| Age | Commit message (Collapse) | Author |
|---|
|
Fixed some confusing typos that were currently identified with codespell,
the details are as follows:
-in the code comments:
drivers/usb/dwc3/core.c:1406: feild ==> field
drivers/usb/dwc3/core.h:84: boundries ==> boundaries
drivers/usb/dwc3/ep0.c:148: issueing ==> issuing
drivers/usb/dwc3/host.c:38: temperary ==> temporarily
Also fixed a syntax problem in the comments.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Link: https://lore.kernel.org/r/20240930022526.7255-1-shenlichuan@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's the limitation of Synopsys dwc3 controller with ERST programming in
supporting separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. But, writing operations
in xHCI is done low-high order following xHCI spec. xHCI specification 5.1
"Register Conventions" states that 64 bit registers should be written in
low-high order. Synopsys dwc3 needs workaround for high-low order. That's why
adding new quirk is needed to support this.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-2-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe82 ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the device is configured for system wakeup, then make sure that the
xHCI driver knows about it and make sure to permit wakeup only at the
appropriate time.
For host mode, if the controller goes through the dwc3 code path, then a
child xHCI platform device is created. Make sure the platform device
also inherits the wakeup setting for xHCI to enable remote wakeup.
For device mode, make sure to disable system wakeup if no gadget driver
is bound. We may experience unwanted system wakeup due to the wakeup
signal from the controller PMU detecting connection/disconnection when
in low power (D3). E.g. In the case of Steam Deck, the PCI PME prevents
the system staying in suspend.
Cc: stable@vger.kernel.org
Reported-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Closes: https://lore.kernel.org/linux-usb/70a7692d-647c-9be7-00a6-06fc60f77294@igalia.com/T/#mf00d6669c2eff7b308d1162acd1d66c09f0853c7
Fixes: d07e8819a03d ("usb: dwc3: add xHCI Host support")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Sanath S <Sanath.S@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://lore.kernel.org/r/667cfda7009b502e08462c8fb3f65841d103cc0a.1709865476.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove 'snps,host-vbus-glitches-quirk' and apply workaround
unconditionally.
It is safer to keep vbus disabled before handing over to xhci driver. So
needn't 'snps,host-vbus-glitches' property to enable it and apply it
unconditionally.
Remove all host_vbus_glitches variable and call
dwc3_power_off_all_roothub_ports() directly.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240212-vbus-glitch-v2-2-d71b73a82de1@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ioremap() function doesn't return error pointers, it returns NULL on
error. Update the check.
Fixes: 2d2a3349521d ("usb: dwc3: Add workaround for host mode VBUS glitch when boot")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/71499112-4ed3-489a-9a56-b4a8ab89cd05@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When DWC3 is set to host mode by programming register DWC3_GCTL, VBUS
(or its control signal) will be turned on immediately on related Root Hub
ports. Then, the VBUS is turned off for a little while(15us) when do xhci
reset (conducted by xhci driver) and back to normal finally, we can
observe a negative glitch of related signal happen.
This VBUS glitch might cause some USB devices enumeration fail if kernel
boot with them connected. Such as LS1012AFWRY/LS1043ARDB/LX2160AQDS
/LS1088ARDB with Kingston 16GB USB2.0/Kingston USB3.0/JetFlash Transcend
4GB USB2.0 drives. The fail cases include enumerated as full-speed device
or report wrong device descriptor, etc.
One SW workaround which can fix this is by programing all xhci PORTSC[PP]
to 0 to turn off VBUS immediately after setting host mode in DWC3 driver
(per signal measurement result, it will be too late to do it in
xhci-plat.c or xhci.c). Then, after xhci reset complete in xhci driver,
PORTSC[PP]s' value will back to 1 automatically and VBUS on at that time,
no glitch happen and normal enumeration process has no impact.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Upstream commit bac1ec551434 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. But the support for this quirk isn't present
in the DWC3 layer.
We will encounter this XHCI timeout/hung issue if we run iperf
loopback tests using RTL8156 ethernet adaptor on DWC3 targets
with scatter-gather enabled. This gets resolved after enabling
the XHCI_SG_TRB_CACHE_SIZE_QUIRK. This patch enables it using
the xhci device property since its needed for DWC3 controller.
In Synopsys DWC3 databook,
Table 9-3: xHCI Debug Capability Limitations
Chained TRBs greater than TRB cache size: The debug capability
driver must not create a multi-TRB TD that describes smaller
than a 1K packet that spreads across 8 or more TRBs on either
the IN TR or the OUT TR.
Cc: stable@vger.kernel.org #5.11
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-2-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the description of platform_get_irq()
* Return: non-zero IRQ number on success,
negative error number on failure.
and the code, platform_get_irq() will return -EINVAL
instead of IRQ0.
So platform_get_irq() no longer returns 0, there is no
need to check whether the return value is 0.
Found by Smatch:
drivers/usb/dwc3/host.c:60 dwc3_host_get_irq()
warn: platform_get_irq() does not return zero
Signed-off-by: Mingxuan Xiang <mx_xiang@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230324060934.1686859-1-mx_xiang@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 6000b8d900cd5f52fbcd0776d0cc396e88c8c2ea.
The offending commit disabled the USB core PHY management as the dwc3
already manages the PHYs in question.
Unfortunately some platforms have started relying on having USB core
also controlling the PHY and this is specifically currently needed on
some Exynos platforms for PHY calibration or connected device may fail
to enumerate.
The PHY calibration was previously handled in the dwc3 driver, but to
work around some issues related to how the dwc3 driver interacts with
xhci (e.g. using multiple drivers) this was moved to USB core by commits
34c7ed72f4f0 ("usb: core: phy: add support for PHY calibration") and
a0a465569b45 ("usb: dwc3: remove generic PHY calibrate() calls").
The same PHY obviously should not be controlled from two different
places, which for example do no agree on the PHY mode or power state
during suspend, but as the offending patch was backported to stable,
let's revert it for now.
Reported-by: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/lkml/808bdba846bb60456adf10a3016911ee@agner.ch/
Fixes: 6000b8d900cd ("usb: dwc3: disable USB core PHY management")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221103144648.14197-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dwc3 driver manages its PHYs itself so the USB core PHY management
needs to be disabled.
Use the struct xhci_plat_priv hack added by commits 46034a999c07 ("usb:
host: xhci-plat: add platform data support") and f768e718911e ("usb:
host: xhci-plat: add priv quirk for skip PHY initialization") to
propagate the setting for now.
Fixes: 4e88d4c08301 ("usb: add a flag to skip PHY initialization to struct usb_hcd")
Fixes: 178a0bce05cb ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Cc: stable <stable@kernel.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220825131836.19769-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Qualcomm dwc3 runtime-PM implementation checks the xhci
platform-device pointer in the wakeup-interrupt handler to determine
whether the controller is in host mode and if so triggers a resume.
After a role switch in OTG mode the xhci platform-device would have been
freed and the next wakeup from runtime suspend would access the freed
memory.
Note that role switching is executed from a freezable workqueue, which
guarantees that the pointer is stable during suspend.
Also note that runtime PM has been broken since commit 2664deb09306
("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which
incidentally also prevents this issue from being triggered.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is no longer needed. The sysdev pointer is now used when
assigning the ACPI companions to the xHCI ports and USB
devices.
Assigning the ACPI companion here resulted in the
fwnode->secondary pointer to be replaced also for the parent
dwc3 device since the primary fwnode (the ACPI companion)
was shared. That was unintentional and it created potential
side effects like resource leaks.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220428111056.3558-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop unneeded calls to platform_get_resource_byname() from
dwc3_host_init(). dwc3_host_init() already calls dwc3_host_get_irq()
which gets the irq number, just use this to get the IRQ resource data
and fill the xhci_resources[1]
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This replaces the platform_device_add_properties() call with
the safer device_create_managed_software_node() that does
exactly the same, but can also guarantee that the lifetime
of the node that is created for the device is tied to the
lifetime of device itself.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210204141711.53775-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200711135804.19735-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Synopsys introduces a new controller DWC_usb32. It supports dual-lane
and speed up to 20 Gbps, and the DWC3 driver will drive this controller.
Currently the driver uses a single field dwc->revision to ID both
DWC_usb3 and DWC_usb31 and their version number. This was sufficient for
two IPs, but this method doesn't work with additional IPs. As a result,
let's separate the dwc->revision field to 2 separate fields: ip and
revision. The ip field now stores the ID of the controller's IP while
the revision field stores the controller's version number.
This new scheme enforces DWC3 to compare the revision within the same IP
only. As a result, we must update all the revision check of the
controller to check its corresponding IP.
To help with this enforcement, we create a few macros to help with
the common version checks:
DWC3_IP_IS(IP)
DWC3_VER_IS(IP, VERSION)
DWC3_VER_IS_PRIOR(IP, VERSION)
DWC3_VER_IS_WITHIN(IP, LOWER_VERSION, UPPER_VERSION)
DWC3_VER_TYPE_IS_WITHIN(IP, VERSION,
LOWER_VERSION_TYPE,
UPPER_VERSION_TYPE)
The DWC_usb32 controller operates using the same programming model and
with very similar configurations as its previous controllers. Please
note that the various IP and revision checks in this patch match the
current checks for DWC_usb31 version 1.90a. Additional configurations
that are unique to DWC_usb32 are applied separately.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
The main comment in the file mistakenly marked with kernel doc annotation
which makes the parser unhappy:
.../dwc3/host.c:16: warning: Function parameter or member 'dwc' not described in 'dwc3_host_get_irq'
Drop kernel doc annotation from host.c module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
The ACPI companion of the adapter has to be set for xHCI controller
code to read and attach the ports described in the ACPI table.
Use ACPI_COMPANION_SET macro to set this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
We should not be reaching into property entries and initialize them by
hand, but rather use proper initializer macros. This way we can alter
internal representation of property entries with no visible changes to
their users.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since commit 7723f4c5ecdb ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() itself on
failure, so there is no need for the driver to also do this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dwc3 code to get the "peripheral" / "host" / "otg" IRQ first tries
platform_get_irq_byname() and then falls back to the IRQ at index 0 if
the platform_get_irq_byname().
In this case we do not want platform_get_irq_byname() to print an error
on failure, so switch to platform_get_irq_byname_optional() instead which
does not print an error.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205037
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 08f871a3aca2 ("usb: dwc3: host: convey the PHYs to xhci") added
forwarding of the generic PHYs from DWC3 core to the instantiated XHCI-plat
device. However XHCI(-plat) driver never gained support for generic PHYs,
thus the lookup added by that commit is never used. In meantime the commit
d64ff406e51e ("usb: dwc3: use bus->sysdev for DMA configuration")
incorrectly changed the device used for creating lookup, making the lookup
useless and generic PHYs inaccessible from XHCI device.
However since commit 178a0bce05cb ("usb: core: hcd: integrate the PHY
wrapper into the HCD core") USB HCD already handles generic PHYs acquired
from the HCD's 'sysdev', which in this case is DWC3 core device. This means
that creating any custom lookup entries for XHCI driver is no longer needed
and can be simply removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Support the option to disable USB2 LPM. Set xhci "usb2-lpm-disable"
property via "snps,usb2-lpm-disable" property.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dwc3 revisions <=3.00a have a limitation where Port Disable command
doesn't work. Set the quirk-broken-port-ped property for such
controllers so XHCI core can do the necessary workaround.
[rogerq@ti.com] Updated code from platform data to device property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The dma ops for dwc3 devices are not set properly. So, use a
physical device sysdev, which will be inherited from parent,
to set the hardware / firmware parameters like dma.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Cleanup only, no functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Looks like we lost all changes related to
commit 9522def40065 ("usb: dwc3: core: cleanup IRQ resources") in host.c
when Felipe's next branch was merged into Greg's next branch.
Fixes 215db948181 ("Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This should allow xhci to remove handling of platform data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch removes "Enable USB3 LPM Capability" option from Kconfig
and adds snps,usb3_lpm_capable devicetree property instead of it.
USB3 LPM (Link Power Management) capability is hardware property, and
it's platform dependent, so if our hardware supports this feature, we
want rather to configure it in devicetree than having it as Kconfig option.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On some platforms a PHY may need to be handled also in the
host controller driver. Exynos5420 SoC requires some "PHY
tuning" based on the USB speed. This patch delivers dwc3's
PHYs to the xhci platform device when it's created.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
All dwc3 based xhci host controller supports USB3.0 LPM functionality.
Therefore enable it in platform data for all dwc3 based xhci device if
DWC3_HOST_USB3_LPM_ENABLE is selected in Kconfig.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.
Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Multiple dwc3 controllers will try to allocate multiple xhci-hcd
interfaces.
Changing platform device IDs from NONE to AUTO to support
such cases.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This fix prevents a problem with dwc3 and host mode where
we were requesting the entire memory region in dwc3/core.c,
thus preventing xhci-plat from ever ioremapping its own address space.
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
PCI uses xhci-hcd, so let's use the same device
name to avoid confusion.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
None of these are required atm.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The Designware USB3 IP can be configured with
an internal xHCI. If we're running on such a
version, let's start the xHCI stack.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
