summaryrefslogtreecommitdiff
path: root/drivers/net/usb/r8152.c
AgeCommit message (Collapse)Author
2015-02-07r8152: use BIT macrohayeswang
Use BIT macro to replace (1 << bits). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07r8152: replace get_protocol with vlan_get_protocolhayeswang
vlan_get_protocol() has been defined and use it to replace get_protocol(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07r8152: adjust the line feed for hw_featureshayeswang
Keep NETIF_F_HW_VLAN_CTAG_RX and NETIF_F_HW_VLAN_CTAG_TX at the same line. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07r8152: check RTL8152_UNPLUG for rtl8152_closehayeswang
It is unnecessary to accress the hw register if the device is unplugged. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07r8152: check linking status with netif_carrier_okhayeswang
Replace (tp->speed & LINK_STATUS) with netif_carrier_ok(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07r8152: adjust lpm timerhayeswang
Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at USB 3.0. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07r8152: adjust rx_bottomhayeswang
If a error occurs when submitting rx, skip the remaining submissions and try to submit them again next time. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: arch/arm/boot/dts/imx6sx-sdb.dts net/sched/cls_bpf.c Two simple sets of overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-19r8152: remove sram_readhayeswang
Read OCP register 0xa43a~0xa43b would clear some flags which the hw would use, and it may let the device lost. However, the unit of reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling sram_read() to read OCP_SRAM_DATA. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-19r8152: remove generic_ocp_read before writinghayeswang
For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read() which is used to read the whole 4 byte data, keep the unchanged bytes, and modify the expected bytes. However, the "byen" could be used to determine which bytes of the 4 bytes to write, so the action could be removed. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-14r8152: replace tasklet with NAPIhayeswang
Replace tasklet with NAPI. Add rx_queue to queue the remaining rx packets if the number of the rx packets is more than the request from poll(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-13net: rename vlan_tx_* helpers since "tx" is misleading thereJiri Pirko
The same macros are used for rx as well. So rename it. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-12r8152: check the status before submitting rxhayeswang
Don't submit the rx if the device is unplugged, stopped, or linking down. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-12r8152: call rtl_start_rx after netif_carrier_onhayeswang
Remove rtl_start_rx() from rtl_enable() and put it after calling netif_carrier_on(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-06r8152: support ndo_features_checkhayeswang
Support ndo_features_check to avoid: - the transport offset is more than the hw limitation when using hw checksum. - the skb->len of a GSO packet is more than the limitation. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-09r8152: redefine REALTEK_USB_DEVICEhayeswang
Redefine REALTEK_USB_DEVICE for the desired USB interface for probe(). There are three USB interfaces for the device. USB_CLASS_COMM and USB_CLASS_CDC_DATA are for ECM mode (config #2). USB_CLASS_VENDOR_SPEC is for the vendor mode (config #1). However, we are not interesting in USB_CLASS_CDC_DATA for probe(), so redefine REALTEK_USB_DEVICE to ignore the USB interface class of USB_CLASS_CDC_DATA. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21r8152: adjust rtl_start_rxhayeswang
If there is a error for r8152_submit_rx(), add the remaining rx buffers to the list. Then the remaining rx buffers could be submitted later. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21r8152: adjust r8152_submit_rxhayeswang
The behavior of handling the returned status from r8152_submit_rx() is almost same, so let r8152_submit_rx() deal with the error directly. This could avoid the duplicate code. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-12r8152: check RTL8152_UNPLUG and netif_running before autoresumehayeswang
If the device is unplugged or !netif_running(), the workqueue doesn't need to wake the device, and could return directly. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-12r8152: clear the flag of SCHEDULE_TASKLET in tasklethayeswang
Clear the flag of SCHEDULE_TASKLET in bottom_half() to avoid re-schedule the tasklet again by workqueue. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-12r8152: remove the duplicate init for the list of rx_donehayeswang
The INIT_LIST_HEAD(&tp->rx_done) would be done in rtl_start_rx(), so remove the unnecessary one in alloc_all_mem(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-06r8152: remove the definitions of the PIDhayeswang
The PIDs are only used in the id table, so the definitions are unnacessary. Remove them wouldn't have confusion. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-06r8152: modify rtl_ops_inithayeswang
Replace using VID/PID with using tp->version to initialize the ops. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-06r8152: move r8152b_get_versionhayeswang
Move r8152b_get_version() to the location before rtl_ops_init(). Then, the rtl_ops_init() could use tp->version. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05r8152: disable the tasklet by defaulthayeswang
Let the tasklet only be enabled after open(), and be disabled for the other situation. The tasklet is only necessary after open() for tx/rx, so it could be disabled by default. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/phy/marvell.c Simple overlapping changes in drivers/net/phy/marvell.c Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-31r8152: stop submitting intr for -EPROTOhayeswang
For Renesas USB 3.0 host controller, when unplugging the usb hub which has the RTL8153 plugged, the driver would get -EPROTO for interrupt transfer. There is high probability to get the information of "HC died; cleaning up", if the driver continues to submit the interrupt transfer before the disconnect() is called. [ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.383097] usb 9-1: USB disconnect, device number 2 [ 1024.383103] usb 9-1.4: USB disconnect, device number 6 [ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command. [ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host. [ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up [ 1029.421480] usb 8-1: USB disconnect, device number 2 Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30r8152: set RTL8152_UNPLUG when finding -ENODEVhayeswang
Set RTL8152_UNPLUG when finding -ENODEV. This could accelerate unloading the driver when the device is unplugged. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30r8152: check WORK_ENABLE in suspend functionhayeswang
Avoid unnecessary behavior when autosuspend occurs during open(). The relative processes should only be run after finishing open(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30r8152: reset tp->speed before autoresuming in open functionhayeswang
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume() would call rtl_start_rx() before enabling the tx/rx. Avoid this by resetting it to zero. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30r8152: clear SELECTIVE_SUSPEND when autoresuminghayeswang
The flag of SELECTIVE_SUSPEND should be cleared when autoresuming. Otherwise, when the system suspend and resume occur, it may have the wrong flow. Besides, because the flag of SELECTIVE_SUSPEND couldn't be used to check if the hw enables the relative feature, it should alwayes be disabled in close(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-29r8152: support nway_reset of ethtoolhayeswang
Support the nway_reset() function for ethtool. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-29r8152: rename tx_underunhayeswang
Replace tx_underun with tx_underrun for checkpatch.pl. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-17r8152: return -EBUSY for runtime suspendhayeswang
Remove calling cancel_delayed_work_sync() for runtime suspend, because it would cause dead lock. Instead, return -EBUSY to avoid the device enters suspending if the net is running and the delayed work is pending or running. The delayed work would try to wake up the device later, so the suspending is not necessary. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-09r8152: add mutex for hw settingshayeswang
Use the mutex to avoid the settings are interrupted by other ones. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-09r8152: adjust usb_autopm_xxxhayeswang
Add usb_autopm_xxx for rtl8152_get_settings() ,and remove usb_autopm_xxx from read_mii_word() and write_mii_word(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-09r8152: autoresume before setting featurehayeswang
Resume the device before setting the feature. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2014-10-06r8152: nway reset after setting eeehayeswang
Restart autonegotiation is necessary after setting EEE. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-03r8152: autoresume before setting MAC addresshayeswang
Resume the device before setting the MAC address. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/usb/r8152.c net/netfilter/nfnetlink.c Both r8152 and nfnetlink conflicts were simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-01r8152: disable power cut for RTL8153hayeswang
The firmware would be clear when the power cut is enabled for RTL8153. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-01r8152: remove clearing bphayeswang
The xxx_clear_bp() is used to halt the firmware. It only necessary for updating the new firmware. Besides, depend on the version of the current firmware, it may have problem to halt the firmware directly. Finally, halt the firmware would let the firmware code useless, and the bugs which are fixed by the firmware would occur. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-30r8152: fix setting RTL8152_UNPLUGhayeswang
The flag of RTL8152_UNPLUG should only be set when the device is unplugged, not each time the rtl8152_disconnect() is called. Otherwise, the device wouldn't be stopped normally. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-28r8152: support ethtool eeehayeswang
Support get_eee() and set_eee() of ethtool_ops. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-28r8152: add functions to set EEEhayeswang
Add functions to enable EEE and set EEE advertisement. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-28r8152: change the EEE definitionhayeswang
Replace the EEE definitions with the ones which is declared in "mdio.h". Chage some definitions to make them readable. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-26r8152: fix the carrier off when autoresuminghayeswang
netif_carrier_off would be called when autoresuming, even though the cable is plugged. This causes some applications do relative actions when detecting the carrier off. Keep the status of the carrier, and let it be modified when the linking change occurs. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: arch/mips/net/bpf_jit.c drivers/net/can/flexcan.c Both the flexcan and MIPS bpf_jit conflicts were cases of simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-22r8152: disable ALDPShayeswang
If the hw is in ALDPS mode, the hw may have no response for accessing the most registers. Therefore, the ALDPS should be disabled before accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(), and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw wouldn't enter ALDPS mode when linking on. The hw would enter the ALDPS mode after several seconds when link down occurs and the ALDPS is enabled. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-07-18 08:47:29 +0000