Age | Commit message (Collapse) | Author |
|
phy_loopback() leaves it to the PHY driver to select the speed of the
loopback mode. Thus, the speed of the loopback mode depends on the PHY
driver in use.
Add support for speed selection to phy_loopback() to enable loopback
with defined speeds. Ensure that link up is signaled if speed changes
as speed is not allowed to change during link up. Link down and up is
necessary for a new speed.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20250312203010.47429-3-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PHY drivers support loopback mode, but it is not possible to select the
speed of the loopback mode. The speed is chosen by the set_loopback()
operation of the PHY driver. Same is valid for genphy_loopback().
There are PHYs that support loopback with different speeds. Extend
set_loopback() to make loopback speed selection possible.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250312203010.47429-2-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, netconsole has two methods of configuration - module
parameter and configfs. The former interface allows for netconsole
activation earlier during boot (by specifying the module parameter on
the kernel command line), so it is preferred for debugging issues which
arise before userspace is up/the configfs interface can be used. The
module parameter syntax requires specifying the egress interface name.
This requirement makes it hard to use for a couple reasons:
- The egress interface name can be hard or impossible to predict. For
example, installing a new network card in a system can change the
interface names assigned by the kernel.
- When constructing the module parameter, one may have trouble
determining the original (kernel-assigned) name of the interface
(which is the name that should be given to netconsole) if some stable
interface naming scheme is in effect. A human can usually look at
kernel logs to determine the original name, but this is very painful
if automation is constructing the parameter.
For these reasons, allow selection of the egress interface via MAC
address when configuring netconsole using the module parameter. Update
the netconsole documentation with an example of the new syntax.
Selection of egress interface by MAC address via configfs is far less
interesting (since when this interface can be used, one should be able
to easily convert between MAC address and interface name), so it is left
unimplemented.
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Tested-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250312-netconsole-v6-2-3437933e79b8@purestorage.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are a few places in the tree which compute the length of the
string representation of a MAC address as 3 * ETH_ALEN - 1. Define a
constant for this and use it where relevant. No functionality changes
are expected.
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@verge.net.au>
Link: https://patch.msgid.link/20250312-netconsole-v6-1-3437933e79b8@purestorage.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Lockdep complains about circular lock in 1 -> 2 -> 3 (see below).
Change the lock ordering to be:
- rtnl_lock
- dev_addr_sem
- netdev_ops (only for lower devices!)
- team_lock (or other per-upper device lock)
1. rtnl_lock -> netdev_ops -> dev_addr_sem
rtnl_setlink
rtnl_lock
do_setlink IFLA_ADDRESS on lower
netdev_ops
dev_addr_sem
2. rtnl_lock -> team_lock -> netdev_ops
rtnl_newlink
rtnl_lock
do_setlink IFLA_MASTER on lower
do_set_master
team_add_slave
team_lock
team_port_add
dev_set_mtu
netdev_ops
3. rtnl_lock -> dev_addr_sem -> team_lock
rtnl_newlink
rtnl_lock
do_setlink IFLA_ADDRESS on upper
dev_addr_sem
netif_set_mac_address
team_set_mac_address
team_lock
4. rtnl_lock -> netdev_ops -> dev_addr_sem
rtnl_lock
dev_ifsioc
dev_set_mac_address_user
__tun_chr_ioctl
rtnl_lock
dev_set_mac_address_user
tap_ioctl
rtnl_lock
dev_set_mac_address_user
dev_set_mac_address_user
netdev_lock_ops
netif_set_mac_address_user
dev_addr_sem
v2:
- move lock reorder to happen after kmalloc (Kuniyuki)
Cc: Kohei Enju <enjuk@amazon.com>
Fixes: df43d8bf1031 ("net: replace dev_addr_sem with netdev instance lock")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250312190513.1252045-3-sdf@fomichev.me
Tested-by: Lei Yang <leiyang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit df43d8bf10316a7c3b1e47e3cc0057a54df4a5b8.
Cc: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Fixes: df43d8bf1031 ("net: replace dev_addr_sem with netdev instance lock")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250312190513.1252045-2-sdf@fomichev.me
Tested-by: Lei Yang <leiyang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Allow platform glue to instruct stmmac to make use of the PHY transmit
clock stop capability when deciding whether to allow the transmit clock
from the DWMAC core to be stopped.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsITp-005vG9-Px@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
tcp_in_quickack_mode() is called from input path for small packets.
It calls __sk_dst_get() which reads sk->sk_dst_cache which has been
put in sock_read_tx group (for good reasons).
Then dst_metric(dst, RTAX_QUICKACK) also needs extra cache line misses.
Cache RTAX_QUICKACK in icsk->icsk_ack.dst_quick_ack to no longer pull
these cache lines for the cases a delayed ACK is scheduled.
After this patch TCP receive path does not longer access sock_read_tx
group.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250312083907.1931644-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the following patch, we no longer assume inet_frag_kill()
callers own a reference.
Consuming two refcounts from inet_frag_kill() would lead in UAF.
Propagate the pointer to the refs that will be consumed later
by the final inet_frag_putn() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250312082250.1803501-4-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
inet_frag_putn() can release multiple references
in one step.
Use it in inet_frags_free_cb().
Replace inet_frag_put(X) with inet_frag_putn(X, 1)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250312082250.1803501-2-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since commit a4ea4c477619 ("rxrpc: Don't use a ring buffer for call Tx
queue") this function is not used anymore.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250312063450.183652-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- drop batadv_priv_debug_log struct, by Sven Eckelmann
- adopt netdev_hold() / netdev_put(), by Eric Dumazet
- add support for jumbo frames, by Sven Eckelmann
- use consistent name for mesh interface, by Sven Eckelmann
- cleanup B.A.T.M.A.N. IV OGM aggregation handling,
by Sven Eckelmann (4 patches)
- add missing newlines for log macros, by Sven Eckelmann
* tag 'batadv-next-pullrequest-20250313' of git://git.open-mesh.org/linux-merge:
batman-adv: add missing newlines for log macros
batman-adv: Limit aggregation size to outgoing MTU
batman-adv: Use actual packet count for aggregated packets
batman-adv: Switch to bitmap helper for aggregation handling
batman-adv: Limit number of aggregated packets directly
batman-adv: Use consistent name for mesh interface
batman-adv: Add support for jumbo frames
batman-adv: adopt netdev_hold() / netdev_put()
batman-adv: Drop batadv_priv_debug_log struct
batman-adv: Start new development cycle
====================
Link: https://patch.msgid.link/20250313164519.72808-1-sw@simonwunderlich.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It's quite common to have a single UDP tunnel type active in the
whole system. In such a case we can replace the indirect call for
the UDP tunnel GRO callback with a static call.
Add the related accounting in the control path and switch to static
call when possible. To keep the code simple use a static array for
the registered tunnel types, and size such array based on the kernel
config.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/6fd1f9c7651151493ecab174e7b8386a1534170d.1741718157.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Most UDP tunnels bind a socket to a local port, with ANY address, no
peer and no interface index specified.
Additionally it's quite common to have a single tunnel device per
namespace.
Track in each namespace the UDP tunnel socket respecting the above.
When only a single one is present, store a reference in the netns.
When such reference is not NULL, UDP tunnel GRO lookup just need to
match the incoming packet destination port vs the socket local port.
The tunnel socket never sets the reuse[port] flag[s]. When bound to no
address and interface, no other socket can exist in the same netns
matching the specified local port.
Matching packets with non-local destination addresses will be
aggregated, and eventually segmented as needed - no behavior changes
intended.
Note that the UDP tunnel socket reference is stored into struct
netns_ipv4 for both IPv4 and IPv6 tunnels. That is intentional to keep
all the fastpath-related netns fields in the same struct and allow
cacheline-based optimization. Currently both the IPv4 and IPv6 socket
pointer share the same cacheline as the `udp_table` field.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/4d5c319c4471161829f50cb8436841de81a5edae.1741718157.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The phy_settings array is no longer relevant as it has now been replaced
by the link_caps array and associated phy_caps helpers.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-11-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use the newly introduced link_capabilities array to derive the list of
possible speeds when given a combination of linkmodes. As
link_capabilities is indexed by speed, we don't have to iterate the
whole phy_settings array.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-4-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
link_mode_params contains a lookup table of all 802.3 link modes that
are currently supported with structured data about each mode's speed,
duplex, number of lanes and mediums.
As a preparation for a port representation, export that table for the
rest of the net stack to use.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-2-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Expand on the requirements of the .pcs_config() method documentation,
specifically mentioning that it should cause minimal disruption to
an established link, and that it should return a positive non-zero
value when requiring the .pcs_an_restart() method to be called.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1trb24-005oVq-Is@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
These functions have never had a user, so remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/5792e2cd-6f0a-4f7d-a5ef-b932f94d82f3@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylib.h
These functions are used by PHY drivers only, therefore move their
declaration to phylib.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/406c8a20-b62e-4ee3-b174-b566724a0876@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for HW Steering action of flow meter range. Flow meters
range can use one HWS action for the whole range. Thus, share a cached
HWS action among rules that use same flow meter object range. Hold
refcount for each rule using the cached action.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/1741543663-22123-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Accurate ECN needs to send custom flags to handle IP-ECN
field reflection during handshake.
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ECN bits in TOS are always cleared when sending in ACKs in TW. Clearing
them is problematic for TCP flows that used Accurate ECN because ECN bits
decide which service queue the packet is placed into (L4S vs Classic).
Effectively, TW ACKs are always downgraded from L4S to Classic queue
which might impact, e.g., delay the ACK will experience on the path
compared with the other packets of the flow.
Change the TW ACK sending code to differentiate:
- In tcp_v4_send_reset(), commit ba9e04a7ddf4f ("ip: fix tos reflection
in ack and reset packets") cleans ECN bits for TW reset and this is
not affected.
- In tcp_v4_timewait_ack(), ECN bits for all TW ACKs are cleaned. But now
only ECN bits of ACKs for oow data or paws_reject are cleaned, and ECN
bits of other ACKs will not be cleaned.
- In tcp_v4_reqsk_send_ack(), commit 66b13d99d96a1 ("ipv4: tcp: fix TOS
value in ACK messages sent from TIME_WAIT") did not clean ECN bits of
ACKs for oow data or paws_reject. But now the ECN bits rae cleaned for
these ACKs.
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handling the CWR flag differs between RFC 3168 ECN and AccECN.
With RFC 3168 ECN aware TSO (NETIF_F_TSO_ECN) CWR flag is cleared
starting from 2nd segment which is incompatible how AccECN handles
the CWR flag. Such super-segments are indicated by SKB_GSO_TCP_ECN.
With AccECN, CWR flag (or more accurately, the ACE field that also
includes ECE & AE flags) changes only when new packet(s) with CE
mark arrives so the flag should not be changed within a super-skb.
The new skb/feature flags are necessary to prevent such TSO engines
corrupting AccECN ACE counters by clearing the CWR flag (if the
CWR handling feature cannot be turned off).
If NIC is completely unaware of RFC3168 ECN (doesn't support
NETIF_F_TSO_ECN) or its TSO engine can be set to not touch CWR flag
despite supporting also NETIF_F_TSO_ECN, TSO could be safely used
with AccECN on such NIC. This should be evaluated per NIC basis
(not done in this patch series for any NICs).
For the cases, where TSO cannot keep its hands off the CWR flag,
a GSO fallback is provided by this patch.
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create helpers for TCP ECN modes. No functional changes.
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With AccECN, there's one additional TCP flag to be used (AE)
and ACE field that overloads the definition of AE, CWR, and
ECE flags. As tcp_flags was previously only 1 byte, the
byte-order stuff needs to be added to it's handling.
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use BIT() macro for TCP flags field and TCP congestion control
flags that will be used by the congestion control algorithm.
No functional changes.
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Reviewed-by: Ilpo Järvinen <ij@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py")
de94e8697405 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0fa0 ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b9b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175ccad4 ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f913 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552eda ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d38e ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter, bluetooth and wireless.
No known regressions outstanding.
Current release - regressions:
- wifi: nl80211: fix assoc link handling
- eth: lan78xx: sanitize return values of register read/write
functions
Current release - new code bugs:
- ethtool: tsinfo: fix dump command
- bluetooth: btusb: configure altsetting for HCI_USER_CHANNEL
- eth: mlx5: DR, use the right action structs for STEv3
Previous releases - regressions:
- netfilter: nf_tables: make destruction work queue pernet
- gre: fix IPv6 link-local address generation.
- wifi: iwlwifi: fix TSO preparation
- bluetooth: revert "bluetooth: hci_core: fix sleeping function
called from invalid context"
- ovs: revert "openvswitch: switch to per-action label counting in
conntrack"
- eth:
- ice: fix switchdev slow-path in LAG
- bonding: fix incorrect MAC address setting to receive NS
messages
Previous releases - always broken:
- core: prevent TX of unreadable skbs
- sched: prevent creation of classes with TC_H_ROOT
- netfilter: nft_exthdr: fix offset with ipv4_find_option()
- wifi: cfg80211: cancel wiphy_work before freeing wiphy
- mctp: copy headers if cloned
- phy: nxp-c45-tja11xx: add errata for TJA112XA/B
- eth:
- bnxt: fix kernel panic in the bnxt_get_queue_stats{rx | tx}
- mlx5: bridge, fix the crash caused by LAG state check"
* tag 'net-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
net: mana: cleanup mana struct after debugfs_remove()
net/mlx5e: Prevent bridge link show failure for non-eswitch-allowed devices
net/mlx5: Bridge, fix the crash caused by LAG state check
net/mlx5: Lag, Check shared fdb before creating MultiPort E-Switch
net/mlx5: Fix incorrect IRQ pool usage when releasing IRQs
net/mlx5: HWS, Rightsize bwc matcher priority
net/mlx5: DR, use the right action structs for STEv3
Revert "openvswitch: switch to per-action label counting in conntrack"
net: openvswitch: remove misbehaving actions length check
selftests: Add IPv6 link-local address generation tests for GRE devices.
gre: Fix IPv6 link-local address generation.
netfilter: nft_exthdr: fix offset with ipv4_find_option()
selftests/tc-testing: Add a test case for DRR class with TC_H_ROOT
net_sched: Prevent creation of classes with TC_H_ROOT
ipvs: prevent integer overflow in do_ip_vs_get_ctl()
selftests: netfilter: skip br_netfilter queue tests if kernel is tainted
netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in insert_tree()
wifi: mac80211: fix MPDU length parsing for EHT 5/6 GHz
qlcnic: fix memory leak issues in qlcnic_sriov_common.c
rtase: Fix improper release of ring list entries in rtase_sw_reset
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Tariq Toukan says:
====================
mlx5-next updates 2025-03-10
The following pull-request contains common mlx5 updates for your *net-next* tree.
Please pull and let me know of any problem.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Add IFC bits for PPCNT recovery counters group
net/mlx5: fs, add RDMA TRANSPORT steering domain support
net/mlx5: Query ADV_RDMA capabilities
net/mlx5: Limit non-privileged commands
net/mlx5: Allow the throttle mechanism to be more dynamic
net/mlx5: Add RDMA_CTRL HW capabilities
====================
Link: https://patch.msgid.link/1741608293-41436-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As we move away from rtnl_lock for queue ops, introduce
per-netdev_nl_sock lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No functional changes. Next patches will add more granular locking
to netdev_nl_sock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a couple of places from which we can arrive to ndo_setup_tc
with TC_SETUP_BLOCK/TC_SETUP_FT:
- netlink
- netlink notifier
- netdev notifier
Locking netdev too deep in this call chain seems to be problematic
(especially assuming some/all of the call_netdevice_notifiers
NETDEV_UNREGISTER) might soon be running with the instance lock).
Revert to lockless ndo_setup_tc for TC_SETUP_BLOCK/TC_SETUP_FT. NFT
framework already takes care of most of the locking. Document
the assumptions.
ndo_setup_tc TC_SETUP_BLOCK
nft_block_offload_cmd
nft_chain_offload_cmd
nft_flow_block_chain
nft_flow_offload_chain
nft_flow_rule_offload_abort
nft_flow_rule_offload_commit
nft_flow_rule_offload_commit
nf_tables_commit
nfnetlink_rcv_batch
nfnetlink_rcv_skb_batch
nfnetlink_rcv
nft_offload_netdev_event
NETDEV_UNREGISTER notifier
ndo_setup_tc TC_SETUP_FT
nf_flow_table_offload_cmd
nf_flow_table_offload_setup
nft_unregister_flowtable_hook
nft_register_flowtable_net_hooks
nft_flowtable_update
nf_tables_newflowtable
nfnetlink_rcv_batch (.call NFNL_CB_BATCH)
nft_flowtable_update
nf_tables_newflowtable
nft_flowtable_event
nf_tables_flowtable_event
NETDEV_UNREGISTER notifier
__nft_unregister_flowtable_net_hooks
nft_unregister_flowtable_net_hooks
nf_tables_commit
nfnetlink_rcv_batch (.call NFNL_CB_BATCH)
__nf_tables_abort
nf_tables_abort
nfnetlink_rcv_batch
__nft_release_hook
__nft_release_hooks
nf_tables_pre_exit_net -> module unload
nft_rcv_nl_event
netlink_register_notifier (oh boy)
nft_register_flowtable_net_hooks
nft_flowtable_update
nf_tables_newflowtable
nf_tables_newflowtable
Fixes: c4f0f30b424e ("net: hold netdev instance lock during nft ndo_setup_tc")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reported-by: syzbot+0afb4bcf91e5a1afdcad@syzkaller.appspotmail.com
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250308044726.1193222-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When spanning datagram construction over multiple send calls using
MSG_MORE, per datagram settings are configured on the first send.
That is when ip(6)_setup_cork stores these settings for subsequent use
in __ip(6)_append_data and others.
The only flag that escaped this was dontfrag. As a result, a datagram
could be constructed with df=0 on the first sendmsg, but df=1 on a
next. Which is what cmsg_ip.sh does in an upcoming MSG_MORE test in
the "diff" scenario.
Changing datagram conditions in the middle of constructing an skb
makes this already complex code path even more convoluted. It is here
unintentional. Bring this flag in line with expected sockopt/cmsg
behavior.
And stop passing ipc6 to __ip6_append_data, to avoid such issues
in the future. This is already the case for __ip_append_data.
inet6_cork had a 6 byte hole, so the 1B flag has no impact.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250307033620.411611-3-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add recovery counters group layout of PPCNT (Ports Performance Counters
Register). This group counts recovery events per link. Also add the
corresponding bit in PCAM to indicate this group is supported.
Signed-off-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1741545697-23041-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"33 hotfixes. 24 are cc:stable and the remainder address post-6.13
issues or aren't considered necessary for -stable kernels.
26 are for MM and 7 are for non-MM.
- "mm: memory_failure: unmap poisoned folio during migrate properly"
from Ma Wupeng fixes a couple of two year old bugs involving the
migration of hwpoisoned folios.
- "selftests/damon: three fixes for false results" from SeongJae Park
fixes three one year old bugs in the SAMON selftest code.
The remainder are singletons and doubletons. Please see the individual
changelogs for details"
* tag 'mm-hotfixes-stable-2025-03-08-16-27' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (33 commits)
mm/page_alloc: fix uninitialized variable
rapidio: add check for rio_add_net() in rio_scan_alloc_net()
rapidio: fix an API misues when rio_add_net() fails
MAINTAINERS: .mailmap: update Sumit Garg's email address
Revert "mm/page_alloc.c: don't show protection in zone's ->lowmem_reserve[] for empty zone"
mm: fix finish_fault() handling for large folios
mm: don't skip arch_sync_kernel_mappings() in error paths
mm: shmem: remove unnecessary warning in shmem_writepage()
userfaultfd: fix PTE unmapping stack-allocated PTE copies
userfaultfd: do not block on locking a large folio with raised refcount
mm: zswap: use ATOMIC_LONG_INIT to initialize zswap_stored_pages
mm: shmem: fix potential data corruption during shmem swapin
mm: fix kernel BUG when userfaultfd_move encounters swapcache
selftests/damon/damon_nr_regions: sort collected regiosn before checking with min/max boundaries
selftests/damon/damon_nr_regions: set ops update for merge results check to 100ms
selftests/damon/damos_quota: make real expectation of quota exceeds
include/linux/log2.h: mark is_power_of_2() with __always_inline
NFS: fix nfs_release_folio() to not deadlock via kcompactd writeback
mm, swap: avoid BUG_ON in relocate_cluster()
mm: swap: use correct step in loop to wait all clusters in wait_for_allocation()
...
|
|
Add RX and TX RDMA_TRANSPORT flow table namespace, and the ability
to create flow tables in those namespaces.
The RDMA_TRANSPORT RX and TX are per vport.
Packets will traverse through RDMA_TRANSPORT_RX after RDMA_RX and through
RDMA_TRANSPORT_TX before RDMA_TX, ensuring proper control and management.
RDMA_TRANSPORT domains are managed by the vport group manager.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/a6b550d9859a197eafa804b9a8d76916ca481da9.1740574103.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Query ADV_RDMA capabilities which provide information for
advanced RDMA related features.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/e3e6ede03ea31cd201078dcdd4e407608e4a5a87.1740574103.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Limit non-privileged UID commands to half of the available command slots
when privileged UIDs are present.
Privileged throttle commands will not be limited.
Use an xarray to store privileged UIDs. Add insert and remove functions
for privileged UIDs management.
Non-user commands (with uid 0) are not limited.
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/d2f3dd9a0dbad3c9f2b4bb0723837995e4e06de2.1740574103.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Previously, throttle commands were identified and limited based on
opcode. These commands were limited to half the command slots using a
semaphore, and callback commands checked the opcode to determine
semaphore release.
To allow exceptions, we introduce a variable to indicate when the
throttle lock is held. This allows scenarios where throttle commands
are not limited. Callback functions use this variable to determine
if the throttle semaphore needs to be released.
This patch contains no functional changes. It's a preparation for the
next patch.
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Link: https://patch.msgid.link/055d975edeb816ac4c0fd1e665c6157d11947d26.1740574103.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Add RDMA_CTRL UCTX capabilities and add the RDMA_CTRL general object
type in hca_cap_2.
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Link: https://patch.msgid.link/ef7eb24be9a6f247ab52e8b4480350072e5182f5.1740574103.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Move the more esoteric helpers for netdev instance lock to
a dedicated header. This avoids growing netdevice.h to infinity
and makes rebuilding the kernel much faster (after touching
the header with the helpers).
The main netdev_lock() / netdev_unlock() functions are used
in static inlines in netdevice.h and will probably be used
most commonly, so keep them in netdevice.h.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250307183006.2312761-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netpoll tries to refill the skb queue on every packet send, independently
if packets are being consumed from the pool or not. This was
particularly problematic while being called from printk(), where the
operation would be done while holding the console lock.
Introduce a more intelligent approach to skb queue management. Instead
of constantly attempting to refill the queue, the system now defers
refilling to a work queue and only triggers the workqueue when a buffer
is actually dequeued. This change significantly reduces operations with
the lock held.
Add a work_struct to the netpoll structure for asynchronous refilling,
updating find_skb() to schedule refill work only when necessary (skb is
dequeued).
These changes have demonstrated a 15% reduction in time spent during
netpoll_send_msg operations, especially when no SKBs are not consumed
from consumed from pool.
When SKBs are being dequeued, the improvement is even better, around
70%, mainly because refilling the SKB pool is now happening outside of
the critical patch (with console_owner lock held).
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250304-netpoll_refill_v2-v1-1-06e2916a4642@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When introduced in commit 61723b393292 ("tcp: ulp: add functions to dump
ulp-specific information"), the whole ULP diag info has been exported
only if the requester had CAP_NET_ADMIN.
It looks like not everything is sensitive, and some info can be exported
to all users in order to ease the debugging from the userspace side
without requiring additional capabilities. Each layer should then decide
what can be exposed to everybody. The 'net_admin' boolean is then passed
to the different layers.
On kTLS side, it looks like there is nothing sensitive there: version,
cipher type, tx/rx user config type, plus some flags. So, only some
metadata about the configuration, no cryptographic info like keys, etc.
Then, everything can be exported to all users.
On MPTCP side, that's different. The MPTCP-related sequence numbers per
subflow should certainly not be exposed to everybody. For example, the
DSS mapping and ssn_offset would give all users on the system access to
narrow ranges of values for the subflow TCP sequence numbers and
MPTCP-level DSNs, and then ease packet injection. The TCP diag interface
doesn't expose the TCP sequence numbers for TCP sockets, so best to do
the same here. The rest -- token, IDs, flags -- can be exported to
everybody.
Acked-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250306-net-next-tcp-ulp-diag-net-admin-v1-2-06afdd860fc9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phylink_init_eee() is currently unused.
It was last added in 2019 by
commit 86e58135bc4a ("net: phylink: add phylink_init_eee() helper")
but it didn't actually wire a use up.
It had previous been removed in 2017 by
commit 939eae25d9a5 ("phylink: remove phylink_init_eee()").
Remove it again.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250306184534.246152-1-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Restore the previous behavior of the ACPI platform_profile sysfs
interface that has been changed recently in a way incompatible with
the existing user space (Mario Limonciello)"
* tag 'acpi-6.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
platform/x86/amd: pmf: Add balanced-performance to hidden choices
platform/x86/amd: pmf: Add 'quiet' to hidden choices
ACPI: platform_profile: Add support for hidden choices
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- TCP use after free fix on polling (Sagi)
- Controller memory buffer cleanup fixes (Icenowy)
- Free leaking requests on bad user passthrough commands (Keith)
- TCP error message fix (Maurizio)
- TCP corruption fix on partial PDU (Maurizio)
- TCP memory ordering fix for weakly ordered archs (Meir)
- Type coercion fix on message error for TCP (Dan)
- Name the RQF flags enum, fixing issues with anon enums and BPF import
of it
- ublk parameter setting fix
- GPT partition 7-bit conversion fix
* tag 'block-6.14-20250306' of git://git.kernel.dk/linux:
block: Name the RQF flags enum
nvme-tcp: fix signedness bug in nvme_tcp_init_connection()
block: fix conversion of GPT partition name to 7-bit
ublk: set_params: properly check if parameters can be applied
nvmet-tcp: Fix a possible sporadic response drops in weakly ordered arch
nvme-tcp: fix potential memory corruption in nvme_tcp_recv_pdu()
nvme-tcp: Fix a C2HTermReq error message
nvmet: remove old function prototype
nvme-ioctl: fix leaked requests on mapping error
nvme-pci: skip CMB blocks incompatible with PCI P2P DMA
nvme-pci: clean up CMBMSC when registering CMB fails
nvme-tcp: fix possible UAF in nvme_tcp_poll
|
|
This reverts commit 4d94f05558271654670d18c26c912da0c1c15549 which has
problems (see [1]) and is no longer needed since 581dd2dc168f
("Bluetooth: hci_event: Fix using rcu_read_(un)lock while iterating")
has reworked the code where the original bug has been found.
[1] Link: https://lore.kernel.org/linux-bluetooth/877c55ci1r.wl-tiwai@suse.de/T/#t
Fixes: 4d94f0555827 ("Bluetooth: hci_core: Fix sleeping function called from invalid context")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The fix to atomically read the pipe head and tail state when not holding
the pipe mutex has caused a number of headaches due to the size change
of the involved types.
It turns out that we don't have _that_ many places that access these
fields directly and were affected, but we have more than we strictly
should have, because our low-level helper functions have been designed
to have intimate knowledge of how the pipes work.
And as a result, that random noise of direct 'pipe->head' and
'pipe->tail' accesses makes it harder to pinpoint any actual potential
problem spots remaining.
For example, we didn't have a "is the pipe full" helper function, but
instead had a "given these pipe buffer indexes and this pipe size, is
the pipe full". That's because some low-level pipe code does actually
want that much more complicated interface.
But most other places literally just want a "is the pipe full" helper,
and not having it meant that those places ended up being unnecessarily
much too aware of this all.
It would have been much better if only the very core pipe code that
cared had been the one aware of this all.
So let's fix it - better late than never. This just introduces the
trivial wrappers for "is this pipe full or empty" and to get how many
pipe buffers are used, so that instead of writing
if (pipe_full(pipe->head, pipe->tail, pipe->max_usage))
the places that literally just want to know if a pipe is full can just
say
if (pipe_is_full(pipe))
instead. The existing trivial cases were converted with a 'sed' script.
This cuts down on the places that access pipe->head and pipe->tail
directly outside of the pipe code (and core splice code) quite a lot.
The splice code in particular still revels in doing the direct low-level
accesses, and the fuse fuse_dev_splice_write() code also seems a bit
unnecessarily eager to go very low-level, but it's at least a bit better
than it used to be.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix racy non-atomic read-then-increment operation with
PREEMPT_RT in nft_ct, from Sebastian Andrzej Siewior.
2) GC is not skipped when jiffies wrap around in nf_conncount,
from Nicklas Bo Jensen.
3) flush_work() on nf_tables_destroy_work waits for the last queued
instance, this could be an instance that is different from the one
that we must wait for, then make destruction work queue.
* tag 'nf-25-03-06' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: make destruction work queue pernet
netfilter: nf_conncount: garbage collection is not skipped when jiffies wrap around
netfilter: nft_ct: Use __refcount_inc() for per-CPU nft_ct_pcpu_template.
====================
Link: https://patch.msgid.link/20250306153446.46712-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|