| Age | Commit message (Collapse) | Author |
|---|
|
Through using phylib's EEE state, priv->tx_lpi_enabled has become a
write-only variable. Remove it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZE1-0002KS-K1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
stmmac_disable_eee_mode() is now only called from stmmac_xmit() when
both priv->tx_path_in_lpi_mode and priv->eee_sw_timer_en are true.
Therefore:
if (!priv->eee_sw_timer_en)
in stmmac_disable_eee_mode() will never be true, so this is dead code.
Remove it, and rename the function to indicate that it now only deals
with software based EEE mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDw-0002KL-Gg@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Setting edata->tx_lpi_enabled in stmmac_ethtool_op_get_eee() gets
overwritten by phylib, so there's no point setting this.
In stmmac_ethtool_op_set_eee(), now that stmmac is using the result of
phylib's evaluation of EEE, there is no need to handle anything in the
ethtool EEE ops other than calling through to the appropriate phylink
function, which will pass on to phylib the users request.
As stmmac_disable_eee_mode() is now no longer called from outside
stmmac_main.c, make it static.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDr-0002KF-Cv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make stmmac EEE depend on phylib's evaluation of user settings and PHY
negotiation, as indicated by phy->enable_tx_lpi. This will ensure when
phylib has evaluated that the user has disabled LPI, phy_init_eee()
will not be called, and priv->eee_active will be false, causing LPI/EEE
to be disabled.
This is an interim measure - phy_init_eee() will be removed in a later
patch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDm-0002K9-9w@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since eee_timer is used to initialise priv->tx_lpi_timer, this also
should be unsigned to avoid a negative number being interpreted as a
very large positive number. Note that this makes the check for negative
numbers passed in as a module parameter redundant, and passing a
negative number will now produce a large delay rather than the
default. Since the default is used without an argument, passing a
negative number would be quite obscure. However, if users do, then
this will need to be revisited.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDh-0002K3-6y@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ethtool interface uses u32 for tx_lpi_timer, and so does phylib.
Use u32 to store this internally within stmmac rather than "int"
which could misinterpret large values.
Correct "value" in dwmac4_set_eee_lpi_entry_timer() to use u32
rather than int, which is derived from tx_lpi_timer. Even though this
path won't be used with values larger than STMMAC_ET_MAX, this brings
consistency of type usage to the stmmac code for this variable.
We leave eee_timer unchanged for now, with the assumption that values
up to INT_MAX will safely fit in a u32.
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDc-0002Jx-3b@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When stmmac_ethtool_op_get_eee() is called, stmmac sets the tx_lpi_timer
and tx_lpi_enabled members, and then calls into phylink and thus phylib.
phylib overwrites these members.
phylib will also cause a link down/link up transition when settings
that impact the MAC have been changed.
Convert stmmac to use the tx_lpi_timer setting in struct phy_device,
updating priv->tx_lpi_timer each time when the link comes up, rather
than trying to maintain this user setting itself. We initialise the
phylib tx_lpi_timer setting by doing a get_ee-modify-set_eee sequence
with the last known priv->tx_lpi_timer value. In order for this to work
correctly, we also need this member to be initialised earlier.
As stmmac_eee_init() is no longer called outside of stmmac_main.c, make
it static.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDW-0002Jr-W3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a function to allow configuration of the PCS's clock stop enable
bit, used to configure whether the xMII receive clock can be stopped
during LPI mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDR-0002Jl-Ry@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In 'ath9k_hw_get_nf_hist_mid()', prefer 'memcpy()' and 'sort()'
over an ad-hoc things. Briefly tested as a separate module.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250109080703.106692-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request pdev puncture stats from firmware through
HTT stats type 46. These stats give the count of number of
subbands used in different wifi standards.
Sample output:
-------------
echo 46 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
tx_ofdm_su_last_used_pattern_mask = 0x00000001
tx_ofdm_su_num_subbands_used_cnt_01 = 217
tx_ofdm_su_num_subbands_used_cnt_02 = 0
tx_ofdm_su_num_subbands_used_cnt_03 = 0
.....
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
tx_ax_dl_mu_ofdma_last_used_pattern_mask = 0x00000000
tx_ax_dl_mu_ofdma_num_subbands_used_cnt_01 = 0
tx_ax_dl_mu_ofdma_num_subbands_used_cnt_02 = 0
tx_ax_dl_mu_ofdma_num_subbands_used_cnt_03 = 0
.....
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
tx_be_dl_mu_ofdma_last_used_pattern_mask = 0x00000000
tx_be_dl_mu_ofdma_num_subbands_used_cnt_01 = 0
tx_be_dl_mu_ofdma_num_subbands_used_cnt_02 = 0
tx_be_dl_mu_ofdma_num_subbands_used_cnt_03 = 0
.....
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
rx_ax_ul_mu_ofdma_last_used_pattern_mask = 0x00000000
rx_ax_ul_mu_ofdma_num_subbands_used_cnt_01 = 0
rx_ax_ul_mu_ofdma_num_subbands_used_cnt_02 = 0
rx_ax_ul_mu_ofdma_num_subbands_used_cnt_03 = 0
.....
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
rx_be_ul_mu_ofdma_last_used_pattern_mask = 0x00000000
rx_be_ul_mu_ofdma_num_subbands_used_cnt_01 = 0
rx_be_ul_mu_ofdma_num_subbands_used_cnt_02 = 0
rx_be_ul_mu_ofdma_num_subbands_used_cnt_03 = 0
.....
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218035711.2573584-3-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request Address Search Table(AST) entries stats
from firmware through HTT stats type 41. These stats give AST entries
related information such as software peer id, MAC address, pdev id,
vdev, id, next hop, etc.
Sample output:
-------------
echo 41 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_AST_ENTRY_TLV:
ast_index = 10
mac_addr = 00:00:00:01:00:00
sw_peer_id = 0
pdev_id = 3
vdev_id = 255
next_hop = 0
mcast = 0
monitor_direct = 0
mesh_sta = 0
mec = 0
intra_bss = 0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218035711.2573584-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request OFDMA stats of transmit buffers from firmware through
HTT stats type 32. These stats give information about NDPA, NDP, BRP and
steering mechanisms.
Note: WCN7850 firmware version -
WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 does not
support HTT stats type 32.
Sample output:
-------------
echo 32 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_TXBF_OFDMA_AX_NDPA_STATS_TLV:
ax_ofdma_ndpa_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
ax_ofdma_ndpa_tried = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
.....
HTT_TXBF_OFDMA_AX_NDP_STATS_TLV:
ax_ofdma_ndp_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
ax_ofdma_ndp_tried = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
.....
HTT_TXBF_OFDMA_AX_BRP_STATS_TLV:
ax_ofdma_brpoll_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
ax_ofdma_brpoll_tied = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
.....
HTT_TXBF_OFDMA_AX_STEER_STATS_TLV:
ax_ofdma_num_ppdu_steer = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
ax_ofdma_num_usrs_prefetch = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
.....
HTT_TXBF_OFDMA_AX_STEER_MPDU_STATS_TLV:
rbo_steer_mpdus_tried = 0
rbo_steer_mpdus_failed = 0
sifs_steer_mpdus_tried = 0
sifs_steer_mpdus_failed = 0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org>
Link: https://patch.msgid.link/20241128110949.3672364-3-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request transmit rate buffer stats from firmware through
HTT stats type 31. These stats give information such as MCS, NSS and
bandwidth of transmit and input buffer.
Sample output:
-------------
echo 31 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_STATS_PDEV_TX_RATE_TXBF_STATS:
Legacy OFDM Rates: 6 Mbps: 0, 9 Mbps: 0, 12 Mbps: 0, 18 Mbps: 0
24 Mbps: 0, 36 Mbps: 0, 48 Mbps: 0, 54 Mbps: 0
tx_ol_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0
tx_ibf_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0
tx_txbf_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0
tx_ol_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0
tx_ibf_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0
tx_txbf_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0
tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0
half_tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0
quarter_tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0
tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
half_tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
quarter_tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
half_tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
quarter_tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
HTT_STATS_PDEV_TXBF_FLAG_RETURN_STATS:
TXBF_reason_code_stats: 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jjohnson@kernel.org>
Link: https://patch.msgid.link/20241128110949.3672364-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Running 'scripts/kernel-doc -Wall -Werror -none' flagged the following
kernel-doc issues:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:823: warning: No description found for return value of 'brcmf_apsta_add_vif'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:907: warning: No description found for return value of 'brcmf_mon_add_vif'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:7419: warning: No description found for return value of 'brcmf_setup_ifmodes'
Add the missing 'Return:' tags to the kernel-doc of these functions.
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250106-brcmfmac-kdoc-v1-1-ed72196e21a1@oss.qualcomm.com
|
|
THe last use of il_get_single_channel_number() was removed in 2011 by
commit dd6d2a8aef69 ("iwlegacy: remove reset rf infrastructure")
when it was still called iwl_legacy_get_single_channel_number.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241226011355.135417-3-linux@treblig.org
|
|
The last use of il3945_calc_db_from_ratio() was removed in 2010 by
commit ed1b6e99b5e6 ("iwlwifi: remove noise reporting")
when it was still called iwl3945_calc_db_from_ratio().
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241226011355.135417-2-linux@treblig.org
|
|
The intention here is not clear but as this was already tested and matches
vendor driver it's better not to change behavior even if it looks suspicious.
So just remove the unused values.
Coverity-ID: 1525307
Signed-off-by: Ariel Otilibili <ariel.otilibili-anieli@eurecom.fr>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
[kvalo@kernel.org: write commit message]
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241221124445.1094460-2-ariel.otilibili-anieli@eurecom.fr
|
|
Somewhen between 6.10 and 6.11 the driver started to crash on my
MacBookPro14,3. The property doesn't exist and 'tmp' remains
uninitialized, so we pass a random pointer to devm_kstrdup().
The crash I am getting looks like this:
BUG: unable to handle page fault for address: 00007f033c669379
PF: supervisor read access in kernel mode
PF: error_code(0x0001) - permissions violation
PGD 8000000101341067 P4D 8000000101341067 PUD 101340067 PMD 1013bb067 PTE 800000010aee9025
Oops: Oops: 0001 [#1] SMP PTI
CPU: 4 UID: 0 PID: 827 Comm: (udev-worker) Not tainted 6.11.8-gentoo #1
Hardware name: Apple Inc. MacBookPro14,3/Mac-551B86E5744E2388, BIOS 529.140.2.0.0 06/23/2024
RIP: 0010:strlen+0x4/0x30
Code: f7 75 ec 31 c0 c3 cc cc cc cc 48 89 f8 c3 cc cc cc cc 0f 1f 40 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa <80> 3f 00 74 14 48 89 f8 48 83 c0 01 80 38 00 75 f7 48 29 f8 c3 cc
RSP: 0018:ffffb4aac0683ad8 EFLAGS: 00010202
RAX: 00000000ffffffea RBX: 00007f033c669379 RCX: 0000000000000001
RDX: 0000000000000cc0 RSI: 00007f033c669379 RDI: 00007f033c669379
RBP: 00000000ffffffea R08: 0000000000000000 R09: 00000000c0ba916a
R10: ffffffffffffffff R11: ffffffffb61ea260 R12: ffff91f7815b50c8
R13: 0000000000000cc0 R14: ffff91fafefffe30 R15: ffffb4aac0683b30
FS: 00007f033ccbe8c0(0000) GS:ffff91faeed00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f033c669379 CR3: 0000000107b1e004 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x149/0x4c0
? raw_spin_rq_lock_nested+0xe/0x20
? sched_balance_newidle+0x22b/0x3c0
? update_load_avg+0x78/0x770
? exc_page_fault+0x6f/0x150
? asm_exc_page_fault+0x26/0x30
? __pfx_pci_conf1_write+0x10/0x10
? strlen+0x4/0x30
devm_kstrdup+0x25/0x70
brcmf_of_probe+0x273/0x350 [brcmfmac]
Signed-off-by: Stefan Dösinger <stefan@codeweavers.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250106170958.3595-1-stefan@codeweavers.com
|
|
If firmware boot failes, runtime pm is put too often:
[12092.708099] wlcore: ERROR firmware boot failed despite 3 retries
[12092.708099] wl18xx_driver wl18xx.1.auto: Runtime PM usage count underflow!
Fix that by redirecting all error gotos before runtime_get so that runtime is
not put.
Fixes: c40aad28a3cf ("wlcore: Make sure firmware is initialized in wl1271_op_add_interface()")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Michael Nemanov <michael.nemanov@ti.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250104195507.402673-1-akemnade@kernel.org
|
|
There is a specific error path in probe functions in wilc drivers (both
sdio and spi) which can lead to kernel panic, as this one for example
when using SPI:
Unable to handle kernel paging request at virtual address 9f000000 when read
[9f000000] *pgd=00000000
Internal error: Oops: 5 [#1] ARM
Modules linked in: wilc1000_spi(+) crc_itu_t crc7 wilc1000 cfg80211 bluetooth ecdh_generic ecc
CPU: 0 UID: 0 PID: 106 Comm: modprobe Not tainted 6.13.0-rc3+ #22
Hardware name: Atmel SAMA5
PC is at wiphy_unregister+0x244/0xc40 [cfg80211]
LR is at wiphy_unregister+0x1c0/0xc40 [cfg80211]
[...]
wiphy_unregister [cfg80211] from wilc_netdev_cleanup+0x380/0x494 [wilc1000]
wilc_netdev_cleanup [wilc1000] from wilc_bus_probe+0x360/0x834 [wilc1000_spi]
wilc_bus_probe [wilc1000_spi] from spi_probe+0x15c/0x1d4
spi_probe from really_probe+0x270/0xb2c
really_probe from __driver_probe_device+0x1dc/0x4e8
__driver_probe_device from driver_probe_device+0x5c/0x140
driver_probe_device from __driver_attach+0x220/0x540
__driver_attach from bus_for_each_dev+0x13c/0x1a8
bus_for_each_dev from bus_add_driver+0x2a0/0x6a4
bus_add_driver from driver_register+0x27c/0x51c
driver_register from do_one_initcall+0xf8/0x564
do_one_initcall from do_init_module+0x2e4/0x82c
do_init_module from load_module+0x59a0/0x70c4
load_module from init_module_from_file+0x100/0x148
init_module_from_file from sys_finit_module+0x2fc/0x924
sys_finit_module from ret_fast_syscall+0x0/0x1c
The issue can easily be reproduced, for example by not wiring correctly
a wilc device through SPI (and so, make it unresponsive to early SPI
commands). It is due to a recent change decoupling wiphy allocation from
wiphy registration, however wilc_netdev_cleanup has not been updated
accordingly, letting it possibly call wiphy unregister on a wiphy which
has never been registered.
Fix this crash by moving wiphy_unregister/wiphy_free out of
wilc_netdev_cleanup, and by adjusting error paths in both drivers
Fixes: fbdf0c5248dc ("wifi: wilc1000: Register wiphy after reading out chipid")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241223-wilc_fix_probe_error_path-v1-1-91fa7bd8e5b6@bootlin.com
|
|
Setting beacon_int_min_gcd and NL80211_IFTYPE_ADHOC in the same interface
combination is invalid, which will trigger the following warning trace
and get error returned from wiphy_register().
[ 10.080325] Call trace:
[ 10.082761] wiphy_register+0xc4/0x76c [cfg80211]
[ 10.087465] ieee80211_register_hw+0x800/0xac4 [mac80211]
[ 10.092868] mt76_register_device+0x16c/0x2c0 [mt76]
[ 10.097829] mt7996_register_device+0x740/0x844 [mt7996e]
Fix this by removing unused adhoc iftype.
Fixes: 948f65249868 ("wifi: mt76: mt7996: advertize beacon_int_min_gcd")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241007135133.5336-1-shayne.chen@mediatek.com
|
|
Add support for CAN_CTRLMODE_BERR_REPORTING,
allowing Bus Error Reporting to be enabled or disabled.
Previously, Bus Error Reporting was always active.
Co-developed-by: Alison Below <alisonbelow@gmail.com>
Signed-off-by: Alison Below <alisonbelow@gmail.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20241230142645.128244-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Ensure statistics, error counters, and CAN state are updated consistently,
even when alloc_can_err_skb() fails during state changes or error message
frame reception.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20241230142645.128244-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for CAN_CTRLMODE_BERR_REPORTING,
allowing Bus Error Reporting to be enabled or disabled.
Previously, Bus Error Reporting was always active.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20241230142645.128244-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Ensure statistics, error counters, and CAN state are updated consistently,
even when alloc_can_err_skb() fails during state changes or error message
frame reception.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20241230142645.128244-1-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
m_can user like the tcan4x5x device, can go into standby mode.
Low power RX mode is enabled to allow wake on can.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20241122-tcan-standby-v3-3-90bafaf5eccd@geanix.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
At Vsup 12V, standby mode will save 7-8mA, when the interface is
down.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20241122-tcan-standby-v3-2-90bafaf5eccd@geanix.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is added in preparation for calling standby mode in the tcan4x5x
driver or other users of m_can.
For the tcan4x5x; If Vsup 12V, standby mode will save 7-8mA, when the
interface is down.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20241122-tcan-standby-v3-1-90bafaf5eccd@geanix.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
ipsec-next-2025-01-09
1) Implement the AGGFRAG protocol and basic IP-TFS (RFC9347) functionality.
From Christian Hopps.
2) Support ESN context update to hardware for TX.
From Jianbo Liu.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use helper phy_disable_eee() instead of setting phylib-internal bitmap
eee_broken_modes directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/5e19eebe-121e-4a41-b36d-a35631279dd8@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netconsole configfs helpers doesn't allow the creation of more than
MAX_USERDATA_ITEMS items.
Add a warning when netconsole userdata update function attempts sees
more than MAX_USERDATA_ITEMS entries.
Replace silent ignore mechanism with WARN_ON_ONCE() to highlight
potential misuse during development and debugging.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250108-netcons_overflow_test-v3-1-3d85eb091bec@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CPSW ALE has 75-bit ALE entries stored across three 32-bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions support
ALE field entries spanning up to two words at the most.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions work as
expected when ALE field spanned across word1 and word2, but fails when
ALE field spanned across word2 and word3.
For example, while reading the ALE field spanned across word2 and word3
(i.e. bits 62 to 64), the word3 data shifted to an incorrect position
due to the index becoming zero while flipping.
The same issue occurred when setting an ALE entry.
This issue has not been seen in practice but will be an issue in the future
if the driver supports accessing ALE fields spanning word2 and word3
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: b685f1a58956 ("net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()/cpsw_ale_set_field()")
Signed-off-by: Sudheer Kumar Doredla <s-doredla@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20250108172433.311694-1-s-doredla@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.13-rc7).
Conflicts:
a42d71e322a8 ("net_sched: sch_cake: Add drop reasons")
737d4d91d35b ("sched: sch_cake: add bounds checks to host bulk flow fairness counts")
Adjacent changes:
drivers/net/ethernet/meta/fbnic/fbnic.h
3a856ab34726 ("eth: fbnic: add IRQ reuse support")
95978931d55f ("eth: fbnic: Revert "eth: fbnic: Add hardware monitoring support via HWMON interface"")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RX adaptive interrupt moderation table is indexed by link speed
range, where the last row of the table is the catch-all for all link
speeds greater than 10Gbps. The comment said 10 - 40Gbps, but since
there are now adapters with link speeds than 40Gbps, the comment is now
wrong and should indicate it applies to all speeds greater than 10Gbps.
Co-developed-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Co-developed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20250107214159.18807-4-johndale@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The link speed is obtained in the RX adaptive coalescing function. It
was being called at probe time when the link may not be up. Change the
call to run after the Link comes up.
The impact of not getting the correct link speed was that the low end of
the adaptive interrupt range was always being set to 0 which could have
caused a slight increase in the number of RX interrupts.
Co-developed-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Co-developed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20250107214159.18807-3-johndale@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the function used for setting the RX coalescing range to before
the function that checks the link status. It needs to be called from
there instead of from the probe function.
There is no functional change.
Co-developed-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Co-developed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Link: https://patch.msgid.link/20250107214159.18807-2-johndale@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When cmd_alloc_index(), fails cmd_work_handler() needs
to complete ent->slotted before returning early.
Otherwise the task which issued the command may hang:
mlx5_core 0000:01:00.0: cmd_work_handler:877:(pid 3880418): failed to allocate command entry
INFO: task kworker/13:2:4055883 blocked for more than 120 seconds.
Not tainted 4.19.90-25.44.v2101.ky10.aarch64 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/13:2 D 0 4055883 2 0x00000228
Workqueue: events mlx5e_tx_dim_work [mlx5_core]
Call trace:
__switch_to+0xe8/0x150
__schedule+0x2a8/0x9b8
schedule+0x2c/0x88
schedule_timeout+0x204/0x478
wait_for_common+0x154/0x250
wait_for_completion+0x28/0x38
cmd_exec+0x7a0/0xa00 [mlx5_core]
mlx5_cmd_exec+0x54/0x80 [mlx5_core]
mlx5_core_modify_cq+0x6c/0x80 [mlx5_core]
mlx5_core_modify_cq_moderation+0xa0/0xb8 [mlx5_core]
mlx5e_tx_dim_work+0x54/0x68 [mlx5_core]
process_one_work+0x1b0/0x448
worker_thread+0x54/0x468
kthread+0x134/0x138
ret_from_fork+0x10/0x18
Fixes: 485d65e13571 ("net/mlx5: Add a timeout to acquire the command queue semaphore")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250108030009.68520-1-zhaochenguang@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pci_irq_vector() function never returns zero. It returns negative
error codes or a positive non-zero IRQ number. Fix the error checking to
test for negatives.
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/f2ecc88d-af13-4651-9820-7cc665230019@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nvidia's Tegra MGBE controllers require the IOMMU "Stream ID" (SID) to be
written to the MGBE_WRAP_AXI_ASID0_CTRL register.
The current driver is hard coded to use MGBE0's SID for all controllers.
This causes softirq time outs and kernel panics when using controllers
other than MGBE0.
Example dmesg errors when an ethernet cable is connected to MGBE1:
[ 116.133290] tegra-mgbe 6910000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 121.851283] tegra-mgbe 6910000.ethernet eth1: NETDEV WATCHDOG: CPU: 5: transmit queue 0 timed out 5690 ms
[ 121.851782] tegra-mgbe 6910000.ethernet eth1: Reset adapter.
[ 121.892464] tegra-mgbe 6910000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 121.905920] tegra-mgbe 6910000.ethernet eth1: PHY [stmmac-1:00] driver [Aquantia AQR113] (irq=171)
[ 121.907356] tegra-mgbe 6910000.ethernet eth1: Enabling Safety Features
[ 121.907578] tegra-mgbe 6910000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 121.908399] tegra-mgbe 6910000.ethernet eth1: registered PTP clock
[ 121.908582] tegra-mgbe 6910000.ethernet eth1: configuring for phy/10gbase-r link mode
[ 125.961292] tegra-mgbe 6910000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 181.921198] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 181.921404] rcu: 7-....: (1 GPs behind) idle=540c/1/0x4000000000000002 softirq=1748/1749 fqs=2337
[ 181.921684] rcu: (detected by 4, t=6002 jiffies, g=1357, q=1254 ncpus=8)
[ 181.921878] Sending NMI from CPU 4 to CPUs 7:
[ 181.921886] NMI backtrace for cpu 7
[ 181.922131] CPU: 7 UID: 0 PID: 0 Comm: swapper/7 Kdump: loaded Not tainted 6.13.0-rc3+ #6
[ 181.922390] Hardware name: NVIDIA CTI Forge + Orin AGX/Jetson, BIOS 202402.1-Unknown 10/28/2024
[ 181.922658] pstate: 40400009 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 181.922847] pc : handle_softirqs+0x98/0x368
[ 181.922978] lr : __do_softirq+0x18/0x20
[ 181.923095] sp : ffff80008003bf50
[ 181.923189] x29: ffff80008003bf50 x28: 0000000000000008 x27: 0000000000000000
[ 181.923379] x26: ffffce78ea277000 x25: 0000000000000000 x24: 0000001c61befda0
[ 181.924486] x23: 0000000060400009 x22: ffffce78e99918bc x21: ffff80008018bd70
[ 181.925568] x20: ffffce78e8bb00d8 x19: ffff80008018bc20 x18: 0000000000000000
[ 181.926655] x17: ffff318ebe7d3000 x16: ffff800080038000 x15: 0000000000000000
[ 181.931455] x14: ffff000080816680 x13: ffff318ebe7d3000 x12: 000000003464d91d
[ 181.938628] x11: 0000000000000040 x10: ffff000080165a70 x9 : ffffce78e8bb0160
[ 181.945804] x8 : ffff8000827b3160 x7 : f9157b241586f343 x6 : eeb6502a01c81c74
[ 181.953068] x5 : a4acfcdd2e8096bb x4 : ffffce78ea277340 x3 : 00000000ffffd1e1
[ 181.960329] x2 : 0000000000000101 x1 : ffffce78ea277340 x0 : ffff318ebe7d3000
[ 181.967591] Call trace:
[ 181.970043] handle_softirqs+0x98/0x368 (P)
[ 181.974240] __do_softirq+0x18/0x20
[ 181.977743] ____do_softirq+0x14/0x28
[ 181.981415] call_on_irq_stack+0x24/0x30
[ 181.985180] do_softirq_own_stack+0x20/0x30
[ 181.989379] __irq_exit_rcu+0x114/0x140
[ 181.993142] irq_exit_rcu+0x14/0x28
[ 181.996816] el1_interrupt+0x44/0xb8
[ 182.000316] el1h_64_irq_handler+0x14/0x20
[ 182.004343] el1h_64_irq+0x80/0x88
[ 182.007755] cpuidle_enter_state+0xc4/0x4a8 (P)
[ 182.012305] cpuidle_enter+0x3c/0x58
[ 182.015980] cpuidle_idle_call+0x128/0x1c0
[ 182.020005] do_idle+0xe0/0xf0
[ 182.023155] cpu_startup_entry+0x3c/0x48
[ 182.026917] secondary_start_kernel+0xdc/0x120
[ 182.031379] __secondary_switched+0x74/0x78
[ 212.971162] rcu: INFO: rcu_preempt detected expedited stalls on CPUs/tasks: { 7-.... } 6103 jiffies s: 417 root: 0x80/.
[ 212.985935] rcu: blocking rcu_node structures (internal RCU debug):
[ 212.992758] Sending NMI from CPU 0 to CPUs 7:
[ 212.998539] NMI backtrace for cpu 7
[ 213.004304] CPU: 7 UID: 0 PID: 0 Comm: swapper/7 Kdump: loaded Not tainted 6.13.0-rc3+ #6
[ 213.016116] Hardware name: NVIDIA CTI Forge + Orin AGX/Jetson, BIOS 202402.1-Unknown 10/28/2024
[ 213.030817] pstate: 40400009 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 213.040528] pc : handle_softirqs+0x98/0x368
[ 213.046563] lr : __do_softirq+0x18/0x20
[ 213.051293] sp : ffff80008003bf50
[ 213.055839] x29: ffff80008003bf50 x28: 0000000000000008 x27: 0000000000000000
[ 213.067304] x26: ffffce78ea277000 x25: 0000000000000000 x24: 0000001c61befda0
[ 213.077014] x23: 0000000060400009 x22: ffffce78e99918bc x21: ffff80008018bd70
[ 213.087339] x20: ffffce78e8bb00d8 x19: ffff80008018bc20 x18: 0000000000000000
[ 213.097313] x17: ffff318ebe7d3000 x16: ffff800080038000 x15: 0000000000000000
[ 213.107201] x14: ffff000080816680 x13: ffff318ebe7d3000 x12: 000000003464d91d
[ 213.116651] x11: 0000000000000040 x10: ffff000080165a70 x9 : ffffce78e8bb0160
[ 213.127500] x8 : ffff8000827b3160 x7 : 0a37b344852820af x6 : 3f049caedd1ff608
[ 213.138002] x5 : cff7cfdbfaf31291 x4 : ffffce78ea277340 x3 : 00000000ffffde04
[ 213.150428] x2 : 0000000000000101 x1 : ffffce78ea277340 x0 : ffff318ebe7d3000
[ 213.162063] Call trace:
[ 213.165494] handle_softirqs+0x98/0x368 (P)
[ 213.171256] __do_softirq+0x18/0x20
[ 213.177291] ____do_softirq+0x14/0x28
[ 213.182017] call_on_irq_stack+0x24/0x30
[ 213.186565] do_softirq_own_stack+0x20/0x30
[ 213.191815] __irq_exit_rcu+0x114/0x140
[ 213.196891] irq_exit_rcu+0x14/0x28
[ 213.202401] el1_interrupt+0x44/0xb8
[ 213.207741] el1h_64_irq_handler+0x14/0x20
[ 213.213519] el1h_64_irq+0x80/0x88
[ 213.217541] cpuidle_enter_state+0xc4/0x4a8 (P)
[ 213.224364] cpuidle_enter+0x3c/0x58
[ 213.228653] cpuidle_idle_call+0x128/0x1c0
[ 213.233993] do_idle+0xe0/0xf0
[ 213.237928] cpu_startup_entry+0x3c/0x48
[ 213.243791] secondary_start_kernel+0xdc/0x120
[ 213.249830] __secondary_switched+0x74/0x78
This bug has existed since the dwmac-tegra driver was added in Dec 2022
(See Fixes tag below for commit hash).
The Tegra234 SOC has 4 MGBE controllers, however Nvidia's Developer Kit
only uses MGBE0 which is why the bug was not found previously. Connect Tech
has many products that use 2 (or more) MGBE controllers.
The solution is to read the controller's SID from the existing "iommus"
device tree property. The 2nd field of the "iommus" device tree property
is the controller's SID.
Device tree snippet from tegra234.dtsi showing MGBE1's "iommus" property:
smmu_niso0: iommu@12000000 {
compatible = "nvidia,tegra234-smmu", "nvidia,smmu-500";
...
}
/* MGBE1 */
ethernet@6900000 {
compatible = "nvidia,tegra234-mgbe";
...
iommus = <&smmu_niso0 TEGRA234_SID_MGBE_VF1>;
...
}
Nvidia's arm-smmu driver reads the "iommus" property and stores the SID in
the MGBE device's "fwspec" struct. The dwmac-tegra driver can access the
SID using the tegra_dev_iommu_get_stream_id() helper function found in
linux/iommu.h.
Calling tegra_dev_iommu_get_stream_id() should not fail unless the "iommus"
property is removed from the device tree or the IOMMU is disabled.
While the Tegra234 SOC technically supports bypassing the IOMMU, it is not
supported by the current firmware, has not been tested and not recommended.
More detailed discussion with Thierry Reding from Nvidia linked below.
Fixes: d8ca113724e7 ("net: stmmac: tegra: Add MGBE support")
Link: https://lore.kernel.org/netdev/cover.1731685185.git.pnewman@connecttech.com
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patch.msgid.link/6fb97f32cf4accb4f7cf92846f6b60064ba0a3bd.1736284360.git.pnewman@connecttech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support triggering queue reset via debugfs for an upcoming test.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add queue management API support. We need a way to reset queues
to test NAPI reordering, the queue management API provides a
handy scaffolding for that.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We'll need the code to allocate and free queues in the queue management
API, factor it out.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Make nsim->rqs an array of pointers and allocate them individually
so that we can swap them out one by one.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Link the NAPI instances to their configs. This will be needed to test
that NAPI config doesn't break list ordering.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The overflow_work is using system wq to do overflow checks and updates
for PHC device timecounter, which might be overhelmed by other tasks.
But there is dedicated kthread in PTP subsystem designed for such
things. This patch changes the work queue to proper align with PTP
subsystem and to avoid overloading system work queue.
The adjfine() function acts the same way as overflow check worker,
we can postpone ptp aux worker till the next overflow period after
adjfine() was called.
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250107104812.380225-1-vadfed@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
stmmac_rx_offset() is referenced in stmmac_main.c only,
let's move it to stmmac_main.c.
Drop the inline keyword by the way, it is better to let the compiler
to decide.
Compile tested only.
No functional change intended.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250107075448.4039925-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for RTL8125BP rev.b. Its XID is 0x689. This chip supports
DASH and its dash type is "RTL_DASH_25_BP".
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20250107064355.104711-1-hau@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We found a timeout problem with the pldm command on our system. The
reason is that the MCTP-I3C driver has a race condition when receiving
multiple-packet messages in multi-thread, resulting in a wrong packet
order problem.
We identified this problem by adding a debug message to the
mctp_i3c_read function.
According to the MCTP spec, a multiple-packet message must be composed
in sequence, and if there is a wrong sequence, the whole message will be
discarded and wait for the next SOM.
For example, SOM → Pkt Seq #2 → Pkt Seq #1 → Pkt Seq #3 → EOM.
Therefore, we try to solve this problem by adding a mutex to the
mctp_i3c_read function. Before the modification, when a command
requesting a multiple-packet message response is sent consecutively, an
error usually occurs within 100 loops. After the mutex, it can go
through 40000 loops without any error, and it seems to run well.
Fixes: c8755b29b58e ("mctp i3c: MCTP I3C driver")
Signed-off-by: Leo Yang <Leo-Yang@quantatw.com>
Link: https://patch.msgid.link/20250107031529.3296094-1-Leo-Yang@quantatw.com
[pabeni@redhat.com: dropped already answered question from changelog]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-01-07 (ice, igc)
For ice:
Arkadiusz corrects mask value being used to determine DPLL phase range.
Przemyslaw corrects frequency value for E823 devices.
For igc:
En-Wei Wu adds a check and, early, return for failed register read.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: return early when failing to read EECD register
ice: fix incorrect PHY settings for 100 GB/s
ice: fix max values for dpll pin phase adjust
====================
Link: https://patch.msgid.link/20250107190150.1758577-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
