| Age | Commit message (Collapse) | Author |
|---|
|
Currently, the RIIC driver may run the I2C bus faster than requested,
which may cause subtle failures. E.g. Biju reported a measured bus
speed of 450 kHz instead of the expected maximum of 400 kHz on RZ/G2L.
The initial calculation of the bus period uses DIV_ROUND_UP(), to make
sure the actual bus speed never becomes faster than the requested bus
speed. However, the subsequent division-by-two steps do not use
round-up, which may lead to a too-small period, hence a too-fast and
possible out-of-spec bus speed. E.g. on RZ/Five, requesting a bus speed
of 100 resp. 400 kHz will yield too-fast target bus speeds of 100806
resp. 403226 Hz instead of 97656 resp. 390625 Hz.
Fix this by using DIV_ROUND_UP() in the subsequent divisions, too.
Tested on RZ/A1H, RZ/A2M, and RZ/Five.
Fixes: d982d66514192cdb ("i2c: riic: remove clock and frequency restrictions")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://lore.kernel.org/r/c59aea77998dfea1b4456c4b33b55ab216fcbf5e.1732284746.git.geert+renesas@glider.be
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/i2c to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Simplify checking for unsupported bus speeds and reporting errors by
factoring out the calculation of the maximum bus speed, and by using the
dev_err_probe() helper.
While at it, use "%u" for u32, and improve the error message.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Fast mode plus is available on most of the IP variants that RIIC driver
is working with. The exception is (according to HW manuals of the SoCs
where this IP is available) the Renesas RZ/A1H. For this, patch
introduces the struct riic_of_data::fast_mode_plus.
Fast mode plus was tested on RZ/G3S, RZ/G2{L,UL,LC}, RZ/Five by
instantiating the RIIC frequency to 1MHz and issuing i2c reads on the
fast mode plus capable devices (and the i2c clock frequency was checked on
RZ/G3S).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Define individual arrays to describe the register offsets. In this way
we can describe different IP variants that share the same register offsets
but have differences in other characteristics. Commit prepares for the
addition of fast mode plus.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add suspend/resume support for the RIIC driver. This is necessary for the
Renesas RZ/G3S SoC which support suspend to deep sleep state where power
to most of the SoC components is turned off. As a result the I2C controller
needs to be reconfigured after suspend/resume. For this, the reset line
was stored in the driver private data structure as well as i2c timings.
The reset line and I2C timings are necessary to re-initialize the
controller after resume.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Enable runtime PM autosuspend support for the RIIC driver. With this, in
case there are consecutive xfer requests the device wouldn't be runtime
enabled/disabled after each consecutive xfer but after the
the delay configured by user. With this, we can avoid touching hardware
registers involved in runtime PM suspend/resume saving in this way some
cycles. The default chosen autosuspend delay is zero to keep the
previous driver behavior.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
pm_runtime_get_sync() may return with error. In case it returns with error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
There is no need to runtime resume the device as long as the IP registers
are not accessed. Calling pm_runtime_get_sync() at the register access
time leads to a simpler error path.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use a temporary variable for the struct device pointers to avoid
dereferencing.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Extend the RIIC driver to support the RZ/V2H(P) ("R9A09G057") SoC. It
accomplishes this by appending the compatible string list and passing
the RZ/V2H-specific OF data.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
With an increasing number of SoCs reusing this driver, each with slight
variations in the RIIC IP, it becomes necessary to support passing these
details as OF data. This approach simplifies the extension of the driver
for other SoCs.
This patch lays the groundwork for adding support for the Renesas RZ/V2H
SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Introduce helper functions for performing I2C read and write operations
in the RIIC driver.
These helper functions lay the groundwork for adding support for the
RZ/V2H SoC. This is essential because the register offsets for the RZ/V2H
SoC differ from those of the RZ/A SoC. By abstracting the read and write
operations, we can seamlessly adapt the driver to support different SoC
variants without extensive modifications.
This patch is part of the preparation process for integrating support for
the RZ/V2H SoC into the RIIC driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Value comes from DT, so it could be 0. Unlikely, but could be.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Asmaa Mnebhi <asnaa@nvidia.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Chris Pringle <chris.pringle@phabrix.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Tali Perry <tali.perry@nuvoton.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use the devm_platform_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Follow the advice of the below link and prefer 'strscpy'. Conversion is
easy because no driver used the return value and has been done with a
simple sed invocation.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Read reset phandle as optional instead of exclusive so that all the DT's
passing the reset phandle can be used to assert/deassert the reset line.
With this change we don't have to differentiate the RZ/G2L SoC.
With the above changes we no longer need the "renesas,riic-r9a07g044"
compatible string, so drop it from riic_i2c_dt_ids[]. No changes are
required to the r9a07g044.dtsi as we already have "renesas,riic-rz" as a
fallback compatible string.
While at it, check the return code of reset_control_deassert() as it might
fail and also add a devres action to assert the reset line.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
RZ/G2L i2c controller is compatible with RZ/A i2c controller.
By default IP is in reset state, so need to perform release
reset before accessing any register.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Since we have generic definitions for bus frequencies, let's use them.
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Robert Richter <rrichter@marvell.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Elie Morisse <syniurge@gmail.com>
Acked-by: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The NACKF flag should be cleared in INTRIICNAKI interrupt processing as
description in HW manual.
This issue shows up quickly when PREEMPT_RT is applied and a device is
probed that is not plugged in (like a touchscreen controller). The result
is endless interrupts that halt system boot.
Fixes: 310c18a41450 ("i2c: riic: add driver")
Cc: stable@vger.kernel.org
Reported-by: Chien Nguyen <chien.nguyen.eb@rvc.renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
- Replace explicit clock handling by Runtime PM calls,
- Streamline Runtime PM handling in error paths,
- Enable Runtime PM in .probe(),
- Disable Runtime PM in .remove(),
- Make sure the device is runtime-resumed when disabling interrupts in
.remove().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Because it looks neater.
For diolan, this allows factoring out some code that is now common
between if and else.
For eg20t, pch_i2c_writebytes is always called with a write in
msgs->flags, and pch_i2c_readbytes with a read.
For imx, i2c_imx_dma_write and i2c_imx_write are always called with a
write in msgs->flags, and i2c_imx_read with a read.
For qup, qup_i2c_write_tx_fifo_v1 is always called with a write in
qup->msg->flags.
For stu300, also restructure debug output for resends, since that
code as a result is only handling debug output.
Reviewed-by: Guenter Roeck <linux@roeck-us.net> [diolan]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [efm32 and imx]
Acked-by: Linus Walleij <linus.walleij@linaro.org> [stu300]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Remove the restriction that the parent clock has to be a specific frequency
and also allow any speed to be supported.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
While modifying the driver to use the STOP interrupt, the completion of the
intermediate transfers need to wake the driver back up in order to initiate
the next transfer (restart condition). Otherwise you get never ending
interrupts and only the first transfer sent.
Fixes: 71ccea095ea1 ("i2c: riic: correctly finish transfers")
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This fixes the condition where the controller has not fully completed its
final transfer and leaves the bus and controller in a undesirable state.
At the end of the last transmitted byte, the existing driver would just
signal for a STOP condition to be transmitted then immediately signal
completion. However, the full STOP procedure might not have fully taken
place by the time the runtime PM shuts off the peripheral clock, leaving
the bus in a suspended state.
Alternatively, the STOP condition on the bus may have completed, but when
the next transaction is requested by the upper layer, not all the
necessary register cleanup was finished from the last transfer which made
the driver return BUS BUSY when it really wasn't.
This patch now makes all transmit and receive transactions wait for the
STOP condition to fully complete before signaling a completed transaction.
With this new method, runtime PM no longer seems to be an issue.
Fixes: 310c18a41450 ("i2c: riic: add driver")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
