| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
A few more Qualcomm driver updates for v6.13
Make the Adreno driver invoke the SMMU aperture setup firmware function,
which is required to allow the GPU to manage per-process page tables in
some firmware versions - as an example Rb3Gen2 has no GPU without this.
Add X1E Devkit to the list of devices that has functional EFI variable
access through the uefisecapp.
Flip the "manual slice configuration quirk" in the Qualcomm LLCC driver,
as this only applies to a single platform, and introduce support for
QCS8300, QCS615, SAR2130P, and SAR1130P.
Lastly, add IPQ5424 and IPQ5404 to the Qualcomm socinfo driver.
* tag 'qcom-drivers-for-6.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
soc: qcom: llcc: Add configuration data for QCS615
dt-bindings: cache: qcom,llcc: Document the QCS615 LLCC
soc: qcom: llcc: add support for SAR2130P and SAR1130P
soc: qcom: llcc: use deciman integers for bit shift values
dt-bindings: cache: qcom,llcc: document SAR2130P and SAR1130P
Link: https://lore.kernel.org/r/20241113032425.356306-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm driver fixes for v6.12
The Qualcomm EDAC driver's configuration of interrupts is made optional,
to avoid violating security constriants on X Elite platform .
The SCM drivers' detection mechanism for the presence of SHM bridge in QTEE,
is corrected to handle the case where firmware successfully returns that
the interface isn't supported.
The GLINK driver and the PMIC GLINK interface is updated to handle
buffer allocation issues during initialization of the communication
channel.
Allocation error handling in the socinfo dirver is corrected, and then
the fix is corrected.
* tag 'qcom-drivers-fixes-for-6.12' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: pmic_glink: Handle GLINK intent allocation rejections
rpmsg: glink: Handle rejected intent request better
soc: qcom: socinfo: fix revision check in qcom_socinfo_probe()
firmware: qcom: scm: Return -EOPNOTSUPP for unsupported SHM bridge enabling
EDAC/qcom: Make irq configuration optional
firmware: qcom: scm: fix a NULL-pointer dereference
firmware: qcom: scm: suppress download mode error
soc: qcom: Add check devm_kasprintf() returned value
MAINTAINERS: Qualcomm SoC: Match reserved-memory bindings
Link: https://lore.kernel.org/r/20241101161455.746290-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Implement necessary support for the LLCC control on the SAR1130P and
SAR2130P platforms. These two platforms use different ATTR1_MAX_CAP
shift and also require manual override for num_banks.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241026-sar2130p-llcc-v3-3-2a58fa1b4d12@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Cancelling an rx command is signalled using bit 14 of the rx DMA status
register and not bit 11.
This bit is currently unused, but this error becomes apparent, for
example, when tracing the status register when closing the port.
Fixes: eddac5af0654 ("soc: qcom: Add GENI based QUP Wrapper driver")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-7-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On most modern qualcomm SoCs, the configuration necessary to enable the
Tag/Data RAM related irqs being propagated to the SoC irq controller is
already done in firmware (in DSF or 'DDR System Firmware')
On some like the x1e80100, these registers aren't even accesible to the
kernel causing a crash when edac device is probed.
Hence, make the irq configuration optional in the driver and mark x1e80100
as the SoC on which this should be avoided.
Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Reported-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240903101510.3452734-1-quic_rjendra@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
|
|
For UART devices the M_GP_LENGTH is the TX word count. For other
devices this is the transaction word count.
For UART devices the S_GP_LENGTH is the RX word count.
The IRQ_EN set/clear registers allow you to set or clear bits in the
IRQ_EN register without needing a read-modify-write.
Acked-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240610152420.v4.1.Ife7ced506aef1be3158712aa3ff34a006b973559@changeid
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As pointed out by Stephen Boyd it is possible that during initialization
of the pmic_glink child drivers, the protection-domain notifiers fires,
and the associated work is scheduled, before the client registration
returns and as a result the local "client" pointer has been initialized.
The outcome of this is a NULL pointer dereference as the "client"
pointer is blindly dereferenced.
Timeline provided by Stephen:
CPU0 CPU1
---- ----
ucsi->client = NULL;
devm_pmic_glink_register_client()
client->pdr_notify(client->priv, pg->client_state)
pmic_glink_ucsi_pdr_notify()
schedule_work(&ucsi->register_work)
<schedule away>
pmic_glink_ucsi_register()
ucsi_register()
pmic_glink_ucsi_read_version()
pmic_glink_ucsi_read()
pmic_glink_ucsi_read()
pmic_glink_send(ucsi->client)
<client is NULL BAD>
ucsi->client = client // Too late!
This code is identical across the altmode, battery manager and usci
child drivers.
Resolve this by splitting the allocation of the "client" object and the
registration thereof into two operations.
This only happens if the protection domain registry is populated at the
time of registration, which by the introduction of commit '1ebcde047c54
("soc: qcom: add pd-mapper implementation")' became much more likely.
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/all/CAMi1Hd2_a7TjA7J9ShrAbNOd_CoZ3D87twmO5t+nZxC9sX18tA@mail.gmail.com/
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/all/ZqiyLvP0gkBnuekL@hovoldconsulting.com/
Reported-by: Stephen Boyd <swboyd@chromium.org>
Closes: https://lore.kernel.org/all/CAE-0n52JgfCBWiFQyQWPji8cq_rCsviBpW-m72YitgNfdaEhQg@mail.gmail.com/
Fixes: 58ef4ece1e41 ("soc: qcom: pmic_glink: Introduce base PMIC GLINK driver")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240820-pmic-glink-v6-11-races-v3-1-eec53c750a04@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
- The maximum amount of DDR memory used by the Mediatek MT8188/MT8195
SCP is increased to handle new use cases. Handling of optional L1TCM
memory is made actually optional.
- An optimization is introduced to only clear the unused portion of IPI
shared buffers, rather than the entire buffer before writing the
message.
- Detection for IPC-only mode in the TI K3 DSP remoteproc driver is
corrected. The loglevel of a debug print in the same is lowered from
error.
- Support for attaching to an running remote processor is added to the
Xilinx R5F.
- An in-kernel implementation of the Qualcomm "protected domain mapper"
(aka service registry) service is introduced, to remove the
dependency on a userspace implementation to detect when the battery
monitor and USB Type-C port manager becomes available. This is then
integrated with the Qualcomm remoteproc driver.
- The Qualcomm PAS remoteproc driver gains support for attempting to
bust hwspinlocks held by the remote processor when it
crashed/stopped.
- The TI OMAP remoteproc driver is transitioned to use devres helpers
for various forms of allocations.
- Parsing of memory-regions in the i.MX remoteproc driver is improved
to avoid a NULL pointer dereference if the phandle reference is
empty. of_node reference counting is corrected in the same.
* tag 'rproc-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
remoteproc: mediatek: Increase MT8188/MT8195 SCP core0 DRAM size
remoteproc: k3-dsp: Fix log levels where appropriate
remoteproc: xlnx: Add attach detach support
remoteproc: qcom: select AUXILIARY_BUS
remoteproc: k3-r5: Fix IPC-only mode detection
remoteproc: mediatek: Don't attempt to remap l1tcm memory if missing
remoteproc: qcom: enable in-kernel PD mapper
dt-bindings: remoteproc: imx_rproc: Add minItems for power-domain
remoteproc: imx_rproc: Fix refcount mistake in imx_rproc_addr_init
remoteproc: omap: Use devm_rproc_add() helper
remoteproc: omap: Use devm action to release reserved memory
remoteproc: omap: Use devm_rproc_alloc() helper
remoteproc: imx_rproc: Skip over memory region when node value is NULL
dt-bindings: remoteproc: k3-dsp: Correct optional sram properties for AM62A SoCs
remoteproc: qcom_q6v5_pas: Add hwspinlock bust on stop
soc: qcom: smem: Add qcom_smem_bust_hwspin_lock_by_host()
remoteproc: mediatek: Zero out only remaining bytes of IPI buffer
|
|
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drivers-for-6.11
Merge SMEM and SCM patches related to GPU features through a topic
branch to make it possible to share these with the msm-next DRM tree.
|
|
Recent (SM8550+ ish) Qualcomm SoCs have a new mechanism for precisely
identifying the specific SKU and the precise speed bin (in the general
meaning of this word, anyway): a pair of values called Product Code
and Feature Code.
Based on this information, we can deduce the available frequencies for
things such as Adreno. In the case of Adreno specifically, Pcode is
useless for non-prototype SoCs.
Introduce a getter for the feature code and export it.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240605-topic-smem_speedbin-v2-2-8989d7e3d176@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
In preparation for parsing the chip "feature code" (FC) and "product
code" (PC) (essentially the parameters that let us conclusively
characterize the sillicon we're running on, including various speed
bins), move the socinfo version defines to the public header.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240605-topic-smem_speedbin-v2-1-8989d7e3d176@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Until SM8450, there was only one broadcast region (Broadcast_OR)
used to broadcast write and check for status bit 0.
>From SM8450 onwards another broadcast region (Broadcast_AND) has been
added which checks for status bit 1. This hasn't been updated and
Broadcast_OR region was wrongly being used to check for status bit 1 all
along.
Hence define new regmap structure for Broadcast_AND region and initialize
this regmap when HW block version is greater than 4.1, otherwise
initialize as a NULL pointer for backwards compatibility.
Switch from broadcast_OR to broadcast_AND region (when defined in DT)
for checking status bit 1 as Broadcast_OR region checks only for bit 0.
Signed-off-by: Unnathi Chalicheemala <quic_uchalich@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/9cf19928a67eaa577ae0f02de5bf86276be34ea2.1717014052.git.quic_uchalich@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add qcom_smem_bust_hwspin_lock_by_host to enable remoteproc to bust the
hwspin_lock owned by smem. In the event the remoteproc crashes
unexpectedly, the remoteproc driver can invoke this API to try and bust
the hwspin_lock and release the lock if still held by the remoteproc
device.
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240529-hwspinlock-bust-v3-3-c8b924ffa5a2@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
dt-bindings: serial: stm32: add power-domains property
serial: 8250_dw: Replace ACPI device check by a quirk
serial: Lock console when calling into driver before registration
serial: 8250_uniphier: Switch to use uart_read_port_properties()
serial: 8250_tegra: Switch to use uart_read_port_properties()
serial: 8250_pxa: Switch to use uart_read_port_properties()
serial: 8250_omap: Switch to use uart_read_port_properties()
serial: 8250_of: Switch to use uart_read_port_properties()
serial: 8250_lpc18xx: Switch to use uart_read_port_properties()
serial: 8250_ingenic: Switch to use uart_read_port_properties()
serial: 8250_dw: Switch to use uart_read_port_properties()
serial: 8250_bcm7271: Switch to use uart_read_port_properties()
serial: 8250_bcm2835aux: Switch to use uart_read_port_properties()
serial: 8250_aspeed_vuart: Switch to use uart_read_port_properties()
serial: port: Introduce a common helper to read properties
serial: core: Add UPIO_UNKNOWN constant for unknown port type
serial: core: Move struct uart_port::quirks closer to possible values
serial: sh-sci: Call sci_serial_{in,out}() directly
serial: core: only stop transmit when HW fifo is empty
serial: pch: Use uart_prepare_sysrq_char().
...
|
|
Since commit d492cc2573a0 ("driver core: device.h: make struct
bus_type a const *"), the driver core can properly handle constant
struct bus_type, move the aprbus variable to be a constant
structure as well, placing it into read-only memory which can not be
modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: "Ricardo B. Marliere" <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240213-bus_cleanup-apr-v1-1-50c824eec06d@marliere.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the Qualcomm PBS (Programmable Boot Sequencer) driver. The QCOM PBS
driver supports configuring software PBS trigger events through PBS RAM
on Qualcomm Technologies, Inc (QTI) PMICs.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20240201204421.16992-6-quic_amelende@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
According to the docs I have, bit 21 of the status register is
asserted when the FIFO is _not_ empty. Add the definition.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240112150307.1.I7dc0993c1e758a1efedd651e7e1670deb1b430fb@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update macro name for LLCC_DRE to LLCC_ECC as per the latest specification.
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230830105654.28057-6-quic_kbajaj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"This pull request is full of clk driver changes. In fact, there aren't
any changes to the clk framework this time around. That's probably
because everyone was on vacation (yours truly included). We did lose a
couple clk drivers this time around because nobody was using those
devices. That skews the diffstat a bit, but either way, nothing looks
out of the ordinary here. The usual suspects are chugging along adding
support for more SoCs and fixing bugs.
If I had to choose, I'd say the theme for the past few months has been
"polish". There's quite a few patches that migrate to
devm_platform_ioremap_resource() in here. And there's more than a
handful of patches that move the NR_CLKS define from the DT binding
header to the driver. There's even patches that migrate drivers to use
clk_parent_data and clk_hw to describe clk tree topology. It seems
that the spring (summer?) cleaning bug got some folks, or the
semiconductor shortage finally hit the software side.
New Drivers:
- StarFive JH7110 SoC clock drivers
- Qualcomm IPQ5018 Global Clock Controller driver
- Versa3 clk generator to support 48KHz playback/record with audio
codec on RZ/G2L SMARC EVK
Removed Drivers:
- Remove non-OF mmp clk drivers
- Remove OXNAS clk driver
Updates:
- Add __counted_by to struct clk_hw_onecell_data and struct
spmi_pmic_div_clk_cc
- Move defines for numbers of clks (NR_CLKS) from DT headers to
drivers
- Introduce kstrdup_and_replace() and use it
- Add PLL rates for Rockchip rk3568
- Add the display clock tree for Rockchip rv1126
- Add Audio Clock Generator (ADG) clocks on Renesas R-Car Gen3 and
RZ/G2 SoCs
- Convert sun9i-mmc clock to use
devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c
- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for Allwinner NKM clocks, i.e.
consider alternative parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for Allwinner A64 pll-mipi
- Support finding closest (as opposed to closest but not higher)
clock rate for NM, NKM, mux and div type clocks, as use it for
Allwinner A64 pll-video0
- Prefer current parent rate if able to generate ideal clock rate for
Allwinner NKM clocks
- Clean up Qualcomm SMD RPM driver, with interconnect bus clocks
moved out to the interconnect drivers
- Fix various PM runtime bugs across many Qualcomm clk drivers
- Migrate Qualcomm MDM9615 is to parent_hw and parent_data
- Add network related resets on Qualcomm IPQ4019
- Add a couple missing USB related clocks to Qualcomm IPQ9574
- Add missing gpll0_sleep_clk_src to Qualcomm MSM8917 global clock
controller
- In the Qualcomm QDU1000 global clock controller, GDSCs, clkrefs,
and GPLL1 are added, while PCIe pipe clock, SDCC rcg ops are
corrected
- Add missing GDSCs to and correct GDSCs for the SC8280XP global
clock controller driver
- Support retention for the Qualcomm SC8280XP display clock
controller GDSCs.
- Qualcommm's SDCC apps_clk_src is marked with CLK_OPS_PARENT_ENABLE
to fix issues with missing parent clocks across sc7180, sm7150,
sm6350 and sm8250, while sm8450 is corrected to use floor ops
- Correct Qualcomm SM6350 GPU clock controller's clock supplies
- Drop unwanted clocks from the Qualcomm IPQ5332 GCC driver
- Add missing OXILICX GDSC to Qualcomm MSM8226 GCC
- Change the delay in the Qualcomm reset controller to fsleep() for
correctness
- Extend the Qualcomm SM83550 Video clock controller to support
SC8280XP
- Add graphics clock support on Renesas RZ/G2M, RZ/G2N, RZ/G2E, and
R-Car H3, M3-W, and M3-N SoCs
- Add Clocked Serial Interface (CSI) clocks on Renesas RZ/V2M
- Add PWM (MTU3) clock and reset on Renesas RZ/G2UL and RZ/Five
- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() implementation for i.MX GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource()
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init()
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for i.MX PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from i.MX PLL14xx rate table to
allow glitch free switching"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (207 commits)
clk: qcom: Fix SM_GPUCC_8450 dependencies
clk: lmk04832: Support using PLL1_LD as SPI readback pin
clk: lmk04832: Don't disable vco clock on probe fail
clk: lmk04832: Set missing parent_names for output clocks
clk: mvebu: Convert to devm_platform_ioremap_resource()
clk: nuvoton: Convert to devm_platform_ioremap_resource()
clk: socfpga: agilex: Convert to devm_platform_ioremap_resource()
clk: ti: Use devm_platform_get_and_ioremap_resource()
clk: mediatek: Convert to devm_platform_ioremap_resource()
clk: hsdk-pll: Convert to devm_platform_ioremap_resource()
clk: gemini: Convert to devm_platform_ioremap_resource()
clk: fsl-sai: Convert to devm_platform_ioremap_resource()
clk: bm1880: Convert to devm_platform_ioremap_resource()
clk: axm5516: Convert to devm_platform_ioremap_resource()
clk: actions: Convert to devm_platform_ioremap_resource()
clk: cdce925: Remove redundant of_match_ptr()
clk: pxa910: Move number of clocks to driver source
clk: pxa1928: Move number of clocks to driver source
clk: pxa168: Move number of clocks to driver source
clk: mmp2: Move number of clocks to driver source
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main change this time was the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other
firmware drivers.
On the soc driver side, the updates are mostly cleanups across a
number of Arm platforms. On driver for loongarch adds power management
for DT based systems, another driver is for HiSilicon's Arm server
chips with their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform"
* tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (136 commits)
bus: fsl-mc: Use common ranges functions
soc: kunpeng_hccs: fix some sparse warnings about incorrect type
soc: loongson2_pm: add power management support
soc: dt-bindings: add loongson-2 pm
soc: rockchip: grf: Fix SDMMC not working on RK3588 with bus-width > 1
genpd: rockchip: Add PD_VO entry for rv1126
bus: ti-sysc: Fix cast to enum warning
soc: kunpeng_hccs: add MAILBOX dependency
MAINTAINERS: remove OXNAS entry
dt-bindings: interrupt-controller: arm,versatile-fpga-irq: mark oxnas compatible as deprecated
irqchip: irq-versatile-fpga: remove obsolete oxnas compatible
soc: qcom: aoss: Tidy up qmp_send() callers
soc: qcom: aoss: Format string in qmp_send()
soc: qcom: aoss: Move length requirements from caller
soc: kunpeng_hccs: fix size_t format string
soc: ti: k3-socinfo.c: Add JTAG ID for AM62PX
dt-bindings: firmware: qcom: scm: Updating VMID list
firmware: imx: scu-irq: support identifying SCU wakeup source from sysfs
firmware: imx: scu-irq: enlarge the IMX_SC_IRQ_NUM_GROUP
firmware: imx: scu-irq: add imx_scu_irq_get_status
...
|
|
The majority of callers to qmp_send() composes the message dynamically
using some form of sprintf(), resulting in unnecessary complication and
stack usage.
By changing the interface of qmp_send() to take a format string and
arguments, the duplicated composition of the commands can be moved to a
single location.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230811205839.727373-4-quic_bjorande@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The existing implementation of qmp_send() requires the caller to provide
a buffer which is of word-aligned. The underlying reason for this is
that message ram only supports word accesses, but pushing this
requirement onto the clients results in the same boiler plate code
sprinkled in every call site.
By using a temporary buffer in qmp_send() we can hide the underlying
hardware limitations from the clients and allow them to pass their
NUL-terminates C string directly.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811205839.727373-2-quic_bjorande@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add device mode supported registers and masks.
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Reviewed-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/20230714042203.14251-2-quic_ptalari@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for handling the bus clocks in the icc driver, carve out
some defines and a struct definition to the common rpm header.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-4-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Use tabs for defines to make things spaced consistently.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-3-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add a preprocessor define to indicate the number of RPM contexts/states.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-2-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Avoid having to look up a dummy item from SMEM to detect if it is
already available or if we need to defer probing.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230531-rpm-rproc-v3-7-a07dcdefd918@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Nothing surprising in the SoC specific drivers, with the usual
updates:
- Added or improved SoC driver support for Tegra234, Exynos4121,
RK3588, as well as multiple Mediatek and Qualcomm chips
- SCMI firmware gains support for multiple SMC/HVC transport and
version 3.2 of the protocol
- Cleanups amd minor changes for the reset controller, memory
controller, firmware and sram drivers
- Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers"
* tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (118 commits)
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
tee: optee: Use kmemdup() to replace kmalloc + memcpy
soc: qcom: geni-se: Do not bother about enable/disable of interrupts in secondary sequencer
dt-bindings: sram: qcom,imem: document qdu1000
soc: qcom: icc-bwmon: Fix MSM8998 count unit
dt-bindings: soc: qcom,rpmh-rsc: Require power-domains
soc: qcom: socinfo: Add Soc ID for IPQ5300
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300
soc: qcom: Fix a IS_ERR() vs NULL bug in probe
soc: qcom: socinfo: Add support for new fields in revision 19
soc: qcom: socinfo: Add support for new fields in revision 18
dt-bindings: firmware: scm: Add compatible for SDX75
soc: qcom: mdt_loader: Fix split image detection
dt-bindings: memory-controllers: drop unneeded quotes
soc: rockchip: dtpm: use C99 array init syntax
firmware: tegra: bpmp: Add support for DRAM MRQ GSCs
soc/tegra: pmc: Use devm_clk_notifier_register()
soc/tegra: pmc: Simplify debugfs initialization
...
|
|
Merge series from Biju Das <biju.das.jz@bp.renesas.com>:
This patch series aims to add support for Renesas PMIC RAA215300 and
built-in RTC found on this PMIC device.
The details of PMIC can be found here[1].
Renesas PMIC RAA215300 exposes two separate i2c devices, one for the main
device and another for rtc device.
|
|
Add support for below fields coming in socinfo structure under v19:
* num_func_clusters: number of clusters with at least one functional core
* boot_cluster: cluster selected as boot cluster
* boot_core: core selected as boot core
While at it, rename some variables to align them with their
functionalities.
Signed-off-by: Naman Jain <quic_namajain@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230606134626.18790-3-quic_namajain@quicinc.com
|
|
Add support for below fields coming in socinfo structure under v18:
* num_kvps: number of key value pairs (KVP)
* kvps_offset: the offset of the KVP table from the base address of
socinfo structure in SMEM
KVP table has boolean values for certain feature flags, used to determine
hardware configuration.
Signed-off-by: Naman Jain <quic_namajain@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230606134626.18790-2-quic_namajain@quicinc.com
|
|
geni_se_rx_init_dma()
The geni_se_xx_dma_prep() interfaces necessarily do DMA mapping before
initiating DMA transfers. This is not suitable for spi where framework
is expected to handle map/unmap.
Expose new interfaces geni_se_xx_init_dma() which do only DMA transfer.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/1684325894-30252-2-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The LLCC EDAC register offsets varies between each SoC. Hardcoding the
register offsets won't work and will often result in crash due to
accessing the wrong locations.
Hence, get the register offsets from the LLCC driver matching the
individual SoCs.
Cc: <stable@vger.kernel.org> # 6.0: 5365cea199c7 ("soc: qcom: llcc: Rename reg_offset structs to reflect LLCC version")
Cc: <stable@vger.kernel.org> # 6.0: c13d7d261e36 ("soc: qcom: llcc: Pass LLCC version based register offsets to EDAC driver")
Cc: <stable@vger.kernel.org> # 6.0
Fixes: a6e9d7ef252c ("soc: qcom: llcc: Add configuration data for SM8450 SoC")
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230517114635.76358-3-manivannan.sadhasivam@linaro.org
|
|
Introduce a helper to return the SoC SMEM ID, which is used to identify the
exact SoC model as there may be differences in the same SoC family.
Currently, cpufreq-nvmem does this completely in the driver and there has
been more interest expresed for other drivers to use this information so
lets expose a common helper to prevent redoing it in individual drivers
since this field is present on every SMEM table version.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230526204802.3081168-3-robimarko@gmail.com
|
|
Move SMEM item struct and related defines to a header in order to be able
to reuse them in the SMEM driver instead of duplicating them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230526204802.3081168-1-robimarko@gmail.com
|
|
The Qualcomm LLCC/EDAC drivers were using a fixed register stride for
accessing the (Control and Status Registers) CSRs of each LLCC bank.
This stride only works for some SoCs like SDM845 for which driver
support was initially added.
But the later SoCs use different register stride that vary between the
banks with holes in-between. So it is not possible to use a single register
stride for accessing the CSRs of each bank. By doing so could result in a
crash.
For fixing this issue, let's obtain the base address of each LLCC bank from
devicetree and get rid of the fixed stride. This also means, there is no
need to rely on reg-names property and the base addresses can be obtained
using the index.
First index is LLCC bank 0 and last index is LLCC broadcast. If the SoC
supports more than one bank, then those need to be defined in devicetree
for index from 1..N-1.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Steev Klimaszewski <steev@kali.org> # Thinkpad X13s
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-13-manivannan.sadhasivam@linaro.org
|
|
From QUP HW Version 3.10 and above the Tx and Rx
fifo depth bits are increased to 23:16 bits from
21:16 bits in SE_HW_PARAM registers accomodating
256bytes of fifo depth.
Updated geni_se_get_tx_fifo_depth and
geni_se_get_rx_fifo_depth to retrieve right fifo
depth based on QUP HW version.
Signed-off-by: Visweswara Tanuku <quic_vtanuku@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230215050528.9507-1-quic_vtanuku@quicinc.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have one small patch to the clk core this time around. It fixes a
corner case with the CLK_OPS_PARENT_ENABLE flag combined with
clk_core_is_enabled() where it hangs the system. We'll simply assume
the clk is disabled if the parent is disabled and the flag is set.
Trying to turn on the parent to check the enable state of the clk runs
into system hangs at boot. We let this bake in -next for a couple
weeks to make sure there aren't any more issues because the last
attempt to fix this ran into hangs and had to be reverted.
Note: There were some more patches to the core framework around
sync_state and disabling unused clks, but I asked for that to be
reverted from the qcom PR because it isn't ready and we're still
discussing the best solution on the list.
Outside of the core clk framework, we have the usual collection of clk
driver updates and support for new SoCs (which seems to never stop).
The dirstat is dominated by Qualcomm because they added support for
quite a few SoCs this time around and also migrated quite a few of
their drivers to clk_parent_data. The other big diff is in the
Mediatek clk drivers that saw a significant rework this cycle to
similarly modernize the code, and we'll see that work continue in the
next cycle as well. Nothing really jumps out as scary here, except
that the significant churn in parent data descriptions can have typos
that go unnoticed. More details below.
Core:
- Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
New Drivers:
- Add a new clk-gpr-mux clock type and use it on i.MX6Q to add ENET
ref clocks
- Support for Mediatek MT7891 SoC clks
- Support for many Qualcomm clk controllers:
- QDU1000/QRU1000 global clock controller
- SA8775P global clock controller
- SM8550 TCSR and display clock controller
- SM6350 clock controller
- MSM8996 CBF and APCS clock controllers
Updates:
- Various cleanups and improvements to Mediatek clk drivers to reduce
code size and modernize the drivers
- Support for Versa 5P49V60 clks
- Disable R-Car H3 ES1.*, as it was only available to an internal
development group and needed a lot of quirks and workarounds
- Add PWM, Compare-Match Timer (TIM), USB, SDHI, and eMMC clocks and
resets on Renesas RZ/V2M
- Add display clocks on Renesas R-Car V4H
- Add Camera Receiving Unit (CRU) clocks and resets on Renesas RZ/G2L
- Free the imx_uart_clocks even if imx_register_uart_clocks returns
early
- Get the stdout clocks count from device tree on i.MX
- Drop the clock count argument from imx_register_uart_clocks()
- Keep the uart clocks on i.MX93 for when earlycon is used
- Fix SPDX comment in i.MX6SLL clocks bindings header
- Drop some unnecessary spaces from i.MX8ULP clocks bindings header
- Add imx_obtain_fixed_of_clock() for allowing to add a clock that is
not configured via devicetree
- Fix the ENET1 gate configuration for i.MX6UL according to the
reference manual
- Add ENET refclock mux support for i.MX6UL
- Add support for USB host/device configuration on Renesas RZ/N1
- Add PLL2 programming support, and CAN-FD clocks on Renesas R-Car
V4H
- Add D1 CAN bus gates and resets for Allwinner
- Mark D1 CPUX clock as critical on Allwinner
- Reuse D1 driver for Allwinner R528/T113
- Cleanup sunxi-ng Kconfig
- Fix sunxi-ng kernel-doc issues
- Model Allwinner H3/H5 DRAM clock as fixed clock
- Use .determine_rate() instead of .round_rate() for the dualdiv,
mpll, sclk-div and cpu-dyn-div amlogic clock drivers
- DDR clocks were marked as critical in the proper clock driver for
each AT91 SoC such that drivers/memory/atmel-sdramc.c to be deleted
in the next releases as it only does clock enablement
- Patch to avoid compiling dt-compat.o for all AT91 SoCs as only some
of them may use it
- Support synchronous power_off requests in the qcom GDSC driver for
proper GPU power collapse
- Drop test clocks from various Qualcomm clk drivers
- Update parent references to use clk_parent_data/clk_hw in various
Qualcomm clk drivers
- Fixes for the Qualcomm MSM8996 CPU clock controller
- Transition Qualcomm MSM8974 GCC off the externally defined
sleep_clk
- Add GDSCs in the global clock controller for Qualcomm QCS404
- The SDCC core clocks on Qualcomm SM6115 are moved to floor_ops
- Programming of clk_dis_wait for GPU CX GDSC on Qualcomm SC7180 and
SDM845 are moved to use the recently introduced properties in the
GDSC struct
- Qualcomm's RPMh clock driver gains SM8550 and SA8775P clocks, and
the IPA clock is added on a variety of platforms
- De-duplicate identical clks in Qualcomm SMD RPM clk driver
- Add a few missing clocks across msm8998, msm8992, msm8916, qcs404
to Qualcomm SDM RPM clk driver
- Various Qualcomm clk drivers use devm_pm_runtime_enable() to
simplify"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (228 commits)
clk: qcom: apcs-msm8986: Include bitfield.h for FIELD_PREP
clk: qcom: Revert sync_state based clk_disable_unused
clk: imx: pll14xx: fix recalc_rate for negative kdiv
clk: rs9: Drop unused pin_xin field
MAINTAINERS: clk: imx: Add Peng Fan as reviewer
clk: sprd: Add dependency for SPRD_UMS512_CLK
clk: ralink: fix 'mt7621_gate_is_enabled()' function
clk: mediatek: clk-mtk: Remove unneeded semicolon
dt-bindings: clock: remove stih416 bindings
dt-bindings: clock: add loongson-2 clock
dt-bindings: clock: add loongson-2 clock include file
clk: imx: fix compile testing imxrt1050
clk: Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
clk: imx: set imx_clk_gpr_mux_ops storage-class-specifier to static
clk: renesas: rcar-gen3: Disable R-Car H3 ES1.*
dt-bindings: clock: Merge qcom,gpucc-sm8350 into qcom,gpucc.yaml
clk: qcom: gpucc-sdm845: fix clk_dis_wait being programmed for CX GDSC
clk: qcom: gpucc-sc7180: fix clk_dis_wait being programmed for CX GDSC
dt-bindings: clock: qcom,sa8775p-gcc: add the power-domains property
clk: qcom: cpu-8996: add missing cputype include
...
|
|
Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drivers-for-6.3
|
|
The PMIC GLINK service runs on one of the co-processors of some modern
Qualcomm platforms and implements USB-C and battery managements. It uses
a message based protocol over GLINK for communication with the OS, hence
the name.
The driver implemented provides the rpmsg device for communication and
uses auxiliary bus to spawn off individual devices in respective
subsystem. The auxiliary devices are spawned off from a
platform_device, so that the drm_bridge is available early, to allow the
DisplayPort driver to probe even before the remoteproc has spun up.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM8350 PDX215
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-MTP & SM8450-HDK
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230201041853.1934355-3-quic_bjorande@quicinc.com
|
|
Since commit fc7a6209d571 ("bus: Make remove callback return void")
forces bus_type::remove be void-returned, it doesn't make much sense
for any bus based driver implementing remove callbalk to return
non-void to its caller.
As such, change the remove function for apr bus based drivers to
return void.
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/TYCP286MB23232B7968D34DB8323B0F16CAFB9@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
|
|
The commit 644c42295592 ("clk: qcom: smd: Add SM6375 clocks") added a
duplicate of the existing define QCOM_SMD_RPM_MMAXI_CLK, drop it now.
Fixes: 644c42295592 ("clk: qcom: smd: Add SM6375 clocks")
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209164855.128798-4-dmitry.baryshkov@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a quiet release for regulator, the diffstat is dominated by the
I2C migration to probe_new() and the newly added MT6357 driver. We've
just one framework addition and the rest is all new device support,
fixes and cleanups.
The framework addition is an API for requesting all regulators defined
in DT, this isn't great practice but has reasonable applications when
there is generic code handling devices on buses where the bus
specification doesn't include power. The immediate application is MDIO
but I believe there's others, it's another API that'll need an eye
keeping on it for undesirable usage.
Summary:
- An API for requesting all regulators defined in DT
- Conversion of lots of drivers to the I2C probe_new() API
- Support for Mediatek MT6357, Qualcomm PM8550, PMR735a and Richtek
RT6190"
* tag 'regulator-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (56 commits)
regulator: core: Use different devices for resource allocation and DT lookup
dt-bindings: Add missing 'unevaluatedProperties' to regulator nodes
regulator: qcom-labibb: Fix missing of_node_put() in qcom_labibb_regulator_probe()
regulator: add mt6357 regulator
regulator: dt-bindings: Add binding schema for mt6357 regulators
regulator: core: fix resource leak in regulator_register()
regulator: core: fix module refcount leak in set_supply()
regulator: core: fix use_count leakage when handling boot-on
regulator: rk808: Use dev_err_probe
regulator: rk808: reduce 'struct rk808' usage
regulator: Drop obsolete dependencies on COMPILE_TEST
regulator: pv88080-regulator: Convert to i2c's .probe_new()
regulator: pfuze100-regulator: Convert to i2c's .probe_new()
regulator: isl6271a-regulator: Convert to i2c's .probe_new()
regulator: fan53555: Convert to i2c's .probe_new()
regulator: act8865-regulator: Convert to i2c's .probe_new()
regulator: qcom-rpmh: Add support for PM8550 regulators
regulator: dt-bindings: qcom,rpmh: Add compatible for PM8550
regulator: tps65023-regulator: Convert to i2c's .probe_new()
regulator: tps62360-regulator: Convert to i2c's .probe_new()
...
|
|
Add LLCC configuration data for SM8550 SoC.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221116113005.2653284-4-abel.vesa@linaro.org
|
