| Age | Commit message (Collapse) | Author |
|---|
|
Instead of calculating the new primary 40/80/160 MHz
center frequency here, use the new helper function from
cfg80211.
Link: https://msgid.link/20240129194108.eb59d6433d18.I74b745f0d1a32e779fb25d50c56407be7c35b840@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a new inline helper function to ieee80211.h to
extract the disabled subchannels bitmap from an EHT
operation element, and use that in mac80211 where
we do that.
Link: https://msgid.link/20240129194108.d9f50dcec8d0.I8b08cbc2490a734fafcce0fa0fc328211ba6f10b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Due to the earlier restructuring we now mostly ignore
the channel configuration in the association response,
apart from the HT/VHT checks we had.
Don't do that, but parse it and update, also dropping the
association if the AP changed its mode in the response.
Link: https://msgid.link/20240129194108.b3efa5eae60c.I1b70c9fd56781b22cdfdca55d34d69f7d0733e31@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
EHT requires that stations are able to participate in
wider bandwidth OFDMA, i.e. parse downlink OFDMA and
uplink OFDMA triggers when they're not capable of (or
not connected at) the (wider) bandwidth that the AP
is using. This requires hardware configuration, since
the entity responsible for parsing (possibly hardware)
needs to know the AP bandwidth.
To support this, change the channel request to have
the AP's bandwidth for clients, and track that in the
channel context in mac80211. This means that the same
chandef might need to be split up into two different
contexts, if the APs are different. Interfaces other
than client are not participating in OFDMA the same
way, so they don't request any AP setting.
Note that this doesn't introduce any API to split a
channel context, so that there are cases where this
might lead to a disconnect, e.g. if there are two
client interfaces using the same channel context, e.g.
both 160 MHz connected to different 320 MHz APs, and
one of the APs switches to 160 MHz.
Note also there are possible cases where this can be
optimised, e.g. when using the upper or lower 160 Mhz,
but I haven't been able to really fully understand the
spec and/or hardware limitations.
If, for some reason, there are no hardware limits on
this because the OFDMA (downlink/trigger) parsing is
done in firmware and can take the transmitter into
account, then drivers can set the new flag
IEEE80211_VIF_IGNORE_OFDMA_WIDER_BW on interfaces to
not have them request any AP bandwidth in the channel
context and ignore this issue entirely. The bss_conf
still contains the AP configuration (if any, i.e. EHT)
in the chanreq.
Link: https://msgid.link/20240129194108.d3d5b35dd783.I939d04674f4ff06f39934b1591c8d36a30ce74c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the channel context code we have quite a few instances
of nested loops iterating the interfaces and then links.
Add a new for_each_sdata_link() macro and use it. Also,
since it's easier, convert all the loops and a few other
places away from RCU as we now hold the wiphy mutex
everywhere anyway.
This does cause a little bit more work (such as checking
interface types for each link of an interface rather than
not iterating links in some cases), but that's not a huge
issue and seems like an acceptable trade-off, readability
is important too.
Link: https://msgid.link/20240129194108.7240829bd96d.I5ccbb8dd019cbcb5326c85d76121359225d6541a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The last caller of this with a NULL argument was related to
the non-chanctx code, so we can now remove this odd logic.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129194108.bad8ec1e76c8.I12287452f42c54baf75821e75491cf6d021af20a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are still surprisingly many non-chanctx drivers, but in
mac80211 that code is a bit awkward. Simplify this by having
those drivers assign 'emulated' ops, so that the mac80211 code
can be more unified between non-chanctx/chanctx drivers. This
cuts the number of places caring about it by about 15, which
are scattered across - now they're fewer and no longer in the
channel context handling.
Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the code we currently check for support 80+80, 160
and 320 channel widths, but really the way this should
be (and is otherwise) handled is that we compute the
highest channel bandwidth given there, and then cut it
down to what we support. This is also needed for wider
bandwidth OFDMA support.
Change the code to remove this limitation and always
parse the highest possible channel width.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129194108.d06f85082e29.I47e68ed3d97b0a2f4ee61e5d8abfcefc8a5b9c08@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Rewrite the station-side connection handling. The connection
flags (IEEE80211_DISABLE_*) are rather confusing, and they're
not always maintained well. Additionally, for wider-bandwidth
OFDMA support we need to know the precise bandwidth of the AP,
which is currently somewhat difficult.
Rewrite this to have a 'mode' (S1G/legacy/HT/...) and a limit
on the bandwidth. This is not entirely clean because some of
those modes aren't completely sequenced (as this assumes in
some places), e.g. VHT doesn't exist on 2.4 GHz, but HE does.
However, it still simplifies things and gives us a good idea
what we're operating as, so we can parse elements accordingly
etc.
This leaves a FIXME for puncturing, this is addressed in a
later patch.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129194108.9451722c0110.I3e61f4cfe9da89008e1854160093c76a1e69dc2a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Most devices now do duration calculations, so we don't hit
this code at all any more. Clearly the approach of warning
at compile time here when new bands are added didn't work,
the new bands were just added with "TODO". Clean it up, it
won't matter for new bands since they'll just not have any
need to calculate durations in software.
While at it, also clean up and unify the code a bit.
Link: https://msgid.link/20240129194108.70a97bd69265.Icdd8b0ac60a382244466510090eb0f5868151f39@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Not sure how this happened or how nothing complained, but
this variable already exists in the outer function scope
with the same value (and the SKB isn't changed either.)
Remove the extra one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This got unused when the tracing was converted to dynamic
strings, so the define can be removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are some changes coming to wireless-next that will
otherwise cause conflicts, pull wireless in first to be
able to resolve that when applying the individual changes
rather than having to do merge resolution later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The set_active_links API is intended for link switching, so switching
to no links at all is not supported.
Add a warning to check that.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129200054.e3c113f94508.Ia35f927f914bf98dd8f9350dd4f78b1d901b1c1d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It doesn't make sense to return BSS change flags in an int, as
they're a bigger type. For this particular function it still
works OK, but clean it up to avoid future errors (or copying
this code in a broken way.)
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240129195739.e340a7d5e7c6.I1dfcca32d43dce903494a2c474844491682671b4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Even if there are a lot of possible ways drivers might
call this, at least knowing when they do and with what
settings can be useful. Add tracing for it.
Link: https://msgid.link/20240129195435.b20d2ead2013.I8213e65c274451d523a3397519ac578c3ed2df4d@changeid
[removed link-id contortions as suggested by Jeff]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On the 6 GHz band, probe responses are sent as broadcast to
optimise medium usage. However, without OCE configuration
we weren't accepting them, which is wrong, even if wpa_s is
by default enabling OCE. Accept them without the OCE config
as well.
Link: https://msgid.link/20240129200907.5a89c2821897.I92e9dfa0f9b350bc7f37dd4bb38031d156d78d8a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's a call to drv_mgd_prepare_tx() and so there should
be one to drv_mgd_complete_tx(), but on this path it's not.
Add it.
Link: https://msgid.link/20240131164824.2f0922a514e1.I5aac89b93bcead88c374187d70cad0599d29d2c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This should be waiting if we don't have a beacon yet,
but somehow I managed to invert the logic. Fix that.
Fixes: 74e1309acedc ("wifi: mac80211: mlme: look up beacon elems only if needed")
Link: https://msgid.link/20240131164856.922701229546.I239b379e7cee04608e73c016b737a5245e5b23dd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's a bug in ieee80211_set_unsol_bcast_probe_resp(), it tries
to return BSS_CHANGED_UNSOL_BCAST_PROBE_RESP (which has the value
1<<31) in an int, which makes it negative and considered an error.
Fix this by passing the changed flags to set separately.
Fixes: 3b1c256eb4ae ("wifi: mac80211: fixes in FILS discovery updates")
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240129195729.965b0740bf80.I6bc6f5236863f686c17d689be541b1dd2633c417@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The SMPS mode is currently re-initialized too late, since
ieee80211_prep_channel() can be called again after we've
already done ieee80211_setup_assoc_link(), in case there's
some override of the channel configuration. Fix this.
Link: https://msgid.link/20240129195405.d6d74508be18.I0a7303b1ce4d8e5436011951ab624372a445c069@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a driver implements the change_interface() method, we switch
interface type without taking the interface down, but still will
recreate the debugfs for it since it's a new type. As such, we
should use the ieee80211_debugfs_recreate_netdev() function here
to also recreate the driver's files, if it is indeed from a type
change while up.
Link: https://msgid.link/20240129155402.7311a36ffeeb.I18df02bbeb685d4250911de5ffbaf090f60c3803@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When a station is added/reconfigured by userspace, e.g. a TDLS
peer or a SoftAP client STA, rx_nss is currently not always set,
so that it might be left zero. Set it up properly.
Link: https://msgid.link/20240129155354.98f148a3d654.I193a02155f557ea54dc9d0232da66cf96734119a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This looks up the link under RCU protection, but isn't
guaranteed to actually have protection. Fix that.
Fixes: 8cc07265b691 ("wifi: mac80211: handle TDLS data frames with MLO")
Link: https://msgid.link/20240129155348.8a9c0b1e1d89.I553f96ce953bb41b0b877d592056164dec20d01c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As mentioned in the previous commit, we pretty quickly found
that some APs have ECSA elements stuck in their probe response,
so using that to not attempt to connect while CSA is happening
we never connect to such an AP.
Improve this situation by checking more carefully and ignoring
the ECSA if cfg80211 has previously detected the ECSA element
being stuck in the probe response.
Additionally, allow connecting to an AP that's switching to a
channel it's already using, unless it's using quiet mode. In
this case, we may just have to adjust bandwidth later. If it's
actually switching channels, it's better not to try to connect
in the middle of that.
Reported-by: coldolt <andypalmadi@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/CAJvGw+DQhBk_mHXeu6RTOds5iramMW2FbMB01VbKRA4YbHHDTA@mail.gmail.com/
Fixes: c09c4f31998b ("wifi: mac80211: don't connect to an AP while it's in a CSA process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129131413.cc2d0a26226e.I682c016af76e35b6c47007db50e8554c5a426910@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Due to the way that debugging is used in the mac80211 subsystem
this message ends up being noisier than it needs to be.
As the statement is only useful at a first stage of triage for
BIOS bugs, just drop it.
Cc: Jun Ma <Jun.Ma2@amd.com>
Suggested-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240117030525.539-1-mario.limonciello@amd.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch makes duration in scan request be applicable when using
SW scan, but only accepts durations greater than the default value for
the following reasons:
1. Most APs have a beacoon interval of 100ms.
2. Sending and receiving probe require some delay.
3. Setting channel to HW also requires some delays
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://msgid.link/20240123054752.22833-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This does not change anything effectively, but it is closer to what the
code is trying to achieve here. i.e. select the link data if it is an
MLD and fall back to using the deflink otherwise.
Fixes: 0f99f0878350 ("wifi: mac80211: Print local link address during authentication")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.4c4b1c40eb3c.I2771621dee328c618536596b7e56232df42a79c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When parsing 6 GHz operation, don't set the bss_conf
values. We only commit to that later in association,
so move the code there. Also clear it later.
While at it, handle IEEE80211_6GHZ_CTRL_REG_VLP_AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.c2da4bc515e8.I219ca40e15c0fbaff0e7c3e83ca4b92ecbc1f8ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To simplify the code in the next patch, disallow drivers
supporting 40 MHz in HT but not HE, since we'd otherwise
have to track local maximum bandwidth per mode there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.da15fe3214d2.I4df51ad2f4c844615c168bf9bdb498925b3c77d4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For verifying the required HE capabilities are supported
locally, we access the HE capability element of the AP.
Simplify that access, we've already parsed and validated
it when parsing elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.2ef62b43caeb.I8baa604dd3f3399e08b86c99395a2c6a1185d35d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We already parse all the BSS elements into elems, there's
really no need to separately find EHT/ML again. Remove the
extra code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.c4a55da9f778.I112b1ef00904c4183ac7644800f8daa8a4449875@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The only user of this function passes a lot of pointers
directly from the parsed elements, so it's simpler to
just pass the entire elements parsing struct. This also
shows that the ht_cap is actually unused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.f0653cd5e7dd.I8bd5ee848074029a9f0495c95e4339546ad8fe15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The association response is more likely to be correct
than a random scan result, which really also should be
correct, but we generally prefer to take data from the
association response, so do that here as well.
Also reset the data so it doesn't hang around from an
old connection to a non-MLO connection, drivers would
hopefully not look at it, but less surprise this way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.1d10f1d1dbab.I545e955675e2269a52496a22ae7822d95b40235e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If software crypto is used, simply add support for SPP A-MSDUs
(and use it whenever enabled as required by the cfg80211 API).
If hardware crypto is used, leave it up to the driver to set
the NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT flag and then check
sta->spp_amsdu or the IEEE80211_KEY_FLAG_SPP_AMSDU key flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.b8ada4514e2b.I1ac25d5f158165b5a88062a5a5e4c4fbeecf9a5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Update neg_ttlm and active_links according to the new mapping,
and send a negotiated TID-to-link map request with the new mapping.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.eeb385d771df.I2a5441c14421de884dbd93d1624ce7bb2c944833@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
An MLD may send TID-to-Link mapping request frame to negotiate
TID to link mapping with a peer MLD.
Support handling negotiated TID-to-Link mapping request frame
by parsing the frame, asking the driver whether it supports the
received mapping or not, and sending a TID-to-Link mapping response
to the AP MLD.
Theoretically, links that became inactive due to the received TID-to-Link
mapping request, can be selected to be activated but this would require
tearing down the negotiated TID-to-Link mapping, which is still not
supported.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.0bc1a24fcc9d.Ie72e47dc6f8c77d4a2f0947b775ef6367fe0edac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc2
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
* tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix race condition on enabling fast-xmit
wifi: iwlwifi: fix a memory corruption
wifi: mac80211: fix potential sta-link leak
wifi: cfg80211/mac80211: remove dependency on non-existing option
wifi: cfg80211: fix missing interfaces when dumping
wifi: ath11k: rely on mac80211 debugfs handling for vif
wifi: p54: fix GCC format truncation warning with wiphy->fw_version
====================
Link: https://lore.kernel.org/r/20240122153434.E0254C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240104181059.84032-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When a station is allocated, links are added but not
set to valid yet (e.g. during connection to an AP MLD),
we might remove the station without ever marking links
valid, and leak them. Fix that.
Fixes: cb71f1d136a6 ("wifi: mac80211: add sta link addition/removal")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.6573998beaf8.I09ac2e1d41c80f82a5a616b8bd1d9d8dd709a6a6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit ffbd0c8c1e7f ("wifi: mac80211: add an element parsing unit test")
and commit 730eeb17bbdd ("wifi: cfg80211: add first kunit tests, for
element defrag") add new configs that depend on !KERNEL_6_2, but the config
option KERNEL_6_2 does not exist in the tree. This dependency is used for
handling backporting to restrict the option to certain kernels but this
really should not be carried around the mainline kernel tree.
Clean up this needless dependency on the non-existing option KERNEL_6_2.
Link: https://lore.kernel.org/lkml/CAKXUXMyfrM6amOR7Ysim3WNQ-Ckf9HJDqRhAoYmLXujo1UV+yA@mail.gmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
e009b2efb7a8 ("bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()")
0f2b21477988 ("bnxt_en: Fix compile error without CONFIG_RFS_ACCEL")
https://lore.kernel.org/all/20240105115509.225aa8a2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Just a couple of more things over the holidays:
- first kunit tests for both cfg80211 and mac80211
- a few multi-link fixes
- DSCP mapping update
- RCU fix
* tag 'wireless-next-2024-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next:
wifi: mac80211: remove redundant ML element check
wifi: cfg80211: parse all ML elements in an ML probe response
wifi: cfg80211: correct comment about MLD ID
wifi: cfg80211: Update the default DSCP-to-UP mapping
wifi: cfg80211: tests: add some scanning related tests
wifi: mac80211: kunit: extend MFP tests
wifi: mac80211: kunit: generalize public action test
wifi: mac80211: add kunit tests for public action handling
kunit: add a convenience allocation wrapper for SKBs
kunit: add parameter generation macro using description from array
wifi: mac80211: fix spelling typo in comment
wifi: cfg80211: fix RCU dereference in __cfg80211_bss_update
====================
Link: https://lore.kernel.org/r/20240103144423.52269-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If "ml_basic" is assigned, we already know that the type
of ML element is basic, so we don't need to check again,
that check can never happen. Simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.bb9b636e66f6.I7fc0897022142d46f39ac0b912a4f7b0f1b6ea26@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Extend the MFP tests to handle the case of deauth/disassoc
and robust action frames (that are not protected dual of
public action frames).
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20231220151952.415232-6-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Generalize the test to be able to handle arbitrary
action categories and non-action frames, for further
test expansion.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20231220151952.415232-5-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Check the logic in ieee80211_drop_unencrypted_mgmt()
according to a list of test cases derived from the
spec.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://msgid.link/20231220151952.415232-4-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix spelling of "attributes" in a comment.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Zheng tan <tanzheng@kylinos.cn>
Link: https://msgid.link/20240102015418.3673858-1-tanzheng@kylinos.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The third "new features" pull request for v6.8. This is a smaller one
to clear up our tree before the break and nothing really noteworthy
this time.
Major changes:
stack
* cfg80211: introduce cfg80211_ssid_eq() for SSID matching
* cfg80211: support P2P operation on DFS channels
* mac80211: allow 64-bit radiotap timestamps
iwlwifi
* AX210: allow concurrent P2P operation on DFS channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
