| Age | Commit message (Collapse) | Author |
|---|
|
Fix copy-and-paste error in comment for TXB CSI-2 transmitter power down
sequence.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The adv748x assumes input endpoints are always enabled, and registers
a subdevice for each of them when the corresponding output subdevice
is registered.
Fix this by conditionally registering the input subdevice only if it is
actually described in device tree.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The ADV748x has two CSI-2 output port and one TTL input/output port for
digital video reception/transmission. The TTL digital pad is unconditionally
enabled during the device reset even if not used. Same goes for the TXA
and TXB CSI-2 outputs, which are enabled by the initial settings blob
programmed into the chip.
In order to improve power saving, do not enable unused output interfaces:
keep TTL output disabled, as it is not used, and drop CSI-2 output enabling
from the initial settings list, as they get conditionally enabled later.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
As the driver is now allowed to probe with a single output endpoint,
power management routines shall now take into account the case a CSI-2 TX
is not enabled.
Unify the adv748x_tx_power() routine to handle transparently TXA and TXB,
and enable the CSI-2 outputs conditionally.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Currently the adv748x driver will fail to probe unless both of its
output endpoints (TXA and TXB) are connected.
Make the driver support probing provided that there is at least one
input, and one output connected and protect the clean-up function from
accessing un-initialized fields.
Following patches will fix other uses of un-initialized TXs in the driver,
such as power management functions.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This can be done with c99 initializers, which makes the code cleaner
and more transparent. It does require gcc 4.6, because of this bug
in earlier versions:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
Since commit cafa0010cd51 ("Raise the minimum required gcc version to
4.6"), this is the case.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The loop seemed to be made to calculate max, but max is not used in that
function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Change 720p JPEG mode to mode 3 as per other resolutions.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The V4L2 sub-device API does not support the crop default target. A number
of drivers apparently still did support this, likely as it was needed by
the SoC camera framework. Drop support for the default crop rectaingle in
sub-device drivers, and use the bounds rectangle in SoC camera instead.
Reported-by: Helmut Grohne <h.grohne@intenta.de>
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
A number of sub-device drivers used a static name for the sub-device, and
thus the media entity. As the entity name must be unique within a media
device, this makes it impossible to have more than one instance of each
device in a media device. This is a rather severe limitation.
Instead of fixing these drivers, add a comment to the drivers noting that
such static names may not be used in the future.
The alternative of fixing the drivers is troublesome as the entity (as
well as sub-device) name is part of the uAPI. Changing that is almost
certain to break something. As these devices are old but no-one has
encountered a problem with the static names, leave it as-is.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
To make sure the infoframe unpack functions don't end up examining
stack garbage or oopsing, let's pass in the size of the buffer.
v2: Convert tda1997x.c as well (kbuild test robot)
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920185145.1912-3-ville.syrjala@linux.intel.com
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
|
|
These names have been renamed in the CTA-861 standard due to trademark
issues. Replace them here as well so they are in sync with the standard.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The CTA-861 standards have been updated to refer to opRGB instead
of AdobeRGB. The official standard is in fact named opRGB, so
switch to that.
The two old defines referring to ADOBERGB in the public API are
put under #ifndef __KERNEL__ and a comment mentions that they are
deprecated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Several CEC functions are actually specific for use with receivers,
i.e. they should be part of the V4L2 subsystem, not CEC.
These functions deal with validating and modifying EDIDs for (HDMI)
receivers, and they do not actually have anything to do with the CEC
subsystem and whether or not CEC is enabled. The problem was that if
the CEC_CORE config option was not set, then these functions would
become stubs, but that's not right: they should always be valid.
So replace the cec_ prefix by v4l2_ and move them to v4l2-dv-timings.c.
Update all drivers that call these accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Mode setting depends on last mode set, in particular
because of exposure calculation when downscale mode
change between subsampling and scaling.
At stream on the last mode was wrongly set to current mode,
so no change was detected and exposure calculation
was not made, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When switching from auto to manual mode, V4L2 core is calling
g_volatile_ctrl() in manual mode in order to get the manual initial value.
Remove the manual mode check/return to not break this behaviour.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
ov5640_set_mode_exposure_calc() is checking binning value but
binning value read is buggy, fix this.
Rename ov5640_binning_on() to ov5640_get_binning() as per other
similar functions.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Ensure that auto gain and auto exposure are well restored
when changing mode.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Symptom was black image when capturing HD or 5Mp picture
due to manual exposure set to 1 while it was intended to
set autoexposure to "manual", fix this.
Fixes: bf4a4b518c20 ("media: ov5640: Don't force the auto exposure state at start time").
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
As of: commit 476dec012f4c ("media: ov5640: Add horizontal and vertical
totals") the timings parameters gets programmed separately from the
static register values array.
When changing capture mode, the vertical and horizontal totals gets
inspected by the set_mode_exposure_calc() functions, and only later
programmed with the new values. This means exposure, light banding
filter and shutter gain are calculated using the previous timings, and
are thus not correct.
Fix this by programming timings right after the static register value
table has been sent to the sensor in the ov5640_load_regs() function.
Fixes: 476dec012f4c ("media: ov5640: Add horizontal and vertical totals")
Tested-by: Steve Longerbeam <slongerbeam@gmail.com> # i.MX6q SabreSD, CSI-2
Tested-by: Loic Poulain <loic.poulain@linaro.org> # Dragonboard-410c, CSI-2
Signed-off-by: Samuel Bobrowicz <sam@elite-embedded.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Rework the MIPI interface startup sequence with the following changes:
- Remove MIPI bus initialization from the initial settings blob
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At s_stream time enable/disable the MIPI interface output.
- Restore default settings at set_power(0) time.
Before this commit the sensor MIPI interface was initialized with settings
that require a start/stop sequence at power-up time in order to force lanes
into LP11 state, as they were initialized in LP00 when in 'sleep mode',
which is assumed to be the sensor manual definition for the D-PHY defined
stop mode.
The stream start/stop was performed by enabling disabling clock gating,
and had the side effect to change the lanes sleep mode configuration when
stream was stopped.
Clock gating/ungating:
- ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
- on ? 0 : BIT(5));
- if (ret)
Set lanes in LP11 when in 'sleep mode':
- ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
- on ? 0x00 : 0x70);
This commit fixes an issue reported by Jagan Teki on i.MX6 platforms that
prevents the host interface from powering up correctly:
https://lkml.org/lkml/2018/6/1/38
It also improves MIPI capture operations stability on my testing platform
where MIPI capture often failed and returned all-purple frames.
Fixes: f22996db44e2 ("media: ov5640: add support of DVP parallel interface")
Tested-by: Steve Longerbeam <slongerbeam@gmail.com> (i.MX6q SabreSD, CSI-2)
Tested-by: Loic Poulain <loic.poulain@linaro.org> (Dragonboard-410c, CSI-2)
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The function not only does initialization but also registers the subdevice
so change its name to make this more clear.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The driver registers the v4l2 subdevice before attempting to power on the
chip and checking its ID. This means that a media device driver that it's
waiting for this subdevice to be bound, will prematurely expose its media
device node to userspace because if something goes wrong the media entity
will be cleaned up again on the ov2680 probe function.
This also simplifies the probe function error path since no initialization
is made before attempting to enable the resources or checking the chip ID.
Fixes: 3ee47cad3e69 ("media: ov2680: Add Omnivision OV2680 sensor driver")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This code doesn't check for NULL consistently and it generates a Smatch
warning:
drivers/media/i2c/sr030pc30.c:575 sr030pc30_base_config()
error: we previously assumed 'info->pdata' could be null (see line 572)
Fortunately, "info->pdata" can't be NULL to that check can be removed.
The other thing is that if "ret" is an error code here, then we don't
want to do the next call to cam_i2c_write(), so actually let's flip that
test around and return the error. This is more of a theoretical issue
than something which is likely to affect real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The sub-device name is set right after in v4l2_i2c_subdev_init(). Remove
the redundant strcpy() call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Use v4l2_i2c_subdev_set_name() to set the name of the smiapp driver's
sub-devices. There is no functional change.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Currently 2-bytes and 3-bytes registers are read one byte at a time,
doing the needed shift & mask each time.
Replace all of this code by a unique helper function that calls
regmap_bulk_read(), which has two advantages:
- reads all the bytes in a unique I2C transaction
- simplifies code to read multibyte registers
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This parameter holds the number of bytes, not bits.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
A mix of "mode", "format" and "frmfmt" is used to refer to the sensor
readout mode. Use the term "mode" for all of them. Now "format" is
only used in the V4L2 meaning.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Forcibly setting the subdev name to DRIVER_NAME (i.e. "IMX274") makes
it non-unique and less informative.
Let the driver use the default name from i2c, e.g. "IMX274 2-001a".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Rearrange the imx274_start_<N> register tables to better match the
datasheet and slightly simplify code:
- collapes tables 1 and 2, they are applied one after each other and
together they implement the fixed part 1 of the startup procedure
in the datasheet
- while there, cleanup comments
- rename tables 3 and 4 -> 2 and 3, coherently with the datasheet
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The "mode" has been renamed to "binning" in commit 39dd23dc9d4c
("media: imx274: add cropping support via SELECTION API"), but this
define has not been updated.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The device is already suspended when it's the driver's remove function is
called. Remove redundant pm_runtime_set_suspended call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The recent tvp5150 patchset added two new warnings:
drivers/media/i2c/tvp5150.c: In function 'tvp5150_querystd':
drivers/media/i2c/tvp5150.c:829:18: warning: unused variable 'decoder' [-Wunused-variable]
struct tvp5150 *decoder = to_tvp5150(sd);
^~~~~~~
drivers/media/i2c/tvp5150.c:1522:6: warning: no previous prototype for 'tvp5150_volatile_reg' [-Wmissing-prototypes]
bool tvp5150_volatile_reg(struct device *dev, unsigned int reg)
^~~~~~~~~~~~~~~~~~~~
Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When irq is used, the lock is set via IRQ code. When it isn't,
the driver just assumes it is always locked. Instead, read the
lock status from the status register.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add the querystd video_op and make it return V4L2_STD_UNKNOWN while the
TVP5150 is not locked to a signal.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add callback to retrieve the current set norm.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Issue a V4L2_EVENT_SOURCE_CHANGE notification when the TVP5150 locks
onto a signal and when it loses the lock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: partly mainline part port]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
To avoid short frames on stream start, keep output pins at high impedance
while we are not properly locked onto the input signal.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This patch adds an optional interrupt handler to handle the sync
lock interrupt and sync lock status.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[m.felsch@pengutronix.de: move added .g_std callback to separate patch]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
To allow optional interrupt support, we want to configure the pin settings
dynamically. Move those register accesses out of the static initialization
tables.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: drop init_default register remove]
[m.felsch@pengutronix.de: fix regmap access during reset()]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
To trigger standard autodetection only the reset part of the routine
is necessary during probe(). Split this out to make it callable on its own.
[m.felsch@pengutronix.de: adapt commit message]
[m.felsch@pengutronix.de: add tvp5150_enable() to tvp5150_s_stream()]
[m.chehab@samsung.com: fix a compilation breakage]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Make sure to not overwrite decoder->norm when setting the standard
in hardware, but only when instructed by V4L2 API calls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If cropping isn't set explicitly by userspace, reset it to the maximum
possible rectangle in subdevice open if a standard change is detected.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: move code from internal_ops.open() to pad_ops.init_cfg()]
[m.felsch@pengutronix.de: make use of tvp5150_set_default() helper]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The patch adds three macros to bundle the mbus_framefmt default
values and a helper function to set the the default crop and
mbus_framefmt values.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Since commit 9a4c7e68f7e0 ("media: tvp5150: convert register
access to regmap")' the driver supports regmap. Now we can drop
the handmade bit update sequence and move to the regmap provided
helpers.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Regmap provides built in debugging, caching and provides dedicated
accessors for bit manipulations in registers, which make the following
changes a lot simpler.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The function only consists of a single switch case block without a
default case. Unsupported control requests are indicated by the -EINVAL
return code trough the last return statement at the end of the function. So
exiting just the switch case block returns the -EINVAL error code but the
hue control is supported and a zero should be returned instead.
Replace the break by a 'return 0' to fix this behaviour.
Fixes: d183e4efcae8 ("[media] v4l: tvp5150: Add missing break in set
control handler")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
