boot-logs (with the PRG_ETH0 register value) and screenshots from the
readings of the oscilloscope can be found at:
https://metameute.de/~tux/linux/amlogic/odroidc1/ethernet/
Version 4 of this series is based on the results from Linus Lüssing's
help with the oscilloscope and Odroid-C1.
Unfortunately I don't have any Meson8b boards with RGMII PHY so I could
only partially test this. @Emiliano: Could you please give this version
a try and let me know about the results (preferably with a "Tested-by"
if it works)?
You obviously still need your two "ARM: dts: meson8b" patches which
- add the amlogic,meson8b-dwmac" compatible to meson8b.dtsi
- enable Ethernet on the Odroid-C1 (according to your last thest a TX
delay of 4ns is required to make it work properly)
When testing on Meson8b this also needs a fix for the MPLL clock driver:
"clk: meson: mpll: use 64-bit maths in params_from_rate", see:
https://patchwork.kernel.org/patch/10131677/
I have tested this myself on a Khadas VIM (GXL SoC, internal RMII PHY)
and a Khadas VIM2 (GXM SoC, external RGMII PHY). Both are still working
fine (so let's hope that this also fixes your Meson8b issue :)).
changes since v4 at [4]:
- dropped "RFT" status since Jerome tested this series successfully!
- dropped PATCH #2 ("simplify generating the clock names"). I will
improve the whole clock registration in a separate series. since that
patch didn't really improve anything I dropped it for now
- added Jerome's Acked-/Reviewed-/Tested-by's - many thanks!
changes since v3 at [3]:
- renamed the function PATCH #1 from meson8b_init_rgmii_clk to
meson8b_init_rgmii_tx_clk since we now know what the register bits
mean
- rewrote PATCH #3 because bit 10 is a gate clock and it seems that
there is an internal fixed divide-by-2 clock. see the patch
description for a detailed explanation
- updated the description of PATCH #4 and #5 as the clock we're trying
to fix is the "RGMII TX" clock (old version stated that this is the
"RGMII clock" or "PHY reference clock"). also updated the numbers in
the description now that we have the clock hierarchy right (at least
we hope so)
changes since v2 at [2]:
- added PATCH #2 to make the following patch easier
- Emiliano reported that there's currently another bug in the
dwmac-meson8b driver which prevents it from working with RGMII PHYs on
Meson8b: bit 10 of the PRG_ETH0 register is configures a clock gate
(instead of a divide by 5 or divide by 10 clock divider). This has not
been visible on GXBB and later due to the input clock which always led
to a selection of "divide by 10" (which is done internally in the IP
block, but the bit actually means "enable RGMII clock output").
PATCH #3 was added to address this issue.
- the commit message of PATCH #4 and #5 (formerly PATCH #2 and #3) were
updated and the patch itself rebased because the m25_div clock was
removed with the new PATCH #3 (so some of the statements were not
valid anymore)
changes since v1 at [1]:
- changed the subject of the cover-letter to indicate that this is all
about the RGMII clock
- added PATCH #1 which ensures that we don't unnecessarily change the
parent clocks in RMII mode (and also makes the code easier to
understand)
- changed subject of PATCH #2 (formerly PATCH #1) to state that this
is about the RGMII clock
- added Jerome's Reviewed-by to PATCH #2 (formerly PATCH #1)
- replaced PATCH #3 (formerly PATCH #2) with one that sets
CLK_SET_RATE_PARENT on the mux and thus re-configures the MPLL2 clock
on Meson8b correctly
[0] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005596.html
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005848.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005861.html
[3] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005899.html
[4] http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006125.html
====================
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Meson8b the only valid input clock is MPLL2. The bootloader
configures that to run at 500002394Hz which cannot be divided evenly
down to 125MHz using the m250_div clock. Currently the common clock
framework chooses a m250_div of 2 - with the internal fixed
"divide by 10" this results in a RGMII TX clock of 125001197Hz (120Hz
above the requested 125MHz).
Letting the common clock framework propagate the rate changes up to the
parent of m250_mux allows us to get the best possible clock rate. With
this patch the common clock framework calculates a rate of
very-close-to-250MHz (249999701Hz to be exact) for the MPLL2 clock
(which is the mux input). Dividing that by 2 (which is an internal,
fixed divider for the RGMII TX clock) gives us an RGMII TX clock of
124999850Hz (which is only 150Hz off the requested 125MHz, compared to
1197Hz based on the MPLL2 rate set by u-boot and the Amlogic GPL kernel
sources).
SoCs from the Meson GX series are not affected by this change because
the input clock is FCLK_DIV2 whose rate cannot be changed (which is fine
since it's running at 1GHz, so it's already a multiple of 250MHz and
125MHz).
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Meson8b only supports MPLL2 as clock input. The rate of the MPLL2 clock
set by Odroid-C1's u-boot is close to (but not exactly) 500MHz. The
exact rate is 500002394Hz, which is calculated in
drivers/clk/meson/clk-mpll.c using the following formula:
DIV_ROUND_UP_ULL((u64)parent_rate * SDM_DEN, (SDM_DEN * n2) + sdm)
Odroid-C1's u-boot configures MPLL2 with the following values:
- SDM_DEN = 16384
- SDM = 1638
- N2 = 5
The 250MHz clock (m250_div) inside dwmac-meson8b driver is derived from
the MPLL2 clock. Due to MPLL2 running slightly faster than 500MHz the
common clock framework chooses a divider which is too big to generate
the 250MHz clock (a divider of 2 would be needed, but this is rounded up
to a divider of 3). This breaks the RTL8211F RGMII PHY on Odroid-C1
because it requires a (close to) 125MHz RGMII TX clock (on Gbit speeds,
the IP block internally divides that down to 25MHz on 100Mbit/s
connections and 2.5MHz on 10Mbit/s connections - we don't need any
special configuration for that).
Round the divider to the closest value to prevent this issue on Meson8b.
This means we'll now end up with a clock rate for the RGMII TX clock of
125001197Hz (= 125MHz plus 1197Hz), which is close-enough to 125MHz.
This has no effect on the Meson GX SoCs since there fclk_div2 is used as
input clock, which has a rate of 1000MHz (and thus is divisible cleanly
to 250MHz and 125MHz).
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tests (using an oscilloscope and an Odroid-C1 board with a RTL8211F
RGMII PHY) have shown that the PRG_ETH0 register behaves as follows:
- bit 4 is a mux to choose between two parent clocks. according to the
public S805 datasheet the only supported parent clock is MPLL2 (this
was not verified using the oscilloscope).
The public S805/S905 datasheet claims that this bit is reserved.
- bits 9:7 control a one-based divider (register value 1 means "divide
by 1", etc.) for the input clock. we call this clock the "m250_div"
clock because it's value is always supposed to be (close to) 250MHz
(see below for an explanation).
The description in the public S805/S905 datasheet is a bit cryptic,
but it comes down to "input clock = 250MHz * value" (which could also
be expressed as "250MHz = input clock / value")
- there seems to be an internal fixed divide-by-2 clock which takes the
output from the m250_div and divides it by 2. This is not unusual on
Amlogic SoCs, since the SDIO (MMC) driver also uses an internal fixed
divide-by-2 clock.
This is not documented in the public S805/S905 datasheet
- bit 10 controls a gate clock which enables or disables the RGMII TX
clock (which is an output on the MAC/SoC and an input in the PHY). we
call this the "rgmii_tx_en" clock. if this bit is set to "0" the RGMII
TX clock output is close to 0
The description for this bit in the public S805/S905 datasheet is
"Generate 25MHz clock for PHY". Based on these tests it's believed
that this is wrong, and should probably read "Generate the 125MHz
RGMII TX clock for the PHY"
- the RGMII TX clock has to be set to 125MHz - the IP block adjusts the
output (automatically) depending on the line speed (RGMII specifies
that Gbit connections use a 125MHz clock, 100Mbit/s connections use a
25MHz clock and 10Mbit/s connections use a 2.5MHz clock. only Gbit and
100Mbit/s were tested with an oscilloscope). Due to the requirement
that this clock always has to be set to 125MHz and due to the fixed
divide-by-2 parent clock this means that m250_div will always end up
with a rate of (close to) 250MHz.
- bits 6:5 are the TX delay, which is also named "clock phase" in some
of Amlogic's older GPL kernel sources.
The PHY also has an XTAL_IN pin where a 25MHz clock has to be provided.
Tests with the oscilloscope have shown that this is routed to a crystal
right next to the RTL8211F PHY. The same seems to be true on the Khadas
VIM2 (which uses a GXM SoC) board - however the 25MHz crystal is on the
other side of the PCB there.
This updates the clocks in the dwmac-meson8b driver by replacing the
"m25_div" with the "rgmii_tx_en" clock and additionally introducing a
fixed divide-by-2 clock between "m250_div" and "rgmii_tx_en".
Now we also need to set a frequency of 125MHz on the RGMII clock
(opposed to the 25MHz we set before, with that non-existing
divide-by-5-or-10 divider).
Special thanks go to Linus Lüssing for testing the various bits and
checking the results with an oscilloscope on his Odroid-C1!
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neither the m25_div_clk nor the m250_div_clk or m250_mux_clk are used in
RMII mode. The m25_div_clk output is routed to the RGMII PHY's "RGMII
clock".
This means that we don't need to configure the clocks in RMII mode. The
driver however did this - with no effect since the clocks are not routed
to the PHY in RMII mode.
While here also rename meson8b_init_clk to meson8b_init_rgmii_tx_clk to
make it easier to understand the code.
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0dfb33a0d7e2 ("sch_red: report backlog information") copied
child's backlog into RED's backlog. Back then RED did not maintain
its own backlog counts. This has changed after commit 2ccccf5fb43f
("net_sched: update hierarchical backlog too") and commit d7f4f332f082
("sch_red: update backlog as well"). Copying is no longer necessary.
Tested:
$ tc -s qdisc show dev veth0
qdisc red 1: root refcnt 2 limit 400000b min 30000b max 30000b ecn
Sent 20942 bytes 221 pkt (dropped 0, overlimits 0 requeues 0)
backlog 1260b 14p requeues 14
marked 0 early 0 pdrop 0 other 0
qdisc tbf 2: parent 1: rate 1Kbit burst 15000b lat 3585.0s
Sent 20942 bytes 221 pkt (dropped 0, overlimits 138 requeues 0)
backlog 1260b 14p requeues 14
Recently RED offload was added. We need to make sure drivers don't
depend on resetting the stats. This means backlog should be treated
like any other statistic:
total_stat = new_hw_stat - prev_hw_stat;
Adjust mlxsw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Nogah Frankel <nogahf@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The latest merge between net and net-next introduced a complier assert in
mlx5 driver. In hca_cap_bits older fields are kept along with newer
fields that should have replaced them.
Fixes: c02b3741eb99 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping changes all over.
The mini-qdisc bits were a little bit tricky, however.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-01-17
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add initial BPF map offloading for nfp driver. Currently only
programs were supported so far w/o being able to access maps.
Offloaded programs are right now only allowed to perform map
lookups, and control path is responsible for populating the
maps. BPF core infrastructure along with nfp implementation is
provided, from Jakub.
2) Various follow-ups to Josef's BPF error injections. More
specifically that includes: properly check whether the error
injectable event is on function entry or not, remove the percpu
bpf_kprobe_override and rather compare instruction pointer
with original one, separate error-injection from kprobes since
it's not limited to it, add injectable error types in order to
specify what is the expected type of failure, and last but not
least also support the kernel's fault injection framework, all
from Masami.
3) Various misc improvements and cleanups to the libbpf Makefile.
That is, fix permissions when installing BPF header files, remove
unused variables and functions, and also install the libbpf.h
header, from Jesper.
4) When offloading to nfp JIT and the BPF insn is unsupported in the
JIT, then reject right at verification time. Also fix libbpf with
regards to ELF section name matching by properly treating the
program type as prefix. Both from Quentin.
5) Add -DPACKAGE to bpftool when including bfd.h for the disassembler.
This is needed, for example, when building libfd from source as
bpftool doesn't supply a config.h for bfd.h. Fix from Jiong.
6) xdp_convert_ctx_access() is simplified since it doesn't need to
set target size during verification, from Jesper.
7) Let bpftool properly recognize BPF_PROG_TYPE_CGROUP_DEVICE
program types, from Roman.
8) Various functions in BPF cpumap were not declared static, from Wei.
9) Fix a double semicolon in BPF samples, from Luis.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull rdma fixes from Doug Ledford:
"We had a few more items creep up over the last week. Given we are in
-rc8, these are obviously limited to bugs that have a big downside and
for which we are certain of the fix.
The first is a straight up oops bug that all you have to do is read
the code to see it's a guaranteed 100% oops bug.
The second is a use-after-free issue. We get away lucky if the queue
we are shutting down is empty, but if it isn't, we can end up oopsing.
We really need to drain the queue before destroying it.
The final one is an issue with bad user input causing us to access our
port array out of bounds. While fixing the array out of bounds issue,
it was noticed that the original code did the same thing twice (the
call to rdma_ah_set_port_num()), so its removal is not balanced by a
readd elsewhere, it was already where it needed to be in addition to
where it didn't need to be.
Summary:
- Oops fix in hfi1 driver
- use-after-free issue in iser-target
- use of user supplied array index without proper checking"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix out-of-bound access while querying AH
IB/hfi1: Prevent a NULL dereference
iser-target: Fix possible use-after-free in connection establishment error
|
|
Jesper Dangaard Brouer says:
====================
This patchset contains some small improvements and cleanup for
the Makefile in tools/lib/bpf/.
It worries me that the libbpf.so shared library is not versioned,
but it not addressed in this patchset.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The third parameter to do_install was not used by $(INSTALL) command.
Fix this by only setting the -m option when the third parameter is supplied.
The use of a third parameter was introduced in commit eb54e522a000 ("bpf:
install libbpf headers on 'make install'").
Without this change, the header files are install as executables files (755).
Fixes: eb54e522a000 ("bpf: install libbpf headers on 'make install'")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The plugin_dir_SQ variable is not used, remove it.
The function update_dir is also unused, remove it.
The variable $VERSION_FILES is empty, remove it.
These all originates from the introduction of the Makefile, and is likely a copy paste
from tools/lib/traceevent/Makefile.
Fixes: 1b76c13e4b36 ("bpf tools: Introduce 'bpf' library and add bpf feature check")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
It seems like an oversight not to install the header file for libbpf,
given the libbpf.so + libbpf.a files are installed.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Jakub Kicinski says:
====================
This series combines a number of random improvements ranging from
libbpf to nfp driver. NFP patches make better use of the verifier
log. There is a requested adjustment to the map offload code, and
a warning fix for a W=1 build to the disassembler. Quentin also
fixes the libbpf program type detection, while Jiong allows the use
of libbfd compiled from source.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
If an eBPF instruction is unknown to the driver JIT compiler, we can
reject the program at verification time.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Use the verifier log to output error messages if map lookup
can't be offloaded.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
libbpf is able to deduce the type of a program from the name of the ELF
section in which it is located. However, the comparison is made on the
first n characters, n being determined with sizeof() applied to the
reference string (e.g. "xdp"). When such section names are supposed to
receive a suffix separated with a slash (e.g. "kprobe/"), using sizeof()
takes the final NUL character of the reference string into account,
which implies that both strings must be equal. Instead, the desired
behaviour would consist in taking the length of the string, *without*
accounting for the ending NUL character, and to make sure the reference
string is a prefix to the ELF section name.
Subtract 1 to the total size of the string for obtaining the length for
the comparison.
Fixes: 583c90097f72 ("libbpf: add ability to guess program type based on section name")
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
bfd.h is requiring including of config.h except when PACKAGE or
PACKAGE_VERSION are defined.
/* PR 14072: Ensure that config.h is included first. */
#if !defined PACKAGE && !defined PACKAGE_VERSION
#error config.h must be included before this header
#endif
This check has been introduced since May-2012. It doesn't show up in bfd.h
on some Linux distribution, probably because distributions have remove it
when building the package.
However, sometimes the user might just build libfd from source code then
link bpftool against it. For this case, bfd.h will be original that we need
to define PACKAGE or PACKAGE_VERSION.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Functions of type bpf_insn_print_t take printf-like format
string, mark the type accordingly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Daniel suggests it would be more logical for bpf_offload_dev_match()
to return false is either the program or the map are not offloaded,
rather than treating the both not offloaded case as a "matching
CPU/host device".
This makes no functional difference today, since verifier only calls
bpf_offload_dev_match() when one of the objects is offloaded.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Fixes the following sparse warnings:
kernel/bpf/cpumap.c:146:6: warning:
symbol '__cpu_map_queue_destructor' was not declared. Should it be static?
kernel/bpf/cpumap.c:225:16: warning:
symbol 'cpu_map_build_skb' was not declared. Should it be static?
kernel/bpf/cpumap.c:340:26: warning:
symbol '__cpu_map_entry_alloc' was not declared. Should it be static?
kernel/bpf/cpumap.c:398:6: warning:
symbol '__cpu_map_entry_free' was not declared. Should it be static?
kernel/bpf/cpumap.c:441:6: warning:
symbol '__cpu_map_entry_replace' was not declared. Should it be static?
kernel/bpf/cpumap.c:454:5: warning:
symbol 'cpu_map_delete_elem' was not declared. Should it be static?
kernel/bpf/cpumap.c:467:5: warning:
symbol 'cpu_map_update_elem' was not declared. Should it be static?
kernel/bpf/cpumap.c:505:6: warning:
symbol 'cpu_map_free' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pull networking fixes from David Miller:
1) Two read past end of buffer fixes in AF_KEY, from Eric Biggers.
2) Memory leak in key_notify_policy(), from Steffen Klassert.
3) Fix overflow with bpf arrays, from Daniel Borkmann.
4) Fix RDMA regression with mlx5 due to mlx5 no longer using
pci_irq_get_affinity(), from Saeed Mahameed.
5) Missing RCU read locking in nl80211_send_iface() when it calls
ieee80211_bss_get_ie(), from Dominik Brodowski.
6) cfg80211 should check dev_set_name()'s return value, from Johannes
Berg.
7) Missing module license tag in 9p protocol, from Stephen Hemminger.
8) Fix crash due to too small MTU in udp ipv6 sendmsg, from Mike
Maloney.
9) Fix endless loop in netlink extack code, from David Ahern.
10) TLS socket layer sets inverted error codes, resulting in an endless
loop. From Robert Hering.
11) Revert openvswitch erspan tunnel support, it's mis-designed and we
need to kill it before it goes into a real release. From William Tu.
12) Fix lan78xx failures in full speed USB mode, from Yuiko Oshino.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
net, sched: fix panic when updating miniq {b,q}stats
qed: Fix potential use-after-free in qed_spq_post()
nfp: use the correct index for link speed table
lan78xx: Fix failure in USB Full Speed
sctp: do not allow the v4 socket to bind a v4mapped v6 address
sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
sctp: reinit stream if stream outcnt has been change by sinit in sendmsg
ibmvnic: Fix pending MAC address changes
netlink: extack: avoid parenthesized string constant warning
ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
net: Allow neigh contructor functions ability to modify the primary_key
sh_eth: fix dumping ARSTR
Revert "openvswitch: Add erspan tunnel support."
net/tls: Fix inverted error codes to avoid endless loop
ipv6: ip6_make_skb() needs to clear cork.base.dst
sctp: avoid compiler warning on implicit fallthru
net: ipv4: Make "ip route get" match iif lo rules again.
netlink: extack needs to be reset each time through loop
tipc: fix a memory leak in tipc_nl_node_get_link()
ipv6: fix udpv6 sendmsg crash caused by too small MTU
...
|
|
Currently in the cases where cmp_type == CMP_TYPE_RX_L2_TPA_START_CMP or
CMP_TYPE_RX_L2_TPA_END_CMP the exit path updates cpr->rx_bytes with an
uninitialized length len. Fix this by adding a new exit path that does
not update the cpr stats with the bogus length len and remove the unused
label next_rx_no_prod.
Detected by CoverityScan, CID#1463807 ("Uninitialized scalar variable")
Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few small last-minute fixes that should sneak into 4.15:
- remove a spurious WARN_ON() triggered by syzkaller
- fix for ioctl races in ALSA sequencer
- two trivial HD-audio fixup entries"
* tag 'sound-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Make ioctls race-free
ALSA: pcm: Remove yet superfluous WARN_ON()
ALSA: hda - Apply the existing quirk to iMac 14,1
ALSA: hda - Apply headphone noise quirk for another Dell XPS 13 variant
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Bring back context level recursive protection in ring buffer.
The simpler counter protection failed, due to a path when tracing
with trace_clock_global() as it could not be reentrant and depended
on the ring buffer recursive protection to keep that from happening.
- Prevent branch profiling when FORTIFY_SOURCE is enabled.
It causes 50 - 60 MB in warning messages. Branch profiling should
never be run on production systems, so there's no reason that it
needs to be enabled with FORTIFY_SOURCE.
* tag 'trace-v4.15-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Prevent PROFILE_ALL_BRANCHES when FORTIFY_SOURCE=y
ring-buffer: Bring back context level recursive checks
|
|
While working on fixing another bug, I ran into the following panic
on arm64 by simply attaching clsact qdisc, adding a filter and running
traffic on ingress to it:
[...]
[ 178.188591] Unable to handle kernel read from unreadable memory at virtual address 810fb501f000
[ 178.197314] Mem abort info:
[ 178.200121] ESR = 0x96000004
[ 178.203168] Exception class = DABT (current EL), IL = 32 bits
[ 178.209095] SET = 0, FnV = 0
[ 178.212157] EA = 0, S1PTW = 0
[ 178.215288] Data abort info:
[ 178.218175] ISV = 0, ISS = 0x00000004
[ 178.222019] CM = 0, WnR = 0
[ 178.224997] user pgtable: 4k pages, 48-bit VAs, pgd = 0000000023cb3f33
[ 178.231531] [0000810fb501f000] *pgd=0000000000000000
[ 178.236508] Internal error: Oops: 96000004 [#1] SMP
[...]
[ 178.311855] CPU: 73 PID: 2497 Comm: ping Tainted: G W 4.15.0-rc7+ #5
[ 178.319413] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB18A 03/31/2017
[ 178.326887] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 178.331685] pc : __netif_receive_skb_core+0x49c/0xac8
[ 178.336728] lr : __netif_receive_skb+0x28/0x78
[ 178.341161] sp : ffff00002344b750
[ 178.344465] x29: ffff00002344b750 x28: ffff810fbdfd0580
[ 178.349769] x27: 0000000000000000 x26: ffff000009378000
[...]
[ 178.418715] x1 : 0000000000000054 x0 : 0000000000000000
[ 178.424020] Process ping (pid: 2497, stack limit = 0x000000009f0a3ff4)
[ 178.430537] Call trace:
[ 178.432976] __netif_receive_skb_core+0x49c/0xac8
[ 178.437670] __netif_receive_skb+0x28/0x78
[ 178.441757] process_backlog+0x9c/0x160
[ 178.445584] net_rx_action+0x2f8/0x3f0
[...]
Reason is that sch_ingress and sch_clsact are doing mini_qdisc_pair_init()
which sets up miniq pointers to cpu_{b,q}stats from the underlying qdisc.
Problem is that this cannot work since they are actually set up right after
the qdisc ->init() callback in qdisc_create(), so first packet going into
sch_handle_ingress() tries to call mini_qdisc_bstats_cpu_update() and we
therefore panic.
In order to fix this, allocation of {b,q}stats needs to happen before we
call into ->init(). In net-next, there's already such option through commit
d59f5ffa59d8 ("net: sched: a dflt qdisc may be used with per cpu stats").
However, the bug needs to be fixed in net still for 4.15. Thus, include
these bits to reduce any merge churn and reuse the static_flags field to
set TCQ_F_CPUSTATS, and remove the allocation from qdisc_create() since
there is no other user left. Prashant Bhole ran into the same issue but
for net-next, thus adding him below as well as co-author. Same issue was
also reported by Sandipan Das when using bcc.
Fixes: 46209401f8f6 ("net: core: introduce mini_Qdisc and eliminate usage of tp->q for clsact fastpath")
Reference: https://lists.iovisor.org/pipermail/iovisor-dev/2018-January/001190.html
Reported-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Co-authored-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Co-authored-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612f0b0adb6046f19b906609e4fe8b1ba
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to check if p_ent->comp_mode is QED_SPQ_MODE_EBLOCK before
calling qed_spq_add_entry(). The test is fine is the mode is EBLOCK,
but if it isn't then qed_spq_add_entry() might kfree(p_ent).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like qdisc_lookup_class() never existed in the tree
in the git era. Remove the prototype from the header.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sts variable is holding link speed as well as state. We should
be using ls to index into ls_to_ethtool.
Fixes: 265aeb511bd5 ("nfp: add support for .get_link_ksettings()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix initialize the uninitialized tx_qlen to an appropriate value when USB
Full Speed is used.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have identified a race condition during reception of socket
events and messages in the topology server.
- The function tipc_close_conn() is releasing the corresponding
struct tipc_subscriber instance without considering that there
may still be items in the receive work queue. When those are
scheduled, in the function tipc_receive_from_work(), they are
using the subscriber pointer stored in struct tipc_conn, without
first checking if this is valid or not. This will sometimes
lead to crashes, as the next call of tipc_conn_recvmsg() will
access the now deleted item.
We fix this by making the usage of this pointer conditional on
whether the connection is active or not. I.e., we check the condition
test_bit(CF_CONNECTED) before making the call tipc_conn_recvmsg().
- Since the two functions may be running on different cores, the
condition test described above is not enough. tipc_close_conn()
may come in between and delete the subscriber item after the condition
test is done, but before tipc_conn_recv_msg() is finished. This
happens less frequently than the problem described above, but leads
to the same symptoms.
We fix this by using the existing sk_callback_lock for mutual
exclusion in the two functions. In addition, we have to move
a call to tipc_conn_terminate() outside the mentioned lock to
avoid deadlock.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Igor Russkikh says:
====================
Aquantia atlantic driver update 2018/01
This patch is a set of cleanups and bugfixes in preparation to new
Aquantia hardware support.
Standard ARRAY_SIZE is now used through all the code,
some unused abstraction structures removed and cleaned up,
duplicate declarations removed.
Also two large declaration styling fixes:
- Hardware register set defines are lined up with kernel style
- Hardware access functions were not prefixed, now already
defined hw_atl prefix is used.
patch v2 changes:
- patch reorganized because of its big size. New HW support
will be submitted as a separate patchset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb len should be fetched before gro_receive - otherwise we may get
wrong or even outdated skb data.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Internal functions for registers and HW access were not prefixed.
This introduce noise in global kernel symbols. Here we add explicit prefix
'hw_atl' to all the HW access layer functions.
Alignment and styling were fixed as well.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Original driver code had internal registers and masks declarations
in low case and without any prefix.
Here we make all these uppercase and add already used HW_ATL prefix
to recognize these.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
aq_nic_s was hidden in aq_nic_internal.h, that made it difficult to access
nic fields and structures from other modules.
This change moves aq_nic_s struct into aq_nic.h and thus makes it available
to other driver modules, mainly pci module and hw related module.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate useless passing of net_device_ops and ethtools_ops through
deep chain of calls.
Move all pci related code into aq_pci_func module.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware operations and capabilities tables are constants and
never changed. Declare these as constants.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use direct aq_hw_s *self reference where possible
Eliminate useless abstraction PHAL, duplicated structures definitions,
Simplify nic config structure creation and management.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Usage of aq_obj_s structure is noop, here we remove it
replacing access to flags filed directly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aleksey Makarov says:
====================
net: thunderx: add support for PTP clock
This series adds support for IEEE 1588 Precision Time Protocol
to Cavium ethernet driver.
The first patch adds support for the Precision Time Protocol Clocks and
Timestamping coprocessor (PTP) found on Cavium processors.
It registers a new PTP clock in the PTP core and provides functions
to use the counter in BGX, TNS, GTI, and NIC blocks.
The second patch introduces support for the PTP protocol to the
Cavium ThunderX ethernet driver.
v6:
- check if ptp_clock_register() returns NULL (Richard Cochran)
- fix doc comment for cavium_ptp_enable() (Richard Cochran)
- fix a function call formatting; use defined constant (Richard Cochran)
- add comments for `tx_ptp_skbs` and `ptp_skb` (Richard Cochran)
- use adjfine() instead of adjfreq() (Richard Cochran)
- add Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
v5: https://lkml.kernel.org/r/20171211141435.2915-1-aleksey.makarov@cavium.com
- fix the file headers (add SPDX tags, remove advertisment) (Philippe Ombredanne)
- use "imply" instead of "select" (Richard Cochran)
- add some code in cavium_ptp_get() for the case when the PTP driver has not been
registered with the PTP core
v4: https://lkml.kernel.org/r/20171208103442.19354-1-aleksey.makarov@cavium.com
- use IS_ENABLED. This fixes compilation of the ptp as a module (David Miller)
- select PTP_1588_CLOCK, not depend on it. This fixes a build warning.
- change u64 to __be64. This fixes the sparse warning
"warning: cast to restricted __be64"
- make nicvf_config_hwtstamp() static. This fixes the sparse warning
"warning: symbol 'nicvf_config_hwtstamp' was not declared. Should it be static?"
v3: https://lkml.kernel.org/r/20171206133100.26436-1-aleksey.makarov@cavium.com
- rebase to net-next
v2: https://lkml.kernel.org/r/20171117134909.8954-1-aleksey.makarov@cavium.com
- use readq()/writeq() in place of cavium_ptp_reg_read()/cavium_ptp_reg_write(),
don't use readq_relaxed()/writeq_relaxed() (David Daney)
v1: https://lkml.kernel.org/r/20171107190704.15458-1-aleksey.makarov@cavium.com
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds timestamping support for both receive and transmit
paths. On the receive side no filters are supported i.e either
all pkts will get a timestamp appended infront of the packet or none.
On the transmit side HW doesn't support timestamp insertion but
only generates a separate CQE with transmitted packet's timestamp.
Also HW supports only one packet at a time for timestamping on the
transmit side.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the Precision Time Protocol
Clocks and Timestamping hardware found on Cavium ThunderX
processors.
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
More fixes:
* hwsim:
- properly flush deletion works at module unload
- validate # of channels passed from userspace
* cfg80211:
- fix RCU locking regression
- initialize on-stack channel data for nl80211 event
- check dev_set_name() return value
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum_qdisc.c:464:1: warning:
symbol 'mlxsw_sp_qdisc_prio_unoffload' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
