summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)Author
2024-07-15Bluetooth: hci_qca: Fix build errorLuiz Augusto von Dentz
This fixes the following build error introduced by b80f4e3b8cb8 ("Bluetooth: hci_qca: schedule a devm action for disabling the clock"): drivers/bluetooth/hci_qca.c: In function ‘qca_serdev_remove’: drivers/bluetooth/hci_qca.c:2501:2: error: label at end of compound statement 2501 | default: | ^~~~~~~ Fixes: b80f4e3b8cb8 ("Bluetooth: hci_qca: schedule a devm action for disabling the clock") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: hci_qca: use the power sequencer for wcn7850 and wcn6855Bartosz Golaszewski
In preparation for using the power sequencing subsystem on sm8650 boards and X13s laptop let's make pwrseq the default for wcn7850 and wcn6855. Both these models require an enable GPIO so we can safely assume that if the property is not there, then we should try to get the power sequencer. Due to how the pwrseq lookup works - checking the provider at run-time - we cannot really do it the other way around as we'd get stuck forever on -EPROBE_DEFER. If the relevant OF node does have the 'enable-gpios' property, we fallback to the existing code for backward compatibility with older DTs. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: hci_qca: make pwrseq calls the default if availableBartosz Golaszewski
If the device has a power sequencing handle, use it first. Otherwise fall back to whatever code already exists. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: hci_qca: unduplicate calls to hci_uart_register_device()Bartosz Golaszewski
Now that all three branches of the switch end up doing the same thing, we can move the call to hci_uart_register_device() past it and unify the error message. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: hci_qca: schedule a devm action for disabling the clockBartosz Golaszewski
In preparation for unduplicating the hci_uart registration code, schedule a devres action for disabling the SUSCLK rather than doing it manually. We cannot really use devm_clk_get_enabled() as we also set the rate before enabling the clock. While this should in theory work, I don't want to risk breaking existing users. One solution for the future is to add devm_clk_get_enabled_with_rate() to the clock framework. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btnxpuart: Fix warnings for suspend and resume functionsNeeraj Sanjay Kale
This fixes the warnings 'nxp_serdev_resume' and 'nxp_serdev_suspend' defined but not used. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202407100518.06Xxq5PK-lkp@intel.com/ Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btnxpuart: Add system suspend and resume handlersNeeraj Sanjay Kale
This adds handling for system suspend and resume. While the host enters suspend state, the driver will drive the chip into low power state. Similarly when system is resuming, the driver will wake up the chip. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btnxpuart: Add support for IW615 chipsetNeeraj Sanjay Kale
This adds support for IW615 chipset with it's bootloader signature and firmware file. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btnxpuart: Add support for AW693 A1 chipsetNeeraj Sanjay Kale
This adds support for AW693 A1 chipset with it's bootloader signature and firmware file. No firmware name change needed for AW693 A0 chipset. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btintel: Add support for Whale Peak2Kiran K
from /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0039 Rev= 0.00 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btintel: Add support for BlazarU coreKiran K
Add support for BlazarU core (CNVi). Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: mediatek: add ISO data transmission functionsChris Lu
This patch implements functions for ISO data send and receive in btusb driver for MediaTek's controller. MediaTek defines a specific interrupt endpoint for ISO data transmissin because the characteristics of interrupt endpoint are similar to the application of ISO data which can support guaranteed transmissin bandwidth, enough maximum data length and error checking mechanism. Driver sets up ISO interface and endpoints in btusb_mtk_setup and clears the setup in btusb_mtk_shutdown. These flow can't move to btmtk.c due to btusb_driver is only defined in btusb.c when claiming/relaesing interface. ISO packet anchor stops when driver suspending and resubmit interrupt urb for ISO data when driver resuming. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btmtk: move btusb_recv_acl_mtk to btmtk.cChris Lu
Move btusb_recv_acl_mtk from btusb.c to btmtk.c which holds vendor specific stuff and would make btusb.c clean. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btmtk: move btusb_mtk_[setup, shutdown] to btmtk.cChris Lu
Move btusb_mtk_[setup, shutdown] and related function from btusb.c to btmtk.c which holds vendor specific stuff and would make btusb.c clean. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.cChris Lu
Move btusb_mtk_hci_wmt_sync from btusb.c to btmtk.c which holds vendor specific stuff and would make btusb.c clean. Add usb.h header to btmtksdio.c/btmtkuart.c for usb related element defined in btmtk.h Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: add callback function in btusb suspend/resumeChris Lu
Add suspend/resum callback function in btusb_data which are reserved for vendor specific usage during suspend/resume. hdev->suspend will be added before stop traffic in btusb_suspend and hdev-> resume will be added after resubmit urb in btusb_resume. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btmtk: rename btmediatek_dataChris Lu
Rename btmediatek_data to have a consistent prefix throughout the driver. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: mediatek: return error for failed reg accessChris Lu
Update the code to immediately return an error code if accessing a related register fails. This ensures that our desired logic for subsequent register operations is maintained and allows us to promptly catch any unexpected errors. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: mediatek: remove the unnecessary goto tagChris Lu
Remove the unnecessary goto tag whether there is an error or not, we have to free the buffer at the end of the function. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x13d3:0x3591WangYuli
Add the support ID(0x13d3, 0x3591) to usb_device_id table for Realtek RTL8852BE. The device table is as follows: T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3591 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Cc: stable@vger.kernel.org Signed-off-by: Wentao Guan <guanwentao@uniontech.com> Signed-off-by: WangYuli <wangyuli@uniontech.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btintel: Fix the sfi name for BlazarUKiran K
Use INTEL_HW_VARIANT() instead of CNVi Id to decide to load Intermediate Loader (IML) image. Fix the driver loading incorrect firmware for BlazarU product. dmesg: ..... [146.111834] Bluetooth: hci0: Minimum firmware build 1 week 10 2014 [146.111839] Bluetooth: hci0: Bootloader timestamp 2022.18 buildtype 1 build 16362 [146.111848] Bluetooth: hci0: No support for _PRR ACPI method [146.112204] Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-0291-0291-iml.sfi (-2) Fixes: 164c62f958f8 ("Bluetooth: btintel: Add firmware ID to firmware name") Reported-by: Tsigan, Vladislav <vladislav.tsigan@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: qca: don't disable power management for QCA6390Bartosz Golaszewski
We unnecessarily fallthrough the case for QCA6390 when initializing the device and hit the condition where - due to the lack of the enable-gpio - we disable power management despite using the power sequencer. We don't need to look for clocks on this model so it makes more sense to just register the hci device and break the switch. Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Fixes: 9a15ce685706 ("Bluetooth: qca: use the power sequencer for QCA6390") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # RB5 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: hci: fix build when POWER_SEQUENCING=mKrzysztof Kozlowski
BT_HCIUART_QCA, which is a bool and an HCI UART component, uses now power sequencing, so we need to be sure BT_HCIUART_QCA=y and POWER_SEQUENCING=m cannot happen: /usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_serdev_probe': drivers/bluetooth/hci_qca.c:2401:(.text+0xc48): undefined reference to `devm_pwrseq_get' /usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_power_shutdown': drivers/bluetooth/hci_qca.c:2192:(.text+0x29e8): undefined reference to `pwrseq_power_off' /usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_power_on': drivers/bluetooth/hci_qca.c:1808:(.text+0x3390): undefined reference to `pwrseq_power_on' Fixes: 9a15ce685706 ("Bluetooth: qca: use the power sequencer for QCA6390") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: btintel: Fix spelling of *intermediate* in commentPaul Menzel
Fixes: f3b845e0aea3 ("Bluetooth: btintel: Add support to download intermediate loader") Cc: Kiran K <kiran.k@intel.com> Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-15Bluetooth: qca: use the power sequencer for QCA6390Bartosz Golaszewski
Use the pwrseq subsystem's consumer API to run the power-up sequence for the Bluetooth module of the QCA6390 package. Tested-by: Amit Pundir <amit.pundir@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD, SM8650-QRD & SM8650-HDK Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # OnePlus 8T Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btintel: Add firmware ID to firmware nameKiran K
From BlazarI onwards, driver shall append the firmware ID (usually represents transport type) while constructing the firmware name. Firmware ID is returned on Intel Read Version command. The new firmware file name for operational image and ddc file shall be, ibt-<cnvi_top type+cnvi_top step>-<cnvr_top type+cnvr_top step-fw_id>.[sfi|ddc] dmesg snippet from BlazarI pcie product: ...... [17.098858] Bluetooth: hci0: Found device firmware: intel/ibt-0190-0291-pci.sfi [17.098871] Bluetooth: hci0: Boot Address: 0x10000800 [17.098872] Bluetooth: hci0: Firmware Version: 214-25.24 [17.158229] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [17.158236] Bluetooth: BNEP filters: protocol multicast [17.158241] Bluetooth: BNEP socket layer initialized [17.468789] Bluetooth: hci0: Waiting for firmware download to complete [17.468793] Bluetooth: hci0: Firmware loaded in 361262 usecs [17.468872] Bluetooth: hci0: Waiting for device to boot [17.504148] Bluetooth: hci0: Device booted in 34512 usecs [17.504148] Bluetooth: hci0: Malformed MSFT vendor event: 0x02 [17.504682] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0190-0291-pci.ddc [17.505380] Bluetooth: hci0: Applying Intel DDC parameters completed [17.505622] Bluetooth: hci0: Firmware timestamp 2024.25 buildtype 3 build 64726 [17.505624] Bluetooth: hci0: Firmware SHA1: 0x9f4adddc [17.505838] Bluetooth: hci0: Fseq status: Success (0x00) [17.505839] Bluetooth: hci0: Fseq executed: 00.00.04.183 [17.505840] Bluetooth: hci0: Fseq BT Top: 00.00.04.183 dmesg snippet from BlazarI usb product: ....... [14.212072] Bluetooth: hci0: Found device firmware: intel/ibt-0190-0291-usb.sfi [14.212091] Bluetooth: hci0: Boot Address: 0x10000800 [14.212093] Bluetooth: hci0: Firmware Version: 79-21.24 [14.262125] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [14.262129] Bluetooth: BNEP filters: protocol multicast [14.262133] Bluetooth: BNEP socket layer initialized [15.865421] Bluetooth: hci0: Waiting for firmware download to complete [15.865991] Bluetooth: hci0: Firmware loaded in 1615150 usecs [15.866017] Bluetooth: hci0: Waiting for device to boot [15.899934] Bluetooth: hci0: Malformed MSFT vendor event: 0x02 [15.899942] Bluetooth: hci0: Device booted in 33139 usecs [15.900172] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0190-0291-usb.ddc [15.901928] Bluetooth: hci0: Applying Intel DDC parameters completed [15.904993] Bluetooth: hci0: Firmware timestamp 2024.21 buildtype 3 build 63311 [15.904996] Bluetooth: hci0: Firmware SHA1: 0x8b217cf7 [15.908929] Bluetooth: hci0: Fseq status: Success (0x00) [15.908934] Bluetooth: hci0: Fseq executed: 00.00.04.180 [15.908935] Bluetooth: hci0: Fseq BT Top: 00.00.04.180 Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btusb: Add RTL8852BE device 0489:e125 to device tablesHilda Wu
Add the support ID 0489:e125 to usb_device_id table for Realtek RTL8852B chip. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e125 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btnxpuart: Add handling for boot-signature timeout errorsNeeraj Sanjay Kale
This handles the timeout error codes sent by the chip as part of the bootloader signatures during firmware download process. When the bootloader does not receive a response packet from the host within a specific time, it adds an error code to the bootloader signature while requesting for the FW chunk from the same offset. The host is expected to clear this error code with a NAK, and reply to only those bootloader signatures which have error code 0. However, the driver was ignoring this error code and replying with the firmware chunks instead, which is apparently ignored by the chip and the chip resends the same bootloader signature with the error code again. This happens in a loop until the error code self clears and firmware download proceeds ahead, adding a couple of milliseconds to the total firmware download time. Commit 689ca16e5232 was an initial implementation which simply printed the following line during driver debug: - FW Download received err 0x04 from chip This commit adds the expected handling to the error codes. This error handling is valid for data_req bootloader signatures for V3 and future bootloader versions. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Fixes: 689ca16e5232 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btnxpuart: Update firmware namesNeeraj Sanjay Kale
This updates the firmware names of 3 chipsets: w8987, w8997, w9098. These changes are been done to standardize chip specific firmware file names to be in sync with firmware names of newer chipsets. The naming convention for BT-only files would be as follows: For dual-radio WiFi+BT chipsets: - <protocol-BT><chip-name>_bt_v<HW-version>.bin For tri-radio WiFi+BT+15.4 chipsets: - <protocol-BT><protocol-15.4><chip-name>_bt_v<HW-version>.bin To maintain backward compatibility, this commit adds a provision to request older firmware file name, if new firmware file name not found in /lib/firmware/nxp/. A new device tree property has been introduced called firmware-name, to override the hardcoded firmware names (old and new) in the driver. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: hci_bcm4377: Add BCM4388 supportHector Martin
This new variant needs a different core2_window1 and always uses beamforming. The BAR2 also has an offset (RAM start, presumably), so add that. Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Sven Peter <sven@svenpeter.dev> [sven: rebased, updated some comments, mentioned 4388 in Kconfig] Signed-off-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: Add vendor-specific packet classification for ISO dataYing Hsu
When HCI raw sockets are opened, the Bluetooth kernel module doesn't track CIS/BIS connections. User-space applications have to identify ISO data by maintaining connection information and look up the mapping for each ACL data packet received. Besides, btsnoop log captured in kernel couldn't tell ISO data from ACL data in this case. To avoid additional lookups, this patch introduces vendor-specific packet classification for Intel BT controllers to distinguish ISO data packets from ACL data packets. Signed-off-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btintel_pcie: Remove unnecessary memset(0) callsThorsten Blum
Remove memset(0) after dma_alloc_coherent(), which already zeroes out the memory, and fix the following two Coccinelle/coccicheck warnings reported by zalloc-simple.cocci: btintel_pcie.c:837:19-37: WARNING: dma_alloc_coherent used in /* Allocate full chunk of data buffer for DMA first and do indexing and * initialization next, so it can be freed easily */ rxq->buf_v_addr already zeroes out memory, so memset is not needed btintel_pcie.c:792:19-37: WARNING: dma_alloc_coherent used in /* Allocate full chunk of data buffer for DMA first and do indexing and * initialization next, so it can be freed easily */ txq->buf_v_addr already zeroes out memory, so memset is not needed Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: Use sizeof(*pointer) instead of sizeof(type)Erick Archer
It is preferred to use sizeof(*pointer) instead of sizeof(type) due to the type of the variable can change and one needs not change the former (unlike the latter). This patch has no effect on runtime behavior. Signed-off-by: Erick Archer <erick.archer@outlook.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth/nokia: Remove unused struct 'hci_nokia_radio_hdr'Dr. David Alan Gilbert
'hci_nokia_radio_hdr' looks like it was unused since it's initial commit. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btintel_pcie: Fix irq leakKiran K
Free irq before releasing irq vector. Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btintel_pcie: Print Firmware Sequencer informationKiran K
Firmware sequencer (FSEQ) is a common code shared across Bluetooth and Wifi. Printing FSEQ will help to debug if there is any mismatch between Bluetooth and Wifi FSEQ. Make 'btintel_print_fseq_info' public and use it in btintel_pcie.c. dmesg: .... [ 5335.695740] Bluetooth: hci0: Device booted in 33872 usecs [ 5335.695918] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0190-0291.ddc [ 5335.697011] Bluetooth: hci0: Applying Intel DDC parameters completed [ 5335.697837] Bluetooth: hci0: Firmware timestamp 2024.20 buildtype 0 build 62871 [ 5335.697848] Bluetooth: hci0: Firmware SHA1: 0xeffdce06 [ 5335.698655] Bluetooth: hci0: Fseq status: Success (0x00) [ 5335.698666] Bluetooth: hci0: Fseq executed: 00.00.04.176 [ 5335.698670] Bluetooth: hci0: Fseq BT Top: 00.00.04.176 [ 5335.750204] Bluetooth: MGMT ver 1.22 Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btusb: mediatek: add MT7922 subsystem resetHao Qin
Add the support of MT7922 bluetooth subsystem reset that was called the auto revert to self-recover from the fatal error in the controller like the host encounters HCI cmd timeout or the controller crashes. Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Hao Qin <hao.qin@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btusb: mediatek: reset the controller before downloading the fwHao Qin
Reset the controller before downloading the firmware to improve its reliability. This includes situations like cold or warm reboots, ensuring the controller is in its initial state before starting the firmware download. Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Co-developed-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Hao Qin <hao.qin@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btusb: mediatek: refactor the function btusb_mtk_resetHao Qin
Extract the function btusb_mtk_subsys_reset from the btusb_mtk_reset for the future handling of resetting bluetooth controller without the USB reset. Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Hao Qin <hao.qin@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btmtk: apply the common btmtk_fw_get_filenameSean Wang
Apply the common btmtk_fw_get_filename to avoid the similar coding in each driver. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btmtk: add the function to get the fw nameSean Wang
Include a shared function to get the firmware name, to prevent repeating code for similar chipsets. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btintel: Refactor btintel_set_ppag()Kiran K
Current flow iterates the ACPI table associated with Bluetooth controller looking for PPAG method. Method name can be directly passed to acpi_evaluate_object function instead of iterating the table. Fixes: c585a92b2f9c ("Bluetooth: btintel: Set Per Platform Antenna Gain(PPAG)") Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btnxpuart: Shutdown timer and prevent rearming when driver unloadingLuke Wang
When unload the btnxpuart driver, its associated timer will be deleted. If the timer happens to be modified at this moment, it leads to the kernel call this timer even after the driver unloaded, resulting in kernel panic. Use timer_shutdown_sync() instead of del_timer_sync() to prevent rearming. panic log: Internal error: Oops: 0000000086000007 [#1] PREEMPT SMP Modules linked in: algif_hash algif_skcipher af_alg moal(O) mlan(O) crct10dif_ce polyval_ce polyval_generic snd_soc_imx_card snd_soc_fsl_asoc_card snd_soc_imx_audmux mxc_jpeg_encdec v4l2_jpeg snd_soc_wm8962 snd_soc_fsl_micfil snd_soc_fsl_sai flexcan snd_soc_fsl_utils ap130x rpmsg_ctrl imx_pcm_dma can_dev rpmsg_char pwm_fan fuse [last unloaded: btnxpuart] CPU: 5 PID: 723 Comm: memtester Tainted: G O 6.6.23-lts-next-06207-g4aef2658ac28 #1 Hardware name: NXP i.MX95 19X19 board (DT) pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : 0xffff80007a2cf464 lr : call_timer_fn.isra.0+0x24/0x80 ... Call trace: 0xffff80007a2cf464 __run_timers+0x234/0x280 run_timer_softirq+0x20/0x40 __do_softirq+0x100/0x26c ____do_softirq+0x10/0x1c call_on_irq_stack+0x24/0x4c do_softirq_own_stack+0x1c/0x2c irq_exit_rcu+0xc0/0xdc el0_interrupt+0x54/0xd8 __el0_irq_handler_common+0x18/0x24 el0t_64_irq_handler+0x10/0x1c el0t_64_irq+0x190/0x194 Code: ???????? ???????? ???????? ???????? (????????) ---[ end trace 0000000000000000 ]--- Kernel panic - not syncing: Oops: Fatal exception in interrupt SMP: stopping secondary CPUs Kernel Offset: disabled CPU features: 0x0,c0000000,40028143,1000721b Memory Limit: none ---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]--- Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btnxpuart: Handle FW Download Abort scenarioNeeraj Sanjay Kale
This adds a new flag BTNXPUART_FW_DOWNLOAD_ABORT which handles the situation where driver is removed while firmware download is in progress. logs: modprobe btnxpuart [65239.230431] Bluetooth: hci0: ChipID: 7601, Version: 0 [65239.236670] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se rmmod btnxpuart [65241.425300] Bluetooth: hci0: FW Download Aborted Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by: Guillaume Legoupil <guillaume.legoupil@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btnxpuart: Enable status prints for firmware downloadNeeraj Sanjay Kale
This enables prints for firmware download which can help automation tests to verify firmware download functionality. dmesg logs before: modprobe btnxpuart [ 1999.187264] Bluetooth: MGMT ver 1.22 dmesg logs with this patch: modprobe btnxpuart [16179.758515] Bluetooth: hci0: ChipID: 7601, Version: 0 [16179.764748] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se [16181.217490] Bluetooth: hci0: FW Download Complete: 372696 bytes [16182.701398] Bluetooth: MGMT ver 1.22 Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by: Guillaume Legoupil <guillaume.legoupil@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: btnxpuart: Fix Null pointer dereference in btnxpuart_flush()Neeraj Sanjay Kale
This adds a check before freeing the rx->skb in flush and close functions to handle the kernel crash seen while removing driver after FW download fails or before FW download completes. dmesg log: [ 54.634586] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000080 [ 54.643398] Mem abort info: [ 54.646204] ESR = 0x0000000096000004 [ 54.649964] EC = 0x25: DABT (current EL), IL = 32 bits [ 54.655286] SET = 0, FnV = 0 [ 54.658348] EA = 0, S1PTW = 0 [ 54.661498] FSC = 0x04: level 0 translation fault [ 54.666391] Data abort info: [ 54.669273] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 54.674768] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 54.674771] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 54.674775] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000048860000 [ 54.674780] [0000000000000080] pgd=0000000000000000, p4d=0000000000000000 [ 54.703880] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [ 54.710152] Modules linked in: btnxpuart(-) overlay fsl_jr_uio caam_jr caamkeyblob_desc caamhash_desc caamalg_desc crypto_engine authenc libdes crct10dif_ce polyval_ce polyval_generic snd_soc_imx_spdif snd_soc_imx_card snd_soc_ak5558 snd_soc_ak4458 caam secvio error snd_soc_fsl_micfil snd_soc_fsl_spdif snd_soc_fsl_sai snd_soc_fsl_utils imx_pcm_dma gpio_ir_recv rc_core sch_fq_codel fuse [ 54.744357] CPU: 3 PID: 72 Comm: kworker/u9:0 Not tainted 6.6.3-otbr-g128004619037 #2 [ 54.744364] Hardware name: FSL i.MX8MM EVK board (DT) [ 54.744368] Workqueue: hci0 hci_power_on [ 54.757244] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 54.757249] pc : kfree_skb_reason+0x18/0xb0 [ 54.772299] lr : btnxpuart_flush+0x40/0x58 [btnxpuart] [ 54.782921] sp : ffff8000805ebca0 [ 54.782923] x29: ffff8000805ebca0 x28: ffffa5c6cf1869c0 x27: ffffa5c6cf186000 [ 54.782931] x26: ffff377b84852400 x25: ffff377b848523c0 x24: ffff377b845e7230 [ 54.782938] x23: ffffa5c6ce8dbe08 x22: ffffa5c6ceb65410 x21: 00000000ffffff92 [ 54.782945] x20: ffffa5c6ce8dbe98 x19: ffffffffffffffac x18: ffffffffffffffff [ 54.807651] x17: 0000000000000000 x16: ffffa5c6ce2824ec x15: ffff8001005eb857 [ 54.821917] x14: 0000000000000000 x13: ffffa5c6cf1a02e0 x12: 0000000000000642 [ 54.821924] x11: 0000000000000040 x10: ffffa5c6cf19d690 x9 : ffffa5c6cf19d688 [ 54.821931] x8 : ffff377b86000028 x7 : 0000000000000000 x6 : 0000000000000000 [ 54.821938] x5 : ffff377b86000000 x4 : 0000000000000000 x3 : 0000000000000000 [ 54.843331] x2 : 0000000000000000 x1 : 0000000000000002 x0 : ffffffffffffffac [ 54.857599] Call trace: [ 54.857601] kfree_skb_reason+0x18/0xb0 [ 54.863878] btnxpuart_flush+0x40/0x58 [btnxpuart] [ 54.863888] hci_dev_open_sync+0x3a8/0xa04 [ 54.872773] hci_power_on+0x54/0x2e4 [ 54.881832] process_one_work+0x138/0x260 [ 54.881842] worker_thread+0x32c/0x438 [ 54.881847] kthread+0x118/0x11c [ 54.881853] ret_from_fork+0x10/0x20 [ 54.896406] Code: a9be7bfd 910003fd f9000bf3 aa0003f3 (b940d400) [ 54.896410] ---[ end trace 0000000000000000 ]--- Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by: Guillaume Legoupil <guillaume.legoupil@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: hci_bcm4377: Increase boot timeoutHector Martin
BCM4388 takes over 2 seconds to boot, so increase the timeout. Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-07-14Bluetooth: hci_bcm4377: Use correct unit for timeoutsSven Peter
BCM4377_TIMEOUT is always used to wait for completitions and their API expects a timeout in jiffies instead of msecs. Fixes: 8a06127602de ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards") Signed-off-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-06-28Bluetooth: btnxpuart: Enable Power Save feature on startupNeeraj Sanjay Kale
This sets the default power save mode setting to enabled. The power save feature is now stable and stress test issues, such as the TX timeout error, have been resolved. commit c7ee0bc8db32 ("Bluetooth: btnxpuart: Resolve TX timeout error in power save stress test") With this setting, the driver will send the vendor command to FW at startup, to enable power save feature. User can disable this feature using the following vendor command: hcitool cmd 3f 23 03 00 00 (HCI_NXP_AUTO_SLEEP_MODE) Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-06-28Bluetooth: qca: Fix BT enable failure again for QCA6390 after warm rebootZijun Hu
Commit 272970be3dab ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev") will cause below regression issue: BT can't be enabled after below steps: cold boot -> enable BT -> disable BT -> warm reboot -> BT enable failure if property enable-gpios is not configured within DT|ACPI for QCA6390. The commit is to fix a use-after-free issue within qca_serdev_shutdown() by adding condition to avoid the serdev is flushed or wrote after closed but also introduces this regression issue regarding above steps since the VSC is not sent to reset controller during warm reboot. Fixed by sending the VSC to reset controller within qca_serdev_shutdown() once BT was ever enabled, and the use-after-free issue is also fixed by this change since the serdev is still opened before it is flushed or wrote. Verified by the reported machine Dell XPS 13 9310 laptop over below two kernel commits: commit e00fc2700a3f ("Bluetooth: btusb: Fix triggering coredump implementation for QCA") of bluetooth-next tree. commit b23d98d46d28 ("Bluetooth: btusb: Fix triggering coredump implementation for QCA") of linus mainline tree. Fixes: 272970be3dab ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev") Cc: stable@vger.kernel.org Reported-by: Wren Turkal <wt@penguintechs.org> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218726 Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Tested-by: Wren Turkal <wt@penguintechs.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
generated by cgit (git 2.34.1) at 2025-07-16 09:40:26 +0000