| Age | Commit message (Collapse) | Author |
|---|
|
again after probe failed
The expander phy will be treated as broadcast flutter in the next
revalidation after the exp-attached end device probe failed, as follows:
[78779.654026] sas: broadcast received: 0
[78779.654037] sas: REVALIDATING DOMAIN on port 0, pid:10
[78779.654680] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78779.662977] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78779.662986] sas: ex 500e004aaaaaaa1f phy05 new device attached
[78779.663079] sas: ex 500e004aaaaaaa1f phy05:U:8 attached: 500e004aaaaaaa05 (stp)
[78779.693542] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] found
[78779.701155] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[78779.707864] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
...
[78835.161307] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[78835.171344] sas: sas_probe_sata: for exp-attached device 500e004aaaaaaa05 returned -19
[78835.180879] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] is gone
[78835.187487] sas: broadcast received: 0
[78835.187504] sas: REVALIDATING DOMAIN on port 0, pid:10
[78835.188263] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78835.195870] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78835.195875] sas: ex 500e004aaaaaaa1f rediscovering phy05
[78835.196022] sas: ex 500e004aaaaaaa1f phy05:U:A attached: 500e004aaaaaaa05 (stp)
[78835.196026] sas: ex 500e004aaaaaaa1f phy05 broadcast flutter
[78835.197615] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
The cause of the problem is that the related ex_phy's attached_sas_addr was
not cleared after the end device probe failed, so reset it.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240619091742.25465-1-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
dma_pad_mask is a queue_limits by all ways of looking at it, so move it
there and set it through the atomic queue limits APIs.
Add a little helper that takes the alignment and pad into account to
simplify the code that is touched a bit.
Note that there never was any need for the > check in
blk_queue_update_dma_pad, this probably was just copy and paste from
dma_update_dma_alignment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240626142637.300624-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Target debugfs entry is removed via async_schedule() which isn't drained
when adding same name target, so failure of "Directory 'target11:0:0' with
parent 'scsi_debug' already present!" can be triggered easily.
Fix it by switching to domain async schedule, and draining it before
adding new target debugfs entry.
Cc: Wenchao Hao <haowenchao2@huawei.com>
Fixes: f084fe52c640 ("scsi: scsi_debug: Add debugfs interface to fail target reset")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Wenchao Hao <haowenchao22@gmail.com>
Link: https://lore.kernel.org/r/20240619013803.3008857-1-ming.lei@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Implement the 'host_traddr' callback to display the host transport
address for nvmet debugfs.
Signed-off-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fixes: one in the ufs driver fixing an obvious memory leak and the
other (with a core flag based update) trying to prevent USB crashes by
stopping the core from issuing a request for the I/O Hints mode page"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: usb: uas: Do not query the IO Advice Hints Grouping mode page for USB/UAS devices
scsi: core: Introduce the BLIST_SKIP_IO_HINTS flag
scsi: ufs: core: Free memory allocated for model before reinit
|
|
Add initial support for atomic writes.
As is standard method, feed device properties via modules param, those
being:
- atomic_max_size_blks
- atomic_alignment_blks
- atomic_granularity_blks
- atomic_max_size_with_boundary_blks
- atomic_max_boundary_blks
These just match sbc4r22 section 6.6.4 - Block limits VPD page.
We just support ATOMIC WRITE (16).
The major change in the driver is how we lock the device for RW accesses.
Currently the driver uses a per-device lock for accessing device metadata
and "media" data (calls to do_device_access()) atomically for the duration
of the whole read/write command.
This should not suit verifying atomic writes. Reason being that currently
all reads/writes are atomic, so using atomic writes does not prove
anything.
Change device access model to basis that regular writes only atomic on a
per-sector basis, while reads and atomic writes are fully atomic.
As mentioned, since accessing metadata and device media is atomic,
continue to have regular writes involving metadata - like discard or PI -
as atomic. We can improve this later.
Currently we only support model where overlapping going reads or writes
wait for current access to complete before commencing an atomic write.
This is described in 4.29.3.2 section of the SBC. However, we simplify,
things and wait for all accesses to complete (when issuing an atomic
write).
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20240620125359.2684798-10-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Support is divided into two main areas:
- reading VPD pages and setting sdev request_queue limits
- support WRITE ATOMIC (16) command and tracing
The relevant block limits VPD page need to be read to allow the block layer
request_queue atomic write limits to be set. These VPD page limits are
described in sbc4r22 section 6.6.4 - Block limits VPD page.
There are five limits of interest:
- MAXIMUM ATOMIC TRANSFER LENGTH
- ATOMIC ALIGNMENT
- ATOMIC TRANSFER LENGTH GRANULARITY
- MAXIMUM ATOMIC TRANSFER LENGTH WITH BOUNDARY
- MAXIMUM ATOMIC BOUNDARY SIZE
MAXIMUM ATOMIC TRANSFER LENGTH is the maximum length for a WRITE ATOMIC
(16) command. It will not be greater than the device MAXIMUM TRANSFER
LENGTH.
ATOMIC ALIGNMENT and ATOMIC TRANSFER LENGTH GRANULARITY are the minimum
alignment and length values for an atomic write in terms of logical blocks.
Unlike NVMe, SCSI does not specify an LBA space boundary, but does specify
a per-IO boundary granularity. The maximum boundary size is specified in
MAXIMUM ATOMIC BOUNDARY SIZE. When used, this boundary value is set in the
WRITE ATOMIC (16) ATOMIC BOUNDARY field - layout for the WRITE_ATOMIC_16
command can be found in sbc4r22 section 5.48. This boundary value is the
granularity size at which the device may atomically write the data. A value
of zero in WRITE ATOMIC (16) ATOMIC BOUNDARY field means that all data must
be atomically written together.
MAXIMUM ATOMIC TRANSFER LENGTH WITH BOUNDARY is the maximum atomic write
length if a non-zero boundary value is set.
For atomic write support, the WRITE ATOMIC (16) boundary is not of much
interest, as the block layer expects each request submitted to be executed
atomically. However, the SCSI spec does leave itself open to a quirky
scenario where MAXIMUM ATOMIC TRANSFER LENGTH is zero, yet MAXIMUM ATOMIC
TRANSFER LENGTH WITH BOUNDARY and MAXIMUM ATOMIC BOUNDARY SIZE are both
non-zero. This case will be supported.
To set the block layer request_queue atomic write capabilities, sanitize
the VPD page limits and set limits as follows:
- atomic_write_unit_min is derived from granularity and alignment values.
If no granularity value is not set, use physical block size
- atomic_write_unit_max is derived from MAXIMUM ATOMIC TRANSFER LENGTH. In
the scenario where MAXIMUM ATOMIC TRANSFER LENGTH is zero and boundary
limits are non-zero, use MAXIMUM ATOMIC BOUNDARY SIZE for
atomic_write_unit_max. New flag scsi_disk.use_atomic_write_boundary is
set for this scenario.
- atomic_write_boundary_bytes is set to zero always
SCSI also supports a WRITE ATOMIC (32) command, which is for type 2
protection enabled. This is not going to be supported now, so check for
T10_PI_TYPE2_PROTECTION when setting any request_queue limits.
To handle an atomic write request, add support for WRITE ATOMIC (16)
command in handler sd_setup_atomic_cmnd(). Flag use_atomic_write_boundary
is checked here for encoding ATOMIC BOUNDARY field.
Trace info is also added for WRITE_ATOMIC_16 command.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20240620125359.2684798-9-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the bounce flag into the features field to reclaim a little bit of
space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-27-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the zone_resetall flag into the queue_limits feature field so that
it can be set atomically with the queue frozen.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-24-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the zoned flags into the features field to reclaim a little
bit of space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-23-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the stable_writes flag into the queue_limits feature field so that
it can be set atomically with the queue frozen.
The flag is now inherited by blk_stack_limits, which greatly simplifies
the code in dm, and fixed md which previously did not pass on the flag
set on lower devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-18-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the add_random flag into the queue_limits feature field so that it
can be set atomically with the queue frozen.
Note that this also removes code from dm to clear the flag based on
the underlying devices, which can't be reached as dm devices will
always start out without the flag set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-16-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the nonrot flag into the queue_limits feature field so that it can
be set atomically with the queue frozen.
Use the chance to switch to defaulting to non-rotational and require
the driver to opt into rotational, which matches the polarity of the
sysfs interface.
For the z2ram, ps3vram, 2x memstick, ubiblock and dcssblk the new
rotational flag is not set as they clearly are not rotational despite
this being a behavior change. There are some other drivers that
unconditionally set the rotational flag to keep the existing behavior
as they arguably can be used on rotational devices even if that is
probably not their main use today (e.g. virtio_blk and drbd).
The flag is automatically inherited in blk_stack_limits matching the
existing behavior in dm and md.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the cache control settings into the queue_limits so that the flags
can be set atomically with the device queue frozen.
Add new features and flags field for the driver set flags, and internal
(usually sysfs-controlled) flags in the block layer. Note that we'll
eventually remove enough field from queue_limits to bring it back to the
previous size.
The disable flag is inverted compared to the previous meaning, which
means it now survives a rescan, similar to the max_sectors and
max_discard_sectors user limits.
The FLUSH and FUA flags are now inherited by blk_stack_limits, which
simplified the code in dm a lot, but also causes a slight behavior
change in that dm-switch and dm-unstripe now advertise a write cache
despite setting num_flush_bios to 0. The I/O path will handle this
gracefully, but as far as I can tell the lack of num_flush_bios
and thus flush support is a pre-existing data integrity bug in those
targets that really needs fixing, after which a non-zero num_flush_bios
should be required in dm for targets that map to underlying devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-14-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move a bit of code that sets up the zone flag and the write granularity
into sd_zbc_read_zones to be with the rest of the zoned limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since commit 7437bb73f087 ("block: remove support for the host aware zone
model"), only ZBC devices expose a zoned access model. sd_is_zoned is
used to check for that and thus return false for host aware devices.
Replace the helper with the simple open coded TYPE_ZBC check to fix this.
Fixes: 7437bb73f087 ("block: remove support for the host aware zone model")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240617060532.127975-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three obvious driver fixes and two core fixes.
The two core fixes are to disable Command Duration Limits by default
to fix an inconsistency in SATA and some USB devices. The other is to
change the default read size for block zero to follow the device
preference (some USB bridges preferring 16 byte commands don't have a
translation for READ(10) and thus don't scan properly)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpi3mr: Fix ATA NCQ priority support
scsi: ufs: core: Quiesce request queues before checking pending cmds
scsi: core: Disable CDL by default
scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory
scsi: sd: Use READ(16) when reading block zero on large capacity disks
|
|
Move the integrity information into the queue limits so that it can be
set atomically with other queue limits, and that the sysfs changes to
the read_verify and write_generate flags are properly synchronized.
This also allows to provide a more useful helper to stack the integrity
fields, although it still is separate from the main stacking function
as not all stackable devices want to inherit the integrity settings.
Even with that it greatly simplifies the code in md and dm.
Note that the integrity field is moved as-is into the queue limits.
While there are good arguments for removing the separate blk_integrity
structure, this would cause a lot of churn and might better be done at a
later time if desired. However the integrity field in the queue_limits
structure is now unconditional so that various ifdefs can be avoided or
replaced with IS_ENABLED(). Given that tiny size of it that seems like
a worthwhile trade off.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240613084839.1044015-13-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Block layer integrity configuration is a bit complex right now, as it
indirects through operation vectors for a simple two-dimensional
configuration:
a) the checksum type of none, ip checksum, crc, crc64
b) the presence or absence of a reference tag
Remove the integrity profile, and instead add a separate csum_type flag
which replaces the existing ip-checksum field and a new flag that
indicates the presence of the reference tag.
This removes up to two layers of indirect calls, remove the need to
offload the no-op verification of non-PI metadata to a workqueue and
generally simplifies the code. The downside is that block/t10-pi.c now
has to be built into the kernel when CONFIG_BLK_DEV_INTEGRITY is
supported. Given that both nvme and SCSI require t10-pi.ko, it is loaded
for all usual configurations that enabled CONFIG_BLK_DEV_INTEGRITY
already, though.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240613084839.1044015-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A few drivers optimistically try to support discard, write zeroes and
secure erase and disable the features from the I/O completion handler
if the hardware can't support them. This disable can't be done using
the atomic queue limits API because the I/O completion handlers can't
take sleeping locks or freeze the queue. Keep the existing clearing
of the relevant field to zero, but replace the old blk_queue_max_*
APIs with new disable APIs that force the value to 0.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Assign all queue limits through a local queue_limits variable and
queue_limits_commit_update so that we can't race updating them from
multiple places, and free the queue when updating them so that
in-progress I/O submissions don't see half-updated limits.
Also use the chance to clean up variable names to standard ones.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-13-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Assign all queue limits through a local queue_limits variable and
queue_limits_commit_update so that we can't race updating them from
multiple places, and freeze the queue when updating them so that
in-progress I/O submissions don't see half-updated limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Consolidate setting zone-related queue limits in sd_zbc_read_zones
instead of splitting them between sd_zbc_revalidate_zones and
sd_zbc_read_zones, and move the early_zone_information initialization
in sd_zbc_read_zones above setting up the queue limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-11-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Split the logic to pick the right discard mode into a little helper
to prepare for further changes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fall through to the main call to blk_queue_max_discard_sectors given that
max_blocks has been initialized to zero above instead of duplicating the
call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add helper to disable WRITE SAME when it is not supported and use it
instead of sd_config_write_same in the I/O completion handler. This
avoids touching more fields than required in the I/O completion handler
and prepares for converting sd to use the atomic queue limits API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add helper to disable discard when it is not supported and use it
instead of sd_config_discard in the I/O completion handler. This avoids
touching more fields than required in the I/O completion handler and
prepares for converting sd to use the atomic queue limits API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Don't reset the discard settings to no-op over and over when a user
writes to the provisioning attribute as that is already the default
mode for ZBC devices. In hindsight we should have made writing to
the attribute fail for ZBC devices, but the code has probably been
around for far too long to change this now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The soft max_sectors limit is normally capped by the hardware limits and
an arbitrary upper limit enforced by the kernel, but can be modified by
the user. A few drivers want to increase this limit (nbd, rbd) or
adjust it up or down based on hardware capabilities (sd).
Change blk_validate_limits to default max_sectors to the optimal I/O
size, or upgrade it to the preferred minimal I/O size if that is
larger than the kernel default if no optimal I/O size is provided based
on the logic in the SD driver.
This keeps the existing kernel default for drivers that do not provide
an io_opt or very big io_min value, but picks a much more useful
default for those who provide these hints, and allows to remove the
hacks to set the user max_sectors limit in nbd, rbd and sd.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Prepare for skipping the IO Advice Hints Grouping mode page for USB storage
devices.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Joao Machado <jocrismachado@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Christian Heusel <christian@heusel.eu>
Cc: stable@vger.kernel.org
Fixes: 4f53138fffc2 ("scsi: sd: Translate data lifetime information")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240613211828.2077477-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The comment that scsi_static_device_list would go away was added more than
18 years ago. Today, that list is still there and a large number of
additional entries have been added. This shows that this comment is
incorrect. Hence fix that comment.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240612171522.2677600-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The function mpi3mr_qcmd() of the mpi3mr driver is able to indicate to
the HBA if a read or write command directed at an ATA device should be
translated to an NCQ read/write command with the high prioiryt bit set
when the request uses the RT priority class and the user has enabled NCQ
priority through sysfs.
However, unlike the mpt3sas driver, the mpi3mr driver does not define
the sas_ncq_prio_supported and sas_ncq_prio_enable sysfs attributes, so
the ncq_prio_enable field of struct mpi3mr_sdev_priv_data is never
actually set and NCQ Priority cannot ever be used.
Fix this by defining these missing atributes to allow a user to check if
an ATA device supports NCQ priority and to enable/disable the use of NCQ
priority. To do this, lift the function scsih_ncq_prio_supp() out of the
mpt3sas driver and make it the generic SCSI SAS transport function
sas_ata_ncq_prio_supported(). Nothing in that function is hardware
specific, so this function can be used in both the mpt3sas driver and
the mpi3mr driver.
Reported-by: Scott McCoy <scott.mccoy@wdc.com>
Fixes: 023ab2a9b4ed ("scsi: mpi3mr: Add support for queue command processing")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240611083435.92961-1-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/scsi_common.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/advansys.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/BusLogic.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/aha1740.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/isci/isci.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/elx/efct.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/atp870u.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/ppa.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/imm.o
Add all missing invocations of the MODULE_DESCRIPTION() macro.
This updates all files which have a MODULE_LICENSE() but which do not have
a MODULE_DESCRIPTION(), even ones which did not produce the x86
allmodconfig warnings.
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240610-md-drivers-scsi-v3-1-055da78d66b2@quicinc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For SCSI devices supporting the Command Duration Limits feature set, the
user can enable/disable this feature use through the sysfs device attribute
"cdl_enable". This attribute modification triggers a call to
scsi_cdl_enable() to enable and disable the feature for ATA devices and set
the scsi device cdl_enable field to the user provided bool value. For SCSI
devices supporting CDL, the feature set is always enabled and
scsi_cdl_enable() is reduced to setting the cdl_enable field.
However, for ATA devices, a drive may spin-up with the CDL feature enabled
by default. But the SCSI device cdl_enable field is always initialized to
false (CDL disabled), regardless of the actual device CDL feature
state. For ATA devices managed by libata (or libsas), libata-core always
disables the CDL feature set when the device is attached, thus syncing the
state of the CDL feature on the device and of the SCSI device cdl_enable
field. However, for ATA devices connected to a SAS HBA, the CDL feature is
not disabled on scan for ATA devices that have this feature enabled by
default, leading to an inconsistent state of the feature on the device with
the SCSI device cdl_enable field.
Avoid this inconsistency by adding a call to scsi_cdl_enable() in
scsi_cdl_check() to make sure that the device-side state of the CDL feature
set always matches the scsi device cdl_enable field state. This implies
that CDL will always be disabled for ATA devices connected to SAS HBAs,
which is consistent with libata/libsas initialization of the device.
Reported-by: Scott McCoy <scott.mccoy@wdc.com>
Fixes: 1b22cfb14142 ("scsi: core: Allow enabling and disabling command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240607012507.111488-1-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The core change is to detect unusually large number of VPD pages
(caused by device manufacturers having an endiannes issue) and reject
them rather than trying to parse a huge non-existent array.
The remaining fixes are in drivers the most user visible of which is
the ALUA state transition recognition (leads to intermittent I/O
errors in some situations otherwise)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: mcq: Fix error output and clean up ufshcd_mcq_abort()
scsi: core: Handle devices which return an unusually large VPD page count
scsi: mpt3sas: Add missing kerneldoc parameter descriptions
scsi: qedf: Set qed_slowpath_params to zero before use
scsi: qedf: Wait for stag work during unload
scsi: qedf: Don't process stag work during unload and recovery
scsi: sr: Fix unintentional arithmetic wraparound
scsi: core: alua: I/O errors for ALUA state transitions
scsi: mpi3mr: Use proper format specifier in mpi3mr_sas_port_add()
|
|
There is a potential out-of-bounds access when using test_bit() on a single
word. The test_bit() and set_bit() functions operate on long values, and
when testing or setting a single word, they can exceed the word
boundary. KASAN detects this issue and produces a dump:
BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas
Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965
For full log, please look at [1].
Make the allocation at least the size of sizeof(unsigned long) so that
set_bit() and test_bit() have sufficient room for read/write operations
without overwriting unallocated memory.
[1] Link: https://lore.kernel.org/all/ZkNcALr3W3KGYYJG@gmail.com/
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Cc: stable@vger.kernel.org
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240605085530.499432-1-leitao@debian.org
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 321da3dc1f3c ("scsi: sd: usb_storage: uas: Access media prior
to querying device properties") triggered a read to LBA 0 before
attempting to inquire about device characteristics. This was done
because some protocol bridge devices will return generic values until
an attached storage device's media has been accessed.
Pierre Tomon reported that this change caused problems on a large
capacity external drive connected via a bridge device. The bridge in
question does not appear to implement the READ(10) command.
Issue a READ(16) instead of READ(10) when a device has been identified
as preferring 16-byte commands (use_16_for_rw heuristic).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218890
Link: https://lore.kernel.org/r/70dd7ae0-b6b1-48e1-bb59-53b7c7f18274@rowland.harvard.edu
Link: https://lore.kernel.org/r/20240605022521.3960956-1-martin.petersen@oracle.com
Fixes: 321da3dc1f3c ("scsi: sd: usb_storage: uas: Access media prior to querying device properties")
Cc: stable@vger.kernel.org
Reported-by: Pierre Tomon <pierretom+12@ik.me>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pierre Tomon <pierretom+12@ik.me>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Bart Van Assche <bvanassche@acm.org> says:
Hi Martin,
There are several 32-bit ARM SCSI drivers that trigger compiler warnings
about missing function declarations. This patch series fixes these
compiler warnings by declaring local functions static. Please consider
this patch series for the next merge window.
Thanks,
Bart.
Link: https://lore.kernel.org/r/20240603172311.1587589-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240603172311.1587589-5-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240603172311.1587589-4-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240603172311.1587589-3-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240603172311.1587589-2-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- scsi: mpt3sas: Avoid possible run-time warning with long manufacturer
strings
- mailmap: update entry for Kees Cook
- kunit/fortify: Remove __kmalloc_node() test
* tag 'hardening-v6.10-rc2-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
kunit/fortify: Remove __kmalloc_node() test
mailmap: update entry for Kees Cook
scsi: mpt3sas: Avoid possible run-time warning with long manufacturer strings
|
|
The prior strscpy() replacement of strncpy() here expected the
manufacture_reply strings to be NUL-terminated, but it is possible
they are not, as the code pattern here shows, e.g., edev->vendor_id
being exactly 1 character larger than manufacture_reply->vendor_id,
and the replaced strncpy() was copying only up to the size of the
source character array. Replace this with memtostr(), which is the
unambiguous way to convert a maybe not-NUL-terminated character array
into a NUL-terminated string.
Fixes: b7e9712a02e8 ("scsi: mpt3sas: Replace deprecated strncpy() with strscpy()")
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Marco Patalano <mpatalan@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240410023155.2100422-3-keescook@chromium.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
'scsi_dif_tuple' is unused since commit 8cb2049c7448 ("[SCSI] qla2xxx: T10
DIF - Handle uninitalized sectors.").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240528215640.91771-1-linux@treblig.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When calling scsi_alloc_sdev() -> blk_mq_alloc_queue(), we don't pass
the sdev as the queuedata, but rather manually set it afterwards. Just
pass to blk_mq_alloc_queue() to have automatically set.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240524084829.2132555-2-john.g.garry@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull in remaining commits from 6.10/scsi-queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
sd can set a max_sectors value that is lower than the max_hw_sectors
limit based on the block limits VPD page. While this is rather unusual,
it used to work until the max_user_sectors field was split out to cleanly
deal with conflicting hardware and user limits when the hardware limit
changes. Also set max_user_sectors to ensure the limit can properly be
stacked.
Fixes: 4f563a64732d ("block: add a max_user_discard_sectors queue limit")
Reported-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240523182618.602003-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Peter Schneider reported that a system would no longer boot after
updating to 6.8.4. Peter bisected the issue and identified commit
b5fc07a5fb56 ("scsi: core: Consult supported VPD page list prior to
fetching page") as being the culprit.
Turns out the enclosure device in Peter's system reports a byteswapped
page length for VPD page 0. It reports "02 00" as page length instead
of "00 02". This causes us to attempt to access 516 bytes (page length
+ header) of information despite only 2 pages being present.
Limit the page search scope to the size of our VPD buffer to guard
against devices returning a larger page count than requested.
Link: https://lore.kernel.org/r/20240521023040.2703884-1-martin.petersen@oracle.com
Fixes: b5fc07a5fb56 ("scsi: core: Consult supported VPD page list prior to fetching page")
Cc: stable@vger.kernel.org
Reported-by: Peter Schneider <pschneider1968@googlemail.com>
Closes: https://lore.kernel.org/all/eec6ebbf-061b-4a7b-96dc-ea748aa4d035@googlemail.com/
Tested-by: Peter Schneider <pschneider1968@googlemail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
|
