| Age | Commit message (Collapse) | Author |
|---|
|
The default return value -EOPNOTSUPP of mv88e6xxx_port_bridge_flags()
came from the return value of the DSA method port_egress_floods() in
commit 4f85901f0063 ("net: dsa: mv88e6xxx: add support for bridge flags"),
but the DSA API was changed in commit a8b659e7ff75 ("net: dsa: act as
passthrough for bridge port flags"), resulting in the return value
-EOPNOTSUPP not being valid anymore, and sections for new flags will not
need to set the return value to zero on success, as with the new mab flag
added in a following patch.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Improve mdio master read/write by using singe mii read/write lo/hi.
In a read and write we need to poll the mdio master regs in a busy loop
to check for a specific bit present in the upper half of the reg. We can
ignore the other half since it won't contain useful data. This will save
an additional useless read for each read and write operation.
In a read operation the returned data is present in the mdio master reg
lower half. We can ignore the other half since it won't contain useful
data. This will save an additional useless read for each read operation.
In a read operation it's needed to just set the hi half of the mdio
master reg as the lo half will be replaced by the result. This will save
an additional useless write for each read operation.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It may be useful to read/write just the lo or hi half of a reg.
This is especially useful for phy poll with the use of mdio master.
The mdio master reg is composed by the first 16 bit related to setup and
the other half with the returned data or data to write.
Refactor the mii function to permit single mii read/write of lo or hi
half of the reg.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 2481d206fae7884cd07014fd1318e63af35e99eb.
The Documentation is very confusing about the topic.
The cache logic for hi and lo is wrong and actually miss some regs to be
actually written.
What the Documentation actually intended was that it's possible to skip
writing hi OR lo if half of the reg is not needed to be written or read.
Revert the change in favor of a better and correct implementation.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The assumption that Documentation was right about how this value work was
wrong. It was discovered that the length value of the mgmt header is in
step of word size.
As an example to process 4 byte of data the correct length to set is 2.
To process 8 byte 4, 12 byte 6, 16 byte 8...
Odd values will always return the next size on the ack packet.
(length of 3 (6 byte) will always return 8 bytes of data)
This means that a value of 15 (0xf) actually means reading/writing 32 bytes
of data instead of 16 bytes. This behaviour is totally absent and not
documented in the switch Documentation.
In fact from Documentation the max value that mgmt eth can process is
16 byte of data while in reality it can process 32 bytes at once.
To handle this we always round up the length after deviding it for word
size. We check if the result is odd and we round another time to align
to what the switch will provide in the ack packet.
The workaround for the length limit of 15 is still needed as the length
reg max value is 0xf(15)
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Fixes: 90386223f44e ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP hardware timestamping related objects are not linked when PTP
support for MV88E6xxx (NET_DSA_MV88E6XXX_PTP) is disabled, therefore
NET_DSA_MV88E6XXX should not depend on PTP_1588_CLOCK_OPTIONAL
regardless of NET_DSA_MV88E6XXX_PTP.
Instead, condition more strictly on how NET_DSA_MV88E6XXX_PTP's
dependencies are met, making sure that it cannot be enabled when
NET_DSA_MV88E6XXX=y and PTP_1588_CLOCK=m.
In other words, this commit allows NET_DSA_MV88E6XXX to be built-in
while PTP_1588_CLOCK is a module, as long as NET_DSA_MV88E6XXX_PTP is
prevented from being enabled.
Fixes: e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies")
Signed-off-by: Johnny S. Lee <foss@jsl.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ swithes used interrupts for detecting the phy link up and down.
During registering the interrupt handler, it used IRQF_TRIGGER_FALLING
flag. But this flag has to be retrieved from device tree instead of hard
coding in the driver, so removing the flag.
Fixes: ff319a644829 ("net: dsa: microchip: move interrupt handling logic from lan937x to ksz_common")
Reported-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20221213101440.24667-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King correctly pointed out that the MAC_2500FD capability is
already added for port 5 (if not in RGMII mode) and port 6 (which only
supports SGMII) by mt7531_mac_port_get_caps. Remove the reduntant
setting of this capability flag which was added by a previous commit.
Fixes: e19de30d2080 ("net: dsa: mt7530: add support for in-band link status")
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/Y5qY7x6la5TxZxzX@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the blamed commit, it was not noticed that one implementation of
chip->info->ops->phylink_get_caps(), called by mv88e6xxx_get_caps(),
may access hardware registers, and in doing so, it takes the
mv88e6xxx_reg_lock(). Namely, this is mv88e6352_phylink_get_caps().
This is a problem because mv88e6xxx_get_caps(), apart from being
a top-level function (method invoked by dsa_switch_ops), is now also
directly called from mv88e6xxx_setup_port(), which runs under the
mv88e6xxx_reg_lock() taken by mv88e6xxx_setup(). Therefore, when running
on mv88e6352, the reg_lock would be acquired a second time and the
system would deadlock on driver probe.
The things that mv88e6xxx_setup() can compete with in terms of register
access with are the IRQ handlers and MDIO bus operations registered by
mv88e6xxx_probe(). So there is a real need to acquire the register lock.
The register lock can, in principle, be dropped and re-acquired pretty
much at will within the driver, as long as no operations that involve
waiting for indirect access to complete (essentially, callers of
mv88e6xxx_smi_direct_wait() and mv88e6xxx_wait_mask()) are interrupted
with the lock released. However, I would guess that in mv88e6xxx_setup(),
the critical section is kept open for such a long time just in order to
optimize away multiple lock/unlock operations on the registers.
We could, in principle, drop the reg_lock right before the
mv88e6xxx_setup_port() -> mv88e6xxx_get_caps() call, and
re-acquire it immediately afterwards. But this would look ugly, because
mv88e6xxx_setup_port() would release a lock which it didn't acquire, but
the caller did.
A cleaner solution to this issue comes from the observation that struct
mv88e6xxxx_ops methods generally assume they are called with the
reg_lock already acquired. Whereas mv88e6352_phylink_get_caps() is more
the exception rather than the norm, in that it acquires the lock itself.
Let's enforce the same locking pattern/convention for
chip->info->ops->phylink_get_caps() as well, and make
mv88e6xxx_get_caps(), the top-level function, acquire the register lock
explicitly, for this one implementation that will access registers for
port 4 to work properly.
This means that mv88e6xxx_setup_port() will no longer call the top-level
function, but the low-level mv88e6xxx_ops method which expects the
correct calling context (register lock held).
Compared to chip->info->ops->phylink_get_caps(), mv88e6xxx_get_caps()
also fixes up the supported_interfaces bitmap for internal ports, since
that can be done generically and does not require per-switch knowledge.
That's code which will no longer execute, however mv88e6xxx_setup_port()
doesn't need that. It just needs to look at the mac_capabilities bitmap.
Fixes: cc1049ccee20 ("net: dsa: mv88e6xxx: fix speed setting for CPU/DSA ports")
Reported-by: Maksim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20221214110120.3368472-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Merge in the left-over fixes before the net-next pull-request.
net/mptcp/subflow.c
d3295fee3c75 ("mptcp: use proper req destructor for IPv6")
36b122baf6a8 ("mptcp: add subflow_v(4,6)_send_synack()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It is possible to trigger these VTU violation messages very easily,
it's only necessary to send packets with an unknown VLAN ID to a port
that belongs to a VLAN-aware bridge.
Do a similar thing as for ATU violation messages, and hide them in the
kernel's trace buffer.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_vtu_miss_violation
mv88e6xxx:mv88e6xxx_vtu_member_violation
$ trace-cmd report
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the MV88E6XXX_PORT_ASSOC_VECTOR_INT_AGE_OUT bit (interrupt on
age out) is not enabled by the driver, and as a result, the print for
age out violations is dead code.
Remove it until there is some way for this to be triggered.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch fixes an issue where a read failure of a port statistic counter
will return unknown results. While it is highly unlikely the read will
ever fail, it is much cleaner to return a zero for the stat count.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221209153502.7429-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.
The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.
The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.
The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.
With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.
Kernel log:
sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Fixes: 38fbe91f2287 ("net: dsa: sja1105: configure the multicast policers, if present")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Nicolae Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20221207132347.38698-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add stats64 support for ksz8xxx series of switches.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20221205052904.2834962-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ethernet-controller dt-schema, mostly pushed forward by Linux, has
the "internal" PHY mode for denoting MAC connections to an internal PHY.
U-Boot may provide device tree blobs where this phy-mode is specified,
so make the Linux driver accept them.
It appears that the current behavior with phy-mode = "internal" was
introduced when mv88e6xxx started reporting supported_interfaces to
phylink. Prior to that, I don't think it would have any issues accepting
this phy-mode.
Fixes: d4ebf12bcec4 ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Link: https://lore.kernel.org/linux-arm-kernel/20221205172709.kglithpbhdbsakvd@skbuf/T/
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx6q-gw904.dts
Link: https://lore.kernel.org/r/20221205194845.2131161-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
To make the code more comparable to KSZ9477 code, move DSA
configurations to the same location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
compatible switches
KSZ8795 and KSZ9477 compatible series of switches use global max frame
size configuration register. So, enable MTU normalization for this reason.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.
With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.
This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add ksz_rmw8(), it will be used in the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If we have global MTU configuration, it is enough to configure it on CPU
port only.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Arun Ramadoss <arun.ramadoss@microchip.com> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When dsa_devlink_region_create failed in sja1105_setup_devlink_regions(),
priv->regions is not released.
Fixes: bf425b82059e ("net: dsa: sja1105: expose static config as devlink region")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221205012132.2110979-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver name is available in device_driver::name. Right now,
drivers still have to report this piece of information themselves in
their devlink_ops::info_get callback function.
In order to factorize code, make devlink_nl_info_fill() add the driver
name attribute.
Now that the core sets the driver name attribute, drivers are not
supposed to call devlink_info_driver_name_put() anymore. Remove
devlink_info_driver_name_put() and clean-up all the drivers using this
function in their callback.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tools/lib/bpf/ringbuf.c
927cbb478adf ("libbpf: Handle size overflow for ringbuf mmap")
b486d19a0ab0 ("libbpf: checkpatch: Fixed code alignments in ringbuf.c")
https://lore.kernel.org/all/20221121122707.44d1446a@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch changes the reported ethtool statistics for the lan9303
family of parts covered by this driver.
The TxUnderRun statistic label is renamed to RxShort to accurately
reflect what stat the device is reporting. I did not reorder the
statistics as that might cause problems with existing user code that
are expecting the stats at a certain offset.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221128193559.6572-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is no reason that I can see why the no-op tagging protocol should
be registered manually, so make it a module and make all drivers which
have any sort of reference to DSA_TAG_PROTO_NONE select it.
Note that I don't know if ksz_get_tag_protocol() really needs this,
or if it's just the logic which is poorly written. All switches seem to
have their own tagging protocol, and DSA_TAG_PROTO_NONE is just a
fallback that never gets used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ever since commit 4d1d157fb6a4 ("net: mscc: ocelot: share the common stat
definitions between all drivers") the stats_layout entry in ocelot and
felix drivers have become redundant. Remove the unnecessary code.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
You'd think people know that the internal 100BASE-TX PHY on the SJA1110
responds only to clause 22 MDIO transactions, but they don't :)
When a clause 45 transaction is attempted, sja1105_base_tx_mdio_read()
and sja1105_base_tx_mdio_write() don't expect "reg" to contain bit 30
set (MII_ADDR_C45) and pack this value into the SPI transaction buffer.
But the field in the SPI buffer has a width smaller than 30 bits, so we
see this confusing message from the packing() API rather than a proper
rejection of C45 transactions:
Call trace:
dump_stack+0x1c/0x38
sja1105_pack+0xbc/0xc0 [sja1105]
sja1105_xfer+0x114/0x2b0 [sja1105]
sja1105_xfer_u32+0x44/0xf4 [sja1105]
sja1105_base_tx_mdio_read+0x44/0x7c [sja1105]
mdiobus_read+0x44/0x80
get_phy_c45_ids+0x70/0x234
get_phy_device+0x68/0x15c
fwnode_mdiobus_register_phy+0x74/0x240
of_mdiobus_register+0x13c/0x380
sja1105_mdiobus_register+0x368/0x490 [sja1105]
sja1105_setup+0x94/0x119c [sja1105]
Cannot store 401d2405 inside bits 24-4 (would truncate)
Fixes: 5a8f09748ee7 ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop the custom implementation of phylink_validate() in favor of the
generic one, which requires config->mac_capabilities to be set.
This was used up until now because of the possibility of being paired
with Aquantia PHYs with support for rate matching. The phylink framework
gained generic support for these, and knows to advertise all 10/100/1000
lower speed link modes when our SERDES protocol is 2500base-x
(fixed speed).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enabling set_policy capability for mv88e6321.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221110091027.998073-1-angelo.dureghello@timesys.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Probe functions uses normal dev_err() to check error conditions
and print messages. Replace dev_err() with dev_err_probe() to
have more standardized format and error logging.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add status validation for port register write inside
lan937x_change_mtu. ksz_pwrite and ksz_pread api's are
updated with return type int (Reference patch mentioned
below). Update lan937x_change_mtu with status validation
for ksz_pwrite16().
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220826105634.3855578-6-o.rempel@pengutronix.de/
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add device irq in i2c probe function.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
compatible string
Add KSZ9563 inside ksz_switch_chips structure with
port_nirq as 3. KSZ9563 use KSZ9893 switch parameters
but port_nirq count is 3 for KSZ9563 whereas 2 for
KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate
member and from device tree map compatible string into
KSZ9563 inside ksz_spi.c and ksz9477_i2c.c.
Global Chip ID 1 and 2 registers read value 9893, select
sku based on Global Chip ID 4 Register which read 0x1c
for KSZ9563.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the .port_set_rgmii_delay hook is missing for the 88E6320
family, which causes failure to retrieve an IP address via DHCP.
Add mv88e6320_port_set_rgmii_delay() that allows applying the RGMII
delay for ports 2, 5, and 6, which are the only ports that can be used
in RGMII mode.
Tested on a custom i.MX8MN board connected to an 88E6320 switch.
This change also applies safely to the 88E6321 variant.
The only difference between 88E6320 versus 88E6321 is the temperature
grade and pinout.
They share exactly the same MDIO register map for ports 2, 5, and 6,
which are the only ports that can be used in RGMII mode.
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
[fabio: Improved commit log and extended it to mv88e6321_ops]
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221028163158.198108-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
kmemleak reported memory leaks in dsa_loop_init():
kmemleak: 12 new suspected memory leaks
unreferenced object 0xffff8880138ce000 (size 2048):
comm "modprobe", pid 390, jiffies 4295040478 (age 238.976s)
backtrace:
[<000000006a94f1d5>] kmalloc_trace+0x26/0x60
[<00000000a9c44622>] phy_device_create+0x5d/0x970
[<00000000d0ee2afc>] get_phy_device+0xf3/0x2b0
[<00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0
[<000000008a834798>] fixed_phy_register+0x84/0xb0
[<0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop]
...
There are two reasons for memleak in dsa_loop_init().
First, fixed_phy_register() create and register phy_device:
fixed_phy_register()
get_phy_device()
phy_device_create() # freed by phy_device_free()
phy_device_register() # freed by phy_device_remove()
But fixed_phy_unregister() only calls phy_device_remove().
So the memory allocated in phy_device_create() is leaked.
Second, when mdio_driver_register() fail in dsa_loop_init(),
it just returns and there is no cleanup for phydevs.
Fix the problems by catching the error of mdio_driver_register()
in dsa_loop_init(), then calling both fixed_phy_unregister() and
phy_device_free() to release phydevs.
Also add a function for phydevs cleanup to avoid duplacate.
Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch sends autocast mib in little-endian. This is problematic for
big-endian system as the values needs to be converted.
Fix this by converting each mib value to cpu byte order.
Fixes: 5c957c7ca78c ("net: dsa: qca8k: add support for mib autocast in Ethernet packet")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The header and the data of the skb for the inband mgmt requires
to be in little-endian. This is problematic for big-endian system
as the mgmt header is written in the cpu byte order.
Fix this by converting each value for the mgmt header and data to
little-endian, and convert to cpu byte order the mgmt header and
data sent by the switch.
Fixes: 5950c7c0a68c ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
|
|
Add support for configuring the max SDU per priority and per port. If not
specified, keep the default.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The following patch will need to make this function also respond to
TC_QUERY_BASE, so make the processing more structured around the
tc_setup_type.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
