| Age | Commit message (Collapse) | Author |
|---|
|
Currently interface mode is determined each time a vdev is created.
In MLO scenario where there could be multiple vdevs this is just a
waste of time.
Move related logic into a new helper ath12k_mac_determine_vdev_type()
and call it once in ath12k_mac_op_add_interface().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-7-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently we only build regdomain when channel list event is received.
That event is received when driver boots or when a new country code is
sent to firmware. At either time we may have no information about
interface mode or AP's power type, consequently WMI_REG_INDOOR_AP is
selected. In upcoming patches we will rebuild regdomain once those
information is available. For that purpose reg info has to be
stored/refreshed each time a new channel list event is received.
The stored reg info would be freed in ath12k_reg_free() when it is not
needed.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-6-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The reg info is allocated in ath12k_reg_chan_list_event() but validated
in ath12k_reg_handle_chan_list(). Currently this is good since reg info
would be freed regardless of validation results. However in an upcoming
patch the reg info might need to be stored for later use if the result
is good. Since we can not tell the result from return value of
ath12k_reg_handle_chan_list(), we need to move validation out of it.
Add a new helper ath12k_reg_validate_reg_info() and call it in
ath12k_reg_chan_list_event(), based on the result we can choose to store
or free it in the following patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-5-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
For 6 GHz band, firmware offers 3 types of regulatory rules for AP
mode and 6 for station mode in WMI_REG_CHAN_LIST_CC_EXT_EVENTID event.
In ath12k_reg_build_regd() current code by default chooses
WMI_REG_INDOOR_AP type rules from AP mode reg list to build regdomain,
regardless of the interface mode and power type, hence is not correct.
Pass interface mode (wmi_vdev_type) and AP power type
(ieee80211_ap_reg_power) as new arguments to ath12k_reg_build_regd()
such that we can choose correct rules based on them. Currently
ath12k_reg_build_regd() is called only by ath12k_reg_chan_list_event()
when driver boots, at that time these two arguments are not determined
yet, hence by default pass WMI_VDEV_TYPE_UNSPEC and
IEEE80211_REG_UNSET_AP, this results in WMI_REG_INDOOR_AP being chosen
at last. In upcoming patches the rules would be updated when these two
arguments could be determined.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-4-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently we pass intersect flag to tell ath12k_reg_build_regd() whether
regulatory rulse are intersected. This flag is determined in
ath12k_reg_handle_chan_list() and has no other users.
Move related logic into ath12k_reg_build_regd() to make code clear. Also
relocate ath12k_reg_is_world_alpha() to avoid forward declaration, and
refine it for code simplicity.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-3-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ath12k_reg_chan_list_event() is doing quite some work: allocate/free
reg_info, parse chan list event and store required info in reg_info,
process reg_info, build regd and queue work item for later processing
etc, which makes it hard to read.
Refactor this function:
1. extract reg_info processing and regd building into a new helper
ath12k_reg_handle_chan_list().
2. extract reg_info free into a new helper ath12k_reg_reset_reg_info().
Note the refactor also benefit some upcoming patches where these helpers
are getting called.
Also relocate these two helpers and the existing
ath12k_reg_is_world_alpha() to reg.c to reflect what they are doing.
And update fw to firmware while relocating.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-2-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
spin_lock/spin_unlock are used in ath12k_reg_chan_list_event
to acquire/release ab->base_lock. For now this is safe because
that function is only called in soft IRQ context.
But ath12k_reg_chan_list_event() will be called from process
context in an upcoming patch, and this can result in a deadlock
if ab->base_lock is acquired in process context and then soft
IRQ occurs on the same CPU and tries to acquire that lock.
Fix it by using spin_lock_bh and spin_unlock_bh instead.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-1-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently mon reap timer is not used, and it is not needed anymore for
WCN7850.
So remove related code.
This change does not affect QCN9274, as the mon reap timer is not used
for QCN9274.
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250416022011.1935-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add debugfs support to simulate firmware crash to test firmware restart.
Usage:
-----
echo assert > /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/simulate_fw_crash
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250417065237.2507613-1-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Now some chips which support 'support_dual_stations' will enable DBS,
but will disable DFS. Restructure the ath11k_mac_setup_iface_combinations
function to support DBS and DFS compatibility.
About 'support_dual_station' feature can refer:
https://msgid.link/20230714023801.2621802-2-quic_cjhuang@quicinc.com
Add a ieee80211_iface_combination to support DBS and DFS compatibility,
one combination can support DFS(same with non dual sta), another
combination can support DBS. When running different scenarios that will
use different ieee80211_iface_combination due to mac80211 will go through
all of possible interface combinations.
In addition, maximum number of interfaces of these types should be total
allowed in this group.
The chips affected are:
QCA6390 hw2.0
WCN6855 hw2.0
WCN6855 hw2.1
Other chips are not affected.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-00410-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04402-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Link: https://patch.msgid.link/20241127022742.4016870-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the missing memory barrier to make sure that the REO dest ring
descriptor is read after the head pointer to avoid using stale data on
weakly ordered architectures like aarch64.
This may fix the ring-buffer corruption worked around by commit
f9fff67d2d7c ("wifi: ath11k: Fix SKB corruption in REO destination
ring") by silently discarding data, and may possibly also address user
reported errors like:
ath11k_pci 0006:01:00.0: msdu_done bit in attention is not set
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218005
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Link: https://patch.msgid.link/20250321145302.4775-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Users of the Lenovo ThinkPad X13s have reported that Wi-Fi sometimes
breaks and the log fills up with errors like:
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1484, expected 1492
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1460, expected 1484
which based on a quick look at the driver seemed to indicate some kind
of ring-buffer corruption.
Miaoqing Pan tracked it down to the host seeing the updated destination
ring head pointer before the updated descriptor, and the error handling
for that in turn leaves the ring buffer in an inconsistent state.
Add the missing memory barrier to make sure that the descriptor is read
after the head pointer to address the root cause of the corruption while
fixing up the error handling in case there are ever any (ordering) bugs
on the device side.
Note that the READ_ONCE() are only needed to avoid compiler mischief in
case the ring-buffer helpers are ever inlined.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218623
Link: https://lore.kernel.org/20250310010217.3845141-3-quic_miaoqing@quicinc.com
Cc: Miaoqing Pan <quic_miaoqing@quicinc.com>
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Link: https://patch.msgid.link/20250321094916.19098-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Firmware requests 2 segments at first. The first segment is of 6799360
whose allocation fails due to dma remapping not available. The success
is returned to firmware. Then firmware asks for 22 smaller segments
instead of 2 big ones. Those get allocated successfully. At suspend/
hibernation time, these segments aren't freed as they will be reused
by firmware after resuming.
After resuming, the firmware asks for the 2 segments again with the
first segment of 6799360 size. Since chunk->vaddr is not NULL, the
type and size are compared with the previous type and size to know if
it can be reused or not. Unfortunately, it is detected that it cannot
be reused and this first smaller segment is freed. Then we continue to
allocate 6799360 size memory which fails and ath11k_qmi_free_target_mem_chunk()
is called which frees the second smaller segment as well. Later success
is returned to firmware which asks for 22 smaller segments again. But
as we had freed 2 segments already, we'll allocate the first 2 new
smaller segments again and reuse the remaining 20. Hence 20 small
segments are being reused instead of 22.
Add skip logic when vaddr is set, but size/type don't match. Use the
same skip and success logic as used when dma_alloc_coherent() fails.
By skipping, the possibility of resume failure due to kernel failing to
allocate memory for QMI can be avoided.
kernel: ath11k_pci 0000:03:00.0: failed to allocate dma memory for qmi (524288 B type 1)
ath11k_pci 0000:03:00.0: failed to allocate qmi target memory: -22
Tested-on: WCN6855 WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.6
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250428080242.466901-1-usama.anjum@collabora.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Simplifies probe slightly and adds extra error codes.
Switching from devm_ioremap to the platform variant ends up calling
devm_request_mem_region, which reserves the memory region for the
various wmacs. Per board, there is only one wmac and after some fairly
thorough analysis, there are no overlapping memory regions between wmacs
and other devices on the ahb.
Tested on a TP-Link Archer C7v2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250421040044.44887-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Structures defined in hw.c are not modified in this driver.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
10357 951 0 11308 2c2c drivers/net/wireless/ath/ath10k/hw.o
After:
=====
text data bss dec hex filename
11125 203 0 11328 2c40 drivers/net/wireless/ath/ath10k/hw.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/504b4d5276d13f5f9c3bffcfdaf244006312c22b.1745051315.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
There is a spelling mistake in a ath10k_warn message. Fix it and
remove space before colon to tidy up message.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20250418115627.534833-1-colin.i.king@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
According to the code documentation in ath12k_mac_op_hw_scan(), "if no
links of an ML VIF are already active on the radio corresponding to the
given scan frequency, the scan link (link ID 15) should be used". This rule
should apply to non-ML interfaces as well to maintain uniformity across the
driver. However, currently, link 0 is selected as the scan link during
non-ML operations.
Update the code to use scan link ID 15 in all cases.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250417-fix_scan_vdev_handling-v3-2-9ec42513d26b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
For scanning purposes, the driver can use link ID 15 (scan link). A future
change will make non-ML interfaces to select the scan link. In this
scenario, arvif->link_id will be used to retrieve the link configuration in
ath12k_mac_vdev_create(). However, link ID 15 is not recognized as a valid
link ID in the upper kernel, which will result in a failure to fetch
link_conf and subsequently cause the scan to fail.
To avoid this issue, ensure link_conf is fetched only when the link ID is
within the valid range. Since link_conf cannot be retrieved using the scan
link, use vif->addr as the Ethernet address for creating the scan vdev.
This address will serve as the source address (address 2) in the probe
request frames during scanning. Additionally, use the automatic Tx power
value for the vdev. As this is a scan vdev, these values do not affect the
scan functionality.
Note that vif->addr will only be taken when a valid link_conf can not be
fetched. Otherwise, link_conf's address will be taken as address 2.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250417-fix_scan_vdev_handling-v3-1-9ec42513d26b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Read the country code from SMBIOS and send it to the firmware. The
firmware will then indicate the regulatory domain information for
the country code, which ath12k will use.
dmesg:
[ 1242.637253] ath12k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath12k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath12k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.927543] ath12k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-02582-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250417024227.1712-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Ping-Ke Shih says:
==================
rtw-next patches for v6.16
Some fixes and refinements across drivers, and regular development of
MLO and STA + P2P concurrency. Major changes are listed below.
rtw88:
* improve throughput for RTL8814AU
rtw89:
* support MLO
* improve user experience for STA + P2P concurrency
* dynamic antenna gain (DAG) with different power by antenna
* load SAR tables from ACPI
==================
Link: https://patch.msgid.link/17e74675-70cc-43d7-a797-afb937030d34@RTEXMBS04.realtek.com.tw/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The scan delay unit of firmware command for WiFi 6 chips is
microsecond, but is wrong set now and lead to abnormal work
for net-detect. Correct the unit to avoid the error.
Fixes: e99dd80c8a18 ("wifi: rtw89: wow: add delay option for net-detect")
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250513125203.6858-1-pkshih@realtek.com
|
|
Set the size to 6 instead of 2, since 'para' array is passed to
'rtw_fw_bt_wifi_control(rtwdev, para[0], ¶[1])', which reads
5 bytes:
void rtw_fw_bt_wifi_control(struct rtw_dev *rtwdev, u8 op_code, u8 *data)
{
...
SET_BT_WIFI_CONTROL_DATA1(h2c_pkt, *data);
SET_BT_WIFI_CONTROL_DATA2(h2c_pkt, *(data + 1));
...
SET_BT_WIFI_CONTROL_DATA5(h2c_pkt, *(data + 4));
Detected using the static analysis tool - Svace.
Fixes: 4136214f7c46 ("rtw88: add BT co-existence support")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250513121304.124141-1-aleksei.kodanev@bell-sw.com
|
|
MCC will track the changes of beacon offset, and trigger a recalculation
when the difference is larger than the tolerance. It means that a better
pattern is expected after recalculating. However, in the cases which get
a worse beacon offset, there is no chance to improve the pattern even if
recalculating. So, bypass them.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-7-pkshih@realtek.com
|
|
Originally, MCC just took periodic NoA into account. When the connected GO
announces non-periodic NoA and GC side is during MCC, sometimes GC cannot
receive beacons well if the MCC scheduling conflicts with the non-periodic
NoA planning. After the loss exceeds the tolerable amount, beacon filter
will report connection loss. However, in this case, the loss is acceptable.
So now, MCC will calculate the range of non-periodic NoA. And then, don't
care beacon loss during the range.
Besides, rtw89_mcc_fill_role_limit() only makes sense for GC. Remove the
redundant check of GO.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-6-pkshih@realtek.com
|
|
In the cases that two MCC roles' TBTTs are too close or too far, original
MCC pattern calculation logic will lead to a result that both roles might
not cover its TBTT with sufficient time. Introduce a new calculation logic
called anchor pattern for these corner cases. It allows to choose one role
as anchor to put its TBTT in the middle of its duration directly. For now,
a P2P role has a higher priority to be chosen as an anchor. Then, if able,
another role might need to depend on courtesy mechanism to take time from
anchor.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-5-pkshih@realtek.com
|
|
In one enablement of courtesy mechanism, there is one provider and
one receiver. And, receiver can use the provider's time in a given
period. But, to make P2P NoA protocol work as expected as possible,
GO should be present at the time it doesn't announce absent, and GC
should not use the time when GO announces absent. So, don't enable
courtesy mechanism if provider is GO or receiver is GC.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-4-pkshih@realtek.com
|
|
When MCC is about to stop, there may be some chanctx changes which are
queued for work but have not yet been run. To avoid these changes from
being processed in a wrong state (e.g. next new MCC instance), cancel
the queued work and drop queued changes.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-3-pkshih@realtek.com
|
|
When stopping MCC, FW can stop at a given MCC role following H2C command.
When pausing chanctx during MCC, in general, the caller expects to process
things with its chanctx. So, pass the caller as target and let FW stop MCC
at it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-2-pkshih@realtek.com
|
|
All the USB devices have a problem in AP mode: uploading the updated
beacon to the chip's reserved page can randomly fail:
[34996.474304] rtw88_8723du 1-2:1.2: error beacon valid
[34996.474788] rtw88_8723du 1-2:1.2: failed to download drv rsvd page
[34999.956369] rtw88_8723du 1-2:1.2: error beacon valid
[34999.956846] rtw88_8723du 1-2:1.2: failed to download drv rsvd page
[34999.956855] rtw88_8723du 1-2:1.2: failed to download beacon
[35017.978296] rtw88_8723du 1-2:1.2: error beacon valid
[35017.978805] rtw88_8723du 1-2:1.2: failed to download drv rsvd page
[35017.978823] rtw88_8723du 1-2:1.2: failed to download beacon
[35023.200395] rtw88_8723du 1-2:1.2: error beacon valid
[35023.200869] rtw88_8723du 1-2:1.2: failed to download drv rsvd page
[35023.200875] rtw88_8723du 1-2:1.2: failed to download beacon
[35478.680547] rtw88_8723du 1-2:1.2: error beacon valid
[35478.681023] rtw88_8723du 1-2:1.2: failed to download drv rsvd page
Disable some beacon-related hardware functions before uploading the
beacon and enable them again after.
Tested with RTL8723DU, RTL8812BU, RTL8822CE.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/c248c40a-d432-47ed-90e0-d81ee6c32464@gmail.com
|
|
RTL8811AU stops responding during the firmware download on some systems:
[ 809.256440] rtw_8821au 5-2.1:1.0: Firmware version 42.4.0, H2C version 0
[ 812.759142] rtw_8821au 5-2.1:1.0 wlp48s0f4u2u1: renamed from wlan0
[ 837.315388] rtw_8821au 1-4:1.0: write register 0x1ef4 failed with -110
[ 867.524259] rtw_8821au 1-4:1.0: write register 0x1ef8 failed with -110
[ 868.930976] rtw_8821au 5-2.1:1.0 wlp48s0f4u2u1: entered promiscuous mode
[ 897.730952] rtw_8821au 1-4:1.0: write register 0x1efc failed with -110
Maybe it takes too long when writing the firmware 4 bytes at a time.
Write 196 bytes at a time for RTL8821AU, RTL8811AU, and RTL8812AU,
and 254 bytes at a time for RTL8723DU. These are the sizes used in
their official drivers. Tested with all these chips.
Cc: stable@vger.kernel.org
Link: https://github.com/lwfinger/rtw88/issues/344
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/43f1daad-3ec0-4a3b-a50c-9cd9eb2c2f52@gmail.com
|
|
RTL8811AU stops responding during the firmware download on some systems:
[ 809.256440] rtw_8821au 5-2.1:1.0: Firmware version 42.4.0, H2C version 0
[ 812.759142] rtw_8821au 5-2.1:1.0 wlp48s0f4u2u1: renamed from wlan0
[ 837.315388] rtw_8821au 1-4:1.0: write register 0x1ef4 failed with -110
[ 867.524259] rtw_8821au 1-4:1.0: write register 0x1ef8 failed with -110
[ 868.930976] rtw_8821au 5-2.1:1.0 wlp48s0f4u2u1: entered promiscuous mode
[ 897.730952] rtw_8821au 1-4:1.0: write register 0x1efc failed with -110
Each write takes 30 seconds to fail because that's the timeout currently
used for control messages in rtw_usb_write().
In this scenario the firmware download takes at least 2000 seconds.
Because this is done from the USB probe function, the long delay makes
other things in the system hang.
Reduce the timeout to 500 ms. This is the value used by the official USB
wifi drivers from Realtek.
Of course this only makes things hang for ~30 seconds instead of ~30
minutes. It doesn't fix the firmware download.
Tested with RTL8822CU, RTL8812BU, RTL8811CU, RTL8814AU, RTL8811AU,
RTL8812AU, RTL8821AU, RTL8723DU.
Cc: stable@vger.kernel.org
Fixes: a82dfd33d123 ("wifi: rtw88: Add common USB chip support")
Link: https://github.com/lwfinger/rtw88/issues/344
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1e35dd26-3f10-40b1-b2b4-f72184a26611@gmail.com
|
|
RX tag is sequence number to ensure RX DMA is complete. On platform
Gigabyte X870 AORUS ELITE WIFI7, sometimes it needs longer retry times
to complete RX DMA, or driver throws warnings and connection drops:
rtw89_8922ae 0000:07:00.0: failed to update 162 RXBD info: -11
rtw89_8922ae 0000:07:00.0: failed to update 163 RXBD info: -11
rtw89_8922ae 0000:07:00.0: failed to update 32 RXBD info: -11
rtw89_8922ae 0000:07:00.0: failed to release TX skbs
Fixes: 0bc7d1d4e63c ("wifi: rtw89: pci: validate RX tag for RXQ and RPQ")
Reported-by: Samuel Reyes <zohrlaffz@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/f4355539f3ac46bbaf9c586d059a8cbb@realtek.com/T/#t
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250509013433.7573-1-pkshih@realtek.com
|
|
Due to mac80211 triggering the hardware to enter idle mode, it fails
to install WEP key causing connected station can't ping successfully.
Currently, it forces the hardware to leave idle mode before driver
adding WEP keys.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250507031203.8256-1-pkshih@realtek.com
|
|
To support 36-bit DMA, configure chip proprietary bit via PCI config API
or chip DBI interface. However, the PCI device mmap isn't set yet and
the DBI is also inaccessible via mmap, so only if the bit can be accessible
via PCI config API, chip can support 36-bit DMA. Otherwise, fallback to
32-bit DMA.
With NULL mmap address, kernel throws trace:
BUG: unable to handle page fault for address: 0000000000001090
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 1 UID: 0 PID: 71 Comm: irq/26-pciehp Tainted: G OE 6.14.2-061402-generic #202504101348
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
RIP: 0010:rtw89_pci_ops_write16+0x12/0x30 [rtw89_pci]
RSP: 0018:ffffb0ffc0acf9d8 EFLAGS: 00010206
RAX: ffffffffc158f9c0 RBX: ffff94865e702020 RCX: 0000000000000000
RDX: 0000000000000718 RSI: 0000000000001090 RDI: ffff94865e702020
RBP: ffffb0ffc0acf9d8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000015
R13: 0000000000000719 R14: ffffb0ffc0acfa1f R15: ffffffffc1813060
FS: 0000000000000000(0000) GS:ffff9486f3480000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000001090 CR3: 0000000090440001 CR4: 00000000000626f0
Call Trace:
<TASK>
rtw89_pci_read_config_byte+0x6d/0x120 [rtw89_pci]
rtw89_pci_cfg_dac+0x5b/0xb0 [rtw89_pci]
rtw89_pci_probe+0xa96/0xbd0 [rtw89_pci]
? __pfx___device_attach_driver+0x10/0x10
? __pfx___device_attach_driver+0x10/0x10
local_pci_probe+0x47/0xa0
pci_call_probe+0x5d/0x190
pci_device_probe+0xa7/0x160
really_probe+0xf9/0x370
? pm_runtime_barrier+0x55/0xa0
__driver_probe_device+0x8c/0x140
driver_probe_device+0x24/0xd0
__device_attach_driver+0xcd/0x170
bus_for_each_drv+0x99/0x100
__device_attach+0xb4/0x1d0
device_attach+0x10/0x20
pci_bus_add_device+0x59/0x90
pci_bus_add_devices+0x31/0x80
pciehp_configure_device+0xaa/0x170
pciehp_enable_slot+0xd6/0x240
pciehp_handle_presence_or_link_change+0xf1/0x180
pciehp_ist+0x162/0x1c0
irq_thread_fn+0x24/0x70
irq_thread+0xef/0x1c0
? __pfx_irq_thread_fn+0x10/0x10
? __pfx_irq_thread_dtor+0x10/0x10
? __pfx_irq_thread+0x10/0x10
kthread+0xfc/0x230
? __pfx_kthread+0x10/0x10
ret_from_fork+0x47/0x70
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 1fd4b3fe52ef ("wifi: rtw89: pci: support 36-bit PCI DMA address")
Reported-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/ccaf49b6-ff41-4917-90f1-f53cadaaa0da@gmail.com/T/#u
Closes: https://github.com/openwrt/openwrt/issues/17025
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250506015356.7995-1-pkshih@realtek.com
|
|
Cross-merge networking fixes after downstream PR (net-6.15-rc7).
Conflicts:
tools/testing/selftests/drivers/net/hw/ncdevmem.c
97c4e094a4b2 ("tests/ncdevmem: Fix double-free of queue array")
2f1a805f32ba ("selftests: ncdevmem: Implement devmem TCP TX")
https://lore.kernel.org/20250514122900.1e77d62d@canb.auug.org.au
Adjacent changes:
net/core/devmem.c
net/core/devmem.h
0afc44d8cdf6 ("net: devmem: fix kernel panic when netlink socket close after module unload")
bd61848900bf ("net: devmem: Implement TX path")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
iwlwifi features, notably a rework of the transport configuration
====================
Link: https://patch.msgid.link/MW5PR11MB5810DD2655DE461E98A618DDA390A@MW5PR11MB5810.namprd11.prod.outlook.com/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Ensure that the hdr_trans_tlv command is included in the broadcast wtbl to
prevent the IPv6 and multicast packet from being dropped by the chip.
Cc: stable@vger.kernel.org
Fixes: cb1353ef3473 ("wifi: mt76: mt7925: integrate *mlo_sta_cmd and *sta_cmd")
Reported-by: Benjamin Xiao <fossben@pm.me>
Tested-by: Niklas Schnelle <niks@kernel.org>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://lore.kernel.org/lkml/EmWnO5b-acRH1TXbGnkx41eJw654vmCR-8_xMBaPMwexCnfkvKCdlU5u19CGbaapJ3KRu-l3B-tSUhf8CCQwL0odjo6Cd5YG5lvNeB-vfdg=@pm.me/
Link: https://patch.msgid.link/20250509010421.403022-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
A warning on driver removal started occurring after commit 9dd05df8403b
("net: warn if NAPI instance wasn't shut down"). Disable tx napi before
deleting it in mt76_dma_cleanup().
WARNING: CPU: 4 PID: 18828 at net/core/dev.c:7288 __netif_napi_del_locked+0xf0/0x100
CPU: 4 UID: 0 PID: 18828 Comm: modprobe Not tainted 6.15.0-rc4 #4 PREEMPT(lazy)
Hardware name: ASUS System Product Name/PRIME X670E-PRO WIFI, BIOS 3035 09/05/2024
RIP: 0010:__netif_napi_del_locked+0xf0/0x100
Call Trace:
<TASK>
mt76_dma_cleanup+0x54/0x2f0 [mt76]
mt7921_pci_remove+0xd5/0x190 [mt7921e]
pci_device_remove+0x47/0xc0
device_release_driver_internal+0x19e/0x200
driver_detach+0x48/0x90
bus_remove_driver+0x6d/0xf0
pci_unregister_driver+0x2e/0xb0
__do_sys_delete_module.isra.0+0x197/0x2e0
do_syscall_64+0x7b/0x160
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Tested with mt7921e but the same pattern can be actually applied to other
mt76 drivers calling mt76_dma_cleanup() during removal. Tx napi is enabled
in their *_dma_init() functions and only toggled off and on again inside
their suspend/resume/reset paths. So it should be okay to disable tx
napi in such a generic way.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 2ac515a5d74f ("mt76: mt76x02: use napi polling for tx cleanup")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Tested-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250506115540.19045-1-pchelkin@ispras.ru
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
In the current code, if an ROC is started on a vif that already has an
active ROC we reject it and warn.
But really there is no such limitation. The actual limitation is to not
have 2 ROCs of the same type simultaneously.
Add a helper function to find a vif that has an active ROC of a given
type, and only if one exist - reject the ROC.
This allows also to remove bss_roc_vif.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.1f8c55198578.I17cb191596ed4e97a4854108f8ca5ca197662a62@changeid
|
|
Various headers are required for these to build properly.
Include the needed files.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.956281013349.I4c537dffb82f5e5042e4a880cde3c6da38a56cbc@changeid
|
|
Context info was introduced in 22000, and was significantly changed in
ax210. The new version of context info was called 'gen3',
probably because in 22000, the gen2 transport was added.
But this name is just wrong:
- if 'gen' enumerates transports, there was not a gen3 transport, just a
few modifications to gen1/2 transports needed for ax210.
- if 'gen' enumerates devices, then we can just use the device names.
Also, context info will soon become a lib, agnostic of the transport
generations.
Simply replace 'gen3' with 'v2'.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.a580bd8d4f74.Ie413a02233f1a5ad538e13071c09760b9d97be3b@changeid
|
|
iwl_pcie_apply_destination is used in all generation.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.7eaf79a07226.I615cfd21001208b366c94a5fcb8e30a7d97f0ac2@changeid
|
|
Map iwl_context_info to the matching struct in the FW.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.a7240935006e.I75e2e13421b5dac2c1bdbd01fdfd34c38f2d3d8c@changeid
|
|
TFD_QUEUE_SIZE_MAX_GEN3 is not used, remove it.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.a0154cca6afb.Ifb4915e0acd51be6a75d33a8b96b3f7b0928b312@changeid
|
|
As those are now the same, unify and adjust the documentation.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.b7ddfade8fec.I2bf97252c4bd751077ade204767eed02d815614d@changeid
|
|
iwlagn_scd_bc_tbl is used for pre-ax210 devices,
and iwl_gen3_bc_tbl_entry is used for ax210 and on. But there is no
difference between the the 22000 version and the AX210+ one.
In order to unify the two, as first step make iwlagn_scd_bc_tbl an entry
as well, and adjust the code. In a later patch both structures will be
unified.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.645cd82ebf48.Iaa7e88179372d60ef31157e379737b5babe54012@changeid
|
|
'GEN3' here really means 'AX210'. Rename.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.b7fb5b854ded.Ib52b84c6e36e312b2eeb84a3cf71c6185fb52ee7@changeid
|
|
We have iwl_tx_cmd for devices older than 22000, iwl_tx_cmd_gen2 for
22000 devices, and iwl_tx_cmd_gen3 ax210 and up.
But the convention for all other APIs is to have the latest version
without any prefix and the older ones - with a _vX prefix,
where X is the highest version that this struct support.
The term 'gen' was introduced as the name of the (back then) new
transport, and should not be used as a device name (for that we have the
actual names: 22000, ax210, etc.)
Now as a new transport, called 'gen3', is going to be written and it can
be confused with this API.
Move iwl_tx_cmd to use the regular versioning convention.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.806e40c8f767.Ibc0e95e43a6fa6d47f72823bf804314d5db84618@changeid
|
|
This version is not used on any device. Don't support it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
We don't need the CORES() match nor jacket (which really doesn't
even make sense to match to the RF anyway), and since the subdevice
masks we care about are contiguous, we can encode them as highest
and lowest bit set (automatically.) By encoding whether to match or
not as separate flags and taking advantage of the limited range of
the RF type, step and ID we can reduce the amount of memory needed
for the table, while also making the logic (apart perhaps from the
subdevice mask) easier to understand.
This reduces the size of the module by about 1.5KiB on x86-64.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.38a805a7c96f.Ieece00476cea6054b0827cd075eb8ba5943373df@changeid
|
