| Age | Commit message (Collapse) | Author |
|---|
|
property and typec_operation
The TI HD3SS3220 Type-C controller supports configuring
its role preference when operating as a dual-role port
through the SOURCE_PREF field of the General Control Register.
The previous driver behavior was to set the role preference
based on the dr_set typec_operation.
However, the controller does not support swapping the data role
on an active connection due to its lack of Power Delivery support.
Remove previous dr_set typec_operation, and support setting
the role preference based on the corresponding fwnode property,
as well as the try_role typec_operation.
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-3-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The TI HD3SS3220 Type-C controller supports configuring the port type
it will operate as through the MODE_SELECT field of the General
Control Register.
Configure the port type based on the fwnode property "power-role"
during probe, if present. If the property is absent, leave the
operation mode at the default, which is defined by the PORT pin
of the chip.
Support configuring the port type through the port_type_set
typec_operation as well.
The MODE_SELECT field can only be changed when the controller is in
unattached state, so follow the sequence recommended by the datasheet to:
1. disable termination on CC pins to disable the controller
2. change the mode
3. re-enable termination
This will effectively cause a connected device to disconnect
for the duration of the mode change.
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-2-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
property
The TI HD3SS3220 Type-C controller supports configuring its advertised
power operation mode over I2C using the CURRENT_MODE_ADVERTISE field
of the Connection Status Register.
Configure this power mode based on the existing (optional) property
"typec-power-opmode" of /schemas/connector/usb-connector.yaml
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-1-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit addresses an issue related to below kernel panic where
panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON
in functionsfs_bind, which easily leads to the following scenarios.
1.adb_write in adbd 2. UDC write via configfs
================= =====================
->usb_ffs_open_thread() ->UDC write
->open_functionfs() ->configfs_write_iter()
->adb_open() ->gadget_dev_desc_UDC_store()
->adb_write() ->usb_gadget_register_driver_owner
->driver_register()
->StartMonitor() ->bus_add_driver()
->adb_read() ->gadget_bind_driver()
<times-out without BIND event> ->configfs_composite_bind()
->usb_add_function()
->open_functionfs() ->ffs_func_bind()
->adb_open() ->functionfs_bind()
<ffs->state !=FFS_ACTIVE>
The adb_open, adb_read, and adb_write operations are invoked from the
daemon, but trying to bind the function is a process that is invoked by
UDC write through configfs, which opens up the possibility of a race
condition between the two paths. In this race scenario, the kernel panic
occurs due to the WARN_ON from functionfs_bind when panic_on_warn is
enabled. This commit fixes the kernel panic by removing the unnecessary
WARN_ON.
Kernel panic - not syncing: kernel: panic_on_warn set ...
[ 14.542395] Call trace:
[ 14.542464] ffs_func_bind+0x1c8/0x14a8
[ 14.542468] usb_add_function+0xcc/0x1f0
[ 14.542473] configfs_composite_bind+0x468/0x588
[ 14.542478] gadget_bind_driver+0x108/0x27c
[ 14.542483] really_probe+0x190/0x374
[ 14.542488] __driver_probe_device+0xa0/0x12c
[ 14.542492] driver_probe_device+0x3c/0x220
[ 14.542498] __driver_attach+0x11c/0x1fc
[ 14.542502] bus_for_each_dev+0x104/0x160
[ 14.542506] driver_attach+0x24/0x34
[ 14.542510] bus_add_driver+0x154/0x270
[ 14.542514] driver_register+0x68/0x104
[ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4
[ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144
[ 14.542526] configfs_write_iter+0xf0/0x138
Fixes: ddf8abd25994 ("USB: f_fs: the FunctionFS driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Akash M <akash.m5@samsung.com>
Link: https://lore.kernel.org/r/20241219125221.1679-1-akash.m5@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's USB error when tegra board is shutting down:
[ 180.919315] usb 2-3: Failed to set U1 timeout to 0x0,error code -113
[ 180.919995] usb 2-3: Failed to set U1 timeout to 0xa,error code -113
[ 180.920512] usb 2-3: Failed to set U2 timeout to 0x4,error code -113
[ 186.157172] tegra-xusb 3610000.usb: xHCI host controller not responding, assume dead
[ 186.157858] tegra-xusb 3610000.usb: HC died; cleaning up
[ 186.317280] tegra-xusb 3610000.usb: Timeout while waiting for evaluate context command
The issue is caused by disabling LPM on already suspended ports.
For USB2 LPM, the LPM is already disabled during port suspend. For USB3
LPM, port won't transit to U1/U2 when it's already suspended in U3,
hence disabling LPM is only needed for ports that are not suspended.
Cc: Wayne Chang <waynec@nvidia.com>
Cc: stable <stable@kernel.org>
Fixes: d920a2ed8620 ("usb: Disable USB3 LPM at shutdown")
Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20241206074817.89189-1-kaihengf@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When device_add(&udev->dev) succeeds and a later call fails,
usb_new_device() does not properly call device_del(). As comment of
device_add() says, 'if device_add() succeeds, you should call
device_del() when you want to get rid of it. If device_add() has not
succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable <stable@kernel.org>
Fixes: 9f8b17e643fe ("USB: make usbdevices export their device nodes instead of using a separate class")
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241218071346.2973980-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tcpci_irq() may meet below NULL pointer dereference issue:
[ 2.641851] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
[ 2.641951] status 0x1, 0x37f
[ 2.650659] Mem abort info:
[ 2.656490] ESR = 0x0000000096000004
[ 2.660230] EC = 0x25: DABT (current EL), IL = 32 bits
[ 2.665532] SET = 0, FnV = 0
[ 2.668579] EA = 0, S1PTW = 0
[ 2.671715] FSC = 0x04: level 0 translation fault
[ 2.676584] Data abort info:
[ 2.679459] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
[ 2.684936] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 2.689980] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 2.695284] [0000000000000010] user address but active_mm is swapper
[ 2.701632] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 2.707883] Modules linked in:
[ 2.710936] CPU: 1 UID: 0 PID: 87 Comm: irq/111-2-0051 Not tainted 6.12.0-rc6-06316-g7f63786ad3d1-dirty #4
[ 2.720570] Hardware name: NXP i.MX93 11X11 EVK board (DT)
[ 2.726040] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 2.732989] pc : tcpci_irq+0x38/0x318
[ 2.736647] lr : _tcpci_irq+0x14/0x20
[ 2.740295] sp : ffff80008324bd30
[ 2.743597] x29: ffff80008324bd70 x28: ffff800080107894 x27: ffff800082198f70
[ 2.750721] x26: ffff0000050e6680 x25: ffff000004d172ac x24: ffff0000050f0000
[ 2.757845] x23: ffff000004d17200 x22: 0000000000000001 x21: ffff0000050f0000
[ 2.764969] x20: ffff000004d17200 x19: 0000000000000000 x18: 0000000000000001
[ 2.772093] x17: 0000000000000000 x16: ffff80008183d8a0 x15: ffff00007fbab040
[ 2.779217] x14: ffff00007fb918c0 x13: 0000000000000000 x12: 000000000000017a
[ 2.786341] x11: 0000000000000001 x10: 0000000000000a90 x9 : ffff80008324bd00
[ 2.793465] x8 : ffff0000050f0af0 x7 : ffff00007fbaa840 x6 : 0000000000000031
[ 2.800589] x5 : 000000000000017a x4 : 0000000000000002 x3 : 0000000000000002
[ 2.807713] x2 : ffff80008324bd3a x1 : 0000000000000010 x0 : 0000000000000000
[ 2.814838] Call trace:
[ 2.817273] tcpci_irq+0x38/0x318
[ 2.820583] _tcpci_irq+0x14/0x20
[ 2.823885] irq_thread_fn+0x2c/0xa8
[ 2.827456] irq_thread+0x16c/0x2f4
[ 2.830940] kthread+0x110/0x114
[ 2.834164] ret_from_fork+0x10/0x20
[ 2.837738] Code: f9426420 f9001fe0 d2800000 52800201 (f9400a60)
This may happen on shared irq case. Such as two Type-C ports share one
irq. After the first port finished tcpci_register_port(), it may trigger
interrupt. However, if the interrupt comes by chance the 2nd port finishes
devm_request_threaded_irq(), the 2nd port interrupt handler will run at
first. Then the above issue happens due to tcpci is still a NULL pointer
in tcpci_irq() when dereference to regmap.
devm_request_threaded_irq()
<-- port1 irq comes
disable_irq(client->irq);
tcpci_register_port()
This will restore the logic to the state before commit (77e85107a771 "usb:
typec: tcpci: support edge irq").
However, moving tcpci_register_port() earlier creates a problem when use
edge irq because tcpci_init() will be called before
devm_request_threaded_irq(). The tcpci_init() writes the ALERT_MASK to
the hardware to tell it to start generating interrupts but we're not ready
to deal with them yet, then the ALERT events may be missed and ALERT line
will not recover to high level forever. To avoid the issue, this will also
set ALERT_MASK register after devm_request_threaded_irq() return.
Fixes: 77e85107a771 ("usb: typec: tcpci: support edge irq")
Cc: stable <stable@kernel.org>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20241218095328.2604607-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
crash caused by port being null
Considering that in some extreme cases, when performing the
unbinding operation, gserial_disconnect has cleared gser->ioport,
which triggers gadget reconfiguration, and then calls gs_read_complete,
resulting in access to a null pointer. Therefore, ep is disabled before
gserial_disconnect sets port to null to prevent this from happening.
Call trace:
gs_read_complete+0x58/0x240
usb_gadget_giveback_request+0x40/0x160
dwc3_remove_requests+0x170/0x484
dwc3_ep0_out_start+0xb0/0x1d4
__dwc3_gadget_start+0x25c/0x720
kretprobe_trampoline.cfi_jt+0x0/0x8
kretprobe_trampoline.cfi_jt+0x0/0x8
udc_bind_to_driver+0x1d8/0x300
usb_gadget_probe_driver+0xa8/0x1dc
gadget_dev_desc_UDC_store+0x13c/0x188
configfs_write_iter+0x160/0x1f4
vfs_write+0x2d0/0x40c
ksys_write+0x7c/0xf0
__arm64_sys_write+0x20/0x30
invoke_syscall+0x60/0x150
el0_svc_common+0x8c/0xf8
do_el0_svc+0x28/0xa0
el0_svc+0x24/0x84
Fixes: c1dca562be8a ("usb gadget: split out serial core")
Cc: stable <stable@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Link: https://lore.kernel.org/r/TYUPR06MB621733B5AC690DBDF80A0DCCD2042@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
the error path of .probe()
Current implementation of ci_hdrc_imx_driver does not decrement the
refcount of the device obtained in usbmisc_get_init_data(). Add a
put_device() call in .remove() and in .probe() before returning an
error.
This bug was found by an experimental static analysis tool that I am
developing.
Cc: stable <stable@kernel.org>
Fixes: f40017e0f332 ("chipidea: usbmisc_imx: Add USB support for VF610 SoCs")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241216015539.352579-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current implementation of the ucsi glink client connector_status()
callback is only relying on the state of the gpio. This means that even
when the cable is unplugged, the orientation propagated to the switches
along the graph is "orientation normal", instead of "orientation none",
which would be the correct one in this case.
One of the Qualcomm DP-USB PHY combo drivers, which needs to be aware of
the orientation change, is relying on the "orientation none" to skip
the reinitialization of the entire PHY. Since the ucsi glink client
advertises "orientation normal" even when the cable is unplugged, the
mentioned PHY is taken down and reinitialized when in fact it should be
left as-is. This triggers a crash within the displayport controller driver
in turn, which brings the whole system down on some Qualcomm platforms.
Propagating "orientation none" from the ucsi glink client on the
connector_status() callback hides the problem of the mentioned PHY driver
away for now. But the "orientation none" is nonetheless the correct one
to be used in this case.
So propagate the "orientation none" instead when the connector status
flags says cable is disconnected.
Fixes: 76716fd5bf09 ("usb: typec: ucsi: glink: move GPIO reading into connector_status callback")
Cc: stable <stable@kernel.org> # 6.10
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241212-usb-typec-ucsi-glink-add-orientation-none-v2-1-db5a50498a77@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit c033563220e0f7a8
("usb: gadget: configfs: Attach arbitrary strings to cdev")
a user can provide extra string descriptors to a USB gadget via configfs.
For "manufacturer", "product", "serialnumber", setting the string via
configfs ignores a trailing LF.
For the arbitrary strings the LF was not ignored.
This patch ignores a trailing LF to make this consistent with the existing
behavior for "manufacturer", ... string descriptors.
Fixes: c033563220e0 ("usb: gadget: configfs: Attach arbitrary strings to cdev")
Cc: stable <stable@kernel.org>
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Link: https://lore.kernel.org/r/20241212154114.29295-1-ingo.rohloff@lauterbach.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the regression introduced by commit d8c6edfa3f4e ("USB:
usblp: don't call usb_set_interface if there's a single alt"),
which causes that unsupported protocols can also be set via
ioctl when the num_altsetting of the device is 1.
Move the check for protocol support to the earlier stage.
Fixes: d8c6edfa3f4e ("USB: usblp: don't call usb_set_interface if there's a single alt")
Cc: stable <stable@kernel.org>
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Link: https://lore.kernel.org/r/20241212143852.671889-1-jerrysteve1101@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently afunc_bind sets std_ac_if_desc.bNumEndpoints to 1 if
controls (mute/volume) are enabled. During next afunc_bind call,
bNumEndpoints would be unchanged and incorrectly set to 1 even
if the controls aren't enabled.
Fix this by resetting the value of bNumEndpoints to 0 on every
afunc_bind call.
Fixes: eaf6cbe09920 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20241211115915.159864-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
max_contaminant_read_resistance_kohm()
If max_contaminant_read_adc_mv() fails, then return the error code. Don't
return zero.
Fixes: 02b332a06397 ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/f1bf3768-419e-40dd-989c-f7f455d6c824@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
XHCI_SKIP_PHY_INIT property
The source of quirk XHCI_SKIP_PHY_INIT comes from xhci_plat_priv.quirks or
software node property. This will set skip_phy_initialization if software
node also has XHCI_SKIP_PHY_INIT property.
Fixes: a6cd2b3fa894 ("usb: host: xhci-plat: Parse xhci-missing_cas_quirk and apply quirk")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241209111423.4085548-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Runtime PM documentation (Section 5) mentions, during remove()
callbacks, drivers should undo the runtime PM changes done in
probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc. Hence add missing
function to disable autosuspend on dwc3-am62 driver unbind.
Fixes: e8784c0aec03 ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209105728.3216872-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Before writing a new value to the register, the old value needs to be
masked out for the new value to be programmed as intended, because at
least in some cases the reset value of that field is 0xf (max value).
At the moment, the dwc3 core initialises the threshold to the maximum
value (0xf), with the option to override it via a DT. No upstream DTs
seem to override it, therefore this commit doesn't change behaviour for
any upstream platform. Nevertheless, the code should be fixed to have
the desired outcome.
Do so.
Fixes: 80caf7d21adc ("usb: dwc3: add lpm erratum support")
Cc: stable@vger.kernel.org # 5.10+ (needs adjustment for 5.4)
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209-dwc3-nyet-fix-v2-1-02755683345b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The cc1 and cc2 status returned by tcpci_get_cc() may be TYPEC_CC_OPEN
or TYPEC_CC_RA. So don't assume it's just TYPEC_CC_RD or TYPEC_CC_RP_*.
This will let local port present Rd on CC only when cc1/cc2 status is
TYPEC_CC_RP_*.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211105753.1205312-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
remove redundant semicolon in LPIOC_SOFT_RESET to
fix the incorrect macro expansion syntax.
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Link: https://lore.kernel.org/r/20241213145314.785616-1-jerrysteve1101@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_register_driver() uses complex goto statements to handle simple error
cases, move down the goto label 'out' a bit to
- Simplify goto logic
- Leverage pr_err() prompt for driver registering failure.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241212-fix_usb-v1-1-300eb440c753@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If controller looses power during PM suspend then re-initialize
it. We use the DEBUG_CFG register to track if controller lost power
or was reset in PM suspend.
Move all initialization code into dwc3_ti_init() so it can be re-used.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241212-am62-dwc3-io-ddr-v3-1-10b95cd7e9c0@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds documentation for two USB functions:
- usb_otg_state_string(), which returns a human-readable name for OTG
states and
- usb_get_dr_mode_from_string(), which returns the dual role mode for a
given string.
Signed-off-by: Lucy Mielke <lucymielke@icloud.com>
Link: https://lore.kernel.org/r/6nvegfmo6d5ak4soaf5nyifsaasfts4qlsnnpsd4sgpnikc2jd@amfmgdr5n3bi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the function pmc_mux_port_debugfs_init() the buffer for
the name of the port is limited to six bytes. That makes the
compiler think that the output of "port%d" may be truncated.
That can't actually happen as the interface can support
maximum of eight ports. To make the compiler happy just
increase the buffer to where the warning goes away.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412031437.vX580pxx-lkp@intel.com/
Cc: Rajat Khandelwal <rajat.khandelwal@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241205113919.1182673-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It generally is not OK to use acpi_status and/or AE_ error codes
without CONFIG_ACPI and they really only should be used in
drivers/acpi/ (and not everywhere in there for that matter).
So acpi_get_physical_device_location() needs to be redefined to return
something different from acpi_status (preferably bool) in order to be
used in !CONFIG_ACPI code.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20241216-fix-ipu-v5-1-3d6b35ddce7b@chromium.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The source and destination rings were incorrectly assigned during the ring
linking process. The "source" ring, which contains the new segments,
was not spliced into the "destination" ring, leading to incorrect ring
expansion.
Fixes: fe688e500613 ("usb: xhci: refactor xhci_link_rings() to use source and destination rings")
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Closes: https://lore.kernel.org/lkml/CAAJw_ZtppNqC9XA=-WVQDr+vaAS=di7jo15CzSqONeX48H75MA@mail.gmail.com/
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHC hosts from several vendors have the same issue where endpoints start
so slowly that a later queued 'Stop Endpoint' command may complete before
endpoint is up and running.
The 'Stop Endpoint' command fails with context state error as the endpoint
still appears as stopped.
See commit 42b758137601 ("usb: xhci: Limit Stop Endpoint retries") for
details
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.13-rc3
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FE910C04 rmnet compositions
USB: serial: option: add MediaTek T7XX compositions
USB: serial: option: add Netprisma LCUK54 modules for WWAN Ready
USB: serial: option: add MeiG Smart SLM770A
USB: serial: option: add TCL IK512 MBIM & ECM
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes for some reported issues.
Included in here are:
- typec driver bugfixes
- u_serial gadget driver bugfix for much reported and discussed issue
- dwc2 bugfixes
- midi gadget driver bugfix
- ehci-hcd driver bugfix
- other small bugfixes
All of these have been in linux-next for over a week with no reported
issues"
* tag 'usb-6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: ucsi: Fix connector status writing past buffer size
usb: typec: ucsi: Fix completion notifications
usb: dwc2: Fix HCD port connection race
usb: dwc2: hcd: Fix GetPortStatus & SetPortFeature
usb: dwc2: Fix HCD resume
usb: gadget: u_serial: Fix the issue that gs_start_io crashed due to accessing null pointer
usb: misc: onboard_usb_dev: skip suspend/resume sequence for USB5744 SMBus support
usb: dwc3: xilinx: make sure pipe clock is deselected in usb2 only mode
usb: core: hcd: only check primary hcd skip_phy_initialization
usb: gadget: midi2: Fix interpretation of is_midi1 bits
usb: dwc3: imx8mp: fix software node kernel dump
usb: typec: anx7411: fix OF node reference leaks in anx7411_typec_switch_probe()
usb: typec: anx7411: fix fwnode_handle reference leak
usb: host: max3421-hcd: Correctly abort a USB request.
dt-bindings: phy: imx8mq-usb: correct reference to usb-switch.yaml
usb: ehci-hcd: fix call balance of clocks handling routines
|
|
Add the following Telit FE910C04 compositions:
0x10c0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 13 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c4: rmnet + tty (AT) + tty (AT) + tty (diag)
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c4 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c8: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c8 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add the MediaTek T7XX compositions:
T: Bus=03 Lev=01 Prnt=01 Port=05 Cnt=01 Dev#= 74 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=7129 Rev= 0.01
S: Manufacturer=MediaTek Inc.
S: Product=USB DATA CARD
S: SerialNumber=004402459035402
C:* #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
-------------------------------
| If Number | Function |
-------------------------------
| 2 | USB AP Log Port |
-------------------------------
| 3 | USB AP GNSS Port|
-------------------------------
| 4 | USB AP META Port|
-------------------------------
| 5 | ADB port |
-------------------------------
| 6 | USB MD AT Port |
------------------------------
| 7 | USB MD META Port|
-------------------------------
| 8 | USB NTZ Port |
-------------------------------
| 9 | USB Debug port |
-------------------------------
Signed-off-by: Jack Wu <wojackbb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
LCUK54-WRD's pid/vid
0x3731/0x010a
0x3731/0x010c
LCUK54-WWD's pid/vid
0x3731/0x010b
0x3731/0x010d
Above products use the exact same interface layout and option
driver:
MBIM + GNSS + DIAG + NMEA + AT + QDSS + DPL
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=3731 ProdID=0101 Rev= 5.04
S: Manufacturer=NetPrisma
S: Product=LCUK54-WRD
S: SerialNumber=feeba631
C:* #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Mank Wang <mank.wang@netprisma.com>
[ johan: use lower case hex notation ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Update the USB serial option driver to support MeiG Smart SLM770A.
ID 2dee:4d57 Marvell Mobile Composite Device Bus
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2dee ProdID=4d57 Rev= 1.00
S: Manufacturer=Marvell
S: Product=Mobile Composite Device Bus
C:* #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=88(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0e(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Tested successfully connecting to the Internet via rndis interface after
dialing via AT commands on If#=3 or If#=4.
Not sure of the purpose of the other serial interfaces.
Signed-off-by: Michal Hrusecky <michal.hrusecky@turris.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add the following TCL IK512 compositions:
0x0530: Modem + Diag + AT + MBIM
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=10000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=1bbb ProdID=0530 Rev=05.04
S: Manufacturer=TCL
S: Product=TCL 5G USB Dongle
S: SerialNumber=3136b91a
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
0x0640: ECM + Modem + Diag + AT
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=10000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=1bbb ProdID=0640 Rev=05.04
S: Manufacturer=TCL
S: Product=TCL 5G USB Dongle
S: SerialNumber=3136b91a
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
Signed-off-by: Daniel Swanemar <d.swanemar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Improve naming consistency with the .sdev_prep() and .sdev_destroy()
methods by renaming .device_configure() into .sdev_configure().
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into
.sdev_destroy(). The new names make it clear that these are actions on
SCSI devices. Make this change in the SCSI core, SCSI drivers and also
in the ATA drivers. No functionality has been changed.
This patch has been created as follows:
* Change the text "slave_alloc" into "sdev_init" in all source files
except those in drivers/net/ and Documentation/.
* Change the text "slave_destroy" into "sdev_destroy" in all source
files except those in drivers/net/ and Documentation/.
* Rename lpfc_no_slave() into lpfc_no_sdev().
* Manually adjust whitespace where necessary to restore vertical
alignment (dc395x driver and include/linux/libata.h).
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The meaning of this value is already used in several places,
but with constant values and comments to explain it separately.
It's better to have a central place to do this then use the macro
in those places for better readability.
Signed-off-by: Dingyan Li <18500469033@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241030083858.46907-1-18500469033@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Similar to commit 65c4c9447bfc ("usb: typec: ucsi: Fix a missing bits to
bytes conversion in ucsi_init()"), there was a missing conversion from
bits to bytes. Here the outcome is worse though: since the value is
lower than UCSI_MAX_DATA_LENGTH, instead of bailing out with an error,
it writes past the buffer size.
The error is then seen in other places like below:
Oops: general protection fault, probably for non-canonical address 0x891e812cd0ed968: 0000 [#1] PREEMPT SMP NOPTI
CPU: 3 UID: 110 PID: 906 Comm: prometheus-node Not tainted 6.13.0-rc1-xe #1
Hardware name: Intel Corporation Lunar Lake Client Platform/LNL-M LP5 RVP1, BIOS LNLMFWI1.R00.3222.D84.2410171025 10/17/2024
RIP: 0010:power_supply_get_property+0x3e/0xe0
Code: 85 c0 7e 4f 4c 8b 07 89 f3 49 89 d4 49 8b 48 20 48 85 c9 74 72 49 8b 70 18 31 d2 31 c0 eb 0b 83 c2 01 48 63 c2 48 39 c8 73 5d <3b> 1c 86 75 f0 49 8b 40 28 4c 89 e2 89 de ff d0 0f 1f 00 5b 41 5c
RSP: 0018:ffffc900017dfa50 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000011 RCX: c963b02c06092008
RDX: 0000000000000000 RSI: 0891e812cd0ed968 RDI: ffff888121dd6800
RBP: ffffc900017dfa68 R08: ffff88810a4024b8 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffc900017dfa78
R13: ffff888121dd6800 R14: ffff888138ad2c00 R15: ffff88810c57c528
FS: 00007713a2ffd6c0(0000) GS:ffff88846f380000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000c0004b1000 CR3: 0000000121ce8003 CR4: 0000000000f72ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
? show_regs+0x6c/0x80
? die_addr+0x37/0xa0
? exc_general_protection+0x1c1/0x440
? asm_exc_general_protection+0x27/0x30
? power_supply_get_property+0x3e/0xe0
power_supply_hwmon_read+0x50/0xe0
hwmon_attr_show+0x46/0x170
dev_attr_show+0x1a/0x70
sysfs_kf_seq_show+0xaa/0x120
kernfs_seq_show+0x41/0x60
Just use the buffer size as argument to fix it.
Fixes: 226ff2e681d0 ("usb: typec: ucsi: Convert connector specific commands to bitmaps")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reported-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Closes: https://lore.kernel.org/all/SJ1PR11MB6129CCD82CD78D8EE6E27EF4B9362@SJ1PR11MB6129.namprd11.prod.outlook.com/
Suggested-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Link: https://lore.kernel.org/r/20241203200010.2821132-1-lucas.demarchi@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
OPM PPM LPM
| 1.send cmd | |
|-------------------------->| |
| |-- |
| | | 2.set busy bit in CCI |
| |<- |
| 3.notify the OPM | |
|<--------------------------| |
| | 4.send cmd to be executed |
| |-------------------------->|
| | |
| | 5.cmd completed |
| |<--------------------------|
| | |
| |-- |
| | | 6.set cmd completed |
| |<- bit in CCI |
| | |
| 7.notify the OPM | |
|<--------------------------| |
| | |
| 8.handle notification | |
| from point 3, read CCI | |
|<--------------------------| |
| | |
When the PPM receives command from the OPM (p.1) it sets the busy bit
in the CCI (p.2), sends notification to the OPM (p.3) and forwards the
command to be executed by the LPM (p.4). When the PPM receives command
completion from the LPM (p.5) it sets command completion bit in the CCI
(p.6) and sends notification to the OPM (p.7). If command execution by
the LPM is fast enough then when the OPM starts handling the notification
from p.3 in p.8 and reads the CCI value it will see command completion bit
set and will call complete(). Then complete() might be called again when
the OPM handles notification from p.7.
This fix replaces test_bit() with test_and_clear_bit()
in ucsi_notify_common() in order to call complete() only
once per request.
This fix also reinitializes completion variable in
ucsi_sync_control_common() before a command is sent.
Fixes: 584e8df58942 ("usb: typec: ucsi: extract common code for command handling")
Cc: stable@vger.kernel.org
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241203102318.3386345-1-ukaszb@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Raspberry Pis without onboard USB hub frequent device reconnects
can trigger a interrupt storm after DWC2 entered host clock gating.
This is caused by a race between _dwc2_hcd_suspend() and the port
interrupt, which sets port_connect_status. The issue occurs if
port_connect_status is still 1, but there is no connection anymore:
usb 1-1: USB disconnect, device number 25
dwc2 3f980000.usb: _dwc2_hcd_suspend: port_connect_status: 1
dwc2 3f980000.usb: Entering host clock gating.
Disabling IRQ #66
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.0-gc1bb81b13202-dirty #322
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1d01f20 to 0xc1d01f68)
1f20: 0004ef3c 00000001 00000000 00000000 c1d09780 c1f6bb5c c1d04e54 c1c60ca8
1f40: c1d04e94 00000000 00000000 c1d092a8 c1f6af20 c1d01f70 c1211b98 c1212f40
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<e3a25c00>] dwc2_handle_common_intr
[<58bf98a3>] usb_hcd_irq
Disabling IRQ #66
So avoid this by reading the connection status directly.
Fixes: 113f86d0c302 ("usb: dwc2: Update partial power down entering by system suspend")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-4-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Rasperry Pis without onboard USB hub the power cycle during
power connect init only disable the port but never enabled it again:
usb usb1-port1: attempt power cycle
The port relevant part in dwc2_hcd_hub_control() is skipped in case
port_connect_status = 0 under the assumption the core is or will be soon
in device mode. But this assumption is wrong, because after ClearPortFeature
USB_PORT_FEAT_POWER the port_connect_status will also be 0 and
SetPortFeature (incl. USB_PORT_FEAT_POWER) will be a no-op.
Fix the behavior of dwc2_hcd_hub_control() by replacing the
port_connect_status check with dwc2_is_device_mode().
Link: https://github.com/raspberrypi/linux/issues/6247
Fixes: 7359d482eb4d ("staging: HCD files for the DWC2 driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Raspberry Pi can suffer on interrupt storms on HCD resume. The dwc2
driver sometimes misses to enable HCD_FLAG_HW_ACCESSIBLE before re-enabling
the interrupts. This causes a situation where both handler ignore a incoming
port interrupt and force the upper layers to disable the dwc2 interrupt
line. This leaves the USB interface in a unusable state:
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.10.0-rc3
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1b01f20 to 0xc1b01f68)
1f20: 0005c0d4 00000001 00000000 00000000 c1b09780 c1d6b32c c1b04e54 c1a5eae8
1f40: c1b04e90 00000000 00000000 00000000 c1d6a8a0 c1b01f70 c11d2da8 c11d4160
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<f539e0f4>] dwc2_handle_common_intr
[<75cd278b>] usb_hcd_irq
Disabling IRQ #66
So enable the HCD_FLAG_HW_ACCESSIBLE flag in case there is a port
connection.
Fixes: c74c26f6e398 ("usb: dwc2: Fix partial power down exiting by system resume")
Closes: https://lore.kernel.org/linux-usb/3fd0c2fb-4752-45b3-94eb-42352703e1fd@gmx.net/T/
Link: https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
accessing null pointer
Considering that in some extreme cases,
when u_serial driver is accessed by multiple threads,
Thread A is executing the open operation and calling the gs_open,
Thread B is executing the disconnect operation and calling the
gserial_disconnect function,The port->port_usb pointer will be set to NULL.
E.g.
Thread A Thread B
gs_open() gadget_unbind_driver()
gs_start_io() composite_disconnect()
gs_start_rx() gserial_disconnect()
... ...
spin_unlock(&port->port_lock)
status = usb_ep_queue() spin_lock(&port->port_lock)
spin_lock(&port->port_lock) port->port_usb = NULL
gs_free_requests(port->port_usb->in) spin_unlock(&port->port_lock)
Crash
This causes thread A to access a null pointer (port->port_usb is null)
when calling the gs_free_requests function, causing a crash.
If port_usb is NULL, the release request will be skipped as it
will be done by gserial_disconnect.
So add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port_usb.
Call trace:
gs_start_io+0x164/0x25c
gs_open+0x108/0x13c
tty_open+0x314/0x638
chrdev_open+0x1b8/0x258
do_dentry_open+0x2c4/0x700
vfs_open+0x2c/0x3c
path_openat+0xa64/0xc60
do_filp_open+0xb8/0x164
do_sys_openat2+0x84/0xf0
__arm64_sys_openat+0x70/0x9c
invoke_syscall+0x58/0x114
el0_svc_common+0x80/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x38/0x68
Fixes: c1dca562be8a ("usb gadget: split out serial core")
Cc: stable@vger.kernel.org
Suggested-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Acked-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/TYUPR06MB62178DC3473F9E1A537DCD02D2362@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
support
USB5744 SMBus initialization is done once in probe() and doing it in resume
is not supported so avoid going into suspend and reset the HUB.
There is a sysfs property 'always_powered_in_suspend' to implement this
feature but since default state should be set to a working configuration
so override this property value.
It fixes the suspend/resume testcase on Kria KR260 Robotics Starter Kit.
Fixes: 6782311d04df ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Cc: stable@vger.kernel.org
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1733165302-1694891-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the USB3 PHY is not defined in the Linux device tree, there could
still be a case where there is a USB3 PHY active on the board and enabled
by the first stage bootloader. If serdes clock is being used then the USB
will fail to enumerate devices in 2.0 only mode.
To solve this, make sure that the PIPE clock is deselected whenever the
USB3 PHY is not defined and guarantees that the USB2 only mode will work
in all cases.
Fixes: 9678f3361afc ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: stable@vger.kernel.org
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/1733163111-1414816-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Before commit 53a2d95df836 ("usb: core: add phy notify connect and
disconnect"), phy initialization will be skipped even when shared hcd
doesn't set skip_phy_initialization flag. However, the situation is
changed after the commit. The hcd.c will initialize phy when add shared
hcd. This behavior is unexpected for some platforms which will handle phy
initialization by themselves. To avoid the issue, this will only check
skip_phy_initialization flag of primary hcd since shared hcd normally
follow primary hcd setting.
Fixes: 53a2d95df836 ("usb: core: add phy notify connect and disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241105090120.2438366-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The UMP Function Block info m1.0 field (represented by is_midi1 sysfs
entry) is an enumeration from 0 to 2, while the midi2 gadget driver
incorrectly copies it to the corresponding snd_ump_block_info.flags
bits as-is. This made the wrong bit flags set when m1.0 = 2.
This patch corrects the wrong interpretation of is_midi1 bits.
Fixes: 29ee7a4dddd5 ("usb: gadget: midi2: Add configfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20241127070213.8232-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When unbind and bind the device again, kernel will dump below warning:
[ 173.972130] sysfs: cannot create duplicate filename '/devices/platform/soc/4c010010.usb/software_node'
[ 173.981564] CPU: 2 UID: 0 PID: 536 Comm: sh Not tainted 6.12.0-rc6-06344-g2aed7c4a5c56 #144
[ 173.989923] Hardware name: NXP i.MX95 15X15 board (DT)
[ 173.995062] Call trace:
[ 173.997509] dump_backtrace+0x90/0xe8
[ 174.001196] show_stack+0x18/0x24
[ 174.004524] dump_stack_lvl+0x74/0x8c
[ 174.008198] dump_stack+0x18/0x24
[ 174.011526] sysfs_warn_dup+0x64/0x80
[ 174.015201] sysfs_do_create_link_sd+0xf0/0xf8
[ 174.019656] sysfs_create_link+0x20/0x40
[ 174.023590] software_node_notify+0x90/0x100
[ 174.027872] device_create_managed_software_node+0xec/0x108
...
The '4c010010.usb' device is a platform device created during the initcall
and is never removed, which causes its associated software node to persist
indefinitely.
The existing device_create_managed_software_node() does not provide a
corresponding removal function.
Replace device_create_managed_software_node() with the
device_add_software_node() and device_remove_software_node() pair to ensure
proper addition and removal of software nodes, addressing this issue.
Fixes: a9400f1979a0 ("usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241126032841.2458338-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The refcounts of the OF nodes obtained by of_get_child_by_name() calls
in anx7411_typec_switch_probe() are not decremented. Replace them with
device_get_named_child_node() calls and store the return values to the
newly created fwnode_handle fields in anx7411_data, and call
fwnode_handle_put() on them in the error path and in the unregister
functions.
Fixes: e45d7337dc0e ("usb: typec: anx7411: Use of_get_child_by_name() instead of of_find_node_by_name()")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241126014909.3687917-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
