Age | Commit message (Collapse) | Author |
|
__get_kernel_nofault() does copy data in supervisor mode when
forcing a task backtrace log through /proc/sysrq_trigger.
This is expected cause a bus error exception on e.g. NULL
pointer dereferencing when logging a kernel task has no
workqueue associated. This bus error ought to be ignored.
Our 030 bus error handler is ill equipped to deal with this:
Whenever ssw indicates a kernel mode access on a data fault,
we don't even attempt to handle the fault and instead always
send a SEGV signal (or panic). As a result, the check
for exception handling at the fault PC (buried in
send_sig_fault() which gets called from do_page_fault()
eventually) is never used.
In contrast, both 040 and 060 access error handlers do not
care whether a fault happened on supervisor mode access,
and will call do_page_fault() on those, ultimately honoring
the exception table.
Add a check in bus_error030 to call do_page_fault() in case
we do have an entry for the fault PC in our exception table.
I had attempted a fix for this earlier in 2019 that did rely
on testing pagefault_disabled() (see link below) to achieve
the same thing, but this patch should be more generic.
Tested on 030 Atari Falcon.
Reported-by: Eero Tamminen <oak@helsinkinet.fi>
Link: https://lore.kernel.org/r/alpine.LNX.2.21.1904091023540.25@nippy.intranet
Link: https://lore.kernel.org/r/63130691-1984-c423-c1f2-73bfd8d3dcd3@gmail.com
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230301021107.26307-1-schmitzmic@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
When booting with an initial ramdisk on platforms where physical memory
does not start at address zero (e.g. on Amiga):
initrd: 0ef0602c - 0f800000
Zone ranges:
DMA [mem 0x0000000008000000-0x000000f7ffffffff]
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000008000000-0x000000000f7fffff]
Initmem setup node 0 [mem 0x0000000008000000-0x000000000f7fffff]
Unable to handle kernel access at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<00201d3c>] memcmp+0x28/0x56
As phys_to_virt() relies on m68k_memoffset and module_fixup(), it must
not be called before paging_init(). Hence postpone the phys_to_virt
handling for the initial ramdisk until after calling paging_init().
While at it, reduce #ifdef clutter by using IS_ENABLED() instead.
Fixes: 376e3fdecb0dcae2 ("m68k: Enable memtest functionality")
Reported-by: Stephen Walsh <vk3heg@vk3heg.net>
Link: https://lists.debian.org/debian-68k/2022/09/msg00007.html
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/4f45f05f377bf3f5baf88dbd5c3c8aeac59d94f0.camel@physik.fu-berlin.de
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/dff216da09ab7a60217c3fc2147e671ae07d636f.1677528627.git.geert@linux-m68k.org
|
|
The calculation of end addresses of memory chunks overflowed to 0 when
a memory chunk is located at the end of 32-bit address space.
This is the case for the HP300 architecture.
Link: https://lore.kernel.org/linux-m68k/CACz-3rhUo5pgNwdWHaPWmz+30Qo9xCg70wNxdf7o5x-6tXq8QQ@mail.gmail.com/
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230223112349.26675-1-jongk@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The xtables packet traverser performs an unconditional local_bh_disable(),
but the nf_tables evaluation loop does not.
Functions that are called from either xtables or nftables must assume
that they can be called in process context.
inet_twsk_deschedule_put() assumes that no softirq interrupt can occur.
If tproxy is used from nf_tables its possible that we'll deadlock
trying to aquire a lock already held in process context.
Add a small helper that takes care of this and use it.
Link: https://lore.kernel.org/netfilter-devel/401bd6ed-314a-a196-1cdc-e13c720cc8f2@balasys.hu/
Fixes: 4ed8eb6570a4 ("netfilter: nf_tables: Add native tproxy support")
Reported-and-tested-by: Major Dávid <major.david@balasys.hu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
It seems that change was unintentional, we have userspace code that
needs the mark while listening for events like REPLY, DESTROY, etc.
Also include 0-marks in requested dumps, as they were before that fix.
Fixes: 1feeae071507 ("netfilter: ctnetlink: fix compilation warning after data race fixes in ct mark")
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Following warning reported by KASAN during driver unload
==================================================================
BUG: KASAN: double-free in bnxt_remove_one+0x103/0x200 [bnxt_en]
Free of addr ffff88814e8dd4c0 by task rmmod/17469
CPU: 47 PID: 17469 Comm: rmmod Kdump: loaded Tainted: G S 6.2.0-rc7+ #2
Hardware name: Dell Inc. PowerEdge R740/01YM03, BIOS 2.3.10 08/15/2019
Call Trace:
<TASK>
dump_stack_lvl+0x33/0x46
print_report+0x17b/0x4b3
? __call_rcu_common.constprop.79+0x27e/0x8c0
? __pfx_free_object_rcu+0x10/0x10
? __virt_addr_valid+0xe3/0x160
? bnxt_remove_one+0x103/0x200 [bnxt_en]
kasan_report_invalid_free+0x64/0xd0
? bnxt_remove_one+0x103/0x200 [bnxt_en]
? bnxt_remove_one+0x103/0x200 [bnxt_en]
__kasan_slab_free+0x179/0x1c0
? bnxt_remove_one+0x103/0x200 [bnxt_en]
__kmem_cache_free+0x194/0x350
bnxt_remove_one+0x103/0x200 [bnxt_en]
pci_device_remove+0x62/0x110
device_release_driver_internal+0xf6/0x1c0
driver_detach+0x76/0xe0
bus_remove_driver+0x89/0x160
pci_unregister_driver+0x26/0x110
? strncpy_from_user+0x188/0x1c0
bnxt_exit+0xc/0x24 [bnxt_en]
__x64_sys_delete_module+0x21f/0x390
? __pfx___x64_sys_delete_module+0x10/0x10
? __pfx_mem_cgroup_handle_over_high+0x10/0x10
? _raw_spin_lock+0x87/0xe0
? __pfx__raw_spin_lock+0x10/0x10
? __audit_syscall_entry+0x185/0x210
? ktime_get_coarse_real_ts64+0x51/0x80
? syscall_trace_enter.isra.18+0x126/0x1a0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7effcb6fd71b
Code: 73 01 c3 48 8b 0d 6d 17 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 17 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffeada270b8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 00005623660e0750 RCX: 00007effcb6fd71b
RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005623660e07b8
RBP: 0000000000000000 R08: 00007ffeada26031 R09: 0000000000000000
R10: 00007effcb771280 R11: 0000000000000206 R12: 00007ffeada272e0
R13: 00007ffeada28bc4 R14: 00005623660e02a0 R15: 00005623660e0750
</TASK>
Auxiliary device structures are freed in bnxt_aux_dev_release. So avoid
calling kfree from bnxt_remove_one.
Also, set bp->edev to NULL before freeing the auxilary private structure.
Fixes: d80d88b0dfff ("bnxt_en: Add auxiliary driver support")
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to keep track of all the possible concurrent TPA (GRO/LRO)
completions on the aggregation ring. On P5 chips, the maximum number
of concurrent TPA is 256 and the amount of memory we allocate is order-5
on systems using 4K pages. Memory allocation failure has been reported:
NetworkManager: page allocation failure: order:5, mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 15 PID: 2995 Comm: NetworkManager Kdump: loaded Not tainted 5.10.156 #1
Hardware name: Dell Inc. PowerEdge R660/0M1CC5, BIOS 0.2.25 08/12/2022
Call Trace:
dump_stack+0x57/0x6e
warn_alloc.cold.120+0x7b/0xdd
? _cond_resched+0x15/0x30
? __alloc_pages_direct_compact+0x15f/0x170
__alloc_pages_slowpath.constprop.108+0xc58/0xc70
__alloc_pages_nodemask+0x2d0/0x300
kmalloc_order+0x24/0xe0
kmalloc_order_trace+0x19/0x80
bnxt_alloc_mem+0x1150/0x15c0 [bnxt_en]
? bnxt_get_func_stat_ctxs+0x13/0x60 [bnxt_en]
__bnxt_open_nic+0x12e/0x780 [bnxt_en]
bnxt_open+0x10b/0x240 [bnxt_en]
__dev_open+0xe9/0x180
__dev_change_flags+0x1af/0x220
dev_change_flags+0x21/0x60
do_setlink+0x35c/0x1100
Instead of allocating this big chunk of memory and dividing it up for the
concurrent TPA instances, allocate each small chunk separately for each
TPA instance. This will reduce it to order-0 allocations.
Fixes: 79632e9ba386 ("bnxt_en: Expand bnxt_tpa_info struct to support 57500 chips.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The locking in phy_probe() and phy_remove() does very little to prevent
any races with e.g. phy_attach_direct(), but instead causes lockdep ABBA
warnings. Remove it.
======================================================
WARNING: possible circular locking dependency detected
6.2.0-dirty #1108 Tainted: G W E
------------------------------------------------------
ip/415 is trying to acquire lock:
ffff5c268f81ef50 (&dev->lock){+.+.}-{3:3}, at: phy_attach_direct+0x17c/0x3a0 [libphy]
but task is already holding lock:
ffffaef6496cb518 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x154/0x560
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.}-{3:3}:
__lock_acquire+0x35c/0x6c0
lock_acquire.part.0+0xcc/0x220
lock_acquire+0x68/0x84
__mutex_lock+0x8c/0x414
mutex_lock_nested+0x34/0x40
rtnl_lock+0x24/0x30
sfp_bus_add_upstream+0x34/0x150
phy_sfp_probe+0x4c/0x94 [libphy]
mv3310_probe+0x148/0x184 [marvell10g]
phy_probe+0x8c/0x200 [libphy]
call_driver_probe+0xbc/0x15c
really_probe+0xc0/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__device_attach_driver+0xc4/0x160
bus_for_each_drv+0x80/0xe0
__device_attach+0xb0/0x1f0
device_initial_probe+0x1c/0x2c
bus_probe_device+0xa4/0xb0
device_add+0x360/0x53c
phy_device_register+0x60/0xa4 [libphy]
fwnode_mdiobus_phy_device_register+0xc0/0x190 [fwnode_mdio]
fwnode_mdiobus_register_phy+0x160/0xd80 [fwnode_mdio]
of_mdiobus_register+0x140/0x340 [of_mdio]
orion_mdio_probe+0x298/0x3c0 [mvmdio]
platform_probe+0x70/0xe0
call_driver_probe+0x34/0x15c
really_probe+0xc0/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__driver_attach+0x104/0x210
bus_for_each_dev+0x78/0xdc
driver_attach+0x2c/0x3c
bus_add_driver+0x184/0x240
driver_register+0x80/0x13c
__platform_driver_register+0x30/0x3c
xt_compat_calc_jump+0x28/0xa4 [x_tables]
do_one_initcall+0x50/0x1b0
do_init_module+0x50/0x1fc
load_module+0x684/0x744
__do_sys_finit_module+0xc4/0x140
__arm64_sys_finit_module+0x28/0x34
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0x6c/0x1b0
do_el0_svc+0x34/0x44
el0_svc+0x48/0xf0
el0t_64_sync_handler+0xb8/0xc0
el0t_64_sync+0x1a0/0x1a4
-> #0 (&dev->lock){+.+.}-{3:3}:
check_prev_add+0xb4/0xc80
validate_chain+0x414/0x47c
__lock_acquire+0x35c/0x6c0
lock_acquire.part.0+0xcc/0x220
lock_acquire+0x68/0x84
__mutex_lock+0x8c/0x414
mutex_lock_nested+0x34/0x40
phy_attach_direct+0x17c/0x3a0 [libphy]
phylink_fwnode_phy_connect.part.0+0x70/0xe4 [phylink]
phylink_fwnode_phy_connect+0x48/0x60 [phylink]
mvpp2_open+0xec/0x2e0 [mvpp2]
__dev_open+0x104/0x214
__dev_change_flags+0x1d4/0x254
dev_change_flags+0x2c/0x7c
do_setlink+0x254/0xa50
__rtnl_newlink+0x430/0x514
rtnl_newlink+0x58/0x8c
rtnetlink_rcv_msg+0x17c/0x560
netlink_rcv_skb+0x64/0x150
rtnetlink_rcv+0x20/0x30
netlink_unicast+0x1d4/0x2b4
netlink_sendmsg+0x1a4/0x400
____sys_sendmsg+0x228/0x290
___sys_sendmsg+0x88/0xec
__sys_sendmsg+0x70/0xd0
__arm64_sys_sendmsg+0x2c/0x40
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0x6c/0x1b0
do_el0_svc+0x34/0x44
el0_svc+0x48/0xf0
el0t_64_sync_handler+0xb8/0xc0
el0t_64_sync+0x1a0/0x1a4
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(rtnl_mutex);
lock(&dev->lock);
lock(rtnl_mutex);
lock(&dev->lock);
*** DEADLOCK ***
Fixes: 298e54fa810e ("net: phy: add core phylib sfp support")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When MAC is not support PMT, driver will check PHY's WoL capability
and set device wakeup capability in stmmac_init_phy(). We can enable
the WoL through ethtool, the driver would enable the device wake up
flag. Now the device_may_wakeup() return true.
But if there is a way which enable the PHY's WoL capability derectly,
like in BIOS. The driver would not know the enable thing and would not
set the device wake up flag. The phy_suspend may failed like this:
[ 32.409063] PM: dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x50 returns -16
[ 32.409065] PM: Device stmmac-1:00 failed to suspend: error -16
[ 32.409067] PM: Some devices failed to suspend, or early wake event detected
Add to set the device wakeup enable flag according to the get_wol
function result in PHY can fix the error in this scene.
v2: add a Fixes tag.
Fixes: 1d8e5b0f3f2c ("net: stmmac: Support WOL with phy")
Signed-off-by: Rongguang Wei <weirongguang@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Commit aa47a7c215e7 ("lib/cpumask: deprecate nr_cpumask_bits") resulted
in the cpumask operations potentially becoming hugely less efficient,
because suddenly the cpumask was always considered to be variable-sized.
The optimization was then later added back in a limited form by commit
6f9c07be9d02 ("lib/cpumask: add FORCE_NR_CPUS config option"), but that
FORCE_NR_CPUS option is not useful in a generic kernel and more of a
special case for embedded situations with fixed hardware.
Instead, just re-introduce the optimization, with some changes.
Instead of depending on CPUMASK_OFFSTACK being false, and then always
using the full constant cpumask width, this introduces three different
cpumask "sizes":
- the exact size (nr_cpumask_bits) remains identical to nr_cpu_ids.
This is used for situations where we should use the exact size.
- the "small" size (small_cpumask_bits) is the NR_CPUS constant if it
fits in a single word and the bitmap operations thus end up able
to trigger the "small_const_nbits()" optimizations.
This is used for the operations that have optimized single-word
cases that get inlined, notably the bit find and scanning functions.
- the "large" size (large_cpumask_bits) is the NR_CPUS constant if it
is an sufficiently small constant that makes simple "copy" and
"clear" operations more efficient.
This is arbitrarily set at four words or less.
As a an example of this situation, without this fixed size optimization,
cpumask_clear() will generate code like
movl nr_cpu_ids(%rip), %edx
addq $63, %rdx
shrq $3, %rdx
andl $-8, %edx
callq memset@PLT
on x86-64, because it would calculate the "exact" number of longwords
that need to be cleared.
In contrast, with this patch, using a MAX_CPU of 64 (which is quite a
reasonable value to use), the above becomes a single
movq $0,cpumask
instruction instead, because instead of caring to figure out exactly how
many CPU's the system has, it just knows that the cpumask will be a
single word and can just clear it all.
Note that this does end up tightening the rules a bit from the original
version in another way: operations that set bits in the cpumask are now
limited to the actual nr_cpu_ids limit, whereas we used to do the
nr_cpumask_bits thing almost everywhere in the cpumask code.
But if you just clear bits, or scan for bits, we can use the simpler
compile-time constants.
In the process, remove 'cpumask_complement()' and 'for_each_cpu_not()'
which were not useful, and which fundamentally have to be limited to
'nr_cpu_ids'. Better remove them now than have somebody introduce use
of them later.
Of course, on x86-64 with MAXSMP there is no sane small compile-time
constant for the cpumask sizes, and we end up using the actual CPU bits,
and will generate the above kind of horrors regardless. Please don't
use MAXSMP unless you really expect to have machines with thousands of
cores.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a regression in the caam driver"
* tag 'v6.3-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - Fix edesc/iv ordering mixup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 updates from Thomas Gleixner:
"A small set of updates for x86:
- Return -EIO instead of success when the certificate buffer for SEV
guests is not large enough
- Allow STIPB to be enabled with legacy IBSR. Legacy IBRS is cleared
on return to userspace for performance reasons, but the leaves user
space vulnerable to cross-thread attacks which STIBP prevents.
Update the documentation accordingly"
* tag 'x86-urgent-2023-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
virt/sev-guest: Return -EIO if certificate buffer is not large enough
Documentation/hw-vuln: Document the interaction between IBRS and STIBP
x86/speculation: Allow enabling STIBP with legacy IBRS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"A set of updates for the interrupt susbsystem:
- Prevent possible NULL pointer derefences in
irq_data_get_affinity_mask() and irq_domain_create_hierarchy()
- Take the per device MSI lock before invoking code which relies on
it being hold
- Make sure that MSI descriptors are unreferenced before freeing
them. This was overlooked when the platform MSI code was converted
to use core infrastructure and results in a fals positive warning
- Remove dead code in the MSI subsystem
- Clarify the documentation for pci_msix_free_irq()
- More kobj_type constification"
* tag 'irq-urgent-2023-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi, platform-msi: Ensure that MSI descriptors are unreferenced
genirq/msi: Drop dead domain name assignment
irqdomain: Add missing NULL pointer check in irq_domain_create_hierarchy()
genirq/irqdesc: Make kobj_type structures constant
PCI/MSI: Clarify usage of pci_msix_free_irq()
genirq/msi: Take the per-device MSI lock before validating the control structure
genirq/ipi: Fix NULL pointer deref in irq_data_get_affinity_mask()
|
|
Pull vfs update from Al Viro:
"Adding Christian Brauner as VFS co-maintainer"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Adding VFS co-maintainer
|
|
Pull VM_FAULT_RETRY fixes from Al Viro:
"Some of the page fault handlers do not deal with the following case
correctly:
- handle_mm_fault() has returned VM_FAULT_RETRY
- there is a pending fatal signal
- fault had happened in kernel mode
Correct action in such case is not "return unconditionally" - fatal
signals are handled only upon return to userland and something like
copy_to_user() would end up retrying the faulting instruction and
triggering the same fault again and again.
What we need to do in such case is to make the caller to treat that as
failed uaccess attempt - handle exception if there is an exception
handler for faulting instruction or oops if there isn't one.
Over the years some architectures had been fixed and now are handling
that case properly; some still do not. This series should fix the
remaining ones.
Status:
- m68k, riscv, hexagon, parisc: tested/acked by maintainers.
- alpha, sparc32, sparc64: tested locally - bug has been reproduced
on the unpatched kernel and verified to be fixed by this series.
- ia64, microblaze, nios2, openrisc: build, but otherwise completely
untested"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
openrisc: fix livelock in uaccess
nios2: fix livelock in uaccess
microblaze: fix livelock in uaccess
ia64: fix livelock in uaccess
sparc: fix livelock in uaccess
alpha: fix livelock in uaccess
parisc: fix livelock in uaccess
hexagon: fix livelock in uaccess
riscv: fix livelock in uaccess
m68k: fix livelock in uaccess
|
|
include/linux/compiler-intel.h had no update in the past 3 years.
We often forget about the third C compiler to build the kernel.
For example, commit a0a12c3ed057 ("asm goto: eradicate CC_HAS_ASM_GOTO")
only mentioned GCC and Clang.
init/Kconfig defines CC_IS_GCC and CC_IS_CLANG but not CC_IS_ICC,
and nobody has reported any issue.
I guess the Intel Compiler support is broken, and nobody is caring
about it.
Harald Arnesen pointed out ICC (classic Intel C/C++ compiler) is
deprecated:
$ icc -v
icc: remark #10441: The Intel(R) C++ Compiler Classic (ICC) is
deprecated and will be removed from product release in the second half
of 2023. The Intel(R) oneAPI DPC++/C++ Compiler (ICX) is the recommended
compiler moving forward. Please transition to use this compiler. Use
'-diag-disable=10441' to disable this message.
icc version 2021.7.0 (gcc version 12.1.0 compatibility)
Arnd Bergmann provided a link to the article, "Intel C/C++ compilers
complete adoption of LLVM".
lib/zstd/common/compiler.h and lib/zstd/compress/zstd_fast.c were kept
untouched for better sync with https://github.com/facebook/zstd
Link: https://www.intel.com/content/www/us/en/developer/articles/technical/adoption-of-llvm-complete-icx.html
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"Some improvements/fixes for the newly added GXP driver and a Kconfig
dependency fix"
* tag 'i2c-for-6.3-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: gxp: fix an error code in probe
i2c: gxp: return proper error on address NACK
i2c: gxp: remove "empty" switch statement
i2c: Disable I2C_APPLE when I2C_PASEMI is a builtin
|
|
The migration code ends up temporarily stashing information of the wrong
type in unused fields of the newly allocated destination folio. That
all works fine, but gcc does complain about the pointer type mis-use:
mm/migrate.c: In function ‘__migrate_folio_extract’:
mm/migrate.c:1050:20: note: randstruct: casting between randomized structure pointer types (ssa): ‘struct anon_vma’ and ‘struct address_space’
1050 | *anon_vmap = (void *)dst->mapping;
| ~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
and gcc is actually right to complain since it really doesn't understand
that this is a very temporary special case where this is ok.
This could be fixed in different ways by just obfuscating the assignment
sufficiently that gcc doesn't see what is going on, but the truly
"proper C" way to do this is by explicitly using a union.
Using unions for type conversions like this is normally hugely ugly and
syntactically nasty, but this really is one of the few cases where we
want to make it clear that we're not doing type conversion, we're really
re-using the value bit-for-bit just using another type.
IOW, this should not become a common pattern, but in this one case using
that odd union is probably the best way to document to the compiler what
is conceptually going on here.
[ Side note: there are valid cases where we convert pointers to other
pointer types, notably the whole "folio vs page" situation, where the
types actually have fundamental commonalities.
The fact that the gcc note is limited to just randomized structures
means that we don't see equivalent warnings for those cases, but it
migth also mean that we miss other cases where we do play these kinds
of dodgy games, and this kind of explicit conversion might be a good
idea. ]
I verified that at least for an allmodconfig build on x86-64, this
generates the exact same code, apart from line numbers and assembler
comment changes.
Fixes: 64c8902ed441 ("migrate_pages: split unmap_and_move() to _unmap() and _move()")
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"17 hotfixes.
Eight are for MM and seven are for other parts of the kernel. Seven
are cc:stable and eight address post-6.3 issues or were judged
unsuitable for -stable backporting"
* tag 'mm-hotfixes-stable-2023-03-04-13-12' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mailmap: map Dikshita Agarwal's old address to his current one
mailmap: map Vikash Garodia's old address to his current one
fs/cramfs/inode.c: initialize file_ra_state
fs: hfsplus: fix UAF issue in hfsplus_put_super
panic: fix the panic_print NMI backtrace setting
lib: parser: update documentation for match_NUMBER functions
kasan, x86: don't rename memintrinsics in uninstrumented files
kasan: test: fix test for new meminstrinsic instrumentation
kasan: treat meminstrinsic as builtins in uninstrumented files
kasan: emit different calls for instrumentable memintrinsics
ocfs2: fix non-auto defrag path not working issue
ocfs2: fix defrag path triggering jbd2 ASSERT
mailmap: map Georgi Djakov's old Linaro address to his current one
mm/hwpoison: convert TTU_IGNORE_HWPOISON to TTU_HWPOISON
lib/zlib: DFLTCC deflate does not write all available bits for Z_NO_FLUSH
mm/damon/paddr: fix missing folio_put()
mm/mremap: fix dup_anon_vma() in vma_merge() case 4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Drop orphaned VAS MAINTAINERS entry
- Fix build errors with clang and KCSAN
- Avoid build errors seen with LD_DEAD_CODE_DATA_ELIMINATION together
with recordmcount
Thanks to Nathan Chancellor.
* tag 'powerpc-6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Avoid dead code/data elimination when using recordmcount
powerpc/vmlinux.lds: Add .text.asan/tsan sections
powerpc: Drop orphaned VAS MAINTAINERS entry
|
|
Support direct fixed-size (and for now, read-only) memory access when
kfunc's return type is a pointer to non-struct type. Calculate type size
and let BPF program access that many bytes directly. This is crucial for
numbers iterator.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-13-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Generalize the logic of fetching special stack slot object state using
spi (stack slot index). This will be used by STACK_ITER logic next.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-12-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
PTR_TO_MEM register without PTR_MAYBE_NULL is indeed non-null. This is
important for BPF verifier to be able to prune guaranteed not to be
taken branches. This is always the case with open-coded iterators.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-11-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move struct bpf_kfunc_call_arg_meta higher in the file and put it next
to struct bpf_call_arg_meta, so it can be used from more functions.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-10-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
r0 is important (unless called function is void-returning, but that's
taken care of by print_verifier_state() anyways) in verifier logs.
Currently for helpers we seem to print it in verifier log, but for
kfuncs we don't.
Instead of figuring out where in the maze of code we accidentally set r0
as scratched for helpers and why we don't do that for kfuncs, just
enforce that after any function call r0 is marked as scratched.
Also, perhaps, we should reconsider "scratched" terminology, as it's
mightily confusing. "Touched" would seem more appropriate. But I left
that for follow ups for now.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-9-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
It's not correct to assume that any BPF_CALL instruction is a helper
call. Fix visit_insn()'s detection of bpf_timer_set_callback() helper by
also checking insn->code == 0. For kfuncs insn->code would be set to
BPF_PSEUDO_KFUNC_CALL, and for subprog calls it will be BPF_PSEUDO_CALL.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-8-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Instead of referencing processed instruction repeatedly as insns[t]
throughout entire visit_insn() function, take a local insn pointer and
work with it in a cleaner way.
It makes enhancing this function further a bit easier as well.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-7-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Adjust log_fixup's expected buffer length to fix the test. It's pretty
finicky in its length expectation, but it doesn't break often. So just
adjust the length to work on current kernel and with follow up iterator
changes as well.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-6-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
env->test_state_freq flag can be set by user by passing
BPF_F_TEST_STATE_FREQ program flag. This is used in a bunch of selftests
to have predictable state checkpoints at every jump and so on.
Currently, bounded loop handling heuristic ignores this flag if number
of processed jumps and/or number of processed instructions is below some
thresholds, which throws off that reliable state checkpointing.
Honor this flag in all circumstances by disabling heuristic if
env->test_state_freq is set.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-5-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Allow to search for expected register state in all the verifier log
output that's related to specified instruction number.
See added comment for an example of possible situation that is happening
due to a simple enhancement done in the next patch, which fixes handling
of env->test_state_freq flag in state checkpointing logic.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-4-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Teach regsafe() logic to handle PTR_TO_MEM, PTR_TO_BUF, and
PTR_TO_TP_BUFFER similarly to PTR_TO_MAP_{KEY,VALUE}. That is, instead of
exact match for var_off and range, use tnum_in() and range_within()
checks, allowing more general verified state to subsume more specific
current state. This allows to match wider range of valid and safe
states, speeding up verification and detecting wider range of equivalent
states for upcoming open-coded iteration looping logic.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-3-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Improve stack slot state printing to provide more useful and relevant
information, especially for dynptrs. While previously we'd see something
like:
8: (85) call bpf_ringbuf_reserve_dynptr#198 ; R0_w=scalar() fp-8_w=dddddddd fp-16_w=dddddddd refs=2
Now we'll see way more useful:
8: (85) call bpf_ringbuf_reserve_dynptr#198 ; R0_w=scalar() fp-16_w=dynptr_ringbuf(ref_id=2) refs=2
I experimented with printing the range of slots taken by dynptr,
something like:
fp-16..8_w=dynptr_ringbuf(ref_id=2)
But it felt very awkward and pretty useless. So we print the lowest
address (most negative offset) only.
The general structure of this code is now also set up for easier
extension and will accommodate ITER slots naturally.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230302235015.2044271-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of various small fixes that have been gathered since the
last PR.
The majority of changes are for ASoC, and there is a small change in
ASoC PCM core, but the rest are all for driver- specific fixes /
quirks / updates"
* tag 'sound-fix-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (32 commits)
ALSA: ice1712: Delete unreachable code in aureon_add_controls()
ALSA: ice1712: Do not left ice->gpio_mutex locked in aureon_add_controls()
ALSA: hda/realtek: Add quirk for HP EliteDesk 800 G6 Tower PC
ALSA: hda/realtek: Improve support for Dell Precision 3260
ASoC: mediatek: mt8195: add missing initialization
ASoC: mediatek: mt8188: add missing initialization
ASoC: amd: yc: Add DMI entries to support HP OMEN 16-n0xxx (8A43)
ASoC: zl38060 add gpiolib dependency
ASoC: sam9g20ek: Disable capture unless building with microphone input
ASoC: mt8192: Fix range for sidetone positive gain
ASoC: mt8192: Report an error if when an invalid sidetone gain is written
ASoC: mt8192: Fix event generation for controls
ASoC: mt8192: Remove spammy log messages
ASoC: mchp-pdmc: fix poc noise at capture startup
ASoC: dt-bindings: sama7g5-pdmc: add microchip,startup-delay-us binding
ASoC: soc-pcm: add option to start DMA after DAI
ASoC: mt8183: Fix event generation for I2S DAI operations
ASoC: mt8183: Remove spammy logging from I2S DAI driver
ASoC: mt6358: Remove undefined HPx Mux enumeration values
ASoC: mt6358: Validate Wake on Voice 2 writes
...
|
|
Eduard Zingerman says:
====================
Changes v1 -> v2, suggested by Alexei:
- Resolved conflict with recent commit:
6fcd486b3a0a ("bpf: Refactor RCU enforcement in the verifier");
- Variable `ctx_access` removed in function `convert_ctx_accesses()`;
- Macro `BPF_COPY_STORE` renamed to `BPF_EMIT_STORE` and fixed to
correctly extract original store instruction class from code.
Original message follows:
The function verifier.c:convert_ctx_access() applies some rewrites to BPF
instructions that read from or write to the BPF program context.
For example, the write instruction for the `struct bpf_sockopt::retval`
field:
*(u32 *)(r1 + offsetof(struct bpf_sockopt, retval)) = r2
Is transformed to:
*(u64 *)(r1 + offsetof(struct bpf_sockopt_kern, tmp_reg)) = r9
r9 = *(u64 *)(r1 + offsetof(struct bpf_sockopt_kern, current_task))
r9 = *(u64 *)(r9 + offsetof(struct task_struct, bpf_ctx))
*(u32 *)(r9 + offsetof(struct bpf_cg_run_ctx, retval)) = r2
r9 = *(u64 *)(r1 + offsetof(struct bpf_sockopt_kern, tmp_reg))
Currently, the verifier only supports such transformations for LDX
(memory-to-register read) and STX (register-to-memory write) instructions.
Error is reported for ST instructions (immediate-to-memory write).
This is fine because clang does not currently emit ST instructions.
However, new `-mcpu=v4` clang flag is planned, which would allow to emit
ST instructions (discussed in [1]).
This patch-set adjusts the verifier to support ST instructions in
`verifier.c:convert_ctx_access()`.
The patches #1 and #2 were previously shared as part of RFC [2]. The
changes compared to that RFC are:
- In patch #1, a bug in the handling of the
`struct __sk_buff::queue_mapping` field was fixed.
- Patch #3 is added, which is a set of disassembler-based test cases for
context access rewrites. The test cases cover all fields for which the
handling code is modified in patch #1.
[1] Propose some new instructions for -mcpu=v4
https://lore.kernel.org/bpf/4bfe98be-5333-1c7e-2f6d-42486c8ec039@meta.com/
[2] RFC Support for BPF_ST instruction in LLVM C compiler
https://lore.kernel.org/bpf/20221231163122.1360813-1-eddyz87@gmail.com/
[3] v1
https://lore.kernel.org/bpf/20230302225507.3413720-1-eddyz87@gmail.com/
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Function verifier.c:convert_ctx_access() applies some rewrites to BPF
instructions that read or write BPF program context. This commit adds
machinery to allow test cases that inspect BPF program after these
rewrites are applied.
An example of a test case:
{
// Shorthand for field offset and size specification
N(CGROUP_SOCKOPT, struct bpf_sockopt, retval),
// Pattern generated for field read
.read = "$dst = *(u64 *)($ctx + bpf_sockopt_kern::current_task);"
"$dst = *(u64 *)($dst + task_struct::bpf_ctx);"
"$dst = *(u32 *)($dst + bpf_cg_run_ctx::retval);",
// Pattern generated for field write
.write = "*(u64 *)($ctx + bpf_sockopt_kern::tmp_reg) = r9;"
"r9 = *(u64 *)($ctx + bpf_sockopt_kern::current_task);"
"r9 = *(u64 *)(r9 + task_struct::bpf_ctx);"
"*(u32 *)(r9 + bpf_cg_run_ctx::retval) = $src;"
"r9 = *(u64 *)($ctx + bpf_sockopt_kern::tmp_reg);" ,
},
For each test case, up to three programs are created:
- One that uses BPF_LDX_MEM to read the context field.
- One that uses BPF_STX_MEM to write to the context field.
- One that uses BPF_ST_MEM to write to the context field.
The disassembly of each program is compared with the pattern specified
in the test case.
Kernel code for disassembly is reused (as is in the bpftool).
To keep Makefile changes to the minimum, symbolic links to
`kernel/bpf/disasm.c` and `kernel/bpf/disasm.h ` are added.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20230304011247.566040-4-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Check that verifier tracks pointer types for BPF_ST_MEM instructions
and reports error if pointer types do not match for different
execution branches.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20230304011247.566040-3-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Lift verifier restriction to use BPF_ST_MEM instructions to write to
context data structures. This requires the following changes:
- verifier.c:do_check() for BPF_ST updated to:
- no longer forbid writes to registers of type PTR_TO_CTX;
- track dst_reg type in the env->insn_aux_data[...].ptr_type field
(same way it is done for BPF_STX and BPF_LDX instructions).
- verifier.c:convert_ctx_access() and various callbacks invoked by
it are updated to handled BPF_ST instruction alongside BPF_STX.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20230304011247.566040-2-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull more power supply updates from Sebastian Reichel:
- Fix DT binding for Richtek RT9467
- Fix a NULL pointer check in the power-supply core
- Document meaning of absent "present" property
* tag 'for-v6.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
dt-bindings: power: supply: Revise Richtek RT9467 compatible name
ABI: testing: sysfs-class-power: Document absence of "present" property
power: supply: fix null pointer check order in __power_supply_register
|
|
git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
- xfstest generic/208 fix (memory leak)
- minor netfs fix (to address smatch warning)
- a DFS fix for stable
- a reconnect race fix
- two multichannel fixes
- RDMA (smbdirect) fix
- two additional writeback fixes from David
* tag '6.3-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix memory leak in direct I/O
cifs: prevent data race in cifs_reconnect_tcon()
cifs: improve checking of DFS links over STATUS_OBJECT_NAME_INVALID
iov: Fix netfs_extract_user_to_sg()
cifs: Fix cifs_write_back_from_locked_folio()
cifs: reuse cifs_match_ipaddr for comparison of dstaddr too
cifs: match even the scope id for ipv6 addresses
cifs: Fix an uninitialised variable
cifs: Add some missing xas_retry() calls
|
|
The usermodehelper code uses two fake pointers for the two capability
cases: CAP_BSET for reading and writing 'usermodehelper_bset', and
CAP_PI to read and write 'usermodehelper_inheritable'.
This seems to be a completely unnecessary indirection, since we could
instead just use the pointers themselves, and never have to do any "if
this then that" kind of logic.
So just get rid of the fake pointer values, and use the real pointer
values instead.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux
Pull coccinelle updates from Julia Lawall:
"Changes in make coccicheck and improve a semantic patch
This makes a couple of changes in make coccicheck related to shell
commands.
It also updates the api/atomic_as_refcounter semantic patch to include
WARNING in the output message, as done in other cases"
* tag 'cocci-for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccicheck: Use /usr/bin/env
scripts: coccicheck: Avoid warning about spurious escape
coccinelle: api/atomic_as_refcounter: include message type in output
|
|
Pull Rust fix from Miguel Ojeda:
"A single build error fix: there was a change during the merge window
to a C header parsed by the Rust bindings generator, introducing a
type that it does not handle well.
The fix tells the generator to treat the type as opaque (for now)"
* tag 'rust-fixes-6.3-rc1' of https://github.com/Rust-for-Linux/linux:
rust: bindgen: Add `alt_instr` as opaque type
|
|
Pull more SCSI updates from James Bottomley:
"Updates that missed the first pull, mostly because of needing more
soak time.
Driver updates (zfcp, ufs, mpi3mr, plus two ipr bug fixes), an
enclosure services (ses) update (mostly bug fixes) and other minor bug
fixes and changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: zfcp: Trace when request remove fails after qdio send fails
scsi: zfcp: Change the type of all fsf request id fields and variables to u64
scsi: zfcp: Make the type for accessing request hashtable buckets size_t
scsi: ufs: core: Simplify ufshcd_execute_start_stop()
scsi: ufs: core: Rely on the block layer for setting RQF_PM
scsi: core: Extend struct scsi_exec_args
scsi: lpfc: Fix double word in comments
scsi: core: Remove the /proc/scsi/${proc_name} directory earlier
scsi: core: Fix a source code comment
scsi: cxgbi: Remove unneeded version.h include
scsi: qedi: Remove unneeded version.h include
scsi: mpi3mr: Remove unneeded version.h include
scsi: mpi3mr: Fix missing mrioc->evtack_cmds initialization
scsi: mpi3mr: Use number of bits to manage bitmap sizes
scsi: mpi3mr: Remove unnecessary memcpy() to alltgt_info->dmi
scsi: mpi3mr: Fix issues in mpi3mr_get_all_tgt_info()
scsi: mpi3mr: Fix an issue found by KASAN
scsi: mpi3mr: Replace 1-element array with flex-array
scsi: ipr: Work around fortify-string warning
scsi: ipr: Make ipr_probe_ioa_part2() return void
...
|
|
This is passing IS_ERR() instead of PTR_ERR() so instead of an error
code it prints and returns the number 1.
Fixes: 4a55ed6f89f5 ("i2c: Add GXP SoC I2C Controller")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
According to Documentation/i2c/fault-codes.rst, NACK after sending an
address should be -ENXIO.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
There used to be error messages which had to go. Now, it only consists
of 'break's, so it can go.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The ppc64le_allmodconfig sets I2C_PASEMI=y and leaves COMPILE_TEST to
default to y and I2C_APPLE to default to m, running into a known
incompatible configuration that breaks the build [1]. Specifically,
a common dependency (i2c-pasemi-core.o in this case) cannot be used by
both builtin and module consumers.
Disable I2C_APPLE when I2C_PASEMI is a builtin to prevent this.
[1]: https://lore.kernel.org/all/202112061809.XT99aPrf-lkp@intel.com
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These fix two issues in the Intel thermal control drivers.
Specifics:
- Fix an error pointer dereference in the quark_dts Intel thermal
driver (Dan Carpenter)
- Fix the intel_bxt_pmic_thermal driver Kconfig entry to select
REGMAP which is not user-visible instead of depending on it (Randy
Dunlap)"
* tag 'thermal-6.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: BXT_PMIC: select REGMAP instead of depending on it
thermal: intel: quark_dts: fix error pointer dereference
|