| Age | Commit message (Collapse) | Author |
|---|
|
Fix kernel-doc warnings in regulator header files:
Warning(..//include/linux/regulator/machine.h:140): No description found for parameter 'ramp_disable'
Warning(..//include/linux/regulator/driver.h:279): No description found for parameter 'linear_ranges'
Warning(..//include/linux/regulator/driver.h:279): No description found for parameter 'n_linear_ranges'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'regulator/topic/getreg', 'regulator/topic/gpio' and 'regulator/topic/lp872x' into regulator-next
|
|
'regulator/topic/ab8500', 'regulator/topic/act8865', 'regulator/topic/as3722' and 'regulator/topic/bcm590xx' into regulator-next
|
|
Add device id and definition of registers and regulators to support
the act8846 PMU.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch prepares support for other devices in the act88xx family of
PMUs manufactured by Active-Semi.
http://www.active-semi.com/products/power-management-units/act88xx/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
So we don't get multiple definitions.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add helper functions that allow regulator consumers to obtain low-level
details about the regulator hardware, like the voltage selector register
address and such. These details can be useful when configuring hardware
or firmware that want to do low-level access to regulators, with no
involvement from the kernel.
The use-case for Tegra is a voltage-controlled oscillator clocksource
which has control logic to change the supply voltage via I2C to achieve
a desired output clock rate.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This is the driver for the Dialog DA9211 Multi-phase 12A DC-DC Buck
Converter regulator. It communicates via an I2C bus to the device.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
CONFIG_REGULATOR_AB8500_DEBUG is always not defined.
ab8500_regulator_debug_init() is not called at all now,
ab8500_regulator_debug_exit() simply return 0, thus remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
When CONFIG_REGULATOR is not set, we cannot call
regulator_can_change_voltage() from a device driver, which results
in a build error like
video/fbdev/omap2/dss/hdmi5.c: In function 'hdmi_init_regulator':
video/fbdev/omap2/dss/hdmi5.c:149:2: error: implicit declaration of function 'regulator_can_change_voltage' [-Werror=implicit-function-declaration]
even for drivers that don't require the regulator API normally.
Such a use was recently added in the omap2+ hdmi driver.
This avoids the problem by adding a static inline function
stub in the API header, as we have for most of the other
regulator functions as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'regulator/topic/stub', 'regulator/topic/tps65090', 'regulator/topic/tps65217' and 'regulator/topic/tps65218' into regulator-next
|
|
|
|
We already have dummy implementation for most of the regulators APIs for
!CONFIG_REGULATOR case and were missing it for regulator_set_voltage_time().
Found this issue while compiling cpufreq-cpu0 driver without regulators support
in kernel.
drivers/cpufreq/cpufreq-cpu0.c: In function ‘cpu0_cpufreq_probe’:
drivers/cpufreq/cpufreq-cpu0.c:186:3: error: implicit declaration of function ‘regulator_set_voltage_time’ [-Werror=implicit-function-declaration]
Fix this by adding dummy definition for regulator_set_voltage_time().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Toughen-up checks for read-only regulator names.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Drivers that call regulator_get_optional are tolerant to the absence of
that regulator. By modifying the value returned from the stub function
to match that seen when a regulator isn't present, callers can wrap the
regulator logic with an IS_ERR based conditional even if they happen to
call regulator_is_supported_voltage. This improves efficiency as well
as eliminates the possibility for a very subtle bug.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'regulator/topic/max8997', 'regulator/topic/max8998', 'regulator/topic/mc13xxx', 'regulator/topic/pfuze100', 'regulator/topic/rc5t583' and 'regulator/topic/s2mps11' into regulator-next
|
|
This patch extends the regulator helpers to account for device that use
multiple bits for control when using regmap enable/disable/bypass ops.
The actual regulator helpers wrongly assume that the regulator control
is always performed using single bits, using in the regulator_desc
struct only two parameters *_reg and *_mask defining register and mask
for control.
This patch extends this struct and introduces the helpers to take into
account devices where control is performed using multiple bits and
specific multi-bit values are used for enabling/disabling/bypassing the
regulator.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
support pfuze200 chip which remove SW1C and SW4 based on pfuze100.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
These patches add the ability to create an alternative device on which
a lookup for a certain supply should be conducted.
A common use-case for this would be devices that are logically
represented as a collection of drivers within Linux but are are
presented as a single device from device tree. It this case it is
necessary for each sub device to locate their supply data on the main
device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add REGULATOR_LINEAR_RANGE macro and convert regulator drivers to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
linear ranges means each range has linear voltage settings.
So we can calculate max_uV for each linear range in regulator core rather than
set the max_uV field in drivers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The turn-on time of the regulator depends on the regulator device's
electrical characteristics. Sometimes regulator turn-on time also
depends on the capacitive load on the given platform and it can be
more than the datasheet value.
The driver provides the enable-time as per datasheet.
Add support for configure the enable ramp time through regulator
constraints so that regulator core can take this value for enable
time for that regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Fix fatal kernel-doc error in <linux/regulator/driver.h>:
Error(include/linux/regulator/driver.h:52): cannot understand prototype: 'struct regulator_linear_range '
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[Rewrote first line -- broonie]
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
No boards have used this functionality and the new default of providing
dummy regulators by default provides a better solution to the problem it
was trying to solve.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Many regulator drivers have a remove function that consists solely of
calling regulator_unregister() so provide a devm_regulator_register()
in order to allow this repeated code to be removed and help eliminate
error handling code.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
If given rail has the single voltage (n_voltages = 1) then provide the
rail voltage through regulator descriptor so that core can use this
value for finding voltage.
This will avoid the implementation of the callback for get_voltage() or
list_voltage() callback on regulator driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Add a resource managed regulator_get_exclusive()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add define for __FAN53555_H__ to prevent multiple include of the header file.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds devicetree bindings for max8660, along with some
documentation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
While the majority of supplies on devices are mandatory and can't be
physically omitted for electrical reasons some devices do have optional
supplies and need to know if they are missing, MMC being the most common
of these.
Currently the core accurately reports all errors when regulators are
requested since it does not know if the supply is one that must be provided
even if by a regulator software does not know about or if it is one that
may genuinely be disconnected. In order to allow this behaviour to be
changed and stub regulators to be provided in the former case add a new
regulator request function regulator_get_optional() which provides a hint
to the core that the regulator may genuinely not be connected.
Currently the implementation is identical to the current behaviour, future
patches will add support in the core for returning stub regulators in the
case where normal regulator_get() fails and the board has requested it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add pfuze100 regulator driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Some hardwares support disabling ramp delay, so adding ramp_disable flag to
constraints. It will be used to figure out whether ramp_delay in constraints
is explicitly set to zero or its unintialized (zero by default).
And we don't need to call set_voltage_time_sel() for regulators for whom ramp
delay is disabled in constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Many regulators have several linear ranges of selector with different
step sizes, for example offering better resolution at lower voltages.
Provide regulator_{map,list}_voltage_linear_range() allowing these
regulators to use generic code. To do so a table of regulator_linear_range
structs needs to be pointed to from the descriptor.
This was inspired by similar code included in a driver submission from
Chao Xie and Yi Zhang at Marvell.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The expected semantic for something expressed as a tolerance is that it
should deliver the specified value with some deviation allowed but this
is not what set_voltage_tol() currently does. Instead it just passes
the maximum possible range to set_voltage() which will typically result
in a voltage aimed at lower than the target voltage.
Instead first try to set a voltage between the target voltage and the
upper limit, then fall back on the full range. This will be much more
robust against physical variation in systems and makes the API behave
more like users would expect.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
Some platforms don't support the AB8500 external regulators, so instead
of having a list of is_<platform>() calls prior to calling
ab8500_ext_regulator_init() from ab8500_regulator_probe(), we can only
register as a platform device on platforms which require them. It means
we also have more control over them when booting with Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonielinaro.org>
|
