| Age | Commit message (Collapse) | Author |
|---|
|
soft reset
This driver has two separate reset sequence in different places:
- gpio/HW reset on start of ksz_switch_register()
- SW reset on start of ksz_setup()
The second one will overwrite drive strength configuration made in the
ksz_switch_register().
To fix it, move ksz_parse_drive_strength() from ksz_switch_register() to
ksz_setup().
Fixes: d67d7247f641 ("net: dsa: microchip: Add drive strength configuration")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240304135612.814404-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/page_pool_user.c
0b11b1c5c320 ("netdev: let netlink core handle -EMSGSIZE errors")
429679dcf7d9 ("page_pool: fix netlink dump stop/resume")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This bug was noticed while re-implementing parts of the kernel
driver in userspace using spidev. The goal was to enable some
of the errata workarounds that Microchip describes in their
errata sheet [1].
Both the errata sheet and the regular datasheet of e.g. the KSZ8795
imply that you need to do this for indirect register accesses:
- write a 16-bit value to a control register pair (this value
consists of the indirect register table, and the offset inside
the table)
- either read or write an 8-bit value from the data storage
register (indicated by REG_IND_BYTE in the kernel)
The current implementation has the order swapped. It can be
proven, by reading back some indirect register with known content
(the EEE register modified in ksz8_handle_global_errata() is one of
these), that this implementation does not work.
Private discussion with Oleksij Rempel of Pengutronix has revealed
that the workaround was apparantly never tested on actual hardware.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/Errata/KSZ87xx-Errata-DS80000687C.pdf
Signed-off-by: Tobias Jakobi (Compleo) <tobias.jakobi.compleo@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 7b6e6235b664 ("net: dsa: microchip: ksz8795: handle eee specif erratum")
Link: https://lore.kernel.org/r/20240304154135.161332-1-tobias.jakobi.compleo@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "MT7621 Giga Switch Programming Guide v0.3", "MT7531 Reference Manual
for Development Board v1.0", and "MT7988A Wi-Fi 7 Generation Router
Platform: Datasheet (Open Version) v0.1" documents show that these bits are
enabled at reset:
PMCR_IFG_XMIT(1) (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_MAC_MODE (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_EN
PMCR_RX_EN
PMCR_BACKOFF_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_BACKPR_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_FC_EN
PMCR_RX_FC_EN
These bits also don't exist on the MT7530_PMCR_P(6) register of the switch
on the MT7988 SoC:
PMCR_IFG_XMIT()
PMCR_MAC_MODE
PMCR_BACKOFF_EN
PMCR_BACKPR_EN
Remove the setting of the bits not part of PMCR_LINK_SETTINGS_MASK on
phylink_mac_config as they're already set.
The bit for setting the port on force mode is already done on
mt7530_setup() and mt7531_setup_common(). So get rid of
PMCR_FORCE_MODE_ID() which helped determine which bit to use for the switch
model.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
port_enable and port_disable clears the link settings. Move that to
mt7530_setup() and mt7531_setup_common() which set up the switches. This
way, the link settings are cleared on all ports at setup, and then only
once with phylink_mac_link_down() when a link goes down.
Enable force mode at setup to apply the force part of the link settings.
This ensures that disabled ports will have their link down.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The commit fae463084032 ("net: dsa: mt753x: fix pcs conversion regression")
fixes regression caused by cpu_port_config manually calling phylink
operations. cpu_port_config was deemed useless and was removed. Therefore,
put initialising PCS devices code back to its original order.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is no need for a separate function to call
priv->info->mac_port_config(). Call it from mt753x_phylink_mac_config()
instead and remove mt753x_mac_config().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
priv->info->cpu_port_config() is used for MT7531 and the switch on the
MT7988 SoC. It sets up the ports described as a CPU port earlier than the
phylink code path would do.
This function is useless as:
- Configuring the MACs can be done from the phylink_mac_config code path
instead.
- All the link configuration it does on the CPU ports are later undone with
the port_enable, phylink_mac_config, and then phylink_mac_link_up code
path [1].
priv->p5_interface and priv->p6_interface were being used to prevent
configuring the MACs from the phylink_mac_config code path. Remove them now
that they hold no purpose.
Remove priv->info->cpu_port_config(). On mt753x_phylink_mac_config, switch
to if statements to simplify the code.
Remove the overwriting of the speed and duplex interfaces for certain
interface modes. Phylink already provides the speed and duplex variables
with proper values. Phylink already sets the max speed of TRGMII to
SPEED_1000. Add SPEED_2500 for PHY_INTERFACE_MODE_2500BASEX to where the
speed and EEE bits are set instead.
On the switch on the MT7988 SoC, PHY_INTERFACE_MODE_INTERNAL is being used
to describe the interface mode of the 10G MAC, which is of port 6. On
mt7988_cpu_port_config() PMCR_FORCE_SPEED_1000 was set via the
PMCR_CPU_PORT_SETTING() mask. Add SPEED_10000 case to where the speed bits
are set to cover this. No need to add it to where the EEE bits are set as
the "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open Version)
v0.1" document shows that these bits don't exist on the MT7530_PMCR_P(6)
register.
Remove the definition of PMCR_CPU_PORT_SETTING() now that it holds no
purpose.
Change mt753x_cpu_port_enable() to void now that there're no error cases
left.
Link: https://lore.kernel.org/netdev/ZHy2jQLesdYFMQtO@shell.armlinux.org.uk/ [1]
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove error returns on the cases where they are already handled with the
function the mac_port_get_caps member in mt753x_table points to.
mt7531_mac_config() is also called from mt7531_cpu_port_config() outside of
phylink but the port and interface modes are already handled there.
Change the functions and the mac_port_config function pointer to void now
that there're no error returns anymore.
Remove mt753x_is_mac_port() that used to help the said error returns.
On mt7531_mac_config(), switch to if statements to simplify the code.
Remove internal phy cases from mt753x_phylink_mac_config(), there is no
need to check the interface mode as that's already handled with the
function the mac_port_get_caps member in mt753x_table points to.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According to the document MT7531 Reference Manual for Development Board
v1.0, the SW_PHY_RST bit on the SYS_CTRL register doesn't exist for
MT7531. This is likely why forcing link down on all ports is necessary for
MT7531.
Therefore, do not set SW_PHY_RST on mt7531_setup().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Setting this register related to interrupts is only needed for the MT7530
switch. Make an exclusive check to ensure this.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
For the switch on the MT7988 SoC, the mac_port_config member for ID_MT7988
in mt753x_table is not needed as the interfaces of all MACs are already
handled on mt7988_mac_port_get_caps().
Therefore, remove the mac_port_config member from ID_MT7988 in
mt753x_table. Before calling priv->info->mac_port_config(), if there's no
mac_port_config member in mt753x_table, exit mt753x_mac_config()
successfully.
Remove calling priv->info->mac_port_config() from the sanity check as the
sanity check requires a pointer to a mac_port_config function to be
non-NULL. This will fail for MT7988 as mac_port_config won't be a member of
its info table.
Co-developed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The existing mv88e6390_g2_scratch_gpio_set_smi() cannot be used on the
88E6393X as it requires certain P0_MODE, it also checks the CPU mode
as it impacts the bit setting value.
This is all irrelevant for Amethyst (MV88E6191X/6193X/6393X) as only
the default value of the SMI_PHY Config bit is set to CPU_MGD bootstrap
pin value but it can be changed without restrictions so that GPIO pins
9 and 10 are used as SMI pins.
So, introduce Amethyst specific function and call that if the Amethyst
family wants to setup the external PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The name mv88e6xxx_g2_scratch_gpio_set_smi is a bit ambiguous as it appears
to only be applicable to the 6390 family, so lets rename it to
mv88e6390_g2_scratch_gpio_set_smi to make it more obvious.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for resetting the device using a reset controller,
complementing the existing GPIO reset functionality (reset-gpios).
Although the reset is optional and the driver performs a soft reset
during setup, if the initial reset pin state was asserted, the driver
will not detect the device until the reset is deasserted.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement bridge port isolation for KSZ switches. Enabling the isolation
of switch ports from each other while maintaining connectivity with the
CPU and other forwarding ports. For instance, to isolate swp1 and swp2
from each other, use the following commands:
- bridge link set dev swp1 isolated on
- bridge link set dev swp2 isolated on
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/dev.c
9f30831390ed ("net: add rcu safety to rtnl_prop_list_size()")
723de3ebef03 ("net: free altname using an RCU callback")
net/unix/garbage.c
11498715f266 ("af_unix: Remove io_uring code for GC.")
25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.")
drivers/net/ethernet/renesas/ravb_main.c
ed4adc07207d ("net: ravb: Count packets instead of descriptors in GbEth RX path"
)
c2da9408579d ("ravb: Add Rx checksum offload support for GbEth")
net/mptcp/protocol.c
bdd70eb68913 ("mptcp: drop the push_pending field")
28e5c1380506 ("mptcp: annotate lockless accesses around read-mostly fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While no supported devices currently utilize EXT0, the register reserves
the bits for an EXT0. EXT0 is utilized by devices from the generation
prior to rtl8365mb, such as those supported by the driver library
rtl8367b.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240212-realtek-fix_ext0-v1-1-f3d2536d191a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Embed dsa_switch within realtek_priv to eliminate the need for a second
memory allocation.
Suggested-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The realtek-mdio will now use this driver instead of the generic DSA
driver ("dsa user smi"), which should not be used with OF[1].
With a single ds_ops for both interfaces, the ds_ops in realtek_priv is
no longer necessary. Now, the realtek_variant.ds_ops can be used
directly.
The realtek_priv.setup_interface() has been removed as we can directly
call the new common function.
[1] https://lkml.kernel.org/netdev/20220630200423.tieprdu5fpabflj7@bang-olufsen.dk/T/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the user MDIO driver, despite numerous references to SMI, including
its compatible string, there's nothing inherently specific about the SMI
interface in the user MDIO bus. Consequently, the code has been migrated
to the rtl83xx module. All references to SMI have been eliminated.
The MDIO bus id was changed from Realtek-<switch id> to the switch
devname suffixed with :user_mii, giving more information about the bus
it is referencing.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the line assigning dev.of_node in mdio_bus as subsequent
of_mdiobus_register will always overwrite it.
As discussed in [1], allow the DSA core to be simplified, by not
assigning ds->user_mii_bus when the MDIO bus is described in OF, as it
is unnecessary.
Since commit 3b73a7b8ec38 ("net: mdio_bus: add refcounting for fwnodes
to mdiobus"), we can put the "mdio" node just after the MDIO bus
registration.
[1] https://lkml.kernel.org/netdev/20231213120656.x46fyad6ls7sqyzv@skbuf/T/#u
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The binding docs requires for SMI-connected devices that the switch
must have a child node named "mdio" and with a compatible string of
"realtek,smi-mdio". Meanwile, for MDIO-connected switches, the binding
docs only requires a child node named "mdio".
This patch changes the driver to use the common denominator for both
interfaces, looking for the MDIO node by name, ignoring the compatible
string.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since rtl83xx and realtek-{smi,mdio} are always loaded together,
we can optimize resource usage by consolidating them into a single
module.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some code can be shared between both interface modules (MDIO and SMI)
and among variants. These interface functions migrated to a common
module:
- rtl83xx_lock
- rtl83xx_unlock
- rtl83xx_probe
- rtl83xx_register_switch
- rtl83xx_unregister_switch
- rtl83xx_shutdown
- rtl83xx_remove
The reset during probe was moved to the end of the common probe. This way,
we avoid a reset if anything else fails.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of copying values from the variant, we can keep a reference in
realtek_priv.
This is a preliminary change for sharing code betwen interfaces. It will
allow to move most of the probe into a common module while still allow
code specific to each interface to read variant fields.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, the interface modules realtek-smi and realtek-mdio served as
a platform and an MDIO driver, respectively. Each interface module
redundantly specified the same compatible strings for both variants and
referenced symbols from the variants.
Now, each variant module has been transformed into a unified driver
serving both as a platform and an MDIO driver. This modification
reverses the relationship between the interface and variant modules,
with the variant module now utilizing symbols from the interface
modules.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a namespace to group the exported symbols.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was never used and never referenced.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the DSA loopback fixed PHY module.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20240208164244.3818498-10-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit f86ad77faf24 ("net: dsa: bcm_sf2: Utilize b53_{enable,
disable}_port"), bcm_sf2.c no longer calls b53_eee_enable_set(), and all
its callers are in b53_common.c.
We also need to move it, because it is called within b53_common.c before
its definition, and we want to avoid forward declarations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240206112527.4132299-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's no need to clear the config->supported_interfaces bitmap before
reporting the supported interfaces as all bits in the bitmap will already
be initialized to zero when the phylink_config structure is allocated. The
"config" pointer points to &dp->phylink_config, and "dp" is allocated by
dsa_port_touch() with kzalloc(), so all its fields are filled with zeroes.
There's no code that would change the bitmap beforehand. Remove it.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-7-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On the switch on the MT7988 SoC, as shown in Block Diagram 8.1.1.3 on page
125 of "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open
Version) v0.1", there are only 4 PHYs. That's port 0 to 3. Set the case for
ports which connect to switch PHYs to '0 ... 3'.
Port 4 and 5 are not used at all in this design.
Link: https://wiki.banana-pi.org/Banana_Pi_BPI-R4#Documents [1]
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-6-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pad_setup function pointer was introduced with 88bdef8be9f6 ("net: dsa:
mt7530: Extend device data ready for adding a new hardware"). It was being
used to set up the core clock and port 6 of the MT7530 switch, and pll of
the MT7531 switch.
All of these were moved to more appropriate locations, and it was never
used for the switch on the MT7988 SoC. Therefore, this function pointer
hasn't got a use anymore. Remove it.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-5-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mt7530_pad_clk_setup() is called if port 6 is enabled. It used to do more
things than setting up port 6. That part was moved to more appropriate
locations, mt7530_setup() and mt7530_pll_setup().
Now that all it does is set up port 6, rename it to mt7530_setup_port6(),
and move it to a more appropriate location, under mt7530_mac_config().
Change mt7530_setup_port6() to void as there're no error cases.
Leave an empty mt7530_pad_clk_setup() to satisfy the pad_setup function
pointer.
This is the code path for setting up the ports before:
dsa_switch_ops :: phylink_mac_config() -> mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt753x_info :: mac_port_config() -> mt7530_mac_config()
-> mt7530_setup_port5()
-> mt753x_pad_setup()
-> mt753x_info :: pad_setup() -> mt7530_pad_clk_setup()
This is after:
dsa_switch_ops :: phylink_mac_config() -> mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt753x_info :: mac_port_config() -> mt7530_mac_config()
-> mt7530_setup_port5()
-> mt7530_setup_port6()
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-4-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This code is from before this driver was converted to phylink API. Phylink
deals with the unsupported interface cases before mt7530_pad_clk_setup() is
run. Therefore, the default case would never run. However, it must be
defined nonetheless to handle all the remaining enumeration values, the
phy-modes.
Switch to if statement for RGMII and return which simplifies the code and
saves an indent.
Set P6_INTF_MODE, which is the three least significant bits of the
MT7530_P6ECR register, to 0 for RGMII even though it will already be 0
after reset. This is to keep supporting dynamic reconfiguration of the port
in the case the interface changes from TRGMII to RGMII.
Disable the TRGMII clocks for all cases. They will be enabled if TRGMII is
being used.
Read XTAL after checking for RGMII as it's only needed for the TRGMII
interface mode.
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-3-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The crystal frequency concerns the switch core. The frequency should be
checked when the switch is being set up so the driver can reject the
unsupported hardware earlier and without requiring port 6 to be used.
Move it to mt7530_setup(). Drop the unnecessary function printing.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-2-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
On the first code path, priv->p5_intf_sel is either set to
P5_INTF_SEL_PHY_P0 or P5_INTF_SEL_PHY_P4 when mt7530_setup_port5() is run.
On the second code path, priv->p5_intf_sel is set to P5_INTF_SEL_GMAC5 when
mt7530_setup_port5() is run.
Empty the default case which will never run but is needed nonetheless to
handle all the remaining enumeration values.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-1-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
b53_get_mac_eee() sets both eee_enabled and eee_active, and then
returns zero.
dsa_slave_get_eee(), which calls this function, will then continue to
call phylink_ethtool_get_eee(), which will return -EOPNOTSUPP if there
is no PHY present, otherwise calling phy_ethtool_get_eee() which in
turn will call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Thus, when there is no PHY, dsa_slave_get_eee() will fail with
-EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to
userspace. When there is a PHY, eee_enabled and eee_active will be
overwritten by phylib, making the setting of these members in
b53_get_mac_eee() entirely unnecessary.
Remove this code, thus simplifying b53_get_mac_eee().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1rWbNI-002cCz-4x@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MDIO bus drivers can return -ENODEV when they know the bus does not
have a device at the given address, e.g. because of hardware
limitation. One such limitation is that the bus does not support C45
at all. This is more efficient than returning 0xffff, since it
immediately stops the probing on the given address, where as further
reads can be made when 0xffff is returned.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was pointed out during the review [1] of commit 68e1010cda79 ("net:
dsa: qca8k: put MDIO bus OF node on qca8k_mdio_register() failure") that
the rest of the qca8k driver uses "int ret" rather than "int err".
Make everything consistent in that regard, not only
qca8k_mdio_register(), but also qca8k_setup_mdio_bus().
[1] https://lore.kernel.org/netdev/qyl2w3ownx5q7363kqxib52j5htar4y6pkn7gen27rj45xr4on@pvy5agi6o2te/
Suggested-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was pointed out during the review [1] of commit e66bf63a7f67 ("net:
dsa: qca8k: skip MDIO bus creation if its OF node has status =
"disabled"") that we now leak a reference to the "mdio" OF node if it is
disabled.
This is only a concern when using dynamic OF as far as I can tell (like
probing on an overlay), since OF nodes are never freed in the regular
case. Additionally, I'm unaware of any actual device trees (in
production or elsewhere) which have status = "disabled" for the MDIO OF
node. So handling this as a simple enhancement.
[1] https://lore.kernel.org/netdev/CAJq09z4--Ug+3FAmp=EimQ8HTQYOWOuVon-PUMGB5a1N=RPv4g@mail.gmail.com/
Suggested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit introduces support for the KSZ8567, a robust 7-port
Ethernet switch. The KSZ8567 features two RGMII/MII/RMII interfaces,
each capable of gigabit speeds, complemented by five 10/100 Mbps
MAC/PHYs.
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240130083419.135763-2-dev@pschenker.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Not all mv88e6xxx device support C45 read/write operations. Those
which do not return -EOPNOTSUPP. However, when phylib scans the bus,
it considers this fatal, and the probe of the MDIO bus fails, which in
term causes the mv88e6xxx probe as a whole to fail.
When there is no device on the bus for a given address, the pull up
resistor on the data line results in the read returning 0xffff. The
phylib core code understands this when scanning for devices on the
bus. C45 allows multiple devices to be supported at one address, so
phylib will perform a few reads at each address, so although thought
not the most efficient solution, it is a way to avoid fatal
errors. Make use of this as a minimal fix for stable to fix the
probing problems.
Follow up patches will rework how C45 operates to make it similar to
C22 which considers -ENODEV as a none-fatal, and swap mv88e6xxx to
using this.
Cc: stable@vger.kernel.org
Fixes: 743a19e38d02 ("net: dsa: mv88e6xxx: Separate C22 and C45 transactions")
Reported-by: Tim Menninger <tmenninger@purestorage.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129224948.1531452-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When working with GPIO, its direction must be set either when the GPIO is
requested by gpiod_get*() or later on by one of the gpiod_direction_*()
functions. Neither of this is done here which results in undefined
behavior on some systems.
As the reset GPIO is used right after it is requested here, it makes sense
to configure it as GPIOD_OUT_HIGH right away. With that, the following
gpiod_set_value_cansleep(1) becomes redundant and can be safely
removed.
Fixes: a653f2f538f9 ("net: dsa: qca8k: introduce reset via gpio feature")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1706266175-3408-1-git-send-email-michal.vokac@ysoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's no need to run all the code on mt7530_setup_port5() if port 5 is
disabled. The only case for calling mt7530_setup_port5() from
mt7530_setup() is when PHY muxing is enabled. That is because port 5 is not
defined as a port on the devicetree, therefore, it cannot be controlled by
phylink.
Because of this, run mt7530_setup_port5() if priv->p5_intf_sel is
P5_INTF_SEL_PHY_P0 or P5_INTF_SEL_PHY_P4. Remove the P5_DISABLED case from
mt7530_setup_port5().
Stop initialising the interface variable as the remaining cases will always
call mt7530_setup_port5() with it initialised.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-7-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Running mt7530_setup_port5() from mt7530_setup() used to handle all cases
of configuring port 5, including phylink.
Setting priv->p5_interface under mt7530_setup_port5() makes sure that
mt7530_setup_port5() from mt753x_phylink_mac_config() won't run.
The commit ("net: dsa: mt7530: improve code path for setting up port 5")
makes so that mt7530_setup_port5() from mt7530_setup() runs only on
non-phylink cases.
Get rid of unnecessarily setting priv->p5_interface under
mt7530_setup_port5() as port 5 phylink configuration will be done by
running mt7530_setup_port5() from mt753x_phylink_mac_config() now.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-6-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.
Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().
Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. This driver isn't in the
dsa_switches_apply_workarounds[] array so phylink will always be present.
To keep the cases where port 5 isn't controlled by phylink working as
before, preserve the mt7530_setup_port5() call from mt7530_setup().
Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.
Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.
Improve the comment which explains the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-5-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
