| Age | Commit message (Collapse) | Author |
|---|
|
The various chips can be reset using a sequence of SPI transfers with
MOSI = 1. The length of such a sequence varies from chip to chip. Store
that length in struct ad_sigma_delta_info and replace the respective
parameter to ad_sd_reset() with it.
Note the ad7192 used to pass 48 as length but the documentation
specifies 40 as the required length. Assuming the latter is right.
(Using a too long sequence doesn't hurt apart from using a longer spi
transfer than necessary, so this is no relevant fix.)
The motivation for storing this information is that this is useful to
clear a pending R̅D̅Y̅ signal in the next change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/9750db62fce638bf140ff48172c23bff7f785e5b.1733504533.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ad_sigma_delta driver helper uses irq_disable_nosync(). With that
one it is possible that the irq handler still runs after the
irq_disable_nosync() function call returns. Also to properly synchronize
irq disabling in the different threads proper locking is needed and
because it's unclear if the irq handler's irq_disable_nosync() call
comes first or the one in the enabler's error path, all code locations
that disable the irq must check for .irq_dis first to ensure there is
exactly one disable call per enable call.
So add a spinlock to the struct ad_sigma_delta and use it to synchronize
irq enabling and disabling. Also only act in the irq handler if the irq
is still enabled.
Fixes: af3008485ea0 ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/9e6def47e2e773e0e15b7a2c29d22629b53d91b1.1733504533.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Some of the ADCs by Analog signal their irq condition on the MISO line.
So typically that line is connected to an SPI controller and a GPIO. The
GPIO is used as input and the respective interrupt is enabled when the
last SPI transfer is completed.
Depending on the GPIO controller the toggling MISO line might make the
interrupt pending even while it's masked. In that case the irq handler
is called immediately after irq_enable() and so before the device
actually pulls that line low which results in non-sense values being
reported to the upper layers.
The only way to find out if the line was actually pulled low is to read
the GPIO. (There is a flag in AD7124's status register that also signals
if an interrupt was asserted, but reading that register toggles the MISO
line and so might trigger another spurious interrupt.)
Add the possibility to specify an interrupt GPIO in the machine
description in addition to the plain interrupt. This GPIO is used then
to check if the irq line is actually active in the irq handler.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/5be9a4cc4dc600ec384c88db01dd661a21506b9c.1733504533.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Align the irq_line field in struct ad_sigma_delta with the other fields.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241122-iio-adc-ad_signal_delta-fix-align-v1-1-d0a071d2dc83@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Sigma delta ADCs with a sequencer need to disable the previously enabled
channel when reading using ad_sigma_delta_single_conversion(). This was
done manually in drivers for devices with sequencers.
This patch implements handling of single channel disabling after a
single conversion.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240607-ad4111-v7-3-97e3855900a0@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add optional irq_num attribute to ad_sigma_delta_info structure for
selecting the used interrupt line for ADC's conversion completion.
Signed-off-by: Dumitru Ceclan <mitrutzceclan@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240228110622.25114-2-mitrutzceclan@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 1st set of new device support, features and cleanup for 6.9
IIO Backend support
===================
New approach from Nuno Sa to the problem of reuse of drivers with
IIO devices that are actually the combination of a highspeed chip
and an FPGA core handling the data capture and flows. It will hopefully
also apply to some other split designs. The ad9467 and axi-adi drivers
are converted over to this framework.
New device support
==================
adi,admfm2000
- New driver for this dual microwave down converter.
ams,as73211
- Add support for as7331 UV sensor.
richtek,rtq6056
- Add support for related parts RTQ6053 and RTQ6059
st,lsm6dsx
- Add ASM330LHHXG1 accelerometer and gyro support (mainly IDs)
ti,ads1298
- New driver for this medical ADC.
Features
========
tests
- Unit tests for the gain-time-scale helper library.
bosch,bmi088
- I2C support.
bosh,bmi160
- Add 10EC5280 ACPI ID. Used in a number of devices that won't get fixed.
The ID is actually a PCI ID belonging to realtech. No response was received
to earlier attempts to notify them of this.
The manufacturers of some devices have replied to say they will not fix
this incorrect ID. Add the ID and hope it isn't a problem.
bosch,bmi323
- Add BOSC0200 ACPI ID. Note this is a duplicate of one in the bmc150
driver (it appears these parts share a windows driver).
Both drivers perform an ID check that is safe on the other part before
successfully probing.
hid-sensors-als
- Add color temperature and chromaticity support. Note this is a replacement
for the series reverted in 6.8 that correctly handles all the potential
channel combinations.
honeywell,hsc030pa
- Triggered buffer support (after driver cleanup).
honeywell,mprls00025pa
- Improved error handling.
- New DT binding to allow use of part number triplet as provided in data sheet
to specify equivalent of most of the binding more efficiently.
- SPI support.
memsic,mxc4005
- ACPI ID MDA6655 as seen in the Chuwi Minibook X 2023
ti,hdc3020
- Add threshold event support (after some driver cleanup)
veml,vcnl4000
- Switch to high resolution proximity measurement.
Cleanup
=======
Various minor typo fixes and better use of defines etc.
Treewide
- Stop using ACPI_PTR(). The savings in space are small and not worth
the complexity of __maybe_unused of ifdef guards. To avoid use in
new IIO drivers based on copy and paste, clean it out.
- cleanup.h based handling of iio_device_claim_direct_mode()/
iio_device_release_direct_mode() using scope_cond_guard().
In many drivers this is combined with other automated cleanup
to give maximum simplifications.
An initial set of drivers are converted over to this infrastructure.
Tools
- Use rewinddir() instead of seekdir() to return to start of file.
core
- Make iio_bus_type constant.
adi,ad16475
- Use irq_get_trigger_type() instead of opencoding.
adi,ad16480
- Use irq_get_trigger_type() instead of opencoding.
adi,ad-sigma-delta
- Avoid overwriting IRQ flags if provided by firmware.
ams,as73211
- Use IIO_VAL_FRACTIONAL for scales to simplify the code and potentially
improve accuracy.
gts-library
- Use a div64_u64() instead of a loop to do a division.
honeywell,mprls00025pa
- Clean up dt-binding doc.
- Drop defaults when DT binding not providing values. Very unlikely
these were useful given they were wrong for vast majority of supported
devices.
- Whitespace cleanup
miramems,da280
- Use i2c_get_match_data() to replace hand rolled ACPI matching code.
semtech,sx9324
- Avoid unnecessary copying of property strings.
st,lsm6dsx
- Improve docs, particularly wrt to making addition of new device
support less noisy.
st,lsm9ds0
- Use dev_err_probe() in all probe() error handling.
- Improved header includes.
- Tidy up termination of ID tables.
ti,ads1014
- Correct upper bound on PGA (wrong value had no actual impact)
ti,afe4403/4404
- devm_ useage to simplify error handling in probe() and allow() remove to
be dropped.
voltage-divider
- Add dt-binding for io-channel-cells to allow such a device to be both
an IIO consumer and IIO producer at the same time.
* tag 'iio-for-6.9a' of http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (106 commits)
iio: imu: bmi323: Add ACPI Match Table
iio: accel: bmc150: Document duplicate ACPI entries with bmi323 driver
iio: adc: ti-ads1298: Add driver
dt-bindings: iio: adc: ti-ads1298: Add bindings
iio: pressure: hsc030pa add triggered buffer
iio: pressure: hsc030pa add mandatory delay
iio: pressure: hsc030pa: update datasheet URLs
iio: pressure: hsc030pa: include cleanup
iio: pressure: hsc030pa: use signed type to hold div_64() result
dt-bindings: iio: pressure: honeywell,hsc030pa.yaml add spi props
iio: st_sensors: lsm9ds0: Use common style for terminator in ID tables
iio: st_sensors: lsm9ds0: Don't use "proxy" headers
iio: st_sensors: lsm9ds0: Use dev_err_probe() everywhere
iio: adc: adi-axi-adc: move to backend framework
iio: adc: ad9467: convert to backend framework
iio: add the IIO backend framework
iio: buffer-dmaengine: export buffer alloc and free functions
of: property: add device link support for io-backends
dt-bindings: adc: axi-adc: update bindings for backend framework
dt-bindings: adc: ad9467: add new io-backend property
...
|
|
Move to the IIO backend framework. Devices supported by adi-axi-adc now
register themselves as backend devices.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240210-iio-backend-v11-7-f5242a5fb42a@analog.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Aligning the buffer to the L1 cache is not sufficient in some platforms
as they might have larger cacheline sizes for caches after L1 and thus,
we can't guarantee DMA safety.
That was the whole reason to introduce IIO_DMA_MINALIGN in [1]. Do the same
for the sigma_delta ADCs.
[1]: https://lore.kernel.org/linux-iio/20220508175712.647246-2-jic23@kernel.org/
Fixes: 0fb6ee8d0b5e ("iio: ad_sigma_delta: Don't put SPI transfer buffer on the stack")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240117-dev_sigma_delta_no_irq_flags-v1-1-db39261592cf@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
When reading in_voltage_scale we can get something like:
root@analog:/sys/bus/iio/devices/iio:device2# cat in_voltage_scale
0.038146
However, when reading the available options:
root@analog:/sys/bus/iio/devices/iio:device2# cat
in_voltage_scale_available
2000.000000 2100.000006 2200.000007 2300.000008 2400.000009 2500.000010
which does not make sense. Moreover, when trying to set a new scale we
get an error because there's no call to __ad9467_get_scale() to give us
values as given when reading in_voltage_scale. Fix it by computing the
available scales during probe and properly pass the list when
.read_available() is called.
While at it, change to use .read_available() from iio_info. Also note
that to properly fix this, adi-axi-adc.c has to be changed accordingly.
Fixes: ad6797120238 ("iio: adc: ad9467: add support AD9467 ADC")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-4-a4a33bc4d70e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
|
|
Add reverse scaling function for PMIC5 Gen2 ADC_TM, to convert
temperature to raw ADC code, for setting thresholds for
thermistor channels.
Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/1648991869-20899-3-git-send-email-quic_jprakash@quicinc.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Some sigma-delta chips support sampling of multiple
channels in continuous mode.
When the operating with more than one channel enabled,
the channel sequencer cycles through the enabled channels
in sequential order, from first channel to the last one.
If a channel is disabled, it is skipped by the sequencer.
If more than one channel is used in continuous mode,
instruct the device to append the status to the SPI transfer
(1 extra byte) every time we receive a sample.
All sigma-delta chips possessing a sampling sequencer have
this ability. Inside the status register there will be
the number of the converted channel. In this way, even
if the CPU won't keep up with the sampling rate, it won't
send to userspace wrong channel samples.
When multiple channels are enabled in continuous mode,
the device needs to perform a measurement on all slots
before we can push to userspace the sample.
If, during sequencing and data reading, a channel measurement
is lost, a desync occurred. In this case, ad_sigma_delta drops
the incomplete sample and waits for the device to send the
measurement on the first active slot.
Co-developed-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220322105029.86389-5-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Instead of custom data type re-use generic struct u32_fract.
No changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220126135353.24007-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since all AD Sigma-Delta drivers now use the
devm_ad_sd_setup_buffer_and_trigger() function, we can remove the old
ad_sd_{setup,cleanup}_buffer_and_trigger() functions.
This way we can discourage new drivers that use the ad_sigma_delta
lib-driver to use these (older functions).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-13-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This is a version of ad_sd_setup_buffer_and_trigger() with all underlying
functions (that are used) being replaced with their device-managed
variants.
One thing to take care here is with {devm_}iio_trigger_alloc(), where both
functions take a parent-device object as the first parameter.
To make sure nothing quirky is happening, the devm_ad_sd_probe_trigger()
function is checking that the provided 'dev' reference is the same as the
one stored on the 'struct ad_sigma_delta' driver data.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The channels are of type iio_chan_spec, not axi_adc_chan_spec. They were in
some earlier version, but forgot to rename in the doc-string.
Fixes: ef04070692a21 ("iio: adc: adi-axi-adc: add support for AXI ADC IP core")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210219090134.48057-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for Thermal Monitoring part of PMIC5. This part is closely
coupled with ADC, using it's channels directly. ADC-TM support
generating interrupts on ADC value crossing low or high voltage bounds,
which is used to support thermal trip points.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205000118.493610-3-dmitry.baryshkov@linaro.org
|
|
qcom_vadc7_scale_hw_calib_die_temp() uses a table format different from
the rest of volt/temp conversion functions in this file. Also the
conversion functions results in non-monothonic values conversion, which
seems wrong.
Rewrite qcom_vadc7_scale_hw_calib_die_temp() to use
qcom_vadc_map_voltage_temp() directly, like the rest of conversion
functions do.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-10-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
struct vadc_map_pt is not used outside of qcom-vadc-common.c, so move it
there from the global header file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-9-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
qcom-vadc-common module will be used by ADC thermal monitoring driver,
so move it to global include dir.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-6-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use a heap allocated memory for the SPI transfer buffer. Using stack memory
can corrupt stack memory when using DMA on some systems.
This change moves the buffer from the stack of the trigger handler call to
the heap of the buffer of the state struct. The size increases takes into
account the alignment for the timestamp, which is 8 bytes.
The 'data' buffer is split into 'tx_buf' and 'rx_buf', to make a clearer
separation of which part of the buffer should be used for TX & RX.
Fixes: af3008485ea03 ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201124123807.19717-1-alexandru.ardelean@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change adds support for the Analog Devices Generic AXI ADC IP core.
The IP core is used for interfacing with analog-to-digital (ADC) converters
that require either a high-speed serial interface (JESD204B/C) or a source
synchronous parallel interface (LVDS/CMOS).
Usually, some other interface type (i.e SPI) is used as a control interface
for the actual ADC, while the IP core (controlled via this driver), will
interface to the data-lines of the ADC and handle the streaming of data
into memory via DMA.
Because of this, the AXI ADC driver needs the other SPI-ADC driver to
register with it. The SPI-ADC needs to be register via the SPI framework,
while the AXI ADC registers as a platform driver. The two cannot be ordered
in a hierarchy as both drivers have their own registers, and trying to
organize this [in a hierarchy becomes] problematic when trying to map
memory/registers.
There are some modes where the AXI ADC can operate as standalone ADC, but
those will be implemented at a later point in time.
DocLink: https://wiki.analog.com/resources/fpga/docs/axi_adc_ip
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Now that all channel SigmaDelta IIO channel macros have been localized,
remove the generic ones.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Before this patch the ad_sigma_delta implementation hardcoded
the irq trigger type to low, assuming that all Sigma-Delta ADCs
have the same interrupt-type.
This patch allows all drivers using the ad_sigma_delta layer to set the
irq trigger type to the one specified in the datasheet.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch exports the ad_sd_calibrate function in order to be able to
call it from outside ad_sigma_delta.
There are cases where the option to calibrate one channel at a time is
necessary (ex. system calibration for zero scale and full scale).
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Some newer devices from the Sigma-Delta ADC family do have their data
register at a different address than the current default address. Add a
parameter to the ad_sigma_delta_info struct which allows to override the
default address.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix the following sparse warnings:
CHECK drivers/iio/adc/stm32-dfsdm-adc.c
symbol 'stm32_dfsdm_get_buff_cb' was not declared. Should it be static?
symbol 'stm32_dfsdm_release_buff_cb' was not declared. Should it be static?
BTW, move interrupt.h to sort headers alphabetically.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The `ad7780` driver does not implement setting/getting the sampling
frequency.
For the ad7780/ad7781 devices, the control is done via an external pin,
and the ad7170/ad7171 devices have a fixed sampling rate (so, no control).
For these devices, and similar other that may be added later on,
a AD_SD_CHANNEL_NO_SAMPLE_FREQ() macro has been added, which doesn't set
the IIO_CHAN_INFO_SAMP_FREQ flag.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This code offers a way to handle PDM audio microphones in
ASOC framework. Audio driver should use consumer API.
A specific management is implemented for DMA, with a
callback, to allows to handle audio buffers efficiently.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since most of the SD ADCs have the option of reseting the serial
interface by sending a number of SCLKs with CS = 0 and DIN = 1,
a dedicated function that can do this is usefull.
Needed for the patch: iio: ad7793: Fix the serial interface reset
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This driver predates the availability of IIO_CHAN_INFO_SAMP_FREQ
attribute wherein usage has some advantages like it can be accessed by
in-kernel consumers as well as reduces the code size.
Therefore, use IIO_CHAN_INFO_SAMP_FREQ to implement the
sampling_frequency attribute instead of using IIO_DEV_ATTR_SAMP_FREQ()
macro.
Move code from the functions associated with IIO_DEV_ATTR_SAMP_FREQ()
into respective read and write hooks with the mask set to
IIO_CHAN_INFO_SAMP_FREQ.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
Most devices from the Analog Devices Sigma Delta family use a similar scheme for
communication with the device. This includes register access, as well as trigger
handling. But each device sub-family has different features and different
register layouts (some even have no registers at all) and thus it is impractical
to try to support all of the devices by the same driver. This patch adds a
common base library for Sigma Delta converter devices. It will be used by
individual drivers.
This code is mostly based on the three existing Sigma Delta drivers the AD7192,
AD7780 and AD7793, but has been improved for more robustness and flexibility.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
