Age | Commit message (Collapse) | Author |
|
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
USB-serial drivers must not be unbound from their ports before the
corresponding USB driver is unbound from the parent interface so
suppress the bind and unbind attributes.
Unbinding a serial driver while it's port is open is a sure way to
trigger a crash as any driver state is released on unbind while port
hangup is handled on the parent USB interface level. Drivers for
multiport devices where ports share a resource such as an interrupt
endpoint also generally cannot handle individual ports going away.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.5-3
* Fix Interrupt Status register offset for Intel Sunrisepoint PCH-H.
The following is an automated git shortlog grouped by driver:
sunrisepoint:
- Add missing Interrupt Status register offset
|
|
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 99f83c9c9ac9 ("[PATCH] USB: add driver for Keyspan Digital Remote")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 2.6.13
Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the onkey driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.
This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.
This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This reverts commit a284e11c371e446371675668d8c8120a27227339.
This causes problems (drifting cursor) with at least the F11 function that
reads more than 32 bytes.
The real issue is in the F54 driver, and so this should be fixed there, and
not in rmi_smbus.c.
So first revert this bad commit, then fix the real problem in F54 in another
patch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Fixes: a284e11c371e ("Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115124819.3191024-2-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also
some reverts of double-applied patches that brings the diffstat up a
bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC)
Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
ARM: omap2plus: select RESET_CONTROLLER
ARM: davinci: select CONFIG_RESET_CONTROLLER
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
ARM: dts: mmp3: Fix the TWSI ranges
clk: mmp2: Fix the order of timer mux parents
ARM: mmp: do not divide the clock rate
arm64: dts: rockchip: Fix IR on Beelink A1
optee: Fix multi page dynamic shm pool alloc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Second collection of clk fixes for the next release.
This one includes a fix for PM on TI SoCs with sysc devices and fixes
a bunch of clks that are stuck always enabled on Qualcomm SDM845 SoCs.
Allwinner SoCs get the usual set of fixes too, mostly correcting
drivers to have the right bits that match the hardware.
There's also a Samsung and Tegra fix in here to mark a clk critical
and avoid a double free.
And finally there's a fix for critical clks that silences a big
warning splat about trying to enable a clk that couldn't even be
prepared"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: dra7-atl: Remove pm_runtime_irq_safe()
clk: qcom: gcc-sdm845: Add missing flag to votable GDSCs
clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order
clk: sunxi-ng: h6-r: Simplify R_APB1 clock definition
clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock
clk: Don't try to enable critical clocks if prepare failed
clk: tegra: Fix double-free in tegra_clk_init()
clk: samsung: exynos5420: Keep top G3D clocks enabled
clk: sunxi-ng: r40: Allow setting parent rate for external clock outputs
clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a coding mistake in the teo cpuidle governor causing data to be
written beyond the last array element (Ikjoon Jang)"
* tag 'pm-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: teo: Fix intervals[] array indexing bug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform fix from Benson Leung:
"One fix in the wilco_ec keyboard backlight driver to allow the EC
driver to continue loading in the absence of a backlight module"
* tag 'tag-chrome-platform-fixes-for-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: Fix keyboard backlight probing
|
|
Add support for Quectel RM500Q in QDL mode.
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 24 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0800 Rev= 0.00
S: Manufacturer=Qualcomm CDMA Technologies MSM
S: Product=QUSB_BULK_SN:xxxxxxxx
S: SerialNumber=xxxxxxxx
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=10 Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
It is assumed that the ZLP flag required for other Qualcomm-based
5G devices also applies to Quectel RM500Q.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Commit 7ad2ed1dfcbe inadvertently mixed up a quirk flag's name and
broke SDR50 tuning override. Use correct NVQUIRK_ name.
Fixes: 7ad2ed1dfcbe ("mmc: tegra: enable UHS-I modes")
Cc: <stable@vger.kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/9aff1d859935e59edd81e4939e40d6c55e0b55f6.1578390388.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The only callers of the function lapbeth_get_x25_dev()
are lapbeth_rcv() and lapbeth_device_event().
lapbeth_rcv() uses rcu_read_lock() whereas lapbeth_device_event()
is called with RTNL held (As mentioned in the comments).
Therefore, pass lockdep_rtnl_is_held() as cond argument in
list_for_each_entry_rcu();
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik04@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building with PROVE_LOCKING=y, lockdep shows the following
dump message.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().
Fixes: 7200f2e3c9e2 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.
This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I missed the fact that macvlan_broadcast() can be used both
in RX and TX.
skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()
Fixes: 96cc4b69581d ("macvlan: do not assume mac_header is set in macvlan_broadcast()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jurgen Van Ham <juvanham@gmail.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Command Queuing was enabled completely for J721e controllers which lead
to partial enablement even for Am65x. Complete CQ implementation for
AM65x by adding the irq callback.
Fixes: f545702b74f9 ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The tuning data is leftover in the buffer after tuning. This can cause
issues in future data commands, especially with CQHCI. Reset the command
and data lines after tuning to continue from a clean state.
Fixes: 41fd4caeb00b ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The MMC/SD controllers on am65x and j721e don't in fact detect the write
protect line as inverted. No issues were detected because of this
because the sdwp line is not connected on any of the evms. Fix this by
removing the flag.
Fixes: 1accbced1c32 ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-2-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Logical block size has type unsigned short. That means that it can be at
most 32768. However, there are architectures that can run with 64k pages
(for example arm64) and on these architectures, it may be possible to
create block devices with 64k block size.
For exmaple (run this on an architecture with 64k pages):
Mount will fail with this error because it tries to read the superblock using 2-sector
access:
device-mapper: writecache: I/O is not aligned, sector 2, size 1024, block size 65536
EXT4-fs (dm-0): unable to read superblock
This patch changes the logical block size from unsigned short to unsigned
int to avoid the overflow.
Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Tom Hatskevich reported that we look up "iocp" then, in the called
functions we do a second copy_from_user() and look it up again.
The problem that could cause is:
drivers/message/fusion/mptctl.c
674 /* All of these commands require an interrupt or
675 * are unknown/illegal.
676 */
677 if ((ret = mptctl_syscall_down(iocp, nonblock)) != 0)
^^^^
We take this lock.
678 return ret;
679
680 if (cmd == MPTFWDOWNLOAD)
681 ret = mptctl_fw_download(arg);
^^^
Then the user memory changes and we look up "iocp" again but a different
one so now we are holding the incorrect lock and have a race condition.
682 else if (cmd == MPTCOMMAND)
683 ret = mptctl_mpt_command(arg);
The security impact of this bug is not as bad as it could have been
because these operations are all privileged and root already has
enormous destructive power. But it's still worth fixing.
This patch passes the "iocp" pointer to the functions to avoid the
second lookup. That deletes 100 lines of code from the driver so
it's a nice clean up as well.
Link: https://lore.kernel.org/r/20200114123414.GA7957@kadam
Reported-by: Tom Hatskevich <tom2001tom.23@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 0ed881027690 ("scsi: storvsc: setup 1:1 mapping between hardware
queue and CPU queue") introduced a regression for disks attached to
IDE. For these disks the host VSP only offers one VMBUS channel. Setting
multiple queues can overload the VMBUS channel and result in performance
drop for high queue depth workload on system with large number of CPUs.
Fix it by leaving the number of hardware queues to 1 (default value) for
IDE disks.
Fixes: 0ed881027690 ("scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue")
Link: https://lore.kernel.org/r/1578960516-108228-1-git-send-email-longli@linuxonhyperv.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
gcc -O3 warns that some local variables are not properly initialized:
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_hang_notify':
drivers/scsi/fnic/vnic_dev.c:511:16: error: 'a0' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[0] = *a0;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:6: note: 'a0' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:10: note: 'a1' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_mac_addr':
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:698:10: note: 'a1' was declared here
u64 a0, a1;
^~
Apparently the code relies on the local variables occupying adjacent memory
locations in the same order, but this is of course not guaranteed.
Use an array of two u64 variables where needed to make it work correctly.
I suspect there is also an endianness bug here, but have not digged in deep
enough to be sure.
Fixes: 5df6d737dd4b ("[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA")
Fixes: mmtom ("init/Kconfig: enable -O3 for all arches")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200107201602.4096790-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.5-2020-01-15:
- Update golden settings for renoir
- eDP fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115235141.4149-1-alexander.deucher@amd.com
|
|
read_current_link_settings_on_detect() on eDP 1.4+ may use the
edp_supported_link_rates table which is set up by
detect_edp_sink_caps(), so that function needs to be called first.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Martin Leung <martin.leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Update mmSDMA0_UTCL1_WATERMK golden setting for renoir.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
To account for parts of the chip that are "harvested" (disabled) due to
silicon flaws, caches on some AMD GPUs must be initialized before ATS is
enabled.
ATS is normally enabled by the IOMMU driver before the GPU driver loads, so
this cache initialization would have to be done in a quirk, but that's too
complex to be practical.
For Navi14 (device ID 0x7340), this initialization is done by the VBIOS,
but apparently some boards went to production with an older VBIOS that
doesn't do it. Disable ATS for those boards.
Link: https://lore.kernel.org/r/20200114205523.1054271-3-alexander.deucher@amd.com
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1015
See-also: d28ca864c493 ("PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken")
See-also: 9b44b0b09dec ("PCI: Mark AMD Stoney GPU ATS as broken")
[bhelgaas: squash into one patch, simplify slightly, commit log]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
When HW does not support perfect filtering the feature will not be
enabled in the net_device. Add a check for this to prevent failures.
Fixes: 1b2250a04c1f ("net: stmmac: selftests: Add tests for VLAN Perfect Filtering")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.
Fixes: 94e18382003c ("net: stmmac: selftests: Add selftest for VLAN TX Offload")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Array utdm_info is declared as an array of MAX_HDLC_NUM (4) elements
however up to UCC_MAX_NUM (8) elements are potentially being written
to it. Currently we have an array out-of-bounds write error on the
last 4 elements. Fix this by making utdm_info UCC_MAX_NUM elements in
size.
Addresses-Coverity: ("Out-of-bounds write")
Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[Why]
Noticed this while testing MST with the 4 ports MST hub from
StarTech.com. Sometimes can't light up monitors normally and get the
error message as 'sideband msg build failed'.
Look into aux transactions, found out that source sometimes will send
out another down request before receiving the down reply of the
previous down request. On the other hand, in drm_dp_get_one_sb_msg(),
current code doesn't handle the interleaved replies case. Hence, source
can't build up message completely and can't light up monitors.
[How]
For good compatibility, enforce source to send out one down request at a
time. Add a flag, is_waiting_for_dwn_reply, to determine if the source
can send out a down request immediately or not.
- Check the flag before calling process_single_down_tx_qlock to send out
a msg
- Set the flag when successfully send out a down request
- Clear the flag when successfully build up a down reply
- Clear the flag when find erros during sending out a down request
- Clear the flag when find errors during building up a down reply
- Clear the flag when timeout occurs during waiting for a down reply
- Use drm_dp_mst_kick_tx() to try to send another down request in queue
at the end of drm_dp_mst_wait_tx_reply() (attempt to send out messages
in queue when errors occur)
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113093649.11755-1-Wayne.Lin@amd.com
|
|
kmemleak detects the following memory leak when hot removing
a network device:
unreferenced object 0xffff888083f63600 (size 256):
comm "kworker/0:1", pid 12, jiffies 4294831717 (age 1113.676s)
hex dump (first 32 bytes):
00 40 c7 33 80 88 ff ff 00 00 00 00 10 00 00 00 .@.3............
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
backtrace:
[<00000000d4a8f5be>] rndis_filter_device_add+0x117/0x11c0 [hv_netvsc]
[<000000009c02d75b>] netvsc_probe+0x5e7/0xbf0 [hv_netvsc]
[<00000000ddafce23>] vmbus_probe+0x74/0x170 [hv_vmbus]
[<00000000046e64f1>] really_probe+0x22f/0xb50
[<000000005cc35eb7>] driver_probe_device+0x25e/0x370
[<0000000043c642b2>] bus_for_each_drv+0x11f/0x1b0
[<000000005e3d09f0>] __device_attach+0x1c6/0x2f0
[<00000000a72c362f>] bus_probe_device+0x1a6/0x260
[<0000000008478399>] device_add+0x10a3/0x18e0
[<00000000cf07b48c>] vmbus_device_register+0xe7/0x1e0 [hv_vmbus]
[<00000000d46cf032>] vmbus_add_channel_work+0x8ab/0x1770 [hv_vmbus]
[<000000002c94bb64>] process_one_work+0x919/0x17d0
[<0000000096de6781>] worker_thread+0x87/0xb40
[<00000000fbe7397e>] kthread+0x333/0x3f0
[<000000004f844269>] ret_from_fork+0x3a/0x50
rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.
Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Intel Software Developer's Manual, volume 3, chapter 9.11.6 says:
"Note that the microcode update must be aligned on a 16-byte boundary
and the size of the microcode update must be 1-KByte granular"
When early-load Intel microcode is loaded from initramfs, userspace tool
'iucode_tool' has already 16-byte aligned those microcode bits in that
initramfs image. Image that was created something like this:
iucode_tool --write-earlyfw=FOO.cpio microcode-files...
However, when early-load Intel microcode is loaded from built-in
firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that
16-byte alignment is not guaranteed.
Fix this by forcing all built-in firmware BLOBs to 16-byte alignment.
[ If we end up having other firmware with much bigger alignment
requirements, we might need to introduce some method for the firmware
to specify it, this is the minimal "just increase the alignment a bit
to account for this one special case" patch - Linus ]
Signed-off-by: Jari Ruusu <jari.ruusu@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When handling devm_gpiod_get_optional() errors, free the memory already
allocated. This fixes Smatch warnings:
drivers/i2c/busses/i2c-iop3xx.c:437 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
drivers/i2c/busses/i2c-iop3xx.c:442 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
Fixes: fdb7e884ad61 ("i2c: iop: Use GPIO descriptors")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- Fix keyboard brightness control for ASUS laptops
- Better handling parameters of GPD pocket fan module to avoid
thermal shock
- Add IDs to PMC platform driver to support Intel Comet Lake
- Fix potential dead lock in Mellanox TM FIFO driver and ABI
documentation
* tag 'platform-drivers-x86-v5.5-3' of git://git.infradead.org/linux-platform-drivers-x86:
Documentation/ABI: Add missed attribute for mlxreg-io sysfs interfaces
Documentation/ABI: Fix documentation inconsistency for mlxreg-io sysfs interfaces
platform/x86: asus-wmi: Fix keyboard brightness cannot be set to 0
platform/x86: intel_pmc_core: update Comet Lake platform driver
platform/x86: GPD pocket fan: Allow somewhat lower/higher temperature limits
platform/x86: GPD pocket fan: Use default values when wrong modparams are given
platform/mellanox: fix potential deadlock in the tmfifo driver
platform/x86: intel-ips: Use the correct style for SPDX License Identifier
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a build problem for the hisilicon driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hisilicon/sec2 - Use atomics instead of __sync
|
|
One of the recent Tegra I2C commits made a change that resumes runtime PM
during driver's probe, but it missed to put the RPM in a case of error.
Note that it's not correct to use pm_runtime_status_suspended because it
breaks RPM refcounting.
Fixes: 8ebf15e9c869 ("i2c: tegra: Move suspend handling to NOIRQ phase")
Cc: <stable@vger.kernel.org> # v5.4+
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I noticed that sometime I2C clock is kept enabled during suspend-resume.
This happens because runtime PM defers dynamic suspension and thus it may
happen that runtime PM is in active state when system enters into suspend.
In particular I2C controller that is used for CPU's DVFS is often kept ON
during suspend because CPU's voltage scaling happens quite often.
Fixes: 8ebf15e9c869 ("i2c: tegra: Move suspend handling to NOIRQ phase")
Cc: <stable@vger.kernel.org> # v5.4+
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
null_zone_write() only allows writing empty and implicitly opened zones.
Writing to closed and explicitly opened zones must also be allowed and
the zone condition must be transitioned to implicit open if the zone
is not explicitly opened already.
Fixes: da644b2cc1a4 ("null_blk: add zone open, close, and finish support")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch fixes a regression on setting up asynchronous commands to use
external trigger sources when board-specific routing information is
missing.
`ni_find_device_routes()` (called via `ni_assign_device_routes()`) finds
the table of register values for the device family and the set of valid
routes for the specific board. If both are found,
`tables->route_values` is set to point to the table of register values
for the device family and `tables->valid_routes` is set to point to the
list of valid routes for the specific board. If either is not found,
both `tables->route_values` and `tables->valid_routes` are left set at
their initial null values (initialized by `ni_assign_device_routes()`)
and the function returns `-ENODATA`.
Returning an error results in some routing functionality being disabled.
Unfortunately, leaving `table->route_values` set to `NULL` also breaks
the setting up of asynchronous commands that are configured to use
external trigger sources. Calls to `ni_check_trigger_arg()` or
`ni_check_trigger_arg_roffs()` while checking the asynchronous command
set-up would result in a null pointer dereference if
`table->route_values` is `NULL`. The null pointer dereference is fixed
in another patch, but it now results in failure to set up the
asynchronous command. That is a regression from the behavior prior to
commit 347e244884c3 ("staging: comedi: tio: implement global tio/ctr
routing") and commit 56d0b826d39f ("staging: comedi: ni_mio_common:
implement new routing for TRIG_EXT").
Change `ni_find_device_routes()` to set `tables->route_values` and/or
`tables->valid_routes` to valid information even if the other one can
only be set to `NULL` due to missing information. The function will
still return an error in that case. This should result in
`tables->valid_routes` being valid for all currently supported device
families even if the board-specific routing information is missing.
That should be enough to fix the regression on setting up asynchronous
commands to use external triggers for boards with missing routing
information.
Fixes: 347e244884c3 ("staging: comedi: tio: implement global tio/ctr routing")
Fixes: 56d0b826d39f ("staging: comedi: ni_mio_common: implement new routing for TRIG_EXT").
Cc: <stable@vger.kernel.org> # 4.20+
Cc: Spencer E. Olson <olsonse@umich.edu>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200114182532.132058-3-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In `ni_find_route_source()`, `tables->route_values` gets dereferenced.
However it is possible that `tables->route_values` is `NULL`, leading to
a null pointer dereference. `tables->route_values` will be `NULL` if
the call to `ni_assign_device_routes()` during board initialization
returned an error due to missing device family routing information or
missing board-specific routing information. For example, there is
currently no board-specific routing information provided for the
PCIe-6251 board and several other boards, so those are affected by this
bug.
The bug is triggered when `ni_find_route_source()` is called via
`ni_check_trigger_arg()` or `ni_check_trigger_arg_roffs()` when checking
the arguments for setting up asynchronous commands. Fix it by returning
`-EINVAL` if `tables->route_values` is `NULL`.
Even with this fix, setting up asynchronous commands to use external
trigger sources for boards with missing routing information will still
fail gracefully. Since `ni_find_route_source()` only depends on the
device family routing information, it would be better if that was made
available even if the board-specific routing information is missing.
That will be addressed by another patch.
Fixes: 4bb90c87abbe ("staging: comedi: add interface to ni routing table information")
Cc: <stable@vger.kernel.org> # 4.20+
Cc: Spencer E. Olson <olsonse@umich.edu>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200114182532.132058-2-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mlxsw configures Spectrum in such a way that BUM traffic is passed not
through its nominal traffic class TC, but through its MC counterpart TC+8.
However, when collecting statistics, Qdiscs only look at the nominal TC and
ignore the MC TC.
Add two helpers to compute the value for logical TC from the constituents,
one for backlog, the other for tail drops. Use them throughout instead of
going through the xstats pointer directly.
Counters for TX bytes and packets are deduced from packet priority
counters, and therefore already include BUM traffic. wred_drop counter is
irrelevant on MC TCs, because RED is not enabled on them.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.
The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.
Fixes: 075ab8adaf4e ("mlxsw: spectrum: Collect tclass related stats periodically")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 31557f0f9755 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit a72afb6879bb ("mlxsw: Enforce firmware version for
Spectrum-2") I added a required firmware version for Spectrum-2, but
missed the fact that mlxsw_sp2_init() is used by both Spectrum-2 and
Spectrum-3. This means that the same firmware version will be used for
both, which is wrong.
Fix this by creating a new init() callback for Spectrum-3.
Fixes: a72afb6879bb ("mlxsw: Enforce firmware version for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If hub_activate() is called before D+ has stabilized after remote
wakeup, the following situation might occur:
__ ___________________
/ \ /
D+ __/ \__/
Hub _______________________________
| ^ ^ ^
| | | |
Host _____v__|___|___________|______
| | | |
| | | \-- Interrupt Transfer (*3)
| | \-- ClearPortFeature (*2)
| \-- GetPortStatus (*1)
\-- Host detects remote wakeup
- D+ goes high, Host starts running by remote wakeup
- D+ is not stable, goes low
- Host requests GetPortStatus at (*1) and gets the following hub status:
- Current Connect Status bit is 0
- Connect Status Change bit is 1
- D+ stabilizes, goes high
- Host requests ClearPortFeature and thus Connect Status Change bit is
cleared at (*2)
- After waiting 100 ms, Host starts the Interrupt Transfer at (*3)
- Since the Connect Status Change bit is 0, Hub returns NAK.
In this case, port_event() is not called in hub_event() and Host cannot
recognize device. To solve this issue, flag change_bits even if only
Connect Status Change bit is 1 when got in the first GetPortStatus.
This issue occurs rarely because it only if D+ changes during a very
short time between GetPortStatus and ClearPortFeature. However, it is
fatal if it occurs in embedded system.
Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit a7fc89f9d5fcc10a5474cfe555f5a9e5df8b0f1f because
there are some bugs in this commit, and we don't have a simple way to
fix these bugs. So revert this commit to make the thunderx gpio work
on the stable kernel at least. We will switch to GPIOLIB_IRQCHIP
for thunderx gpio by following patches.
Fixes: a7fc89f9d5fc ("gpio: thunderx: Switch to GPIOLIB_IRQCHIP")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-2-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|