| Age | Commit message (Collapse) | Author |
|---|
|
The OF match table is not NULL-terminated.
Fix this by adding a sentinel to nmk_i2c_eyeq_match_table[].
Fixes: a0d15cc47f29be6d ("i2c: nomadik: switch from of_device_is_compatible() to of_match_device()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
- BRCR value must go into the BRCR1 field when in high-speed mode.
It goes into BRCR2 otherwise.
- Remove fallback to standard mode if priv->sm > I2C_FREQ_MODE_FAST.
- Set SM properly in probe; previously it only checked STANDARD versus
FAST. Now we set STANDARD, FAST, FAST_PLUS or HIGH_SPEED.
- Remove all comment sections saying we only support low-speeds.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Current BRCR computation is:
brcr = floor(i2cclk / (clkfreq * div))
With brcr: "baud rate counter", an internal clock divider,
and i2cclk: input clock rate (24MHz, 38.4MHz or 48MHz),
and clkfreq: desired bus rate,
and div: speed-mode dependent divider (2 for standard, 3 otherwise).
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) = 4
and resulting bus rate = 48MHz / (4 * 3) = 4MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) = 12
and resulting bus rate = 38.4MHz / (12 * 3) = 1066kHz
The current computation means we always pick the smallest divider that
gives a bus rate above target. We should instead pick the largest
divider that gives a bus rate below target, using:
brcr = floor(i2cclk / (clkfreq * div)) + 1
If we redo the above examples:
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) + 1 = 5
and resulting bus rate = 48MHz / (5 * 3) = 3.2MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) + 1 = 13
and resulting bus rate = 38.4MHz / (13 * 3) = 985kHz
In kernel C code, floor(x) is DIV_ROUND_DOWN() and,
floor(x)+1 is DIV_ROUND_UP().
This is much less of an issue with slower bus rates (ie those currently
supported), because the gap from one divider to the next is much
smaller. It however keeps us from always using bus rates superior to
the target.
This fix is required for later on supporting faster bus rates:
I2C_FREQ_MODE_FAST_PLUS (1MHz) and I2C_FREQ_MODE_HIGH_SPEED (3.4MHz).
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add EyeQ6H support to the nmk-i2c AMBA driver. It shares the same quirk
as EyeQ5: the memory bus only supports 32-bit accesses. Avoid writeb()
and readb() by reusing the same `priv->has_32b_bus` flag.
It does NOT need to write speed-mode specific value into a register;
therefore it does not depend on the mobileye,olb DT property.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Compatible-specific behavior is implemented using a if-condition on the
return value from of_device_is_compatible(), from probe. It does not
scale well when compatible number increases. Switch to using a match
table and a call to of_match_device().
We DO NOT attach a .of_match_table field to our amba driver, as we do
not use the table to match our driver to devices.
Sort probe variable declarations in reverse christmas tree to try and
introduce some logic into the ordering.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"i2c core removes an argument from the i2c_mux_add_adapter() call to
further deprecate class based I2C device instantiation. All users are
converted, too.
Other that that, Andi collected a number if I2C host driver patches.
Those merges have their own description"
* tag 'i2c-for-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (72 commits)
power: supply: sbs-manager: Remove class argument from i2c_mux_add_adapter()
i2c: mux: Remove class argument from i2c_mux_add_adapter()
i2c: synquacer: Fix an error handling path in synquacer_i2c_probe()
i2c: acpi: Unbind mux adapters before delete
i2c: designware: Replace MODULE_ALIAS() with MODULE_DEVICE_TABLE()
i2c: pxa: use 'time_left' variable with wait_event_timeout()
i2c: s3c2410: use 'time_left' variable with wait_event_timeout()
i2c: rk3x: use 'time_left' variable with wait_event_timeout()
i2c: qcom-geni: use 'time_left' variable with wait_for_completion_timeout()
i2c: jz4780: use 'time_left' variable with wait_for_completion_timeout()
i2c: synquacer: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f7: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f4: use 'time_left' variable with wait_for_completion_timeout()
i2c: st: use 'time_left' variable with wait_for_completion_timeout()
i2c: omap: use 'time_left' variable with wait_for_completion_timeout()
i2c: imx-lpi2c: use 'time_left' variable with wait_for_completion_timeout()
i2c: hix5hd2: use 'time_left' variable with wait_for_completion_timeout()
i2c: exynos5: use 'time_left' variable with wait_for_completion_timeout()
i2c: digicolor: use 'time_left' variable with wait_for_completion_timeout()
i2c: amd-mp2-plat: use 'time_left' variable with wait_for_completion_timeout()
...
|
|
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Amba bus core already sets owner, so driver does not need to.
Link: https://lore.kernel.org/r/20240326-module-owner-amba-v1-14-4517b091385b@linaro.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Sort #include statements in i2c-nomadik driver.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add compatible for the integration of the same DB8500 IP block into the
Mobileye EyeQ5 platform. Two quirks are present:
- The memory bus only supports 32-bit accesses. Avoid writeb() and
readb() by introducing helper functions that fallback to writel()
and readl().
- A register must be configured for the I2C speed mode; it is located
in a shared register region called OLB. We access that memory region
using a syscon & regmap that gets passed as a phandle (mobileye,olb).
A two-bit enum per controller is written into the register; that
requires us to know the global index of the I2C controller (cell arg
to the mobileye,olb phandle).
We add #include <linux/mfd/syscon.h> and <linux/regmap.h>.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Allow overriding the default timeout value (200ms) from devicetree,
using the generic i2c-transfer-timeout-us property.
The i2c_adapter->timeout field is an unaccurate jiffies amount;
i2c-nomadik uses hrtimers for timeouts below one jiffy.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The FIFO flush function uses a jiffies amount to detect timeouts as the
flushing is async. Replace with ktime to get more accurate precision
and support short timeouts.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Replace the completion by a waitqueue for synchronization from IRQ
handler to task. For short timeouts, use hrtimers, else use timers.
Usecase: avoid blocking the I2C bus for too long when an issue occurs.
The threshold picked is one jiffy: if timeout is below that, use
hrtimers. This threshold is NOT configurable.
Implement behavior but do NOT change fetching of timeout. This means the
timeout is unchanged (200ms) and the hrtimer case will never trigger.
A waitqueue is used because it supports both desired timeout approaches.
See wait_event_timeout() and wait_event_hrtimeout(). An atomic boolean
serves as synchronization condition.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Constant register bit fields are declared using hardcoded hex values;
replace them by calls to BIT() and GENMASK(). Replace custom GEN_MASK()
macro by the generic FIELD_PREP(). Replace manual bit manipulations by
the generic FIELD_GET() macro.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
IRQ_MASK and I2C_CLEAR_ALL_INTS both mask available interrupts. IRQ_MASK
removes top options (bits 29-31). I2C_CLEAR_ALL_INTS removes reserved
options including top bits. Keep the latter.
31 29 27 25 23 21 19 17 15 13 11 09 07 05 03 01
30 28 26 24 22 20 18 16 14 12 10 08 06 04 02 00
-- IRQ_MASK: ---------------------------------------------------
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0
-- I2C_CLEAR_ALL_INTS: -----------------------------------------
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Notice I2C_CLEAR_ALL_INTS is more restrictive than IRQ_MASK.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Disambiguate the usage of dev as a variable name; it is usually best to
keep it reserved for struct device pointers. Avoid having multiple
names for the same struct pointer (previously: dev, nmk, nmk_i2c).
Fix whitespace code style; return indented twice, spacing besides infix
operators, align function call arguments to opening parenthesis. Remove
useless cast to unused return value from init_hw(). Introduce local dev
variable in probe() to alias &adev->dev.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use the new PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230722115046.27323-14-paul@crapouillou.net
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Since commit 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba
driver"), there is no more request_mem_region() call in this driver.
So remove the release_mem_region() call from the remove function which is
likely a left over.
Fixes: 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba driver")
Cc: <stable@vger.kernel.org> # v3.6+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Make use of dev_err_probe() in order to simplify the code and
avoid printing when returning EPROBE_DEFER.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The err_no_mem goto label doesn't do anything. Remove it.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding
size determination a bit safer according to the Linux coding style
convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
These issues were detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/i2c/busses/i2c-nomadik.c:184: warning: Function parameter or member 'timeout' not described in 'nmk_i2c_dev'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Fix the following checkpatch errors:
ERROR: space prohibited before that ',' (ctx:WxW)
#280: FILE: drivers/i2c/busses/i2c-nomadik.c:280:
+ i2c_clr_bit(dev->virtbase + I2C_CR , I2C_CR_PE);
^
ERROR: space prohibited before that ',' (ctx:WxW)
#528: FILE: drivers/i2c/busses/i2c-nomadik.c:528:
+ i2c_set_bit(dev->virtbase + I2C_CR , I2C_CR_PE);
^
No functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
Modules with multiple authors should use multiple MODULE_AUTHOR()
statements according to comment in include/linux/module.h.
Split the i2c modules with multiple authors to use multiple
MODULE_AUTHOR() statements.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Since we have generic definitions for bus frequencies, let's use them.
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Robert Richter <rrichter@marvell.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Elie Morisse <syniurge@gmail.com>
Acked-by: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"res" can't be NULL because it's a pointer to somewhere in the middle of
the "adev" struct. Also probe() succeeded so there is no need to check
here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
These days, the I2C core ensures that the embedded adapter device
ignores the PM states of its children already. Because the adapter
device is an opaque logical device, there is no need for drivers to
repeat that again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
return type of read_i2c() is int not u32. As the assignments to status
are consistent with int here its type is changed to int.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
return type of wait_for_completion_timeout is unsigned long not int. as
timeout is used for wait_for_completion_timeout exclusively here its
type is simply changed to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
While we are here, remove the indentation for the array setup because
such things always break after some time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.
For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.
Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
devm_ioremap() returns NULL on error, not an error.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We should never be busy performing transfers at suspend late, thus
there are no reason to check for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
At system suspend_late, runtime PM has been disabled by the PM core
which means we can safely operate on these resources. Consequentially
we no longer have to wait until the noirq phase of the system suspend.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since the runtime PM state is expected to be active according to the
amba bus, we must align our behaviour while probing to it.
Moreover, this is needed to be able to have the driver fully functional
without depending on CONFIG_RUNTIME_PM.
Since the device is active while a successful probe has been completed,
the reference counting for the clock will be screwed up and never reach
zero. We resolve this by implementing runtime PM callbacks and let them
handle the resources accordingly, including the clock.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[wsa: s/#if/#ifdef/]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The amba bus are responsible for pm_runtime_enable|disable, remove the
redundant pm_runtime_disable at driver removal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use devm_* functions to simplify code and error handling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Move the former platform data struct nmk_i2c_controller into the
per-device state container struct i2c_nmk_client, and remove all
the platform data probe path hacks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[wsa: use 100kHz as default]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Nomadik I2C is now configured from the device tree on all platforms
using this controller. Delete the platform data header and move the
definitions into the driver so it is all contained in one single file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Nomadik I2C controller needs to have the slave set-up time
configured based off the clock used to drive the I2C bus block.
Currently this is done with static assignments assuming that the
block is clocked 48MHz which is pretty likely to be bug-prone.
Calculate the SLSU from the equation given in the datasheet
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
