| Age | Commit message (Collapse) | Author |
|---|
|
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d26950 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().
Drop the reference when this unlikely error is hit.
Fixes: 1c30d1836aeb ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.
Fix by removing these warnings for now.
Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.
Fixes: 6e6030bd5412 ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the network stack calls .send_pkt()/.cancel_pkt() during .release(),
a struct vhost_vsock use-after-free is possible. This occurs because
.release() does not wait for other CPUs to stop using struct
vhost_vsock.
Switch to an RCU-enabled hashtable (indexed by guest CID) so that
.release() can wait for other CPUs by calling synchronize_rcu(). This
also eliminates vhost_vsock_lock acquisition in the data path so it
could have a positive effect on performance.
This is CVE-2018-14625 "kernel: use-after-free Read in vhost_transport_send_pkt".
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+bd391451452fb0b93039@syzkaller.appspotmail.com
Reported-by: syzbot+e3e074963495f92a89ed@syzkaller.appspotmail.com
Reported-by: syzbot+d5a0a170c5069658b141@syzkaller.appspotmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
While ccw_io_helper() seems like intended to be exclusive in a sense that
it is supposed to facilitate I/O for at most one thread at any given
time, there is actually nothing ensuring that threads won't pile up at
vcdev->wait_q. If they do, all threads get woken up and see the status
that belongs to some other request than their own. This can lead to bugs.
For an example see:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1788432
This race normally does not cause any problems. The operations provided
by struct virtio_config_ops are usually invoked in a well defined
sequence, normally don't fail, and are normally used quite infrequent
too.
Yet, if some of the these operations are directly triggered via sysfs
attributes, like in the case described by the referenced bug, userspace
is given an opportunity to force races by increasing the frequency of the
given operations.
Let us fix the problem by ensuring, that for each device, we finish
processing the previous request before starting with a new one.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-3-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Currently we have a race on vcdev->config in virtio_ccw_get_config() and
in virtio_ccw_set_config().
This normally does not cause problems, as these are usually infrequent
operations. However, for some devices writing to/reading from the config
space can be triggered through sysfs attributes. For these, userspace can
force the race by increasing the frequency.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-2-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
If a local process has closed a connected socket and hasn't received a
RST packet yet, then the socket remains in the table until a timeout
expires.
When a vhost_vsock instance is released with the timeout still pending,
the socket is never freed because vhost_vsock has already set the
SOCK_DONE flag.
Check if the close timer is pending and let it close the socket. This
prevents the race which can leak sockets.
Reported-by: Maximilian Riemensberger <riemensberger@cadami.net>
Cc: Graham Whaley <graham.whaley@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"This is a single commit that fixes a bug in uprobes SDT code due to a
missing mutex protection"
* tag 'trace-v4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
Uprobes: Fix kernel oops with delayed_uprobe_remove()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Still more incoming fixes than wished at this stage, but all look like
small and reasonable fixes.
In addition to the usual HD-audio and USB-audio quirks for various
devices, two notable changes are included:
- a fix for USB-audio UAF at probing a malformed descriptor
- workarounds for PCM rwsem mutex starvation"
* tag 'sound-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4860G/Z6860G
ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4660G
ALSA: hda/realtek - Add support for Acer Aspire C24-860 headset mic
ALSA: hda/realtek: ALC286 mic and headset-mode fixups for Acer Aspire U27-880
ALSA: usb-audio: Fix UAF decrement if card has no live interfaces in card.c
ALSA: hda/realtek - Fix speaker output regression on Thinkpad T570
ALSA: pcm: Fix interval evaluation with openmin/max
ALSA: hda: Add support for AMD Stoney Ridge
ALSA: usb-audio: Add SMSL D1 to quirks for native DSD support
ALSA: pcm: Fix starvation on down_write_nonblock()
ALSA: pcm: Call snd_pcm_unlink() conditionally at closing
|
|
Pull C-SKY fixes from Guo Ren:
- bugfix for tlb_get_pgd() error
- update MAINTAINERS file for C-SKY drivers
* tag 'csky-4.20-rc6' of github.com:c-sky/csky-linux:
csky: bugfix tlb_get_pgd error.
MAINTAINERS: add maintainer for C-SKY drivers
|
|
Intel Merrifield has a reduced size of FIFO used in iDMA 32-bit controller,
i.e. 512 bytes instead of 1024.
Fix this by partitioning it as 64 bytes per channel.
Note, in the future we might switch to 'fifo-size' property instead of
hard coded value.
Fixes: 199244d69458 ("dmaengine: dw: add support of iDMA 32-bit hardware")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Currently the 'stackleak_cleanup' pass deleting a CALL insn is executed
after the 'reload' pass. That allows gcc to do some weird optimization in
function prologues and epilogues, which are generated later [1].
Let's avoid that by registering the 'stackleak_cleanup' pass before
the '*free_cfg' pass. It's the moment when the stack frame size is
already final, function prologues and epilogues are generated, and the
machine-dependent code transformations are not done.
[1] https://www.openwall.com/lists/kernel-hardening/2018/11/23/2
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fix for v4.20-rc6
Here's a fix for a reported USB-console regression in 4.18 which
revealed a long-standing bug in the console implementation.
The patch has been in linux-next over night with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: console: fix reported terminal settings
|
|
Marek Szyprowski reported problems with CPU hotplug in current kernels.
This was tracked down to the processor vtables being located in an
init section, and therefore discarded after kernel boot, despite being
required after boot to properly initialise the non-boot CPUs.
Arrange for these tables to end up in .rodata when required.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 383fb3ee8024 ("ARM: spectre-v2: per-CPU vtables to work around big.Little systems")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Blocks creating a DEVX UMEM with the non applicable access flags
as of ODP, MW_BIND, etc.
Specifically when an ODP flag is used below WARN call trace is issued.
[ 2510.404131] RIP: 0010:__mlx5_ib_populate_pas+0x207/0x220 [mlx5_ib]
...
[ 2510.404143] Call Trace:
[ 2510.404150] ? __kmalloc_node+0x1b3/0x280
[ 2510.404156] ? _uverbs_alloc+0x63/0x90 [ib_uverbs]
[ 2510.404158] ? _uverbs_alloc+0x63/0x90 [ib_uverbs]
[ 2510.404162] mlx5_ib_populate_pas+0x53/0x60 [mlx5_ib]
[ 2510.404167] mlx5_ib_handler_MLX5_IB_METHOD_DEVX_UMEM_REG+0x273/0x3f0 [mlx5_ib]
Fixes: aeae94579caf ("IB/mlx5: Add DEVX support for memory registration")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Exclude the gnss subsystem from SIRMPRIMA2 regex matching, which would
otherwise match the unrelated gnss sirf driver.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add SCM tree for the gnss subsystem.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Fix activation helper which would return -ETIMEDOUT even if the last
retry attempt was successful.
Also change the semantics of the retries variable so that it actually
holds the number of retries (rather than tries).
Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers")
Cc: stable <stable@vger.kernel.org> # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The broken macros make the glibc compile error. If there is no
__NR3264_fstat*, we should also removed related definitions.
Reported-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Fixes: bf4b6a7d371e ("y2038: Remove stat64 family from default syscall set")
[arnd: Both Marcin and Guo provided this patch to fix up my clearly
broken commit, I applied the version with the better changelog.]
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Signed-off-by: Mao Han <han_mao@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
These interrupt functions are already non-attachable by kprobes.
Blacklist them explicitly so that they can show up in
/sys/kernel/debug/kprobes/blacklist and tools like BCC can use this
additional information.
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lkml.kernel.org/r/20181206095648.GA8249@Dell
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch is trying to fix KE issue due to
"BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198"
reported by Syzkaller scan."
[26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198
[26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364
[26364:syz-executor0][name:report&]
[26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0
[26364:syz-executor0]Call trace:
[26364:syz-executor0][<ffffff9008095cf8>] dump_bacIctrace+Ox0/0x470
[26364:syz-executor0][<ffffff9008096de0>] show_stack+0x20/0x30
[26364:syz-executor0][<ffffff90089cc9c8>] dump_stack+Oxd8/0x128
[26364:syz-executor0][<ffffff90084edb38>] print_address_description +0x80/0x4a8
[26364:syz-executor0][<ffffff90084ee270>] kasan_report+Ox178/0x390
[26364:syz-executor0][<ffffff90084ee4a0>] _asan_report_loadi_noabort+Ox18/0x20
[26364:syz-executor0][<ffffff9008b092ac>] param_set_kgdboc_var+Ox194/0x198
[26364:syz-executor0][<ffffff900813af64>] param_attr_store+Ox14c/0x270
[26364:syz-executor0][<ffffff90081394c8>] module_attr_store+0x60/0x90
[26364:syz-executor0][<ffffff90086690c0>] sysfs_kl_write+Ox100/0x158
[26364:syz-executor0][<ffffff9008666d84>] kernfs_fop_write+0x27c/0x3a8
[26364:syz-executor0][<ffffff9008508264>] do_loop_readv_writev+0x114/0x1b0
[26364:syz-executor0][<ffffff9008509ac8>] do_readv_writev+0x4f8/0x5e0
[26364:syz-executor0][<ffffff9008509ce4>] vfs_writev+0x7c/Oxb8
[26364:syz-executor0][<ffffff900850ba64>] SyS_writev+Oxcc/0x208
[26364:syz-executor0][<ffffff90080883f0>] elO_svc_naked +0x24/0x28
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]The buggy address belongs to the variable:
[26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]Memory state around the buggy address:
[26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
[26364:syz-executor0][name:report&] ^
[26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
[26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint
[26364:syz-executor0]------------[cut here]------------
After checking the source code, we've found there might be an out-of-bounds
access to "config[len - 1]" array when the variable "len" is zero.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There was no bug here, but there was no test coverage for this scenario.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
|
|
xa_mk_value() only handles values up to LONG_MAX. I successfully hid
that inside xa_store_index() and xa_erase_index(), but it turned out I
also needed it for testing xa_alloc() on 32-bit machines. So extract
xa_mk_index() from the above two functions, and convert the non-constant
users of xa_mk_value() to xa_mk_index().
Signed-off-by: Matthew Wilcox <willy@infradead.org>
|
|
These convenience wrappers match the other _irq and _bh wrappers we
already have. It turns out I'd already open-coded xa_cmpxchg_irq()
in the shmem code, so convert that.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
|
|
Commit 66ee620f06f9 ("idr: Permit any valid kernel pointer to be stored")
changed the radix tree lookup so that it stops when reaching the bottom
of the tree. However, the condition was added in the wrong place,
making it possible to return retry entries to the caller. Reorder the
tests to check for the retry entry before checking whether we're at the
bottom of the tree. The retry entry should never be found in the tree
root, so it's safe to defer the check until the end of the loop.
Add a regression test to the test-suite to be sure this doesn't come
back.
Fixes: 66ee620f06f9 ("idr: Permit any valid kernel pointer to be stored")
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
|
|
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We observed some premature timeouts on a virtualization platform, the log
is like this:
case 1:
[159525.255629] mmc1: Internal clock never stabilised.
[159525.255818] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[159525.256049] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001002
...
[159525.257205] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
From the clock control register dump, we are pretty sure the clock was
stablized.
case 2:
[ 914.550127] mmc1: Reset 0x2 never completed.
[ 914.550321] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 914.550608] mmc1: sdhci: Sys addr: 0x00000010 | Version: 0x00001002
After checking the sdhci code, we found the timeout check actually has a
little window that the CPU can be scheduled out and when it comes back,
the original time set or check is not valid.
Fixes: 5a436cc0af62 ("mmc: sdhci: Optimize delay loops")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Make sure to use the CIFS_DIR_SEP(cifs_sb) as path separator for
prefixpath too. Fixes a bug with smb1 UNIX extensions.
Fixes: a6b5058fafdf ("fs/cifs: make share unaccessible at root level mountable")
Signed-off-by: Paulo Alcantara <palcantara@suse.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
|
|
Missing a dependency. Shouldn't show cifs posix extensions
in Kconfig if CONFIG_CIFS_ALLOW_INSECURE_DIALECTS (ie SMB1
protocol) is disabled.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
According to bindings/regulator/fixed-regulator.txt the 'clocks' and
'clock-names' properties are not valid ones.
In order to turn on the Wifi clock the correct location for describing
the CLKO2 clock is via a mmc-pwrseq handle, so do it accordingly.
Fixes: 56354959cfec ("ARM: dts: imx: add Boundary Devices Nitrogen7 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In commit 5e9dcb6188a4 ("powerpc/boot: Expose Kconfig symbols to
wrapper") we added a dependency to serial.c on autoconf.h:
$(obj)/serial.c: $(obj)/autoconf.h
This works when building in-tree (ie. with KBUILD_OUTPUT unset)
because the obj tree is the src tree.
But when building with eg. O=build and -j 1 the build fails:
gcc ... -I../arch/powerpc/boot -c -o arch/powerpc/boot/serial.o arch/powerpc/boot/serial.c
gcc: error: arch/powerpc/boot/serial.c: No such file or directory
Why this is only happening with -j 1 is not clear, when building with
-j greater than 1 somehow we decide to look for serial.c in the src
tree (../), eg:
gcc -I../arch/powerpc/boot -c -o arch/powerpc/boot/serial.o ../arch/powerpc/boot/serial.c
Regardless we shouldn't be specifying a dependency on serial.c in the
build tree, we want to add a dependency to the version in $(srctree)
so fix the rule to say that.
Fixes: 5e9dcb6188a4 ("powerpc/boot: Expose Kconfig symbols to wrapper")
Tested-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The *_frag_reasm() functions are susceptible to miscalculating the byte
count of packet fragments in case the truesize of a head buffer changes.
The truesize member may be changed by the call to skb_unclone(), leaving
the fragment memory limit counter unbalanced even if all fragments are
processed. This miscalculation goes unnoticed as long as the network
namespace which holds the counter is not destroyed.
Should an attempt be made to destroy a network namespace that holds an
unbalanced fragment memory limit counter the cleanup of the namespace
never finishes. The thread handling the cleanup gets stuck in
inet_frags_exit_net() waiting for the percpu counter to reach zero. The
thread is usually in running state with a stacktrace similar to:
PID: 1073 TASK: ffff880626711440 CPU: 1 COMMAND: "kworker/u48:4"
#5 [ffff880621563d48] _raw_spin_lock at ffffffff815f5480
#6 [ffff880621563d48] inet_evict_bucket at ffffffff8158020b
#7 [ffff880621563d80] inet_frags_exit_net at ffffffff8158051c
#8 [ffff880621563db0] ops_exit_list at ffffffff814f5856
#9 [ffff880621563dd8] cleanup_net at ffffffff814f67c0
#10 [ffff880621563e38] process_one_work at ffffffff81096f14
It is not possible to create new network namespaces, and processes
that call unshare() end up being stuck in uninterruptible sleep state
waiting to acquire the net_mutex.
The bug was observed in the IPv6 netfilter code by Per Sundstrom.
I thank him for his analysis of the problem. The parts of this patch
that apply to IPv4 and IPv6 fragment reassembly are preemptive measures.
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Reported-by: Per Sundstrom <per.sundstrom@redqube.se>
Acked-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If for some reason an association's fragmentation point is zero,
sctp_datamsg_from_user will try to endlessly try to divide a message
into zero-sized chunks. This eventually causes kernel panic due to
running out of memory.
Although this situation is quite unlikely, it has occurred before as
reported. I propose to add this simple last-ditch sanity check due to
the severity of the potential consequences.
Signed-off-by: Jakub Audykowicz <jakub.audykowicz@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When unloading the ast driver, a warning message is printed by
drm_mode_config_cleanup() because a reference is still held to one of
the drm_connector structs.
Correct this by calling drm_crtc_force_disable_all() in
ast_fbdev_destroy().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e613f3c630c7bbc72e04a44b178259b9164d2f6.1543798395.git.sbobroff@linux.ibm.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
UAPI:
- Distinguish lease events from hotplug (Daniel)
Other:
- omap: Restore panel-dpi bus flags (Tomi)
- omap: Fix a couple of dsi issues (Sebastian)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205201428.GA35447@art_vandelay
|
|
into drm-fixes
Fixes for 4.20:
- Fix banding regression on 6 bpc panels
- Vega20 fix for six 4k displays
- Fix LRU handling in ttm_buffer_object_transfer
- Use proper MC firmware for newer polaris variants
- Vega20 powerplay fixes
- VCN suspend/resume fix for PCO
- Misc other fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205192934.2857-1-alexander.deucher@amd.com
|
|
https://gitlab.freedesktop.org/seanpaul/dpu-staging into drm-fixes
- Several related to incorrect error checking/handling (Various)
- Prevent IRQ storm on MDP5 HDMI hotplug (Todor)
- Don't capture crash state if unsupported (Sharat)
- Properly grab vblank reference in atomic wait for commit done (Sean)
Cc: Sharat Masetty <smasetty@codeaurora.org>
Cc: Todor Tomov <todor.tomov@linaro.org>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205194207.GY154160@art_vandelay
|
|
There could be a race between task exit and probe unregister:
exit_mm()
mmput()
__mmput() uprobe_unregister()
uprobe_clear_state() put_uprobe()
delayed_uprobe_remove() delayed_uprobe_remove()
put_uprobe() is calling delayed_uprobe_remove() without taking
delayed_uprobe_lock and thus the race sometimes results in a
kernel crash. Fix this by taking delayed_uprobe_lock before
calling delayed_uprobe_remove() from put_uprobe().
Detailed crash log can be found at:
Link: http://lkml.kernel.org/r/000000000000140c370577db5ece@google.com
Link: http://lkml.kernel.org/r/20181205033423.26242-1-ravi.bangoria@linux.ibm.com
Acked-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reported-by: syzbot+cb1fb754b771caca0a88@syzkaller.appspotmail.com
Fixes: 1cc33161a83d ("uprobes: Support SDT markers having reference count (semaphore)")
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Function graph tracing recurses into itself when stackleak is enabled,
causing the ftrace graph selftest to run for up to 90 seconds and
trigger the softlockup watchdog.
Breakpoint 2, ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:200
200 mcount_get_lr_addr x0 // pointer to function's saved lr
(gdb) bt
\#0 ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:200
\#1 0xffffff80081d5280 in ftrace_caller () at ../arch/arm64/kernel/entry-ftrace.S:153
\#2 0xffffff8008555484 in stackleak_track_stack () at ../kernel/stackleak.c:106
\#3 0xffffff8008421ff8 in ftrace_ops_test (ops=0xffffff8009eaa840 <graph_ops>, ip=18446743524091297036, regs=<optimized out>) at ../kernel/trace/ftrace.c:1507
\#4 0xffffff8008428770 in __ftrace_ops_list_func (regs=<optimized out>, ignored=<optimized out>, parent_ip=<optimized out>, ip=<optimized out>) at ../kernel/trace/ftrace.c:6286
\#5 ftrace_ops_no_ops (ip=18446743524091297036, parent_ip=18446743524091242824) at ../kernel/trace/ftrace.c:6321
\#6 0xffffff80081d5280 in ftrace_caller () at ../arch/arm64/kernel/entry-ftrace.S:153
\#7 0xffffff800832fd10 in irq_find_mapping (domain=0xffffffc03fc4bc80, hwirq=27) at ../kernel/irq/irqdomain.c:876
\#8 0xffffff800832294c in __handle_domain_irq (domain=0xffffffc03fc4bc80, hwirq=27, lookup=true, regs=0xffffff800814b840) at ../kernel/irq/irqdesc.c:650
\#9 0xffffff80081d52b4 in ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:205
Rework so we mark stackleak_track_stack as notrace
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The sw2iso count should cover ARM LDO ramp-up time,
the MAX ARM LDO ramp-up time may be up to more than
100us on some boards, this patch sets sw2iso to 0xf
(~384us) which is the reset value, and it is much
more safe to cover different boards, since we have
observed that some customer boards failed with current
setting of 0x2.
Fixes: 05136f0897b5 ("ARM: imx: support arm power off in cpuidle for i.mx6sx")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four obvious bug fixes. The vmw_pscsi is so old that it's amazing
no-one noticed before now"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: storvsc: Fix a race in sub-channel creation that can cause panic
scsi: vmw_pscsi: Rearrange code to avoid multiple calls to free_irq during unload
scsi: libiscsi: Fix NULL pointer dereference in iscsi_eh_session_reset
scsi: lpfc: fix block guard enablement on SLI3 adapters
|
|
TCP loss probe timer may fire when the retranmission queue is empty but
has a non-zero tp->packets_out counter. tcp_send_loss_probe will call
tcp_rearm_rto which triggers NULL pointer reference by fetching the
retranmission queue head in its sub-routines.
Add a more detailed warning to help catch the root cause of the inflight
accounting inconsistency.
Reported-by: Rafael Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If available rwnd is too small, tcp_tso_should_defer()
can decide it is worth waiting before splitting a TSO packet.
This really means we are rwnd limited.
Fixes: 5615f88614a4 ("tcp: instrument how long TCP is limited by receive window")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2018-12-05
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix bpf uapi pointers for 32-bit architectures, from Daniel.
2) improve verifer ability to handle progs with a lot of branches, from Alexei.
3) strict btf checks, from Yonghong.
4) bpf_sk_lookup api cleanup, from Joe.
5) other misc fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
list_del() leaves the skb->next pointer poisoned, which can then lead to
a crash in e.g. OVS forwarding. For example, setting up an OVS VXLAN
forwarding bridge on sfc as per:
========
$ ovs-vsctl show
5dfd9c47-f04b-4aaa-aa96-4fbb0a522a30
Bridge "br0"
Port "br0"
Interface "br0"
type: internal
Port "enp6s0f0"
Interface "enp6s0f0"
Port "vxlan0"
Interface "vxlan0"
type: vxlan
options: {key="1", local_ip="10.0.0.5", remote_ip="10.0.0.4"}
ovs_version: "2.5.0"
========
(where 10.0.0.5 is an address on enp6s0f1)
and sending traffic across it will lead to the following panic:
========
general protection fault: 0000 [#1] SMP PTI
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 4.20.0-rc3-ehc+ #701
Hardware name: Dell Inc. PowerEdge R710/0M233H, BIOS 6.4.0 07/23/2013
RIP: 0010:dev_hard_start_xmit+0x38/0x200
Code: 53 48 89 fb 48 83 ec 20 48 85 ff 48 89 54 24 08 48 89 4c 24 18 0f 84 ab 01 00 00 48 8d 86 90 00 00 00 48 89 f5 48 89 44 24 10 <4c> 8b 33 48 c7 03 00 00 00 00 48 8b 05 c7 d1 b3 00 4d 85 f6 0f 95
RSP: 0018:ffff888627b437e0 EFLAGS: 00010202
RAX: 0000000000000000 RBX: dead000000000100 RCX: ffff88862279c000
RDX: ffff888614a342c0 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff888618a88000 R08: 0000000000000001 R09: 00000000000003e8
R10: 0000000000000000 R11: ffff888614a34140 R12: 0000000000000000
R13: 0000000000000062 R14: dead000000000100 R15: ffff888616430000
FS: 0000000000000000(0000) GS:ffff888627b40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f6d2bc6d000 CR3: 000000000200a000 CR4: 00000000000006e0
Call Trace:
<IRQ>
__dev_queue_xmit+0x623/0x870
? masked_flow_lookup+0xf7/0x220 [openvswitch]
? ep_poll_callback+0x101/0x310
do_execute_actions+0xaba/0xaf0 [openvswitch]
? __wake_up_common+0x8a/0x150
? __wake_up_common_lock+0x87/0xc0
? queue_userspace_packet+0x31c/0x5b0 [openvswitch]
ovs_execute_actions+0x47/0x120 [openvswitch]
ovs_dp_process_packet+0x7d/0x110 [openvswitch]
ovs_vport_receive+0x6e/0xd0 [openvswitch]
? dst_alloc+0x64/0x90
? rt_dst_alloc+0x50/0xd0
? ip_route_input_slow+0x19a/0x9a0
? __udp_enqueue_schedule_skb+0x198/0x1b0
? __udp4_lib_rcv+0x856/0xa30
? __udp4_lib_rcv+0x856/0xa30
? cpumask_next_and+0x19/0x20
? find_busiest_group+0x12d/0xcd0
netdev_frame_hook+0xce/0x150 [openvswitch]
__netif_receive_skb_core+0x205/0xae0
__netif_receive_skb_list_core+0x11e/0x220
netif_receive_skb_list+0x203/0x460
? __efx_rx_packet+0x335/0x5e0 [sfc]
efx_poll+0x182/0x320 [sfc]
net_rx_action+0x294/0x3c0
__do_softirq+0xca/0x297
irq_exit+0xa6/0xb0
do_IRQ+0x54/0xd0
common_interrupt+0xf/0xf
</IRQ>
========
So, in all listified-receive handling, instead pull skbs off the lists with
skb_list_del_init().
Fixes: 9af86f933894 ("net: core: fix use-after-free in __netif_receive_skb_list_core")
Fixes: 7da517a3bc52 ("net: core: Another step of skb receive list processing")
Fixes: a4ca8b7df73c ("net: ipv4: fix drop handling in ip_list_rcv() and ip_list_rcv_finish()")
Fixes: d8269e2cbf90 ("net: ipv6: listify ipv6_rcv() and ip6_rcv_finish()")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes/updates from Vineet Gupta
- Missing reads{x}()/writes{x}() getting in the way of some drivers [Jose Abreu]
- Builds defaulting to ARCv2 ISA based configsa [Kevin Hilman]
- Misc fixes
* tag 'arc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: io.h: Implement reads{x}()/writes{x}()
ARC: change defconfig defaults to ARCv2
arc: [devboards] Add support of NFSv3 ACL
ARC: mm: fix uninitialised signal code in do_page_fault
ARC: [plat-hsdk] Enable DW APB GPIO support
ARCv2: boot log unaligned access in use
ARC: IOC: panic if kernel was started with previously enabled IOC
ARC: remove redundant 'default n' from Kconfig
|
|
This is a full revert of ac5b2c18911f ("mm: thp: relax __GFP_THISNODE for
MADV_HUGEPAGE mappings") and a partial revert of 89c83fb539f9 ("mm, thp:
consolidate THP gfp handling into alloc_hugepage_direct_gfpmask").
By not setting __GFP_THISNODE, applications can allocate remote hugepages
when the local node is fragmented or low on memory when either the thp
defrag setting is "always" or the vma has been madvised with
MADV_HUGEPAGE.
Remote access to hugepages often has much higher latency than local pages
of the native page size. On Haswell, ac5b2c18911f was shown to have a
13.9% access regression after this commit for binaries that remap their
text segment to be backed by transparent hugepages.
The intent of ac5b2c18911f is to address an issue where a local node is
low on memory or fragmented such that a hugepage cannot be allocated. In
every scenario where this was described as a fix, there is abundant and
unfragmented remote memory available to allocate from, even with a greater
access latency.
If remote memory is also low or fragmented, not setting __GFP_THISNODE was
also measured on Haswell to have a 40% regression in allocation latency.
Restore __GFP_THISNODE for thp allocations.
Fixes: ac5b2c18911f ("mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings")
Fixes: 89c83fb539f9 ("mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask")
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A "short" ARS (address range scrub) instructs the platform firmware to
return known errors. In contrast, a "long" ARS instructs platform
firmware to arrange every data address on the DIMM to be read / checked
for poisoned data.
The conversion of the flags in commit d3abaf43bab8 "acpi, nfit: Fix
Address Range Scrub completion tracking", changed the meaning of passing
'0' to acpi_nfit_ars_rescan(). Previously '0' meant "not short", now '0'
is ARS_REQ_SHORT. Pass ARS_REQ_LONG to restore the expected scrub-type
behavior of user-initiated ARS sessions.
Fixes: d3abaf43bab8 ("acpi, nfit: Fix Address Range Scrub completion tracking")
Reported-by: Jacek Zloch <jacek.zloch@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
