| Age | Commit message (Collapse) | Author |
|---|
|
With this patch, vti6 uses the IPsec protocol multiplexer to
register its own receive side hooks for ESP, AH and IPCOMP.
Vti6 now does the following on receive side:
1. Do an input policy check for the IPsec packet we received.
This is required because this packet could be already
prosecces by IPsec, so an inbuond policy check is needed.
2. Mark the packet with the i_key. The policy and the state
must match this key now. Policy and state belong to the vti
namespace and policy enforcement is done at the further layers.
3. Call the generic xfrm layer to do decryption and decapsulation.
4. Wait for a callback from the xfrm layer to properly clean the
skb to not leak informations on namespace transitions and
update the device statistics.
On transmit side:
1. Mark the packet with the o_key. The policy and the state
must match this key now.
2. Do a xfrm_lookup on the original packet with the mark applied.
3. Check if we got an IPsec route.
4. Clean the skb to not leak informations on namespace
transitions.
5. Attach the dst_enty we got from the xfrm_lookup to the skb.
6. Call dst_output to do the IPsec processing.
7. Do the device statistics.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Unlike ip6_tunnel, vti6 does not use the the tunnel
endpoint addresses to do route and xfrm lookups.
So no need to cache the flow informations. It also
does not make sense to calculate the mtu based on
such flow informations, so remove this too.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Unlike ip6_tunnel, vti6 can lookup multiple different dst entries,
dependent of the configured xfrm states. Therefore it does not make
sense to cache a dst_entry.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Switch ipcomp6 to use the new IPsec protocol multiplexer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Switch ah6 to use the new IPsec protocol multiplexer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Switch esp6 to use the new IPsec protocol multiplexer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
This patch adds an IPsec protocol multiplexer for ipv6. With
this it is possible to add alternative protocol handlers, as
needed for IPsec virtual tunnel interfaces.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore
age needs to be added to the condition.
Age calculation in ipv6_create_tempaddr is different from the one
in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS.
This can cause age in ipv6_create_tempaddr to be less than the one
in addrconf_verify and therefore unnecessary temporary address to
be generated.
Use age calculation as in addrconf_modify to avoid this.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets which have L2 address different from ours should be
already filtered before entering into ip6_forward().
Perform that check at the beginning to avoid processing such packets.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DST_NOCOUNT should only be used if an authorized user adds routes
locally. In case of routes which are added on behalf of router
advertisments this flag must not get used as it allows an unlimited
number of routes getting added remotely.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this fix, ipv6_exthdrs_offload_init doesn't register IPPROTO_DSTOPTS
offload, but returns 0 (as the IPPROTO_ROUTING registration actually succeeds).
This then causes the ipv6_gso_segment to drop IPv6 packets with IPPROTO_DSTOPTS
header.
The issue detected and the fix verified by running MS HCK Offload LSO test on
top of QEMU Windows guests, as this test sends IPv6 packets with
IPPROTO_DSTOPTS.
Signed-off-by: Anton Nayshtut <anton@swortex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e688a604807647 ("net: introduce DST_NOPEER dst flag") introduced
DST_NOPEER because because of crashes in ipv6_select_ident called from
udp6_ufo_fragment.
Since commit 916e4cf46d0204 ("ipv6: reuse ip6_frag_id from
ip6_ufo_append_data") we don't call ipv6_select_ident any more from
ip6_ufo_append_data, thus this flag lost its purpose and can be removed.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the following snmp stats:
TCPFastOpenActiveFail: Fast Open attempts (SYN/data) failed beacuse
the remote does not accept it or the attempts timed out.
TCPSynRetrans: number of SYN and SYN/ACK retransmits to break down
retransmissions into SYN, fast-retransmits, timeout retransmits, etc.
TCPOrigDataSent: number of outgoing packets with original data (excluding
retransmission but including data-in-SYN). This counter is different from
TcpOutSegs because TcpOutSegs also tracks pure ACKs. TCPOrigDataSent is
more useful to track the TCP retransmission rate.
Change TCPFastOpenActive to track only successful Fast Opens to be symmetric to
TCPFastOpenPassive.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Lawrence Brakmo <brakmo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 9195bb8e381d81d5a315f911904cdf0cfcc919b8 ("ipv6: improve
ipv6_find_hdr() to skip empty routing headers") broke ipv6_find_hdr().
When a target is specified like IPPROTO_ICMPV6 ipv6_find_hdr()
returns -ENOENT when it's found, not the header as expected.
A part of IPVS is broken and possible also nft_exthdr_eval().
When target is -1 which it is most cases, it works.
This patch exits the do while loop if the specific header is found
so the nexthdr could be returned as expected.
Reported-by: Art -kwaak- van Breemen <ard@telegraafnet.nl>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
CC:Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
1) Build fix for ip_vti when NET_IP_TUNNEL is not set.
We need this set to have ip_tunnel_get_stats64()
available.
2) Fix a NULL pointer dereference on sub policy usage.
We try to access a xfrm_state from the wrong array.
3) Take xfrm_state_lock in xfrm_migrate_state_find(),
we need it to traverse through the state lists.
4) Clone states properly on migration, otherwise we crash
when we migrate a state with aead algorithm attached.
5) Fix unlink race when between thread context and timer
when policies are deleted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This option has the same semantic as IP_PMTUDISC_OMIT for IPv4 which
got recently introduced. It doesn't honor the path mtu discovered by the
host but in contrary to IPV6_PMTUDISC_INTERFACE allows the generation of
fragments if the packet size exceeds the MTU of the outgoing interface
MTU.
Fixes: 93b36cf3425b9b ("ipv6: support IPV6_PMTU_INTERFACE on sockets")
Cc: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These info messages are rather pointless without any means to identify
the source of the bogus packets. Logging the src and dst addresses and
ports may help a bit.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the UFO fragmentation process does not correctly handle inner
UDP frames.
(The following tcpdumps are captured on the parent interface with ufo
disabled while tunnel has ufo enabled, 2000 bytes payload, mtu 1280,
both sit device):
IPv6:
16:39:10.031613 IP (tos 0x0, ttl 64, id 3208, offset 0, flags [DF], proto IPv6 (41), length 1300)
192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 1240) 2001::1 > 2001::8: frag (0x00000001:0|1232) 44883 > distinct: UDP, length 2000
16:39:10.031709 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPv6 (41), length 844)
192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 784) 2001::1 > 2001::8: frag (0x00000001:0|776) 58979 > 46366: UDP, length 5471
We can see that fragmentation header offset is not correctly updated.
(fragmentation id handling is corrected by 916e4cf46d0204 ("ipv6: reuse
ip6_frag_id from ip6_ufo_append_data")).
IPv4:
16:39:57.737761 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPIP (4), length 1296)
192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57034, offset 0, flags [none], proto UDP (17), length 1276)
192.168.99.1.35961 > 192.168.99.2.distinct: UDP, length 2000
16:39:57.738028 IP (tos 0x0, ttl 64, id 3210, offset 0, flags [DF], proto IPIP (4), length 792)
192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57035, offset 0, flags [none], proto UDP (17), length 772)
192.168.99.1.13531 > 192.168.99.2.20653: UDP, length 51109
In this case fragmentation id is incremented and offset is not updated.
First, I aligned inet_gso_segment and ipv6_gso_segment:
* align naming of flags
* ipv6_gso_segment: setting skb->encapsulation is unnecessary, as we
always ensure that the state of this flag is left untouched when
returning from upper gso segmenation function
* ipv6_gso_segment: move skb_reset_inner_headers below updating the
fragmentation header data, we don't care for updating fragmentation
header data
* remove currently unneeded comment indicating skb->encapsulation might
get changed by upper gso_segment callback (gre and udp-tunnel reset
encapsulation after segmentation on each fragment)
If we encounter an IPIP or SIT gso skb we now check for the protocol ==
IPPROTO_UDP and that we at least have already traversed another ip(6)
protocol header.
The reason why we have to special case GSO_IPIP and GSO_SIT is that
we reset skb->encapsulation to 0 while skb_mac_gso_segment the inner
protocol of GSO_UDP_TUNNEL or GSO_GRE packets.
Reported-by: Wolfgang Walter <linux@stwm.de>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
1) Introduce skb_to_sgvec_nomark function to add further data to the sg list
without calling sg_unmark_end first. Needed to add extended sequence
number informations. From Fan Du.
2) Add IPsec extended sequence numbers support to the Authentication Header
protocol for ipv4 and ipv6. From Fan Du.
3) Make the IPsec flowcache namespace aware, from Fan Du.
4) Avoid creating temporary SA for every packet when no key manager is
registered. From Horia Geanta.
5) Support filtering of SA dumps to show only the SAs that match a
given filter. From Nicolas Dichtel.
6) Remove caching of xfrm_policy_sk_bundles. The cached socket policy bundles
are never used, instead we create a new cache entry whenever xfrm_lookup()
is called on a socket policy. Most protocols cache the used routes to the
socket, so this caching is not needed.
7) Fix a forgotten SADB_X_EXT_FILTER length check in pfkey, from Nicolas
Dichtel.
8) Cleanup error handling of xfrm_state_clone.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we generate a new fragmentation id on UFO segmentation. It
is pretty hairy to identify the correct net namespace and dst there.
Especially tunnels use IFF_XMIT_DST_RELEASE and thus have no skb_dst
available at all.
This causes unreliable or very predictable ipv6 fragmentation id
generation while segmentation.
Luckily we already have pregenerated the ip6_frag_id in
ip6_ufo_append_data and can use it here.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug introduced by commit 7d442fab0a67 ("ipv4: Cache dst in tunnels").
Because sit code does not call ip_tunnel_init(), the dst_cache was not
initialized.
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 469bdcefdc47a ip6_vti uses ip_tunnel_get_stats64(),
so we need to select NET_IP_TUNNEL to have this function available.
Fixes: 469bdcefdc ("ipv6: fix the use of pcpu_tstats in ip6_vti.c")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
* Fix nf_trace in nftables if XT_TRACE=n, from Florian Westphal.
* Don't use the fast payload operation in nf_tables if the length is
not power of 2 or it is not aligned, from Nikolay Aleksandrov.
* Fix missing break statement the inet flavour of nft_reject, which
results in evaluating IPv4 packets with the IPv6 evaluation routine,
from Patrick McHardy.
* Fix wrong kconfig symbol in nft_meta to match the routing realm,
from Paul Bolle.
* Allocate the NAT null binding when creating new conntracks via
ctnetlink to avoid that several packets race at initializing the
the conntrack NAT extension, original patch from Florian Westphal,
revisited version from me.
* Fix DNAT handling in the snmp NAT helper, the same handling was being
done for SNAT and DNAT and 2.4 already contains that fix, from
Francois-Xavier Le Bail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These include are here since kernel 2.2.7, but probably never used.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This bug was reported by Steinar H. Gunderson and was introduced by commit
f7cb8886335d ("sit/gre6: don't try to add the same route two times").
root@morgental:~# ip tunnel add foo mode gre remote 1.2.3.4 ttl 64
root@morgental:~# ip link set foo up mtu 1468
root@morgental:~# ip -6 route show dev foo
fe80::/64 proto kernel metric 256
but after the above commit, no such route shows up.
There is no link local route because dev->dev_addr is 0 (because local ipv4
address is 0), hence no link local address is configured.
In this scenario, the link local address is added manually: 'ip -6 addr add
fe80::1 dev foo' and because prefix is /128, no link local route is added by the
kernel.
Even if the right things to do is to add the link local address with a /64
prefix, we need to restore the previous behavior to avoid breaking userpace.
Reported-by: Steinar H. Gunderson <sesse@samfundet.no>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using nftables with CONFIG_NETFILTER_XT_TARGET_TRACE=n, we get
lots of "TRACE: filter:output:policy:1 IN=..." warnings as several
places will leave skb->nf_trace uninitialised.
Unlike iptables tracing functionality is not conditional in nftables,
so always copy/zero nf_trace setting when nftables is enabled.
Move this into __nf_copy() helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marcelo Ricardo Leitner reported problems when the forwarding link path
has a lower mtu than the incoming one if the inbound interface supports GRO.
Given:
Host <mtu1500> R1 <mtu1200> R2
Host sends tcp stream which is routed via R1 and R2. R1 performs GRO.
In this case, the kernel will fail to send ICMP fragmentation needed
messages (or pkt too big for ipv6), as GSO packets currently bypass dstmtu
checks in forward path. Instead, Linux tries to send out packets exceeding
the mtu.
When locking route MTU on Host (i.e., no ipv4 DF bit set), R1 does
not fragment the packets when forwarding, and again tries to send out
packets exceeding R1-R2 link mtu.
This alters the forwarding dstmtu checks to take the individual gso
segment lengths into account.
For ipv6, we send out pkt too big error for gso if the individual
segments are too big.
For ipv4, we either send icmp fragmentation needed, or, if the DF bit
is not set, perform software segmentation and let the output path
create fragments when the packet is leaving the machine.
It is not 100% correct as the error message will contain the headers of
the GRO skb instead of the original/segmented one, but it seems to
work fine in my (limited) tests.
Eric Dumazet suggested to simply shrink mss via ->gso_size to avoid
sofware segmentation.
However it turns out that skb_segment() assumes skb nr_frags is related
to mss size so we would BUG there. I don't want to mess with it considering
Herbert and Eric disagree on what the correct behavior should be.
Hannes Frederic Sowa notes that when we would shrink gso_size
skb_segment would then also need to deal with the case where
SKB_MAX_FRAGS would be exceeded.
This uses sofware segmentation in the forward path when we hit ipv4
non-DF packets and the outgoing link mtu is too small. Its not perfect,
but given the lack of bug reports wrt. GRO fwd being broken this is a
rare case anyway. Also its not like this could not be improved later
once the dust settles.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add esn support for AH input stage by attaching upper 32bits
sequence number right after packet payload as specified by RFC 4302.
Then the ICV value will guard upper 32bits sequence number as well when
packet going in.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
This patch add esn support for AH output stage by attaching upper 32bits
sequence number right after packet payload as specified by RFC 4302.
Then the ICV value will guard upper 32bits sequence number as well when
packet going out.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The patch 446fab59333dea91e54688f033dd8d788d0486fb ("ipv6: enable anycast addresses
as source addresses in ICMPv6 error messages") causes an Oops when pinging a not
set up IPv6 peer on a sit tunnel.
The problem is that ipv6_anycast_destination() uses unconditionally skb_dst(skb),
which is NULL in this case.
The solution is to use instead the ipv6_chk_acast_addr_src() function.
Here are the steps to reproduce it:
modprobe sit
ip link add sit1 type sit remote 10.16.0.121 local 10.16.0.249
ip l s sit1 up
ip -6 a a dev sit1 2001:1234::123 remote 2001:1234::121
ping6 2001:1234::121
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a reject module for NFPROTO_INET. It does nothing but dispatch
to the AF-specific modules based on the hook family.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently the nft_reject module depends on symbols from ipv6. This is
wrong since no generic module should force IPv6 support to be loaded.
Split up the module into AF-specific and a generic part.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
I see a memory leak when using a transparent HTTP proxy using TPROXY
together with TCP early demux and Kernel v3.8.13.15 (Ubuntu stable):
unreferenced object 0xffff88008cba4a40 (size 1696):
comm "softirq", pid 0, jiffies 4294944115 (age 8907.520s)
hex dump (first 32 bytes):
0a e0 20 6a 40 04 1b 37 92 be 32 e2 e8 b4 00 00 .. j@..7..2.....
02 00 07 01 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff810b710a>] kmem_cache_alloc+0xad/0xb9
[<ffffffff81270185>] sk_prot_alloc+0x29/0xc5
[<ffffffff812702cf>] sk_clone_lock+0x14/0x283
[<ffffffff812aaf3a>] inet_csk_clone_lock+0xf/0x7b
[<ffffffff8129a893>] netlink_broadcast+0x14/0x16
[<ffffffff812c1573>] tcp_create_openreq_child+0x1b/0x4c3
[<ffffffff812c033e>] tcp_v4_syn_recv_sock+0x38/0x25d
[<ffffffff812c13e4>] tcp_check_req+0x25c/0x3d0
[<ffffffff812bf87a>] tcp_v4_do_rcv+0x287/0x40e
[<ffffffff812a08a7>] ip_route_input_noref+0x843/0xa55
[<ffffffff812bfeca>] tcp_v4_rcv+0x4c9/0x725
[<ffffffff812a26f4>] ip_local_deliver_finish+0xe9/0x154
[<ffffffff8127a927>] __netif_receive_skb+0x4b2/0x514
[<ffffffff8127aa77>] process_backlog+0xee/0x1c5
[<ffffffff8127c949>] net_rx_action+0xa7/0x200
[<ffffffff81209d86>] add_interrupt_randomness+0x39/0x157
But there are many more, resulting in the machine going OOM after some
days.
From looking at the TPROXY code, and with help from Florian, I see
that the memory leak is introduced in tcp_v4_early_demux():
void tcp_v4_early_demux(struct sk_buff *skb)
{
/* ... */
iph = ip_hdr(skb);
th = tcp_hdr(skb);
if (th->doff < sizeof(struct tcphdr) / 4)
return;
sk = __inet_lookup_established(dev_net(skb->dev), &tcp_hashinfo,
iph->saddr, th->source,
iph->daddr, ntohs(th->dest),
skb->skb_iif);
if (sk) {
skb->sk = sk;
where the socket is assigned unconditionally to skb->sk, also bumping
the refcnt on it. This is problematic, because in our case the skb
has already a socket assigned in the TPROXY target. This then results
in the leak I see.
The very same issue seems to be with IPv6, but haven't tested.
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 25fb6ca4ed9cad72f14f61629b68dc03c0d9713f
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
allocates addrconf router for ipv6 address when lo device up.
but commit a881ae1f625c599b460cc8f8a7fcb1c438f699ad
"ipv6:don't call addrconf_dst_alloc again when enable lo" breaks
this behavior.
Since the addrconf router is moved to the garbage list when
lo device down, we should release this router and rellocate
a new one for ipv6 address when lo device up.
This patch solves bug 67951 on bugzilla
https://bugzilla.kernel.org/show_bug.cgi?id=67951
change from v1:
use ip6_rt_put to repleace ip6_del_rt, thanks Hannes!
change code style, suggested by Sergei.
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change allows to consider an anycast address valid as source address
when given via an IPV6_PKTINFO or IPV6_2292PKTINFO ancillary data item.
So, when sending a datagram with ancillary data, the unicast and anycast
addresses are handled in the same way.
- Adds ipv6_chk_acast_addr_src() to check if an anycast address is link-local
on given interface or is global.
- Uses it in ip6_datagram_send_ctl().
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some ipv6 protocols cannot handle ipv4 addresses, so we must not allow
connecting and binding to them. sendmsg logic does already check msg->name
for this but must trust already connected sockets which could be set up
for connection to ipv4 address family.
Per-socket flag ipv6only is of no use here, as it is under users control
by setsockopt.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Uses ipv6_anycast_destination() in icmp6_send().
Suggested-by: Bill Fink <billfink@mindspring.com>
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As tcp_rcv_state_process() has already calls tcp_mtup_init() for non-fastopen
sock, we can delete the redundant calls of tcp_mtup_init() in
tcp_{v4,v6}_syn_recv_sock().
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv6_link_dev_addr sorts newly added addresses by scope in
ifp->addr_list. Smaller scope addresses are added to the tail of the
list. Use this fact to iterate in reverse over addr_list and break out
as soon as a higher scoped one showes up, so we can spare some cycles
on machines with lot's of addresses.
The ordering of the addresses is not relevant and we are more likely to
get the eui64 generated address with this change anyway.
Suggested-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently don't report IPV6_RECVPKTINFO in cmsg access ancillary data
for IPv4 datagrams on IPv6 sockets.
This patch splits the ip6_datagram_recv_ctl into two functions, one
which handles both protocol families, AF_INET and AF_INET6, while the
ip6_datagram_recv_specific_ctl only handles IPv6 cmsg data.
ip6_datagram_recv_*_ctl never reported back any errors, so we can make
them return void. Also provide a helper for protocols which don't offer dual
personality to further use ip6_datagram_recv_ctl, which is exported to
modules.
I needed to shuffle the code for ping around a bit to make it easier to
implement dual personality for ping ipv6 sockets in future.
Reported-by: Gert Doering <gert@space.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the introduction of IPV6_FL_F_REFLECT, there is no guarantee of
flow label unicity. This patch introduces a new sysctl to protect the old
behaviour, enable by default.
Changelog of V3:
* rename ip6_flowlabel_consistency to flowlabel_consistency
* use net_info_ratelimited()
* checkpatch cleanups
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This information is already available via IPV6_FLOWINFO
of IPV6_2292PKTOPTIONS, and them a filtering to get the flow label
information. But it is probably logical and easier for users to add this
here, and to control both sent/received flow label values with the
IPV6_FLOWLABEL_MGR option.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this option, the socket will reply with the flow label value read
on received packets.
The goal is to have a connection with the same flow label in both
direction of the communication.
Changelog of V4:
* Do not erase the flow label on the listening socket. Use pktopts to
store the received value
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
