summaryrefslogtreecommitdiff
path: root/drivers/bluetooth/btusb.c
AgeCommit message (Collapse)Author
2025-03-07Bluetooth: btusb: Configure altsetting for HCI_USER_CHANNELHsin-chen Chuang
Automatically configure the altsetting for HCI_USER_CHANNEL when a SCO is connected. The motivation is to enable the HCI_USER_CHANNEL user to send out SCO data through USB Bluetooth chips, which is mainly used for bidirectional audio transfer (voice call). This was not capable because: - Per Bluetooth Core Spec v5, Vol 4, Part B, 2.1, the corresponding alternate setting should be set based on the air mode in order to transfer SCO data, but - The Linux Bluetooth HCI_USER_CHANNEL exposes the Bluetooth Host Controller Interface to the user space, which is something above the USB layer. The user space is not able to configure the USB alt while keeping the channel open. This patch intercepts the HCI_EV_SYNC_CONN_COMPLETE packets in btusb, extracts the air mode, and configures the alt setting in btusb. This patch is tested on ChromeOS devices. The USB Bluetooth models (CVSD, TRANS alt3 and alt6) could work without a customized kernel. Fixes: b16b327edb4d ("Bluetooth: btusb: add sysfs attribute to control USB alt setting") Signed-off-by: Hsin-chen Chuang <chharry@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-02-27bluetooth: btusb: Initialize .owner field of force_poll_sync_fopsSalah Triki
Initialize .owner field of force_poll_sync_fops to THIS_MODULE in order to prevent btusb from being unloaded while its operations are in use. Fixes: 800fe5ec302e ("Bluetooth: btusb: Add support for queuing during polling interval") Signed-off-by: Salah Triki <salah.triki@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-02-20Bluetooth: Always allow SCO packets for user channelHsin-chen Chuang
The SCO packets from Bluetooth raw socket are now rejected because hci_conn_num is left 0. This patch allows such the usecase to enable the userspace SCO support. Fixes: b16b327edb4d ("Bluetooth: btusb: add sysfs attribute to control USB alt setting") Signed-off-by: Hsin-chen Chuang <chharry@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-29Bluetooth: Fix possible infinite recursion of btusb_resetHsin-chen Chuang
The function enters infinite recursion if the HCI device doesn't support GPIO reset: btusb_reset -> hdev->reset -> vendor_reset -> btusb_reset... btusb_reset shouldn't call hdev->reset after commit f07d478090b0 ("Bluetooth: Get rid of cmd_timeout and use the reset callback") Fixes: f07d478090b0 ("Bluetooth: Get rid of cmd_timeout and use the reset callback") Signed-off-by: Hsin-chen Chuang <chharry@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-29Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface()Douglas Anderson
The documentation for usb_driver_claim_interface() says that "the device lock" is needed when the function is called from places other than probe(). This appears to be the lock for the USB interface device. The Mediatek btusb code gets called via this path: Workqueue: hci0 hci_power_on [bluetooth] Call trace: usb_driver_claim_interface btusb_mtk_claim_iso_intf btusb_mtk_setup hci_dev_open_sync hci_power_on process_scheduled_works worker_thread kthread With the above call trace the device lock hasn't been claimed. Claim it. Without this fix, we'd sometimes see the error "Failed to claim iso interface". Sometimes we'd even see worse errors, like a NULL pointer dereference (where `intf->dev.driver` was NULL) with a trace like: Call trace: usb_suspend_both usb_runtime_suspend __rpm_callback rpm_suspend pm_runtime_work process_scheduled_works Both errors appear to be fixed with the proper locking. Fixes: ceac1cb0259d ("Bluetooth: btusb: mediatek: add ISO data transmission functions") Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-15Bluetooth: Get rid of cmd_timeout and use the reset callbackHsin-chen Chuang
The hdev->reset is never used now and the hdev->cmd_timeout actually does reset. This patch changes the call path from hdev->cmd_timeout -> vendor_cmd_timeout -> btusb_reset -> hdev->reset , to hdev->reset -> vendor_reset -> btusb_reset Which makes it clear when we export the hdev->reset to a wider usage e.g. allowing reset from sysfs. This patch doesn't introduce any behavior change. Signed-off-by: Hsin-chen Chuang <chharry@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-15Bluetooth: Remove the cmd timeout count in btusbHsin-chen Chuang
Remove the cmd timeout count in btusb since we only ever allow one command in flight at a time. We should always reset after a single command times out. Signed-off-by: Hsin-chen Chuang <chharry@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-15Bluetooth: btusb: Add RTL8851BE device 13d3:3600Garrett Wilke
The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3600 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Garrett Wilke <garrett@system76.com> Signed-off-by: Tim Crawford <tcrawford@system76.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-15Bluetooth: btusb: Add MT7921e device 13d3:3576Garrett Wilke
The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3576 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Garrett Wilke <garrett@system76.com> Signed-off-by: Tim Crawford <tcrawford@system76.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-15Bluetooth: btusb: Add new VID/PID 13d3/3628 for MT7925En-Wei Wu
Add VID 13d3 & PID 3628 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3628 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-15Bluetooth: btusb: Add new VID/PID 13d3/3610 for MT7922Andrew Halaney
A new machine has a Archer AX3000 / TX55e in it, and out the box reported issues resetting hci0. It looks like this is a MT7922 from the lspci output, so treat it as a MediaTek device and use the proper callbacks. With that in place an xbox controller can be used without issue as seen below: [ 7.047388] Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512 [ 9.583883] Bluetooth: hci0: Device setup in 2582842 usecs [ 9.583895] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. [ 9.644780] Bluetooth: hci0: AOSP extensions version v1.00 [ 9.644784] Bluetooth: hci0: AOSP quality report is supported [ 876.379876] input: Xbox Wireless Controller as /devices/virtual/misc/uhid/0005:045E:0B13.0006/input/input27 [ 876.380215] hid-generic 0005:045E:0B13.0006: input,hidraw3: BLUETOOTH HID v5.15 Gamepad [Xbox Wireless Controller] on c0:bf:be:27:de:f7 [ 876.429368] input: Xbox Wireless Controller as /devices/virtual/misc/uhid/0005:045E:0B13.0006/input/input28 [ 876.429423] microsoft 0005:045E:0B13.0006: input,hidraw3: BLUETOOTH HID v5.15 Gamepad [Xbox Wireless Controller] on c0:bf:be:27:de:f7 lspci output: root@livingroom:/home/ajhalaney/git# lspci ... 05:00.0 Network controller: MEDIATEK Corp. MT7922 802.11ax PCI Express Wireless Network Adapter and USB device: root@livingroom:/home/ajhalaney/git# cat /sys/kernel/debug/usb/devices ... T: Bus=01 Lev=01 Prnt=01 Port=10 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3610 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Andrew Halaney <ajhalaney@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-15Bluetooth: btusb: add sysfs attribute to control USB alt settingYing Hsu
When a Bluetooth raw socket is open, the HCI event related to SCO connection changes are not dispatched to the hci_event module, and the underlying Bluetooth controller's USB Interface 1 will not be updated accordingly. This patch adds `isoc_alt` sysfs attribute, allowing user space to update the alternate setting of the USB interface alternate setting as needed. Signed-off-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-01-15Bluetooth: btusb: Add ID 0x2c7c:0x0130 for Qualcomm WCN785xMark Dietzer
Adds a new entry with VID 0x2c7c and PID 0x0130 to the btusb quirks table as it uses a Qualcomm WCN785x chipset The device information from /sys/kernel/debug/usb/devices is provided below: T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=05 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0130 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Mark Dietzer <git@doridian.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add 3 HWIDs for MT7925Jiande Lu
Add below HWIDs for MediaTek MT7925 USB Bluetooth chip. VID 0x0489, PID 0xe14f VID 0x0489, PID 0xe150 VID 0x0489, PID 0xe151 Patch has been tested successfully and controller is recognized device pair successfully. MT7925 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20240816133202 Bluetooth: hci0: Device setup in 286558 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Signed-off-by: Jiande Lu <jiande.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add new VID/PID 0489/e124 for MT7925Jonathan McCrohan
Add VID 0489 & PID e124 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=08 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e124 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add new VID/PID 0489/e111 for MT7925Hao Qin
Add VID 0489 & PID e111 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=02 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e111 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Hao Qin <hao.qin@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btmtk: adjust the position to init iso data anchorChris Lu
MediaTek iso data anchor init should be moved to where MediaTek claims iso data interface. If there is an unexpected BT usb disconnect during setup flow, it will cause a NULL pointer crash issue when releasing iso anchor since the anchor wasn't been init yet. Adjust the position to do iso data anchor init. [ 17.137991] pc : usb_kill_anchored_urbs+0x60/0x168 [ 17.137998] lr : usb_kill_anchored_urbs+0x44/0x168 [ 17.137999] sp : ffffffc0890cb5f0 [ 17.138000] x29: ffffffc0890cb5f0 x28: ffffff80bb6c2e80 [ 17.144081] gpio gpiochip0: registered chardev handle for 1 lines [ 17.148421] x27: 0000000000000000 [ 17.148422] x26: ffffffd301ff4298 x25: 0000000000000003 x24: 00000000000000f0 [ 17.148424] x23: 0000000000000000 x22: 00000000ffffffff x21: 0000000000000001 [ 17.148425] x20: ffffffffffffffd8 x19: ffffff80c0f25560 x18: 0000000000000000 [ 17.148427] x17: ffffffd33864e408 x16: ffffffd33808f7c8 x15: 0000000000200000 [ 17.232789] x14: e0cd73cf80ffffff x13: 50f2137c0a0338c9 x12: 0000000000000001 [ 17.239912] x11: 0000000080150011 x10: 0000000000000002 x9 : 0000000000000001 [ 17.247035] x8 : 0000000000000000 x7 : 0000000000008080 x6 : 8080000000000000 [ 17.254158] x5 : ffffffd33808ebc0 x4 : fffffffe033dcf20 x3 : 0000000080150011 [ 17.261281] x2 : ffffff8087a91400 x1 : 0000000000000000 x0 : ffffff80c0f25588 [ 17.268404] Call trace: [ 17.270841] usb_kill_anchored_urbs+0x60/0x168 [ 17.275274] btusb_mtk_release_iso_intf+0x2c/0xd8 [btusb (HASH:5afe 6)] [ 17.284226] btusb_mtk_disconnect+0x14/0x28 [btusb (HASH:5afe 6)] [ 17.292652] btusb_disconnect+0x70/0x140 [btusb (HASH:5afe 6)] [ 17.300818] usb_unbind_interface+0xc4/0x240 [ 17.305079] device_release_driver_internal+0x18c/0x258 [ 17.310296] device_release_driver+0x1c/0x30 [ 17.314557] bus_remove_device+0x140/0x160 [ 17.318643] device_del+0x1c0/0x330 [ 17.322121] usb_disable_device+0x80/0x180 [ 17.326207] usb_disconnect+0xec/0x300 [ 17.329948] hub_quiesce+0x80/0xd0 [ 17.333339] hub_disconnect+0x44/0x190 [ 17.337078] usb_unbind_interface+0xc4/0x240 [ 17.341337] device_release_driver_internal+0x18c/0x258 [ 17.346551] device_release_driver+0x1c/0x30 [ 17.350810] usb_driver_release_interface+0x70/0x88 [ 17.355677] proc_ioctl+0x13c/0x228 [ 17.359157] proc_ioctl_default+0x50/0x80 [ 17.363155] usbdev_ioctl+0x830/0xd08 [ 17.366808] __arm64_sys_ioctl+0x94/0xd0 [ 17.370723] invoke_syscall+0x6c/0xf8 [ 17.374377] el0_svc_common+0x84/0xe0 [ 17.378030] do_el0_svc+0x20/0x30 [ 17.381334] el0_svc+0x34/0x60 [ 17.384382] el0t_64_sync_handler+0x88/0xf0 [ 17.388554] el0t_64_sync+0x180/0x188 [ 17.392208] Code: f9400677 f100a2f4 54fffea0 d503201f (b8350288) [ 17.398289] ---[ end trace 0000000000000000 ]--- Fixes: ceac1cb0259d ("Bluetooth: btusb: mediatek: add ISO data transmission functions") Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: Set quirks for ATS2851Danil Pylaev
This adds quirks for broken ats2851 features. Signed-off-by: Danil Pylaev <danstiv404@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add USB HW IDs for MT7920/MT7925Jiande Lu
Add HW IDs for wireless module. These HW IDs are extracted from Windows driver inf file and the test for card bring up successful. MT7920 HW IDs test with below patch. https://patchwork.kernel.org/project/bluetooth/ patch/20240930081257.23975-1-chris.lu@mediatek.com/ Patch has been tested successfully and controller is recognized devices pair successfully. MT7920 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20240930111457 Bluetooth: hci0: Device setup in 143004 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: hci0: AOSP quality report is supported Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 MT7925 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20240816133202 Bluetooth: hci0: Device setup in 286558 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Signed-off-by: Jiande Lu <jiande.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add RTL8852BE device 0489:e123 to device tablesHilda Wu
Add the support ID 0489:e123 to usb_device_id table for Realtek RTL8852B chip. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e123 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14bluetooth: Fix typos in the commentsYan Zhen
Correctly spelled comments make it easier for the reader to understand the code. Fix typos: 'fragement' ==> 'fragment', 'genration' ==> 'generation', 'funciton' ==> 'function', 'Explitly' ==> 'Explicitly', 'explaination' ==> 'explanation', 'Tranlate' ==> 'Translate', 'immediatelly' ==> 'immediately', 'isntance' ==> 'instance', 'transmittion' ==> 'transmission', 'recevie' ==> 'receive', 'outselves' ==> 'ourselves', 'conrol' ==> 'control'. Signed-off-by: Yan Zhen <yanzhen@vivo.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add one more ID 0x13d3:0x3623 for Qualcomm WCN785xZijun Hu
Add one more part with ID (0x13d3, 0x3623) to usb_device_id table for Qualcomm WCN785x, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3623 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add one more ID 0x0489:0xe0f3 for Qualcomm WCN785xZijun Hu
Add one more part with ID (0x0489, 0xe0f3) to usb_device_id table for Qualcomm WCN785x, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f3 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: add Foxconn 0xe0fc for Qualcomm WCN785xAaron Ma
Firmwares are already in upstream. kernel boot log as following: Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00190200.bin Bluetooth: hci0: QCA: patch rome 0x190200 build 0x5656, firmware rome 0x190200 build 0x43fb Bluetooth: hci0: using NVM file: qca/nvm_usb_00190200.bin Paired BT headphone, output is good. T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0fc Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: mediatek: change the conditions for ISO interfaceChris Lu
Change conditions for Bluetooth driver claiming and releasing usb ISO interface for MediaTek ISO data transmission. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: mediatek: add intf release flow when usb disconnectChris Lu
MediaTek claim an special usb intr interface for ISO data transmission. The interface need to be released before unregistering hci device when usb disconnect. Removing BT usb dongle without properly releasing the interface may cause Kernel panic while unregister hci device. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: mediatek: add callback function in btusb_disconnectChris Lu
Add disconnect callback function in btusb_disconnect which is reserved for vendor specific usage before deregister hci in btusb_disconnect. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: mediatek: move Bluetooth power off command positionChris Lu
Move MediaTek Bluetooth power off command before releasing usb ISO interface. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-10-16Bluetooth: btusb: Fix regression with fake CSR controllers 0a12:0001Luiz Augusto von Dentz
Fake CSR controllers don't seem to handle short-transfer properly which cause command to time out: kernel: usb 1-1: new full-speed USB device number 19 using xhci_hcd kernel: usb 1-1: New USB device found, idVendor=0a12, idProduct=0001, bcdDevice=88.91 kernel: usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 kernel: usb 1-1: Product: BT DONGLE10 ... Bluetooth: hci1: Opcode 0x1004 failed: -110 kernel: Bluetooth: hci1: command 0x1004 tx timeout According to USB Spec 2.0 Section 5.7.3 Interrupt Transfer Packet Size Constraints a interrupt transfer is considered complete when the size is 0 (ZPL) or < wMaxPacketSize: 'When an interrupt transfer involves more data than can fit in one data payload of the currently established maximum size, all data payloads are required to be maximum-sized except for the last data payload, which will contain the remaining data. An interrupt transfer is complete when the endpoint does one of the following: • Has transferred exactly the amount of data expected • Transfers a packet with a payload size less than wMaxPacketSize or transfers a zero-length packet' Link: https://bugzilla.kernel.org/show_bug.cgi?id=219365 Fixes: 7b05933340f4 ("Bluetooth: btusb: Fix not handling ZPL/short-transfer") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-10-16Bluetooth: btusb: Fix not being able to reconnect after suspendLuiz Augusto von Dentz
This partially reverts 81b3e33bb054 ("Bluetooth: btusb: Don't fail external suspend requests") as it introduced a call to hci_suspend_dev that assumes the system-suspend which doesn't work well when just the device is being suspended because wakeup flag is only set for remote devices that can wakeup the system. Reported-by: Rafael J. Wysocki <rafael@kernel.org> Reported-by: Heiner Kallweit <hkallweit1@gmail.com> Reported-by: Kenneth Crudup <kenny@panix.com> Fixes: 610712298b11 ("Bluetooth: btusb: Don't fail external suspend requests") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by: Rafael J. Wysocki <rafael@kernel.org>
2024-10-04Bluetooth: btusb: Don't fail external suspend requestsLuiz Augusto von Dentz
Commit 4e0a1d8b0675 ("Bluetooth: btusb: Don't suspend when there are connections") introduces a check for connections to prevent auto-suspend but that actually ignored the fact the .suspend callback can be called for external suspend requests which Documentation/driver-api/usb/power-management.rst states the following: 'External suspend calls should never be allowed to fail in this way, only autosuspend calls. The driver can tell them apart by applying the :c:func:`PMSG_IS_AUTO` macro to the message argument to the ``suspend`` method; it will return True for internal PM events (autosuspend) and False for external PM events.' In addition to that align system suspend with USB suspend by using hci_suspend_dev since otherwise the stack would be expecting events such as advertising reports which may not be delivered while the transport is suspended. Fixes: 4e0a1d8b0675 ("Bluetooth: btusb: Don't suspend when there are connections") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by: Kiran K <kiran.k@intel.com>
2024-10-02move asm/unaligned.h to linux/unaligned.hAl Viro
asm/unaligned.h is always an include of asm-generic/unaligned.h; might as well move that thing to linux/unaligned.h and include that - there's nothing arch-specific in that header. auto-generated by the following: for i in `git grep -l -w asm/unaligned.h`; do sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i done for i in `git grep -l -w asm-generic/unaligned.h`; do sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i done git mv include/asm-generic/unaligned.h include/linux/unaligned.h git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
2024-09-12Bluetooth: btusb: Fix not handling ZPL/short-transferLuiz Augusto von Dentz
Requesting transfers of the exact same size of wMaxPacketSize may result in ZPL/short-transfer since the USB stack cannot handle it as we are limiting the buffer size to be the same as wMaxPacketSize. Also, in terms of throughput this change has the same effect to interrupt endpoint as 290ba200815f "Bluetooth: Improve USB driver throughput by increasing the frame size" had for the bulk endpoint, so users of the advertisement bearer (e.g. BT Mesh) may benefit from this change. Fixes: 5e23b923da03 ("[Bluetooth] Add generic driver for Bluetooth USB devices") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by: Kiran K <kiran.k@intel.com>
2024-09-12Bluetooth: btusb: Add 2 USB HW IDs for MT7925 (0xe118/e)Michael Burch
Add 2 USB HW IDs for MT7925 (0xe118/e) to ensure proper recognition. These HW IDs are extracted from Windows driver inf file: https://dlcdnets.asus.com/pub/ASUS/nb/Image/Driver/Bluetooth/39389/Bluetooth_DCH_MediaTek_B_V1.1037.0.433Sub2_39389.exe?model=H7606WV Patch has been tested successfully on an Asus ProArt P16 model H7606WV. Controller is recognized devices pair successfully. Signed-off-by: Michael Burch <me@michaelburch.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-09-10Bluetooth: btusb: Add Mediatek MT7925 support ID 0x13d3:0x3608Pavel Nikulin
Add the support ID (0x13d3, 0x3608) to usb_device_id table for Realtek MT7925B14L found on AW-EM637 WiFi+BT modules in 2024 Asus laptops. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3608 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Pavel Nikulin <pavel@noa-labs.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-09-10Bluetooth: btrtl: Add the support for RTL8922AMax Chou
Add the support for RTL8922A BT controller on USB interface. The necessary firmware will be submitted to linux-firmware project. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=8922 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C885A01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-09-10Bluetooth: btusb: Add Realtek RTL8852C support ID 0x0489:0xe122Hilda Wu
Add the support ID (0x0489, 0xe122) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e122 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-09-10Bluetooth: btusb: Invert LE State flag to set invalid rather then validLuiz Augusto von Dentz
This inverts the LE State flag so by default we assume the controllers would report valid states rather than invalid so it is inline with the respective quirk (HCI_QUIRK_BROKEN_LE_STATES). Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-09-10Bluetooth: btusb: Add MediaTek MT7925-B22M support ID 0x13d3:0x3604Alexander Hall
This patch fixes bluetooth support on the MediaTek MT7925 WiFi 7 + BT 5.3 M.2 chipset that I purchased from aliexpress (and which arrived today). The PCB states that it is an MT7925B22M. Device from /sys/kernel/debug/usb/devices: T: Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3604 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us High fidelity images I took of the chip itself for future reference: https://archive.org/details/MediaTek-MT7925B22M/ Webpage the chip was purchased from, note it is different from the images taken: https://web.archive.org/web/20240620021119/https://www.aliexpress. us/item/3256806821207897.html Signed-off-by: Alexander Hall <bearodark@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-08-15Bluetooth: HCI: Invert LE State quirk to be opt-out rather then opt-inLuiz Augusto von Dentz
This inverts the LE State quirk so by default we assume the controllers would report valid states rather than invalid which is how quirks normally behave, also this would result in HCI command failing it the LE States are really broken thus exposing the controllers that are really broken in this respect. Link: https://github.com/bluez/bluez/issues/584 Fixes: 220915857e29 ("Bluetooth: Adding driver and quirk defs for multi-role LE") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btintel: Add support for Whale Peak2Kiran K
from /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0039 Rev= 0.00 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: mediatek: add ISO data transmission functionsChris Lu
This patch implements functions for ISO data send and receive in btusb driver for MediaTek's controller. MediaTek defines a specific interrupt endpoint for ISO data transmissin because the characteristics of interrupt endpoint are similar to the application of ISO data which can support guaranteed transmissin bandwidth, enough maximum data length and error checking mechanism. Driver sets up ISO interface and endpoints in btusb_mtk_setup and clears the setup in btusb_mtk_shutdown. These flow can't move to btmtk.c due to btusb_driver is only defined in btusb.c when claiming/relaesing interface. ISO packet anchor stops when driver suspending and resubmit interrupt urb for ISO data when driver resuming. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btmtk: move btusb_recv_acl_mtk to btmtk.cChris Lu
Move btusb_recv_acl_mtk from btusb.c to btmtk.c which holds vendor specific stuff and would make btusb.c clean. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btmtk: move btusb_mtk_[setup, shutdown] to btmtk.cChris Lu
Move btusb_mtk_[setup, shutdown] and related function from btusb.c to btmtk.c which holds vendor specific stuff and would make btusb.c clean. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.cChris Lu
Move btusb_mtk_hci_wmt_sync from btusb.c to btmtk.c which holds vendor specific stuff and would make btusb.c clean. Add usb.h header to btmtksdio.c/btmtkuart.c for usb related element defined in btmtk.h Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: add callback function in btusb suspend/resumeChris Lu
Add suspend/resum callback function in btusb_data which are reserved for vendor specific usage during suspend/resume. hdev->suspend will be added before stop traffic in btusb_suspend and hdev-> resume will be added after resubmit urb in btusb_resume. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btmtk: rename btmediatek_dataChris Lu
Rename btmediatek_data to have a consistent prefix throughout the driver. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: mediatek: return error for failed reg accessChris Lu
Update the code to immediately return an error code if accessing a related register fails. This ensures that our desired logic for subsequent register operations is maintained and allows us to promptly catch any unexpected errors. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: mediatek: remove the unnecessary goto tagChris Lu
Remove the unnecessary goto tag whether there is an error or not, we have to free the buffer at the end of the function. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x13d3:0x3591WangYuli
Add the support ID(0x13d3, 0x3591) to usb_device_id table for Realtek RTL8852BE. The device table is as follows: T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3591 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Cc: stable@vger.kernel.org Signed-off-by: Wentao Guan <guanwentao@uniontech.com> Signed-off-by: WangYuli <wangyuli@uniontech.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
generated by cgit (git 2.34.1) at 2025-07-15 17:31:12 +0000