| Age | Commit message (Collapse) | Author |
|---|
|
Configure the Macchiatobin 10G PHY LED modes to correct their polarity.
We keep the existing LED behaviours, but switch their polarity to
reflect how they are connected. Tweak the LED modes as well to be:
left: off = no link
solid green = RJ45 link up (not SFP+ cage)
flash green = traffic
right: off = no link
solid green = 10G
solid yellow = 1G
flash green = 100M
flash yellow = 10M
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"The majority of these last fixes are for devicetree files.
These address two important regressions for the Qualcomm SMMU and the
Raspberry Pi 4 USB controller, as well as a larger number of patches
fixing minor mistakes in board specific files for Rockchips, i.MX,
starfive and broadcom.
The non-DT changes are
- A fix for an old boot regression on Renesas shmobile chips
- Another boot time regression for for the Qualcomm PDR SoC driver,
among a few other Qualcomm firmware driver fixes for efivars and
tzmem
- Minor Kconfig fixes for davinci and OMAP1
- Minor code fixes for sparx5 reset controllers, OMAP memory
controller, i.MX SCU, cpufreq and SoC drivers and a Hisilicon SoC
driver
- One more update to the Asahi maintainers, adding Neal Gompa as a
reviewer"
* tag 'soc-fixes-6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: davinci: da850: fix selecting ARCH_DAVINCI_DA8XX
soc: hisilicon: kunpeng_hccs: Fix incorrect string assembly
memory: omap-gpmc: drop no compatible check
reset: mchp: sparx5: Fix for lan966x
ARM: shmobile: smp: Enforce shmobile_smp_* alignment
MAINTAINERS: Add myself (Neal Gompa) as a reviewer for ARM Apple support
MAINTAINERS: Add apple-spi driver & binding files
arm64: dts: rockchip: slow down emmc freq for rock 5 itx
ARM: dts: BCM5301X: Fix switch port labels of ASUS RT-AC3200
ARM: dts: BCM5301X: Fix switch port labels of ASUS RT-AC5300
ARM: dts: bcm2711: Don't mark timer regs unconfigured
ARM: OMAP1: select CONFIG_GENERIC_IRQ_CHIP
arm64: dts: rockchip: Add missing PCIe supplies to RockPro64 board dtsi
arm64: dts: rockchip: Add avdd HDMI supplies to RockPro64 board dtsi
arm64: dts: rockchip: Remove undocumented sdmmc property from lubancat-1
arm64: dts: rockchip: fix pinmux of UART5 for PX30 Ringneck on Haikou
arm64: dts: rockchip: fix pinmux of UART0 for PX30 Ringneck on Haikou
arm64: dts: rockchip: fix u2phy1_host status for NanoPi R4S
arm64: dts: bcm2712: PL011 UARTs are actually r1p5
ARM: dts: bcm2711: PL011 UARTs are actually r1p5
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main one is a horrible macro fix for our TLB flushing code which
resulted in over-invalidation on the MMU notifier path.
Summary:
- Fix population of the vmemmap for regions of memory that are
smaller than a section (128 MiB)
- Fix range-based TLB over-invalidation when invoked via a MMU
notifier"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Fix mmu notifiers for range-based invalidates
arm64: mm: Populate vmemmap at the page level if not section aligned
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm Arm64 Devicetree fixes for v6.14
Revert the change to marking SDM845 SMMU dma-coherent, as this is
reported not to be true.
* tag 'qcom-arm64-fixes-for-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
Revert "arm64: dts: qcom: sdm845: Affirm IDR0.CCTW on apps_smmu"
Link: https://lore.kernel.org/r/20250310191409.1208520-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
A number of emmc fixes (removing CQE from Theobroma boards and slower
freq on Rock-5-ITX) as well as some pinmux fixes and missing supplies.
* tag 'v6.14-rockchip-dtsfixes2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: slow down emmc freq for rock 5 itx
arm64: dts: rockchip: Add missing PCIe supplies to RockPro64 board dtsi
arm64: dts: rockchip: Add avdd HDMI supplies to RockPro64 board dtsi
arm64: dts: rockchip: Remove undocumented sdmmc property from lubancat-1
arm64: dts: rockchip: fix pinmux of UART5 for PX30 Ringneck on Haikou
arm64: dts: rockchip: fix pinmux of UART0 for PX30 Ringneck on Haikou
arm64: dts: rockchip: fix u2phy1_host status for NanoPi R4S
arm64: dts: rockchip: remove supports-cqe from rk3588 tiger
arm64: dts: rockchip: remove supports-cqe from rk3588 jaguar
Link: https://lore.kernel.org/r/1990830.tdWV9SEqCh@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Update the __flush_tlb_range_op macro not to modify its parameters as
these are unexepcted semantics. In practice, this fixes the call to
mmu_notifier_arch_invalidate_secondary_tlbs() in
__flush_tlb_range_nosync() to use the correct range instead of an empty
range with start=end. The empty range was (un)lucky as it results in
taking the invalidate-all path that doesn't cause correctness issues,
but can certainly result in suboptimal perf.
This has been broken since commit 6bbd42e2df8f ("mmu_notifiers: call
invalidate_range() when invalidating TLBs") when the call to the
notifiers was added to __flush_tlb_range(). It predates the addition of
the __flush_tlb_range_op() macro from commit 360839027a6e ("arm64: tlb:
Refactor the core flush algorithm of __flush_tlb_range") that made the
bug hard to spot.
Fixes: 6bbd42e2df8f ("mmu_notifiers: call invalidate_range() when invalidating TLBs")
Signed-off-by: Piotr Jaroszynski <pjaroszynski@nvidia.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Raghavendra Rao Ananta <rananta@google.com>
Cc: SeongJae Park <sj@kernel.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Nicolin Chen <nicolinc@nvidia.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: iommu@lists.linux.dev
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Link: https://lore.kernel.org/r/20250304085127.2238030-1-pjaroszynski@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
On the arm64 platform with 4K base page config, SECTION_SIZE_BITS is set
to 27, making one section 128M. The related page struct which vmemmap
points to is 2M then.
Commit c1cc1552616d ("arm64: MMU initialisation") optimizes the
vmemmap to populate at the PMD section level which was suitable
initially since hot plug granule is always one section(128M). However,
commit ba72b4c8cf60 ("mm/sparsemem: support sub-section hotplug")
introduced a 2M(SUBSECTION_SIZE) hot plug granule, which disrupted the
existing arm64 assumptions.
The first problem is that if start or end is not aligned to a section
boundary, such as when a subsection is hot added, populating the entire
section is wasteful.
The next problem is if we hotplug something that spans part of 128 MiB
section (subsections, let's call it memblock1), and then hotplug something
that spans another part of a 128 MiB section(subsections, let's call it
memblock2), and subsequently unplug memblock1, vmemmap_free() will clear
the entire PMD entry which also supports memblock2 even though memblock2
is still active.
Assuming hotplug/unplug sizes are guaranteed to be symmetric. Do the
fix similar to x86-64: populate to pages levels if start/end is not aligned
with section boundary.
Cc: stable@vger.kernel.org # v5.4+
Fixes: ba72b4c8cf60 ("mm/sparsemem: support sub-section hotplug")
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Zhenhua Huang <quic_zhenhuah@quicinc.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20250304072700.3405036-1-quic_zhenhuah@quicinc.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Pull KVM fixes from Paolo Bonzini:
"arm64:
- Fix a couple of bugs affecting pKVM's PSCI relay implementation
when running in the hVHE mode, resulting in the host being entered
with the MMU in an unknown state, and EL2 being in the wrong mode
x86:
- Set RFLAGS.IF in C code on SVM to get VMRUN out of the STI shadow
- Ensure DEBUGCTL is context switched on AMD to avoid running the
guest with the host's value, which can lead to unexpected bus lock
#DBs
- Suppress DEBUGCTL.BTF on AMD (to match Intel), as KVM doesn't
properly emulate BTF. KVM's lack of context switching has meant BTF
has always been broken to some extent
- Always save DR masks for SNP vCPUs if DebugSwap is *supported*, as
the guest can enable DebugSwap without KVM's knowledge
- Fix a bug in mmu_stress_tests where a vCPU could finish the "writes
to RO memory" phase without actually generating a write-protection
fault
- Fix a printf() goof in the SEV smoke test that causes build
failures with -Werror
- Explicitly zero EAX and EBX in CPUID.0x8000_0022 output when
PERFMON_V2 isn't supported by KVM"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Explicitly zero EAX and EBX when PERFMON_V2 isn't supported by KVM
KVM: selftests: Fix printf() format goof in SEV smoke test
KVM: selftests: Ensure all vCPUs hit -EFAULT during initial RO stage
KVM: SVM: Don't rely on DebugSwap to restore host DR0..DR3
KVM: SVM: Save host DR masks on CPUs with DebugSwap
KVM: arm64: Initialize SCTLR_EL1 in __kvm_hyp_init_cpu()
KVM: arm64: Initialize HCR_EL2.E2H early
KVM: x86: Snapshot the host's DEBUGCTL after disabling IRQs
KVM: SVM: Manually context switch DEBUGCTL if LBR virtualization is disabled
KVM: x86: Snapshot the host's DEBUGCTL in common x86
KVM: SVM: Suppress DEBUGCTL.BTF on AMD
KVM: SVM: Drop DEBUGCTL[5:2] from guest's effective value
KVM: selftests: Assert that STI blocking isn't set after event injection
KVM: SVM: Set RFLAGS.IF=1 in C code, to get VMRUN out of the STI shadow
|
|
The current max-frequency 200000000 of emmc is not stable. When doing
heavy write there will be I/O Error. After setting max-frequency to
150000000 the emmc is stable under write.
Also remove property mmc-hs200-1_8v because we are already running at
HS400 mode.
Tested with fio command:
fio -filename=./test_randread -direct=1 -iodepth 1 -thread \
-rw=randwrite -ioengine=psync -bs=16k -size=1G -numjobs=10 \
-runtime=600 -group_reporting -name=mytest
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Link: https://lore.kernel.org/r/20250228143341.70244-1-liujianfeng1994@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.14:
- A tqma8mpql board fix from Alexander Stein to correct vqmmc-supply for
usdhc3
- A change from Joe Hattori to fix OF node leak in imx-scu driver probe
- A soc-imx8m driver fix from Peng Fan unregister cpufreq and soc device
in cleanup path
- A couple of changes from Stefan Eichenberger to fix iMX6 Apalis
poweroff and iMX8M verdin-dahlia sound-card descriptions
* tag 'imx-fixes-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: freescale: imx8mm-verdin-dahlia: add Microphone Jack to sound card
arm64: dts: freescale: imx8mp-verdin-dahlia: add Microphone Jack to sound card
soc: imx8m: Unregister cpufreq and soc dev in cleanup path
ARM: dts: imx6qdl-apalis: Fix poweroff on Apalis iMX6
arm64: dts: freescale: tqma8mpql: Fix vqmmc-supply
firmware: imx-scu: fix OF node leak in .probe()
Link: https://lore.kernel.org/r/Z8A+rihFV4K3l8QR@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 6.14, please pull the following:
- Phil fixes the Raspberry Pi 5 PL011 UART primecell ID to indicate it
is r1p5 and thus has a 32-byte FIFO
* tag 'arm-soc/for-6.14/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: bcm2712: PL011 UARTs are actually r1p5
Link: https://lore.kernel.org/r/20250225194041.1063762-2-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add missing "vpcie0v9-supply" and "vpcie1v8-supply" properties to the "pcie0"
node in the Pine64 RockPro64 board dtsi file. This eliminates the following
warnings from the kernel log:
rockchip-pcie f8000000.pcie: supply vpcie1v8 not found, using dummy regulator
rockchip-pcie f8000000.pcie: supply vpcie0v9 not found, using dummy regulator
These additions improve the accuracy of hardware description of the RockPro64
and, in theory, they should result in no functional changes to the way board
works after the changes, because the "vcca_0v9" and "vcca_1v8" regulators are
always enabled. [1][2] However, extended reliability testing, performed by
Chris, [3] has proven that the age-old issues with some PCI Express cards,
when used with a Pine64 RockPro64, are also resolved.
Those issues were already mentioned in the commit 43853e843aa6 (arm64: dts:
rockchip: Remove unsupported node from the Pinebook Pro dts, 2024-04-01),
together with a brief description of the out-of-tree enumeration delay patch
that reportedly resolves those issues. In a nutshell, booting a RockPro64
with some PCI Express cards attached to it caused a kernel oops. [4]
Symptomatically enough, to the commit author's best knowledge, only the Pine64
RockPro64, out of all RK3399-based boards and devices supported upstream, has
been reported to suffer from those PCI Express issues, and only the RockPro64
had some of the PCI Express supplies missing in its DT. Thus, perhaps some
weird timing issues exist that caused the "vcca_1v8" always-on regulator,
which is part of the RK808 PMIC, to actually not be enabled before the PCI
Express is initialized and enumerated on the RockPro64, causing oopses with
some PCIe cards, and the aforementioned enumeration delay patch [4] probably
acted as just a workaround for the underlying timing issue.
Admittedly, the Pine64 RockPro64 is a bit specific board by having a standard
PCI Express slot, allowing use of various standard cards, but pretty much
standard PCI Express cards have been attached to other RK3399 boards as well,
and the commit author is unaware ot such issues reported for them.
It's quite hard to be sure that the PCI Express issues are fully resolved by
these additions to the DT, without some really extensive and time-consuming
testing. However, these additions to the DT can result in good things and
improvements anyway, making them perfectly safe from the standpoint of being
unable to do any harm or cause some unforeseen regressions.
These changes apply to the both supported hardware revisions of the Pine64
RockPro64, i.e. to the production-run revisions 2.0 and 2.1. [1][2]
[1] https://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
[2] https://files.pine64.org/doc/rockpro64/rockpro64_v20-SCH.pdf
[3] https://z9.de/hedgedoc/s/nF4d5G7rg#reboot-tests-for-PCIe-improvements
[4] https://lore.kernel.org/lkml/20230509153912.515218-1-vincenzopalazzodev@gmail.com/T/#u
Fixes: bba821f5479e ("arm64: dts: rockchip: add PCIe nodes on rk3399-rockpro64")
Cc: stable@vger.kernel.org
Cc: Vincenzo Palazzo <vincenzopalazzodev@gmail.com>
Cc: Peter Geis <pgwipeout@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Reported-by: Diederik de Haas <didi.debian@cknow.org>
Tested-by: Chris Vogel <chris@z9.de>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/b39cfd7490d8194f053bf3971f13a43472d1769e.1740941097.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add missing "avdd-0v9-supply" and "avdd-1v8-supply" properties to the "hdmi"
node in the Pine64 RockPro64 board dtsi file. To achieve this, also add the
associated "vcca_0v9" regulator that produces the 0.9 V supply, [1][2] which
hasn't been defined previously in the board dtsi file.
This also eliminates the following warnings from the kernel log:
dwhdmi-rockchip ff940000.hdmi: supply avdd-0v9 not found, using dummy regulator
dwhdmi-rockchip ff940000.hdmi: supply avdd-1v8 not found, using dummy regulator
There are no functional changes to the way board works with these additions,
because the "vcc1v8_dvp" and "vcca_0v9" regulators are always enabled, [1][2]
but these additions improve the accuracy of hardware description.
These changes apply to the both supported hardware revisions of the Pine64
RockPro64, i.e. to the production-run revisions 2.0 and 2.1. [1][2]
[1] https://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
[2] https://files.pine64.org/doc/rockpro64/rockpro64_v20-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Cc: stable@vger.kernel.org
Suggested-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/df3d7e8fe74ed5e727e085b18c395260537bb5ac.1740941097.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When KVM is in protected mode, host calls to PSCI are proxied via EL2,
and cold entries from CPU_ON, CPU_SUSPEND, and SYSTEM_SUSPEND bounce
through __kvm_hyp_init_cpu() at EL2 before entering the host kernel's
entry point at EL1. While __kvm_hyp_init_cpu() initializes SPSR_EL2 for
the exception return to EL1, it does not initialize SCTLR_EL1.
Due to this, it's possible to enter EL1 with SCTLR_EL1 in an UNKNOWN
state. In practice this has been seen to result in kernel crashes after
CPU_ON as a result of SCTLR_EL1.M being 1 in violation of the initial
core configuration specified by PSCI.
Fix this by initializing SCTLR_EL1 for cold entry to the host kernel.
As it's necessary to write to SCTLR_EL12 in VHE mode, this
initialization is moved into __kvm_host_psci_cpu_entry() where we can
use write_sysreg_el1().
The remnants of the '__init_el2_nvhe_prepare_eret' macro are folded into
its only caller, as this is clearer than having the macro.
Fixes: cdf367192766ad11 ("KVM: arm64: Intercept host's CPU_ON SMCs")
Reported-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Ahmed Genidi <ahmed.genidi@arm.com>
[ Mark: clarify commit message, handle E2H, move to C, remove macro ]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ahmed Genidi <ahmed.genidi@arm.com>
Cc: Ben Horgan <ben.horgan@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Leo Yan <leo.yan@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Link: https://lore.kernel.org/r/20250227180526.1204723-3-mark.rutland@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
On CPUs without FEAT_E2H0, HCR_EL2.E2H is RES1, but may reset to an
UNKNOWN value out of reset and consequently may not read as 1 unless it
has been explicitly initialized.
We handled this for the head.S boot code in commits:
3944382fa6f22b54 ("arm64: Treat HCR_EL2.E2H as RES1 when ID_AA64MMFR4_EL1.E2H0 is negative")
b3320142f3db9b3f ("arm64: Fix early handling of FEAT_E2H0 not being implemented")
Unfortunately, we forgot to apply a similar fix to the KVM PSCI entry
points used when relaying CPU_ON, CPU_SUSPEND, and SYSTEM SUSPEND. When
KVM is entered via these entry points, the value of HCR_EL2.E2H may be
consumed before it has been initialized (e.g. by the 'init_el2_state'
macro).
Initialize HCR_EL2.E2H early in these paths such that it can be consumed
reliably. The existing code in head.S is factored out into a new
'init_el2_hcr' macro, and this is used in the __kvm_hyp_init_cpu()
function common to all the relevant PSCI entry points.
For clarity, I've tweaked the assembly used to check whether
ID_AA64MMFR4_EL1.E2H0 is negative. The bitfield is extracted as a signed
value, and this is checked with a signed-greater-or-equal (GE) comparison.
As the hyp code will reconfigure HCR_EL2 later in ___kvm_hyp_init(), all
bits other than E2H are initialized to zero in __kvm_hyp_init_cpu().
Fixes: 3944382fa6f22b54 ("arm64: Treat HCR_EL2.E2H as RES1 when ID_AA64MMFR4_EL1.E2H0 is negative")
Fixes: b3320142f3db9b3f ("arm64: Fix early handling of FEAT_E2H0 not being implemented")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ahmed Genidi <ahmed.genidi@arm.com>
Cc: Ben Horgan <ben.horgan@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Leo Yan <leo.yan@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20250227180526.1204723-2-mark.rutland@arm.com
[maz: fixed LT->GE thinko]
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Ryan's been hard at work finding and fixing mm bugs in the arm64 code,
so here's a small crop of fixes for -rc5.
The main changes are to fix our zapping of non-present PTEs for
hugetlb entries created using the contiguous bit in the page-table
rather than a block entry at the level above. Prior to these fixes, we
were pulling the contiguous bit back out of the PTE in order to
determine the size of the hugetlb page but this is clearly bogus if
the thing isn't present and consequently both the clearing of the
PTE(s) and the TLB invalidation were unreliable.
Although the problem was found by code inspection, we really don't
want this sitting around waiting to trigger and the changes are CC'd
to stable accordingly.
Note that the diffstat looks a lot worse than it really is;
huge_ptep_get_and_clear() now takes a size argument from the core code
and so all the arch implementations of that have been updated in a
pretty mechanical fashion.
- Fix a sporadic boot failure due to incorrect randomization of the
linear map on systems that support it
- Fix the zapping (both clearing the entries *and* invalidating the
TLB) of hugetlb PTEs constructed using the contiguous bit"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: hugetlb: Fix flush_hugetlb_tlb_range() invalidation level
arm64: hugetlb: Fix huge_ptep_get_and_clear() for non-present ptes
mm: hugetlb: Add huge page size param to huge_ptep_get_and_clear()
arm64/mm: Fix Boot panic on Ampere Altra
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix TCR_EL2 configuration to not use the ASID in TTBR1_EL2 and not
mess-up T1SZ/PS by using the HCR_EL2.E2H==0 layout.
- Bring back the VMID allocation to the vcpu_load phase, ensuring
that we only setup VTTBR_EL2 once on VHE. This cures an ugly race
that would lead to running with an unallocated VMID.
RISC-V:
- Fix hart status check in SBI HSM extension
- Fix hart suspend_type usage in SBI HSM extension
- Fix error returned by SBI IPI and TIME extensions for unsupported
function IDs
- Fix suspend_type usage in SBI SUSP extension
- Remove unnecessary vcpu kick after injecting interrupt via IMSIC
guest file
x86:
- Fix an nVMX bug where KVM fails to detect that, after nested
VM-Exit, L1 has a pending IRQ (or NMI).
- To avoid freeing the PIC while vCPUs are still around, which would
cause a NULL pointer access with the previous patch, destroy vCPUs
before any VM-level destruction.
- Handle failures to create vhost_tasks"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: retry nx_huge_page_recovery_thread creation
vhost: return task creation error instead of NULL
KVM: nVMX: Process events on nested VM-Exit if injectable IRQ or NMI is pending
KVM: x86: Free vCPUs before freeing VM state
riscv: KVM: Remove unnecessary vcpu kick
KVM: arm64: Ensure a VMID is allocated before programming VTTBR_EL2
KVM: arm64: Fix tcr_el2 initialisation in hVHE mode
riscv: KVM: Fix SBI sleep_type use
riscv: KVM: Fix SBI TIME error generation
riscv: KVM: Fix SBI IPI error generation
riscv: KVM: Fix hart suspend_type use
riscv: KVM: Fix hart suspend status check
|
|
Property "supports-sd" isn't documented anywhere and is unnecessary for
mainline driver to function. It seems a property used by downstream
kernel was brought into mainline.
This should be reported by dtbs_check, but mmc-controller-common.yaml
defaults additionalProperties to true thus allows it. Remove the
property to clean the devicetree up and avoid possible confusion.
Fixes: 8d94da58de53 ("arm64: dts: rockchip: Add EmbedFire LubanCat 1")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250228163117.47318-2-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
commit c910f2b65518 ("arm64/mm: Update tlb invalidation routines for
FEAT_LPA2") changed the "invalidation level unknown" hint from 0 to
TLBI_TTL_UNKNOWN (INT_MAX). But the fallback "unknown level" path in
flush_hugetlb_tlb_range() was not updated. So as it stands, when trying
to invalidate CONT_PMD_SIZE or CONT_PTE_SIZE hugetlb mappings, we will
spuriously try to invalidate at level 0 on LPA2-enabled systems.
Fix this so that the fallback passes TLBI_TTL_UNKNOWN, and while we are
at it, explicitly use the correct stride and level for CONT_PMD_SIZE and
CONT_PTE_SIZE, which should provide a minor optimization.
Cc: stable@vger.kernel.org
Fixes: c910f2b65518 ("arm64/mm: Update tlb invalidation routines for FEAT_LPA2")
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250226120656.2400136-4-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
arm64 supports multiple huge_pte sizes. Some of the sizes are covered by
a single pte entry at a particular level (PMD_SIZE, PUD_SIZE), and some
are covered by multiple ptes at a particular level (CONT_PTE_SIZE,
CONT_PMD_SIZE). So the function has to figure out the size from the
huge_pte pointer. This was previously done by walking the pgtable to
determine the level and by using the PTE_CONT bit to determine the
number of ptes at the level.
But the PTE_CONT bit is only valid when the pte is present. For
non-present pte values (e.g. markers, migration entries), the previous
implementation was therefore erroneously determining the size. There is
at least one known caller in core-mm, move_huge_pte(), which may call
huge_ptep_get_and_clear() for a non-present pte. So we must be robust to
this case. Additionally the "regular" ptep_get_and_clear() is robust to
being called for non-present ptes so it makes sense to follow the
behavior.
Fix this by using the new sz parameter which is now provided to the
function. Additionally when clearing each pte in a contig range, don't
gather the access and dirty bits if the pte is not present.
An alternative approach that would not require API changes would be to
store the PTE_CONT bit in a spare bit in the swap entry pte for the
non-present case. But it felt cleaner to follow other APIs' lead and
just pass in the size.
As an aside, PTE_CONT is bit 52, which corresponds to bit 40 in the swap
entry offset field (layout of non-present pte). Since hugetlb is never
swapped to disk, this field will only be populated for markers, which
always set this bit to 0 and hwpoison swap entries, which set the offset
field to a PFN; So it would only ever be 1 for a 52-bit PVA system where
memory in that high half was poisoned (I think!). So in practice, this
bit would almost always be zero for non-present ptes and we would only
clear the first entry if it was actually a contiguous block. That's
probably a less severe symptom than if it was always interpreted as 1
and cleared out potentially-present neighboring PTEs.
Cc: stable@vger.kernel.org
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250226120656.2400136-3-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In order to fix a bug, arm64 needs to be told the size of the huge page
for which the huge_pte is being cleared in huge_ptep_get_and_clear().
Provide for this by adding an `unsigned long sz` parameter to the
function. This follows the same pattern as huge_pte_clear() and
set_huge_pte_at().
This commit makes the required interface modifications to the core mm as
well as all arches that implement this function (arm64, loongarch, mips,
parisc, powerpc, riscv, s390, sparc). The actual arm64 bug will be fixed
in a separate commit.
Cc: stable@vger.kernel.org
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com> # riscv
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> # s390
Link: https://lore.kernel.org/r/20250226120656.2400136-2-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
UART5 uses GPIO0_B5 as UART RTS but muxed in its GPIO function,
therefore UART5 must request this pin to be muxed in that function, so
let's do that.
Fixes: 5963d97aa780 ("arm64: dts: rockchip: add rs485 support on uart5 of px30-ringneck-haikou")
Cc: stable@vger.kernel.org
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250225-ringneck-dtbos-v3-2-853a9a6dd597@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
UART0 pinmux by default configures GPIO0_B5 in its UART RTS function for
UART0. However, by default on Haikou, it is used as GPIO as UART RTS for
UART5.
Therefore, let's update UART0 pinmux to not configure the pin in that
mode, a later commit will make UART5 request the GPIO pinmux.
Fixes: c484cf93f61b ("arm64: dts: rockchip: add PX30-µQ7 (Ringneck) SoM with Haikou baseboard")
Cc: stable@vger.kernel.org
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250225-ringneck-dtbos-v3-1-853a9a6dd597@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The u2phy1_host should always have the same status as usb_host1_ehci
and usb_host1_ohci, otherwise the EHCI and OHCI drivers may be
initialized for a disabled usb port.
Per the NanoPi R4S schematic, the phy-supply for u2phy1_host is set to
the vdd_5v regulator.
Fixes: db792e9adbf8 ("rockchip: rk3399: Add support for FriendlyARM NanoPi R4S")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250225170420.3898-1-justin@tidylabs.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When the range of present physical memory is sufficiently small enough
and the reserved address space for the linear map is sufficiently large
enough, The linear map base address is randomized in
arm64_memblock_init().
Prior to commit 62cffa496aac ("arm64/mm: Override PARange for !LPA2 and
use it consistently"), we decided if the sizes were suitable with the
help of the raw mmfr0.parange. But the commit changed this to use the
sanitized version instead. But the function runs before the register has
been sanitized so this returns 0, interpreted as a parange of 32 bits.
Some fun wrapping occurs and the logic concludes that there is enough
room to randomize the linear map base address, when really there isn't.
So the top of the linear map ends up outside the reserved address space.
Since the PA range cannot be overridden in the first place, restore the
mmfr0 reading logic to its state prior to 62cffa496aac, where the raw
register value is used.
Reported-by: Luiz Capitulino <luizcap@redhat.com>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Closes: https://lore.kernel.org/all/a3d9acbe-07c2-43b6-9ba9-a7585f770e83@redhat.com/
Fixes: 62cffa496aac ("arm64/mm: Override PARange for !LPA2 and use it consistently")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250225114638.2038006-1-ryan.roberts@arm.com
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The ARM PL011 UART instances in BCM2712 are r1p5 spec, which means they
have 32-entry FIFOs. The correct periphid value for this is 0x00341011.
Thanks to N Buchwitz for pointing this out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250223125614.3592-3-wahrenst@gmx.net
Fixes: faa3381267d0 ("arm64: dts: broadcom: Add minimal support for Raspberry Pi 5")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
There are reports that the pagetable walker cache coherency is not a
given across the spectrum of SDM845/850 devices, leading to lock-ups
and resets. It works fine on some devices (like the Dragonboard 845c,
but not so much on the Lenovo Yoga C630).
This unfortunately looks like a fluke in firmware development, where
likely somewhere in the vast hypervisor stack, a change to accommodate
for this was only introduced after the initial software release (which
often serves as a baseline for products).
Revert the change to avoid additional guesswork around crashes.
This reverts commit 6b31a9744b8726c69bb0af290f8475a368a4b805.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Closes: https://lore.kernel.org/linux-arm-msm/20250215-yoga-dma-coherent-v1-1-2419ee184a81@linaro.org/
Fixes: 6b31a9744b87 ("arm64: dts: qcom: sdm845: Affirm IDR0.CCTW on apps_smmu")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250225-topic-845_smmu_not_coherent-v1-1-98ca9d17471c@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The simple-audio-card's microphone widget currently connects to the
headphone jack. Routing the microphone input to the microphone jack
allows for independent operation of the microphone and headphones.
This resolves the following boot-time kernel log message, which
indicated a conflict when the microphone and headphone functions were
not separated:
debugfs: File 'Headphone Jack' in directory 'dapm' already present!
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The simple-audio-card's microphone widget currently connects to the
headphone jack. Routing the microphone input to the microphone jack
allows for independent operation of the microphone and headphones.
This resolves the following boot-time kernel log message, which
indicated a conflict when the microphone and headphone functions were
not separated:
debugfs: File 'Headphone Jack' in directory 'dapm' already present!
Fixes: 874958916844 ("arm64: dts: freescale: verdin-imx8mp: dahlia: add sound card")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"Two people stepped up as platform co-maintainers: Andrew Jeffery for
ASpeed and Janne Grunau for Apple.
The rockchip platform gets 9 small fixes for devicetree files,
addressing both compile-time warnings and board specific bugs.
One bugfix for the optee firmware driver addresses a reboot-time hang.
Two drivers need improved Kconfig dependencies to allow wider compile-
testing while hiding the drivers on platforms that can't use them.
ARM SCMI and loongson-guts drivers get minor bugfixes"
* tag 'soc-fixes-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: loongson: loongson2_guts: Add check for devm_kstrdup()
tee: optee: Fix supplicant wait loop
platform: cznic: CZNIC_PLATFORMS should depend on ARCH_MVEBU
firmware: imx: IMX_SCMI_MISC_DRV should depend on ARCH_MXC
MAINTAINERS: arm: apple: Add Janne as maintainer
MAINTAINERS: Mark Andrew as M: for ASPEED MACHINE SUPPORT
firmware: arm_scmi: imx: Correct tx size of scmi_imx_misc_ctrl_set
arm64: dts: rockchip: adjust SMMU interrupt type on rk3588
arm64: dts: rockchip: disable IOMMU when running rk3588 in PCIe endpoint mode
dt-bindings: rockchip: pmu: Ensure all properties are defined
arm64: defconfig: Enable TISCI Interrupt Router and Aggregator
arm64: dts: rockchip: Fix lcdpwr_en pin for Cool Pi GenBook
arm64: dts: rockchip: fix fixed-regulator renames on rk3399-gru devices
arm64: dts: rockchip: Disable DMA for uart5 on px30-ringneck
arm64: dts: rockchip: Move uart5 pin configuration to px30 ringneck SoM
arm64: dts: rockchip: change eth phy mode to rgmii-id for orangepi r1 plus lts
arm64: dts: rockchip: Fix broken tsadc pinctrl names for rk3588
|
|
Vladimir reports that a race condition to attach a VMID to a stage-2 MMU
sometimes results in a vCPU entering the guest with a VMID of 0:
| CPU1 | CPU2
| |
| | kvm_arch_vcpu_ioctl_run
| | vcpu_load <= load VTTBR_EL2
| | kvm_vmid->id = 0
| |
| kvm_arch_vcpu_ioctl_run |
| vcpu_load <= load VTTBR_EL2 |
| with kvm_vmid->id = 0|
| kvm_arm_vmid_update <= allocates fresh |
| kvm_vmid->id and |
| reload VTTBR_EL2 |
| |
| | kvm_arm_vmid_update <= observes that kvm_vmid->id
| | already allocated,
| | skips reload VTTBR_EL2
Oh yeah, it's as bad as it looks. Remember that VHE loads the stage-2
MMU eagerly but a VMID only gets attached to the MMU later on in the
KVM_RUN loop.
Even in the "best case" where VTTBR_EL2 correctly gets reprogrammed
before entering the EL1&0 regime, there is a period of time where
hardware is configured with VMID 0. That's completely insane. So, rather
than decorating the 'late' binding with another hack, just allocate the
damn thing up front.
Attaching a VMID from vcpu_load() is still rollover safe since
(surprise!) it'll always get called after a vCPU was preempted.
Excuse me while I go find a brown paper bag.
Cc: stable@vger.kernel.org
Fixes: 934bf871f011 ("KVM: arm64: Load the stage-2 MMU context in kvm_vcpu_load_vhe()")
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250219220737.130842-1-oliver.upton@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
The sdhci controller supports cqe it seems and necessary code also is in
place - in theory.
At this point Jaguar and Tiger are the only boards enabling cqe support
on the rk3588 and we are seeing reliability issues under load.
This can be caused by either a controller-, hw- or driver-issue and
definitly needs more investigation to work properly it seems.
So disable cqe support on Tiger for now.
Fixes: 6173ef24b35b ("arm64: dts: rockchip: add RK3588-Q7 (Tiger) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250219093303.2320517-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The sdhci controller supports cqe it seems and necessary code also is in
place - in theory.
At this point Jaguar and Tiger are the only boards enabling cqe support
on the rk3588 and we are seeing reliability issues under load.
This can be caused by either a controller-, hw- or driver-issue and
definitly needs more investigation to work properly it seems.
So disable cqe support on Jaguar for now.
Fixes: d1b8b36a2cc5 ("arm64: dts: rockchip: add Theobroma Jaguar SBC")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250219093303.2320517-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When not running in VHE mode, cpu_prepare_hyp_mode() computes the value
of TCR_EL2 using the host's TCR_EL1 settings as a starting point. For
nVHE, this amounts to masking out everything apart from the TG0, SH0,
ORGN0, IRGN0 and T0SZ fields before setting the RES1 bits, shifting the
IPS field down to the PS field and setting DS if LPA2 is enabled.
Unfortunately, for hVHE, things go slightly wonky: EPD1 is correctly set
to disable walks via TTBR1_EL2 but then the T1SZ and IPS fields are
corrupted when we mistakenly attempt to initialise the PS and DS fields
in their E2H=0 positions. Furthermore, many fields are retained from
TCR_EL1 which should not be propagated to TCR_EL2. Notably, this means
we can end up with A1 set despite not initialising TTBR1_EL2 at all.
This has been shown to cause unexpected translation faults at EL2 with
pKVM due to TLB invalidation not taking effect when running with a
non-zero ASID.
Fix the TCR_EL2 initialisation code to set PS and DS only when E2H=0,
masking out HD, HA and A1 when E2H=1.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Fixes: ad744e8cb346 ("arm64: Allow arm64_sw.hvhe on command line")
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20250214133724.13179-1-will@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
eMMC is supplied by BUCK5 rail. Use the actual regulator instead of
a virtual fixed regulator.
Fixes: 418d1d840e421 ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Large set of fixes for vector handling, especially in the
interactions between host and guest state.
This fixes a number of bugs affecting actual deployments, and
greatly simplifies the FP/SIMD/SVE handling. Thanks to Mark Rutland
for dealing with this thankless task.
- Fix an ugly race between vcpu and vgic creation/init, resulting in
unexpected behaviours
- Fix use of kernel VAs at EL2 when emulating timers with nVHE
- Small set of pKVM improvements and cleanups
x86:
- Fix broken SNP support with KVM module built-in, ensuring the PSP
module is initialized before KVM even when the module
infrastructure cannot be used to order initcalls
- Reject Hyper-V SEND_IPI hypercalls if the local APIC isn't being
emulated by KVM to fix a NULL pointer dereference
- Enter guest mode (L2) from KVM's perspective before initializing
the vCPU's nested NPT MMU so that the MMU is properly tagged for
L2, not L1
- Load the guest's DR6 outside of the innermost .vcpu_run() loop, as
the guest's value may be stale if a VM-Exit is handled in the
fastpath"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
x86/sev: Fix broken SNP support with KVM module built-in
KVM: SVM: Ensure PSP module is initialized if KVM module is built-in
crypto: ccp: Add external API interface for PSP module initialization
KVM: arm64: vgic: Hoist SGI/PPI alloc from vgic_init() to kvm_create_vgic()
KVM: arm64: timer: Drop warning on failed interrupt signalling
KVM: arm64: Fix alignment of kvm_hyp_memcache allocations
KVM: arm64: Convert timer offset VA when accessed in HYP code
KVM: arm64: Simplify warning in kvm_arch_vcpu_load_fp()
KVM: arm64: Eagerly switch ZCR_EL{1,2}
KVM: arm64: Mark some header functions as inline
KVM: arm64: Refactor exit handlers
KVM: arm64: Refactor CPTR trap deactivation
KVM: arm64: Remove VHE host restore of CPACR_EL1.SMEN
KVM: arm64: Remove VHE host restore of CPACR_EL1.ZEN
KVM: arm64: Remove host FPSIMD saving for non-protected KVM
KVM: arm64: Unconditionally save+flush host FPSIMD/SVE/SME state
KVM: x86: Load DR6 with guest value only before entering .vcpu_run() loop
KVM: nSVM: Enter guest mode before initializing nested NPT MMU
KVM: selftests: Add CPUID tests for Hyper-V features that need in-kernel APIC
KVM: selftests: Manage CPUID array in Hyper-V CPUID test's core helper
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.14, take #2
- Large set of fixes for vector handling, specially in the interactions
between host and guest state. This fixes a number of bugs affecting
actual deployments, and greatly simplifies the FP/SIMD/SVE handling.
Thanks to Mark Rutland for dealing with this thankless task.
- Fix an ugly race between vcpu and vgic creation/init, resulting in
unexpected behaviours.
- Fix use of kernel VAs at EL2 when emulating timers with nVHE.
- Small set of pKVM improvements and cleanups.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix kexec and hibernation when using 5-level page-table configuration
- Remove references to non-existent SF8MM4 and SF8MM8 ID register
fields, hooking up hwcaps for the FPRCVT, F8MM4 and F8MM8 fields
instead
- Drop unused .ARM.attributes ELF sections
- Fix array indexing when probing CPU cache topology from firmware
- Fix potential use-after-free in AMU initialisation code
- Work around broken GTDT entries by tolerating excessively large timer
arrays
- Force use of Rust's "softfloat" target to avoid a threatening warning
about the NEON target feature
- Typo fix in GCS documentation and removal of duplicate Kconfig select
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: rust: clean Rust 1.85.0 warning using softfloat target
arm64: Add missing registrations of hwcaps
ACPI: GTDT: Relax sanity checking on Platform Timers array count
arm64: amu: Delay allocating cpumask for AMU FIE support
arm64: cacheinfo: Avoid out-of-bounds write to cacheinfo array
arm64: Handle .ARM.attributes section in linker scripts
arm64/hwcap: Remove stray references to SF8MMx
arm64/gcs: Fix documentation for HWCAP
arm64: Kconfig: Remove selecting replaced HAVE_FUNCTION_GRAPH_RETVAL
arm64: Fix 5-level paging support in kexec/hibernate trampoline
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into HEAD
TI K3 defconfig fixes for v6.14
- Enable TISCI Interrupt Router, Interrupt Aggregator and related drivers.
* tag 'ti-k3-config-fixes-for-v6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
arm64: defconfig: Enable TISCI Interrupt Router and Aggregator
Link: https://lore.kernel.org/r/20250212112857.pm6ptaqbx545qnv7@eternity
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into HEAD
Fixes for the IOMMU used together with the PCIe controllers on rk3588,
some board-level fixes for wrong pins, pinctrl and regulators, and
disabling DMA on a board where the DMA+uart causes the dma controller to
hang, as well as improved network stability for the OrangePi R1.
* tag 'v6.14-rockchip-dtsfixes1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: adjust SMMU interrupt type on rk3588
arm64: dts: rockchip: disable IOMMU when running rk3588 in PCIe endpoint mode
dt-bindings: rockchip: pmu: Ensure all properties are defined
arm64: dts: rockchip: Fix lcdpwr_en pin for Cool Pi GenBook
arm64: dts: rockchip: fix fixed-regulator renames on rk3399-gru devices
arm64: dts: rockchip: Disable DMA for uart5 on px30-ringneck
arm64: dts: rockchip: Move uart5 pin configuration to px30 ringneck SoM
arm64: dts: rockchip: change eth phy mode to rgmii-id for orangepi r1 plus lts
arm64: dts: rockchip: Fix broken tsadc pinctrl names for rk3588
Link: https://lore.kernel.org/r/3004814.3ZeAukHxDK@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
If userspace creates vcpus, then a vgic, we end-up in a situation
where irqchip_in_kernel() will return true, but no private interrupt
has been allocated for these vcpus. This situation will continue
until userspace initialises the vgic, at which point we fix the
early vcpus. Should a vcpu run or be initialised in the interval,
bad things may happen.
An obvious solution is to move this fix-up phase to the point where
the vgic is created. This ensures that from that point onwards,
all vcpus have their private interrupts, as new vcpus will directly
allocate them.
With that, we have the invariant that when irqchip_in_kernel() is
true, all vcpus have their private interrupts.
Reported-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250212182558.2865232-3-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
We currently spit out a warning if making a timer interrupt pending
fails. But not only this is loud and easy to trigger from userspace,
we also fail to do anything useful with that information.
Dropping the warning is the easiest thing to do for now. We can
always add error reporting if we really want in the future.
Reported-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250212182558.2865232-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
When allocating guest stage-2 page-table pages at EL2, pKVM can consume
pages from the host-provided kvm_hyp_memcache. As pgtable.c expects
zeroed pages, guest_s2_zalloc_page() actively implements this zeroing
with a PAGE_SIZE memset. Unfortunately, we don't check the page
alignment of the host-provided address before doing so, which could
lead to the memset overrunning the page if the host was malicious.
Fix this by simply force-aligning all kvm_hyp_memcache allocations to
page boundaries.
Fixes: 60dfe093ec13 ("KVM: arm64: Instantiate guest stage-2 page-tables at EL2")
Reported-by: Ben Simner <ben.simner@cl.cam.ac.uk>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20250213153615.3642515-1-qperret@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Now that EL2 has gained some early timer emulation, it accesses
the offsets pointed to by the timer structure, both of which
live in the KVM structure.
Of course, these are *kernel* pointers, so the dereferencing
of these pointers in non-kernel code must be itself be offset.
Given switch.h its own version of timer_get_offset() and use that
instead.
Fixes: b86fc215dc26d ("KVM: arm64: Handle counter access early in non-HYP context")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20250212173454.2864462-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
At the end of kvm_arch_vcpu_load_fp() we check that no bits are set in
SVCR. We only check this for protected mode despite this mattering
equally for non-protected mode, and the comment above this is confusing.
Remove the comment and simplify the check, moving from WARN_ON() to
WARN_ON_ONCE() to avoid spamming the log.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
In non-protected KVM modes, while the guest FPSIMD/SVE/SME state is live on the
CPU, the host's active SVE VL may differ from the guest's maximum SVE VL:
* For VHE hosts, when a VM uses NV, ZCR_EL2 contains a value constrained
by the guest hypervisor, which may be less than or equal to that
guest's maximum VL.
Note: in this case the value of ZCR_EL1 is immaterial due to E2H.
* For nVHE/hVHE hosts, ZCR_EL1 contains a value written by the guest,
which may be less than or greater than the guest's maximum VL.
Note: in this case hyp code traps host SVE usage and lazily restores
ZCR_EL2 to the host's maximum VL, which may be greater than the
guest's maximum VL.
This can be the case between exiting a guest and kvm_arch_vcpu_put_fp().
If a softirq is taken during this period and the softirq handler tries
to use kernel-mode NEON, then the kernel will fail to save the guest's
FPSIMD/SVE state, and will pend a SIGKILL for the current thread.
This happens because kvm_arch_vcpu_ctxsync_fp() binds the guest's live
FPSIMD/SVE state with the guest's maximum SVE VL, and
fpsimd_save_user_state() verifies that the live SVE VL is as expected
before attempting to save the register state:
| if (WARN_ON(sve_get_vl() != vl)) {
| force_signal_inject(SIGKILL, SI_KERNEL, 0, 0);
| return;
| }
Fix this and make this a bit easier to reason about by always eagerly
switching ZCR_EL{1,2} at hyp during guest<->host transitions. With this
happening, there's no need to trap host SVE usage, and the nVHE/nVHE
__deactivate_cptr_traps() logic can be simplified to enable host access
to all present FPSIMD/SVE/SME features.
In protected nVHE/hVHE modes, the host's state is always saved/restored
by hyp, and the guest's state is saved prior to exit to the host, so
from the host's PoV the guest never has live FPSIMD/SVE/SME state, and
the host's ZCR_EL1 is never clobbered by hyp.
Fixes: 8c8010d69c132273 ("KVM: arm64: Save/restore SVE state for nVHE")
Fixes: 2e3cf82063a00ea0 ("KVM: arm64: nv: Ensure correct VL is loaded before saving SVE state")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250210195226.1215254-9-mark.rutland@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
The shared hyp switch header has a number of static functions which
might not be used by all files that include the header, and when unused
they will provoke compiler warnings, e.g.
| In file included from arch/arm64/kvm/hyp/nvhe/hyp-main.c:8:
| ./arch/arm64/kvm/hyp/include/hyp/switch.h:703:13: warning: 'kvm_hyp_handle_dabt_low' defined but not used [-Wunused-function]
| 703 | static bool kvm_hyp_handle_dabt_low(struct kvm_vcpu *vcpu, u64 *exit_code)
| | ^~~~~~~~~~~~~~~~~~~~~~~
| ./arch/arm64/kvm/hyp/include/hyp/switch.h:682:13: warning: 'kvm_hyp_handle_cp15_32' defined but not used [-Wunused-function]
| 682 | static bool kvm_hyp_handle_cp15_32(struct kvm_vcpu *vcpu, u64 *exit_code)
| | ^~~~~~~~~~~~~~~~~~~~~~
| ./arch/arm64/kvm/hyp/include/hyp/switch.h:662:13: warning: 'kvm_hyp_handle_sysreg' defined but not used [-Wunused-function]
| 662 | static bool kvm_hyp_handle_sysreg(struct kvm_vcpu *vcpu, u64 *exit_code)
| | ^~~~~~~~~~~~~~~~~~~~~
| ./arch/arm64/kvm/hyp/include/hyp/switch.h:458:13: warning: 'kvm_hyp_handle_fpsimd' defined but not used [-Wunused-function]
| 458 | static bool kvm_hyp_handle_fpsimd(struct kvm_vcpu *vcpu, u64 *exit_code)
| | ^~~~~~~~~~~~~~~~~~~~~
| ./arch/arm64/kvm/hyp/include/hyp/switch.h:329:13: warning: 'kvm_hyp_handle_mops' defined but not used [-Wunused-function]
| 329 | static bool kvm_hyp_handle_mops(struct kvm_vcpu *vcpu, u64 *exit_code)
| | ^~~~~~~~~~~~~~~~~~~
Mark these functions as 'inline' to suppress this warning. This
shouldn't result in any functional change.
At the same time, avoid the use of __alias() in the header and alias
kvm_hyp_handle_iabt_low() and kvm_hyp_handle_watchpt_low() to
kvm_hyp_handle_memory_fault() using CPP, matching the style in the rest
of the kernel. For consistency, kvm_hyp_handle_memory_fault() is also
marked as 'inline'.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250210195226.1215254-8-mark.rutland@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
The hyp exit handling logic is largely shared between VHE and nVHE/hVHE,
with common logic in arch/arm64/kvm/hyp/include/hyp/switch.h. The code
in the header depends on function definitions provided by
arch/arm64/kvm/hyp/vhe/switch.c and arch/arm64/kvm/hyp/nvhe/switch.c
when they include the header.
This is an unusual header dependency, and prevents the use of
arch/arm64/kvm/hyp/include/hyp/switch.h in other files as this would
result in compiler warnings regarding missing definitions, e.g.
| In file included from arch/arm64/kvm/hyp/nvhe/hyp-main.c:8:
| ./arch/arm64/kvm/hyp/include/hyp/switch.h:733:31: warning: 'kvm_get_exit_handler_array' used but never defined
| 733 | static const exit_handler_fn *kvm_get_exit_handler_array(struct kvm_vcpu *vcpu);
| | ^~~~~~~~~~~~~~~~~~~~~~~~~~
| ./arch/arm64/kvm/hyp/include/hyp/switch.h:735:13: warning: 'early_exit_filter' used but never defined
| 735 | static void early_exit_filter(struct kvm_vcpu *vcpu, u64 *exit_code);
| | ^~~~~~~~~~~~~~~~~
Refactor the logic such that the header doesn't depend on anything from
the C files. There should be no functional change as a result of this
patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250210195226.1215254-7-mark.rutland@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
For historical reasons, the VHE and nVHE/hVHE implementations of
__activate_cptr_traps() pair with a common implementation of
__kvm_reset_cptr_el2(), which ideally would be named
__deactivate_cptr_traps().
Rename __kvm_reset_cptr_el2() to __deactivate_cptr_traps(), and split it
into separate VHE and nVHE/hVHE variants so that each can be paired with
its corresponding implementation of __activate_cptr_traps().
At the same time, fold kvm_write_cptr_el2() into its callers. This
makes it clear in-context whether a write is made to the CPACR_EL1
encoding or the CPTR_EL2 encoding, and removes the possibility of
confusion as to whether kvm_write_cptr_el2() reformats the sysreg fields
as cpacr_clear_set() does.
In the nVHE/hVHE implementation of __activate_cptr_traps(), placing the
sysreg writes within the if-else blocks requires that the call to
__activate_traps_fpsimd32() is moved earlier, but as this was always
called before writing to CPTR_EL2/CPACR_EL1, this should not result in a
functional change.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250210195226.1215254-6-mark.rutland@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
When KVM is in VHE mode, the host kernel tries to save and restore the
configuration of CPACR_EL1.SMEN (i.e. CPTR_EL2.SMEN when HCR_EL2.E2H=1)
across kvm_arch_vcpu_load_fp() and kvm_arch_vcpu_put_fp(), since the
configuration may be clobbered by hyp when running a vCPU. This logic
has historically been broken, and is currently redundant.
This logic was originally introduced in commit:
861262ab86270206 ("KVM: arm64: Handle SME host state when running guests")
At the time, the VHE hyp code would reset CPTR_EL2.SMEN to 0b00 when
returning to the host, trapping host access to SME state. Unfortunately,
this was unsafe as the host could take a softirq before calling
kvm_arch_vcpu_put_fp(), and if a softirq handler were to use kernel mode
NEON the resulting attempt to save the live FPSIMD/SVE/SME state would
result in a fatal trap.
That issue was limited to VHE mode. For nVHE/hVHE modes, KVM always
saved/restored the host kernel's CPACR_EL1 value, and configured
CPTR_EL2.TSM to 0b0, ensuring that host usage of SME would not be
trapped.
The issue above was incidentally fixed by commit:
375110ab51dec5dc ("KVM: arm64: Fix resetting SME trap values on reset for (h)VHE")
That commit changed the VHE hyp code to configure CPTR_EL2.SMEN to 0b01
when returning to the host, permitting host kernel usage of SME,
avoiding the issue described above. At the time, this was not identified
as a fix for commit 861262ab86270206.
Now that the host eagerly saves and unbinds its own FPSIMD/SVE/SME
state, there's no need to save/restore the state of the EL0 SME trap.
The kernel can safely save/restore state without trapping, as described
above, and will restore userspace state (including trap controls) before
returning to userspace.
Remove the redundant logic.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20250210195226.1215254-5-mark.rutland@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
