| Age | Commit message (Collapse) | Author |
|---|
|
Add temperature sensor and thermal-zones support for
the StarFive JH7100 SoC.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
v1.3B:
v1.3B uses motorcomm YT8531(rgmii-id phy) x2, need delay and
inverse configurations.
The tx_clk of v1.3B uses an external clock and needs to be
switched to an external clock source.
v1.2A:
v1.2A gmac0 uses motorcomm YT8531(rgmii-id) PHY, and needs delay
configurations.
v1.2A gmac1 uses motorcomm YT8512(rmii) PHY, and needs to
switch rx and rx to external clock sources.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
[conor: squashed a fix from Samin to use the actual properties]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add JH7110 ethernet device node to support gmac driver for the JH7110
RISC-V SoC.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add PLL clocks input from PLL clocks driver in SYSCRG node.
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add stg_syscon/sys_syscon/aon_syscon/PLL nodes for JH7110 SoC.
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Co-developed-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add STGCRG/ISPCRG/VOUTCRG new node to support JH7110
System-Top-Group, Image-Signal-Process and Video-Output
clock and reset drivers for the JH7110 RISC-V SoC.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add DVP and HDMI TX pixel external fixed clocks and the rates are
74.25MHz and 297MHz.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add the '-@' DTC option for the starfive devices. This option
populates the '__symbols__' node that contains all the necessary symbols
for supporting device-tree overlays (for instance from the firmware or
the bootloader) on these devices.
The starfive devices allow various modules to be connected and this
enables users to create out-of-tree device-tree overlays for these modules.
Please note that this change does increase the size of the resulting DTB
by ~20%. For example, with v6.4 increase in size is as follows:
jh7100-beaglev-starlight.dtb 6192 -> 7339
jh7100-starfive-visionfive-v1.dtb 6281 -> 7428
jh7110-starfive-visionfive-2-v1.2a.dtb 11101 -> 13447
jh7110-starfive-visionfive-2-v1.3b.dtb 11101 -> 13447
Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.5 Part 2
T-Head:
Add a basic dtsi, Kconfig bits & trivial binding additions for the T-Head
1520 SoC (codename "light"). This SoC can be found on the Lichee Pi 4a,
for which a minimal dts is added.
Misc:
Re-sort the dts Makefile to be in alphanumerical order by directory.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
dt-bindings: riscv: Add T-HEAD TH1520 board compatibles
dt-bindings: timer: Add T-HEAD TH1520 clint
dt-bindings: interrupt-controller: Add T-HEAD's TH1520 PLIC
Link: https://lore.kernel.org/r/20230620-fidelity-variety-60b47c889e31@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.5
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: Add cpu scaling for JH7110 SoC
riscv: dts: starfive: Enable axp15060 pmic for cpufreq
dt-bindings: interrupt-controller: sifive,plic: Sort compatible values
dt-bindings: timer: sifive,clint: Clean up compatible value section
riscv: dts: starfive: jh7110: Add watchdog node
riscv: dts: starfive: jh7100: Add watchdog node
riscv: dts: starfive: Add PMU controller node
MAINTAINERS: exclude maintained subdirs in RISC-V misc DT entry
Link: https://lore.kernel.org/r/20230612-fasting-floss-0bc05a08bc7a@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
New additions to the list have tried to respect alphanumeric ordering,
but the thing was out of order to start with. Sort it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Jisheng Zhang <jszhang@kernel.org> says:
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
This also pulls in -rc2, because of some maintainers re-jigging that
went on in the interim in commit 80e62bc8487b ("MAINTAINERS: re-sort
all entries and fields").
Link: https://lore.kernel.org/r/20230617161529.2092-1-jszhang@kernel.org
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add initial device tree for the TH1520 RISC-V SoC by T-HEAD.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add the operating-points-v2 to support cpu scaling on StarFive JH7110 SoC.
It supports up to 4 cpu frequency loads.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The VisionFive 2 board has an embedded pmic axp15060,
which supports the cpu DVFS through the dcdc2 regulator.
This patch enables axp15060 pmic and configs the dcdc2.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Some boards form the MangoPi family (MQ\MQ-Dual\MQ-R) may have
an optional SPI flash that connects to the SPI0 controller.
This controller is the same for R329/D1/R528/T113s SoCs and
should be supported by the sun50i-r329-spi driver.
So let's add its DT nodes.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230510081121.3463710-6-bigunclemax@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
Add the watchdog node for the Starfive JH7110 SoC.
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Reviewed-by: Walker Chen <walker.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add watchdog node for the StarFive JH7100 RISC-V SoC.
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add the pmu controller node for the StarFive JH7110 SoC. The PMU needs
to be used by other modules, e.g. VPU,ISP,etc.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Walker Chen <walker.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek,
NXP, Rockchips, Renesas, TI, Samsung and ST Microelectronics. These
all add new features for existing machines, as well as new machines
and SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V based D1
chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core like its
JH7100 predecessor, but with additional CPU cores and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini gets
added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs, based on
the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the Snapdragon
family.
Including the initial board support for the added SoC platforms, there
are 52 new machines. The largest group are 19 boards industrial
embedded boards based on the NXP i.MX6 (32-bit) and i.MX8 (64-bit)
families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three 'Banana Pi' variants based on the Amlogic g12b (A311D, S922X)
SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs, including
the rk3588s-khadas-edge2 and a few NanoPi models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete 'oxnas'
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the
Qualcomm Sc7180 'trogdor' design that were never part of products"
* tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (836 commits)
arm64: dts: rockchip: Add support for volume keys to rk3399-pinephone-pro
arm64: dts: rockchip: Add vdd_cpu_big regulators to rk3588-rock-5b
arm64: dts: rockchip: Use generic name for es8316 on Pinebook Pro and Rock 5B
arm64: dts: rockchip: Drop RTC clock-frequency on rk3588-rock-5b
arm64: dts: apple: t8112: Add PWM controller
arm64: dts: apple: t600x: Add PWM controller
arm64: dts: apple: t8103: Add PWM controller
arm64: dts: rockchip: Add pinctrl gpio-ranges for rk356x
ARM: dts: nomadik: Replace deprecated spi-gpio properties
ARM: dts: aspeed-g6: Add UDMA node
ARM: dts: aspeed: greatlakes: add mctp device
ARM: dts: aspeed: greatlakes: Add gpio names
ARM: dts: aspeed: p10bmc: Change power supply info
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMM050 Magnetometer
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMA255 Accelerometer
arm64: dts: mediatek: mt6795: Add tertiary PWM node
arm64: dts: rockchip: add panel to Anbernic RG353 series
dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC
dt-bindings: arm: fsl: Add chargebyte Tarragon
dt-bindings: vendor-prefixes: add chargebyte
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
- added D1 crypto node
- enabled DVFS on OrangePi PC2 board
- added GPIO line names on Nezha D1 board
- added suniv USB nodes and enabled on licheepi-nano
- new suniv boards: PopStick v1.1 and Lctech Pi
- added Allwinner T113-s DTSI
- added MangoPi MQ-R T113-s board variant
- swapped DMA names for A23, A31, A33, D1, H3, H5, V3s
* tag 'sunxi-dt-for-6.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
riscv: dts: allwinner: d1: Switch dma-names order for snps,dw-apb-uart nodes
ARM: dts: sunxi: h3/h5: Switch dma-names order for snps,dw-apb-uart nodes
ARM: dts: sun8i: v3s: Switch dma-names order for snps,dw-apb-uart nodes
ARM: dts: sun8i: a23/a33: Switch dma-names order for snps,dw-apb-uart nodes
ARM: dts: sun6i: a31: Switch dma-names order for snps,dw-apb-uart nodes
ARM: dts: sunxi: add MangoPi MQ-R-T113 board
dt-bindings: arm: sunxi: document MangoPi MQ-R board names
ARM: dts: sunxi: add Allwinner T113-s SoC .dtsi
dts: add riscv include prefix link
ARM: dts: suniv: Add Lctech Pi F1C200s devicetree
ARM: dts: suniv: add device tree for PopStick v1.1
dt-binding: arm: sunxi: add two board compatible strings
dt-bindings: vendor-prefixes: add Source Parts and Lctech names
ARM: dts: suniv: licheepi-nano: enable USB
ARM: dts: suniv: add USB-related device nodes
riscv: dts: nezha-d1: add gpio-line-names
arm64: dts: allwinner: h5: OrangePi PC2: add OPP table to enable DVFS
riscv: dts: allwinner: d1: Add crypto engine node
Link: https://lore.kernel.org/r/20230408125156.GA17050@jernej-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 370f696e4474 ("dt-bindings: serial: snps-dw-apb-uart: add dma &
dma-names properties") documented dma-names property to handle Allwinner
D1 dtbs_check warnings, but relies on the rx->tx ordering, which is the
reverse of what a bunch of different boards expect.
The initial proposed solution was to allow a flexible dma-names order in
the binding, due to potential ABI breakage concerns after fixing the DTS
files. But luckily the Allwinner boards are not affected, since they are
using a shared DMA channel for rx and tx.
Hence, the first step in fixing the inconsistency was to change
dma-names order in the binding to tx->rx.
Do the same for the snps,dw-apb-uart nodes in the DTS file.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230321215624.78383-7-cristian.ciocaltea@collabora.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
Merge Hal's series adding support for the new StarFive JH7110 SoC.
There's a few bindings here for core components that were not picked up
by the various maintainers for the subsystems (previously Palmer would
pick these up via the RISC-V tree) & the first two commits in the branch
are shared with the clk tree, since the dts depends on defines in the
dt-binding headers.
This is based on -rc2, as the board does not actually boot on -rc1
due to the bug Linus introduced.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add a minimal device tree for StarFive JH7110 VisionFive 2 board
which has version A and version B. Support booting and basic
clock/reset/pinctrl/uart drivers.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Co-developed-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Co-developed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add pin function definitions for StarFive JH7110 SoC.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add initial device tree for the JH7110 RISC-V SoC by StarFive
Technology Ltd.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Co-developed-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Co-developed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
[conor: squashed in the removal of the S7's non-existent mmu]
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The spi-max-frequency is a property of SPI children, not the
controller:
k210_generic.dtb: spi@50240000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The mailbox on PolarFire SoC should really have three reg properties,
not two. Without splitting into three sections, the system controller's
QSPI cannot be accessed as it sits inside the current first range. The
driver & binding have been adapted to account for both two & three
ranges, so fix the dts too.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add descriptive names so users can associate specific lines with their
respective pins on the 40-pin header according to the schematics.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Link: http://dl.linux-sunxi.org/D1/D1_Nezha_development_board_schematic_diagram_20210224.pdf
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230210025132.36605-2-twoerner@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
D1 contains a crypto engine which is supported by the sun8i-ce driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221231220146.646-4-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The macb on PolarFire SoC has reset support which the generic compatible
does not use. Add the newly introduced MPFS specific compatible as the
primary compatible to avail of this support & wire up the reset to the
clock controllers devicetree entry.
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
- introduce Allwinner D1 DTSI
- add boards: Dongshan Nezha STU, MangoPi MQ (Pro), Sipeed Lichee RV,
Nezha
- add D1 power controller node
- Add SATA regulator to Bananapi M3
- fix regulator reference for nanopi-duo2
- fix GPIO node names
- align HDMI CEC node name for h3-beelink-x2
- add DPHY interrupt to A64 and A33
* tag 'sunxi-dt-for-6.3-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
riscv: dts: allwinner: d1: Add power controller node
riscv: Add the Allwinner SoC family Kconfig option
riscv: dts: allwinner: Add Dongshan Nezha STU devicetree
riscv: dts: allwinner: Add MangoPi MQ Pro devicetree
riscv: dts: allwinner: Add Sipeed Lichee RV devicetrees
riscv: dts: allwinner: Add Allwinner D1 Nezha devicetree
riscv: dts: allwinner: Add MangoPi MQ devicetree
riscv: dts: allwinner: Add the D1/D1s SoC devicetree
dt-bindings: riscv: Add Allwinner D1/D1s board compatibles
dt-bindings: vendor-prefixes: Add Allwinner D1/D1s board vendors
MAINTAINERS: Match the sun20i family of Allwinner SoCs
ARM: dts: sun8i: a83t: bananapi-m3: describe SATA disk regulator
ARM: dts: sun8i: nanopi-duo2: Fix regulator GPIO reference
ARM: dts: sunxi: Fix GPIO LED node names
ARM: dts: sun8i: h3-beelink-x2: align HDMI CEC node names with dtschema
arm64: dts: allwinner: a64: Add DPHY interrupt
ARM: dts: sun8i: a33: Add DPHY interrupt
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT updates for v6.3 (take two)
- High Performance mode (1.8 GHz) support for the Cortex-A76 CPU cores
on R-Car V4H,
- GPIO interrupt support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- USB Function support for the RZ/N1D SoC,
- Generic Sound Card driver examples for the Renesas R-Car Starter Kit
Premier/Pro and Shimafugi Kingfisher development board stack,
- Universal Flash Storage support for the Renesas Spider development
board,
- External Power Sequence Controller (PWC) support for the RZ/V2M SoC
and the RZ/V2M Evaluation Kit 2.0,
- IOMMU support for MMC on the R-Car S4-8 SoC,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (25 commits)
arm64: dts: renesas: r8a779f0: Add iommus to MMC node
arm64: dts: renesas: v2mevk2: Add PWC support
arm64: dts: renesas: r9a09g011: Add PWC support
arm64: dts: renesas: r9a09g011: Reword ethernet status
arm64: dts: renesas: r8a774[be]1-beacon: Sync aliases with RZ/G2M
arm64: dts: renesas: beacon-renesom: Fix audio clock rate
arm64: dts: renesas: beacon-renesom: Update Ethernet PHY ID
arm64: dts: renesas: beacon-renesom: Fix gpio expander reference
arm64: dts: renesas: spider-cpu: Enable UFS device
arm64: dts: renesas: Add ulcb{-kf} Simple Audio Card MIX + TDM Split dtsi
arm64: dts: renesas: Add ulcb{-kf} Audio Graph Card MIX + TDM Split dtsi
arm64: dts: renesas: Add ulcb{-kf} Audio Graph Card2 MIX + TDM Split dtsi
arm64: dts: renesas: Add ulcb{-kf} Simple Audio Card dtsi
arm64: dts: renesas: Add ulcb{-kf} Audio Graph Card2 dtsi
arm64: dts: renesas: Add ulcb{-kf} Audio Graph Card dtsi
arm64: dts: renesas: #sound-dai-cells is used when simple-card
ARM: dts: renesas: #sound-dai-cells is used when simple-card
arm64: dts: renesas: eagle: Add SCIF_CLK support
ARM: dts: r9a06g032: Add the USBF controller node
arm64: dts: renesas: rzg2ul-smarc-som: Add PHY interrupt support for ETH{0/1}
...
Link: https://lore.kernel.org/r/cover.1674815099.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/dt
RISC-V Devicetrees for v6.3-mw0
Microchip:
A vendor prefix for Aldec and both a binding and Devicetree for the
Aldec TySoM devkit for PolarFire SoC. This Devicetree corresponds to
what they are shipping in the SDK for rev2 boards.
StarFive:
Just the binding for the new StarFive JH7110 SoC and its first-party
SDC the VisionFive 2.
Other:
I was expecting the Devicetree for the aforementioned board to be ready
for this window, as the pinctrl driver had seem some review prior to
v6.2 and both it & the base clock drivers are heavily based on the
existing drivers for the JH7110.
That didn't come to be.. Christmas, the RISC-V Summit in December and
the Lunar New Year all playing a part perhaps.
Because of that, both Palmer and I have the Kconfig.socs work in our
branches, although in hindsight it probably wasn't needed here as I
only added the TySoM Devicetree & the conflict would've been trivial.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.3-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: microchip: add the Aldec TySoM's devicetree
dt-bindings: riscv: microchip: document the Aldec TySoM
dt-bindings: vendor-prefixes: Add entry for Aldec
RISC-V: stop directly selecting drivers for SOC_CANAAN
RISC-V: stop selecting SiFive clock and serial drivers directly
RISC-V: stop selecting the PolarFire SoC clock driver
RISC-V: kbuild: convert all use of SOC_FOO to ARCH_FOO
RISC-V: kconfig.socs: convert usage of SOC_CANAAN to ARCH_CANAAN
RISC-V: introduce ARCH_FOO kconfig aliases for SOC_FOO symbols
dt-bindings: riscv: Add StarFive JH7110 SoC and VisionFive 2 board
Link: https://lore.kernel.org/r/Y9LP+Za1h0fkBa58@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The Allwinner D1 family of SoCs contain a PPU power domain controller
separate from the PRCM. It can power down the video engine and DSP, and
it contains special logic for hardware-assisted CPU idle.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230126063419.15971-4-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The 100ask Dongshan Nezha STU is a system-on-module that can be used
standalone or with a carrier board. The SoM provides gigabit Ethernet,
HDMI, a USB peripheral port, and WiFi/Bluetooth via an RTL8723DS chip.
The "DIY" carrier board exposes almost every pin from the D1 SoC to 0.1"
headers, but contains no digital circuitry, so it does not have its own
devicetree.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-10-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The MangoPi MQ Pro is a tiny SBC with a layout compatible to the
Raspberry Pi Zero. It includes the Allwinner D1 SoC, 512M or 1G of DDR3,
and an RTL8723DS-based WiFi/Bluetooth module.
The board also exposes GPIO Port E via a connector on the end of the
board, which can support either a camera or an RMII Ethernet PHY. The
additional regulators supply that connector.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-9-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
Sipeed manufactures a "Lichee RV" system-on-module, which provides a
minimal working system on its own, as well as a few carrier boards. The
"Dock" board provides audio, USB, and WiFi. The "86 Panel" additionally
provides 100M Ethernet and a built-in display panel.
The 86 Panel repurposes the USB ID and VBUS detection GPIOs for its RGB
panel interface, since the USB OTG port is inaccessible inside the case.
Co-developed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-8-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
"D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
plus low-speed I/O from the SoC and a GPIO expander chip.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-7-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The MangoPi MQ is a tiny SBC built around the Allwinner D1s. Its
onboard peripherals include two USB Type-C ports (1 device, 1 host)
and RTL8189FTV WLAN.
A MangoPi MQ-R variant of the board also exists. The MQ-R has a
different form factor, but the onboard peripherals are the same.
Most D1 and D1s boards use a similar power tree, with the 1.8V rail
powered by the SoC's internal LDOA, analog domains powered by ALDO,
and the rest of the board powered by always-on fixed regulators. To
avoid duplication, factor out the regulator information that is
common across boards.
The board also exposes GPIO Port E via a FPC connector, which can
support either a camera or an RMII Ethernet PHY. The additional
regulators supply that connector.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-6-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs based
on a single die, or at a pair of dies derived from the same design.
D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 and
T113 contain a pair of Cortex-A7's. D1 and R528 are the full version of
the chip with a BGA package, whereas D1s and T113 are low-pin-count QFP
variants.
Because the original design supported both ARM and RISC-V CPUs, some
peripherals are duplicated. In addition, all variants except D1s contain
a HiFi 4 DSP with its own set of peripherals.
The devicetrees are organized to minimize duplication:
- Common perhiperals are described in sunxi-d1s-t113.dtsi
- DSP-related peripherals are described in sunxi-d1-t113.dtsi
- RISC-V specific hardware is described in sun20i-d1s.dtsi
- Functionality unique to the D1 variant is described in sun20i-d1.dtsi
The SOC_PERIPHERAL_IRQ macro handles the different #interrupt-cells
values between the ARM (GIC) and RISC-V (PLIC) versions of the SoC.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Tested-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-5-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
IRQC support for RZ/Five is still missing so drop the interrupts and
interrupt-parent properties from the PHY nodes of ETH{0,1}.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230102222708.274369-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
As it says on the tin, add a DT for this board. It's been sitting on my
desk for a while, so may as well have it upstream...
The DT is only partially complete, as it needs the fabric content added.
Unfortunately, I don't have a reference design in RTL or SmartDesign
for it and therefore don't know what that fabric content is.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The TySOM-M-MPFS250 is a compact SoC prototyping board featuring
a Microchip PolarFire SoC MPFS250T-FCG1152. Features include:
- 16 Gib FPGA DDR4
- 16 Gib MSS DDR4 with ECC
- eMMC
- SPI flash memory
- 2x Ethernet 10/100/1000
- USB 2.0
- PCIe x4 Gen2
- HDMI OUT
- 2x FMC connector (HPC and LPC)
Specifically flag this board as rev2, in case later boards have an
FPGA design revision with more features available in the future.
Link: https://www.aldec.com/en/products/emulation/tysom_boards/polarfire_microchip/tysom_m_mpfs250
[Fixed a mistake where I read 16 Gib as 16 GiB!]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Enable OSTM{1,2} nodes on RZ/Five SMARC SoM.
Note, OSTM{1,2} nodes are enabled in the RZ/G2UL SMARC SoM DTSI [0] hence
deleting the disabled nodes from RZ/Five SMARC SoM DTSI enables it here
too as we include [0] in RZ/Five SMARC SoM DTSI.
[0] arch/arm64/boot/dts/renesas/rzg2ul-smarc-som.dtsi
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230102222233.274021-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The 32-bit memory resource is needed for non-prefetchable memory
allocations on the PCIe bus, however with some cards (such as the
SM768) the system fails to allocate memory from this.
Checking the allocation against the datasheet, it looks like there
has been a mis-calcualation of the resource for the first memory
region (0x0060090000..0x0070ffffff) which in the data-sheet for
the fu740 (v1p2) is from 0x0060000000..0x007fffffff. Changing
this to allocate from 0x0060090000..0x007fffffff fixes the probing
issues.
Fixes: ae80d5148085 ("riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC")
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: stable@vger.kernel.org
Tested-by: Ron Economos <re@w6rz.net> # from IRC
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Convert all non user visible use of SOC_FOO symbols to their ARCH_FOO
variants. The canaan DTs are an outlier in that they're gated at the
directory and the file level. Drop the directory level gating while we
are swapping the symbol names over.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Enable WDT node on RZ/Five SMARC SoM.
Note, WDT block is enabled in RZ/G2UL SMARC SoM DTSI [0] hence deleting
the disabled node from RZ/Five SMARC SoM DTSI enables it here too as we
include [0] in RZ/Five SMARC SoM DTSI.
[0] arch/arm64/boot/dts/renesas/rzg2ul-smarc-som.dtsi
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221118135715.14410-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
