| Age | Commit message (Collapse) | Author |
|---|
|
Commit cfe30b872058 "libnvdimm, pmem: adjust for section collisions with
'System RAM'" enabled Linux to workaround occasions where platform
firmware arranges for "System RAM" and "Persistent Memory" to collide
within a single section boundary. Unfortunately, as reported in this
issue [1], platform firmware can inflict the same collision between
persistent memory regions.
The approach of interrogating iomem_resource does not work in this
case because platform firmware may merge multiple regions into a single
iomem_resource range. Instead provide a method to interrogate regions
that share the same parent bus.
This is a stop-gap until the core-MM can grow support for hotplug on
sub-section boundaries.
[1]: https://github.com/pmem/ndctl/issues/76
Fixes: cfe30b872058 ("libnvdimm, pmem: adjust for section collisions with...")
Cc: <stable@vger.kernel.org>
Reported-by: Patrick Geary <patrickg@supermicro.com>
Tested-by: Patrick Geary <patrickg@supermicro.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In preparation for libnvdimm growing new restrictions to detect section
conflicts between persistent memory regions, enable nfit_test to
allocate aligned resources. Use a gen_pool to allocate nfit_test's fake
resources in a separate address space from the virtual translation of
the same.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull block fixes from Jens Axboe:
"A bit earlier in the week as usual, but there's a fix here that should
go in sooner rather than later.
Under a combination of circumstance, the direct issue path in blk-mq
could corrupt data. This wasn't easy to hit, but the ones that are
affected by it, seem to hit it pretty easily. Full explanation in the
patch. None of the regular filesystem and storage testing has
triggered it, even though it's been around since 4.19-rc1.
Outside of that, whitelist trim tweak for certain Samsung devices for
libata"
* tag 'for-linus-20181205' of git://git.kernel.dk/linux-block:
blk-mq: fix corruption with direct issue
libata: whitelist all SAMSUNG MZ7KM* solid-state disks
|
|
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg:
====================
As it's been a while, we have various fixes for
* hwsim
* AP mode (client powersave related)
* CSA/FTM interaction
* a busy loop in IE handling
* and similar
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace vcn_v1_0_stop with vcn_v1_0_set_powergating_state during suspend,
to keep adev->vcn.cur_state update. It will fix VCN S3 hung issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The Request API is now merged to the kernel but the confidence on the
stability of that API is not great, especially regarding the interaction
with V4L2.
Add a Kconfig option for the API, with a scary-looking warning.
The patch itself disables request creation as well as does not advertise
them as buffer flags. The driver requiring requests (cedrus) now depends
on the Kconfig option as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add a note mentioning that these two controls are not part of the
public API while they still stabilizing.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The MPEG2 state controls for the cedrus stateless MPEG2 driver are
not yet stable. Move them out of the public headers into media/mpeg2-ctrls.h.
Eventually, once this has stabilized, they will be moved back to the
public headers.
Unfortunately I had to cast the control type to a u32 in two switch
statements to prevent a compiler warning about a control type define
not being part of the enum.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"A patch in 4.19 introduced a sanity check that was too strict and a
filesystem cannot be mounted.
This happens for filesystems with more than 10 devices and has been
reported by a few users so we need the fix to propagate to stable"
* tag 'for-4.20-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: tree-checker: Don't check max block group size as current max chunk size limit is unreliable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Revert a problematic recent commit that attempted to fix a system-wide
suspend issue related to the freezer"
* tag 'pm-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "exec: make de_thread() freezable"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd bugfix from Lee Jones:
"Replace release function in cros_ec_dev"
* tag 'mfd-fixes-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
Revert "mfd: cros_ec: Use devm_kzalloc for private data"
|
|
Acer AIO Veriton Z4860G/Z6860G with the same ALC286 codec has issues
with the input from external microphone. The issue can be fixed by
the fixup ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE for Veriton Z4660G.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Acer AIO Veriton Z4660G with ALC286 codec has issue with the input
from external microphones connecting via 'Front Mic' jack. The fixup
ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE enables the jack sensing of
the headset and fix the audio input issue of external microphone.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Acer AIO Aspire C24-860 with ALC286 can't detect the headset
microphone. Just like another Acer AIO U27-880, it needs a different
pin value for 0x18 and the headset fixup to make headset mic work.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Acer Aspire U27-880(AIO) with ALC286 codec can not detect headset mic
and internal mic not working either. It needs the similar quirk like
Sony laptops to fix headphone jack sensing and enables use of the
internal microphone.
Unfortunately jack sensing for the headset mic is still not working.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of devm_thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
drm-intel-fixes
gvt-fixes-2018-12-04
- Fix tiling mode format on BDW for VFIO gfx dmabuf (Tina)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204050633.GY12743@zhen-hp.sh.intel.com
|
|
If the connection is broken, then xs_tcp_state_change() will take care
of scheduling the socket close as soon as appropriate. xs_read_stream()
just needs to report the error.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
Ensure that we do not exit the socket read callback without clearing
XPRT_SOCK_DATA_READY.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
When discarding message data from the stream, we're better off using
the discard iterator, since that will work with non-TCP streams.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
If the allocator fails before it has reached the target number of pages,
then we need to recheck that we're not seeking past the page buffer.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
The RPC code is occasionally hanging when the receive code fails to
empty the socket buffer due to a partial read of the data. When we
convert that to an EAGAIN, it appears we occasionally leave data in the
socket. The fix is to just keep reading until the socket returns
EAGAIN/EWOULDBLOCK.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Cristian Marussi <cristian.marussi@arm.com>
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
|
|
Commit 7d33c3581536 ("mmc: sdhci-omap: Workaround for Errata i802")
disabled DCRC interrupts during tuning. This write to the interrupt
enable register gets overwritten in sdhci_prepare_data() and the
interrupt is not in fact disabled. Fix this by disabling the interrupt
in the host->ier variable.
Fixes: 7d33c3581536 ("mmc: sdhci-omap: Workaround for Errata i802")
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This function was modified to support the information element extension
case (WLAN_EID_EXTENSION) in a manner that would result in an infinite
loop when going through set of IEs that include WLAN_EID_RIC_DATA and
contain an IE that is in the after_ric array. The only place where this
can currently happen is in mac80211 ieee80211_send_assoc() where
ieee80211_ie_split_ric() is called with after_ric[].
This can be triggered by valid data from user space nl80211
association/connect request (i.e., requiring GENL_UNS_ADMIN_PERM). The
only known application having an option to include WLAN_EID_RIC_DATA in
these requests is wpa_supplicant and it had a bug that prevented this
specific contents from being used (and because of that, not triggering
this kernel bug in an automated test case ap_ft_ric) and now that this
bug is fixed, it has a workaround to avoid this kernel issue.
WLAN_EID_RIC_DATA is currently used only for testing purposes, so this
does not cause significant harm for production use cases.
Fixes: 2512b1b18d07 ("mac80211: extend ieee80211_ie_split to support EXTENSION")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We stopped re-applying the GT workarounds after engine reset since commit
59b449d5c82a ("drm/i915: Split out functions for different kinds of
workarounds").
Issue with this is that some of the GT workarounds live in the MMIO space
which gets lost during engine resets. So far the registers in 0x2xxx and
0xbxxx address range have been identified to be affected.
This losing of applied workarounds has obvious negative effects and can
even lead to hard system hangs (see the linked Bugzilla).
Rather than just restoring this re-application, because we have also
observed that it is not safe to just re-write all GT workarounds after
engine resets (GPU might be live and weird hardware states can happen),
we introduce a new class of per-engine workarounds and move only the
affected GT workarounds over.
Using the framework introduced in the previous patch, we therefore after
engine reset, re-apply only the workarounds living in the affected MMIO
address ranges.
v2:
* Move Wa_1406609255:icl to engine workarounds as well.
* Rename API. (Chris Wilson)
* Drop redundant IS_KABYLAKE. (Chris Wilson)
* Re-order engine wa/ init so latest platforms are first. (Rodrigo Vivi)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugzilla.freedesktop.org/show_bug.cgi?id=107945
Fixes: 59b449d5c82a ("drm/i915: Split out functions for different kinds of workarounds")
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133341.10258-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 4a15c75c42460252a63d30f03b4766a52945fb47)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
To enable later verification of GT workaround state at various stages of
driver lifetime, we record the list of applicable ones per platforms to a
list, from which they are also applied.
The added data structure is a simple array of register, mask and value
items, which is allocated on demand as workarounds are added to the list.
This is a temporary implementation which later in the series gets fused
with the existing per context workaround list handling. It is separated at
this stage since the following patch fixes a bug which needs to be as easy
to backport as possible.
Also, since in the following patch we will be adding a new class of
workarounds (per engine) which can be applied from interrupt context, we
straight away make the provision for safe read-modify-write cycle.
v2:
* Change dev_priv to i915 along the init path. (Chris Wilson)
* API rename. (Chris Wilson)
v3:
* Remove explicit list size tracking in favour of growing the allocation
in power of two chunks. (Chris Wilson)
v4:
Chris Wilson:
* Change wa_list_finish to early return.
* Copy workarounds using the compiler for static checking.
* Do not bother zeroing unused entries.
* Re-order struct i915_wa_list.
v5:
* kmalloc_array.
* Whitespace cleanup.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133319.10174-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 25d140faaa25f728159eb8c304eae53d88a7f14e)
Fixes: 59b449d5c82a ("drm/i915: Split out functions for different kinds of workarounds")
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
NullFunc packets should never be duplicate just like
QoS-NullFunc packets.
We saw a client that enters / exits power save with
NullFunc frames (and not with QoS-NullFunc) despite the
fact that the association supports HT.
This specific client also re-uses a non-zero sequence number
for different NullFunc frames.
At some point, the client had to send a retransmission of
the NullFunc frame and we dropped it, leading to a
misalignment in the power save state.
Fix this by never consider a NullFunc frame as duplicate,
just like we do for QoS NullFunc frames.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201449
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the buffered broadcast queue contains packets, letting new packets bypass
that queue can lead to heavy reordering, since the driver is probably throttling
transmission of buffered multicast packets after beacons.
Keep buffering packets until the buffer has been cleared (and no client
is in powersave mode).
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make it behave like regular ieee80211_tx_status calls, except for the lack of
filtered frame processing.
This fixes spurious low-ack triggered disconnections with powersave clients
connected to an AP.
Fixes: f027c2aca0cf4 ("mac80211: add ieee80211_tx_status_noskb")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a255a ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This reverts commit 3aa2177e47878f7e7616da8a2050c44f22301b6e.
That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.
Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.
------------[ cut here ]------------
Device 'cros_ec' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 3 PID: 3675 at drivers/base/core.c:895 device_release+0x80/0x90
Modules linked in: btusb btrtl btintel btbcm bluetooth ...
CPU: 3 PID: 3675 Comm: rmmod Not tainted 4.20.0-rc4 #76
Hardware name: Google Kevin (DT)
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : device_release+0x80/0x90
lr : device_release+0x80/0x90
sp : ffff00000c47bc70
x29: ffff00000c47bc70 x28: ffff8000e86b0d40
x27: 0000000000000000 x26: 0000000000000000
x25: 0000000056000000 x24: 0000000000000015
x23: ffff8000f0bbf860 x22: ffff000000d320a0
x21: ffff8000ee93e100 x20: ffff8000ed931428
x19: ffff8000ed931418 x18: 0000000000000020
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000400 x14: 0000000000000143
x13: 0000000000000000 x12: 0000000000000400
x11: 0000000000000157 x10: 0000000000000960
x9 : ffff00000c47b9b0 x8 : ffff8000e86b1700
x7 : 0000000000000000 x6 : ffff8000f7d520b8
x5 : ffff8000f7d520b8 x4 : 0000000000000000
x3 : ffff8000f7d58e68 x2 : ffff8000e86b0d40
x1 : 37d859939c964800 x0 : 0000000000000000
Call trace:
device_release+0x80/0x90
kobject_put+0x74/0xe8
device_unregister+0x20/0x30
ec_device_remove+0x34/0x48 [cros_ec_dev]
platform_drv_remove+0x28/0x48
device_release_driver_internal+0x1a8/0x240
driver_detach+0x40/0x80
bus_remove_driver+0x54/0xa8
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
cros_ec_dev_exit+0x1c/0x2d8 [cros_ec_dev]
__arm64_sys_delete_module+0x16c/0x1f8
el0_svc_common+0x84/0xd8
el0_svc_handler+0x2c/0x80
el0_svc+0x8/0xc
---[ end trace a57c4625f3c60ae8 ]---
Cc: stable@vger.kernel.org
Fixes: 3aa2177e4787 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Syzbot and KASAN found the following invalid-free bug in
port_over_current_notify():
--------------------------------------------------------------------------
BUG: KASAN: double-free or invalid-free in port_over_current_notify
drivers/usb/core/hub.c:5192 [inline]
BUG: KASAN: double-free or invalid-free in port_event
drivers/usb/core/hub.c:5241 [inline]
BUG: KASAN: double-free or invalid-free in hub_event+0xd97/0x4140
drivers/usb/core/hub.c:5384
CPU: 1 PID: 32710 Comm: kworker/1:3 Not tainted 4.20.0-rc3+ #129
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_invalid_free+0x64/0xa0 mm/kasan/report.c:336
__kasan_slab_free+0x13a/0x150 mm/kasan/kasan.c:501
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3817
port_over_current_notify drivers/usb/core/hub.c:5192 [inline]
port_event drivers/usb/core/hub.c:5241 [inline]
hub_event+0xd97/0x4140 drivers/usb/core/hub.c:5384
process_one_work+0xc90/0x1c40 kernel/workqueue.c:2153
worker_thread+0x17f/0x1390 kernel/workqueue.c:2296
kthread+0x35a/0x440 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
--------------------------------------------------------------------------
The problem is caused by use of a static array to store
environment-string pointers. When the routine is called by multiple
threads concurrently, the pointers from one thread can overwrite those
from another.
The solution is to use an ordinary automatic array instead of a static
array.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+98881958e1410ec7e53c@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
off-by-one mistake in core/rtw_mlme_ext.c"
pstapriv->max_num_sta is always <= NUM_STA, since max_num_sta is either
set in _rtw_init_sta_priv() or rtw_set_beacon().
Fixes: ef9209b642f1 ("staging: rtl8723bs: Fix indenting errors and an off-by-one mistake in core/rtw_mlme_ext.c")
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit 8b7a13c3f404 ("staging: r8712u: Fix possible buffer
overrun") we fix a potential off by one by making the limit smaller.
The better fix is to make the buffer larger. This makes it match up
with the similar code in other drivers.
Fixes: 8b7a13c3f404 ("staging: r8712u: Fix possible buffer overrun")
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver defines three states for a cppi channel.
- idle: .chan_busy == 0 && not in .pending list
- pending: .chan_busy == 0 && in .pending list
- busy: .chan_busy == 1 && not in .pending list
There are cases in which the cppi channel could be in the pending state
when cppi41_dma_issue_pending() is called after cppi41_runtime_suspend()
is called.
cppi41_stop_chan() has a bug for these cases to set channels to idle state.
It only checks the .chan_busy flag, but not the .pending list, then later
when cppi41_runtime_resume() is called the channels in .pending list will
be transitioned to busy state.
Removing channels from the .pending list solves the problem.
Fixes: 975faaeb9985 ("dma: cppi41: start tear down only if channel is busy")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Bin Liu <b-liu@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This reverts commit 8ed46368776b3bc93d74c1f8f2bfb9fd8a9ad805.
This commit breaks boot on Armada 8K based systems. Reverting it makes
affected systems boot again.
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
DMA buffer descriptors aren't allocated from atomic context, so they
can use the less heavyweigth GFP_NOWAIT.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The dmaengine documentation states that device_terminate_all may be
asynchronous and need not wait for the active transfers to stop.
This allows us to move most of the functionality currently implemented
in the sdma channel termination function to run in a worker, outside
of any atomic context. Moving this out of atomic context has two
benefits: we can now sleep while waiting for the channel to terminate,
instead of busy waiting and the freeing of the dma descriptors happens
with IRQs enabled, getting rid of a warning in the dma mapping code.
As the termination is now async, we need to implement the
device_synchronize dma engine function which simply waits for the
worker to finish its execution.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This reverts commit fe5b85c656bc. The SDMA engine needs the descriptors to
be contiguous in memory. As the dma pool API is only able to provide a
single descriptor per alloc invocation there is no guarantee that multiple
descriptors satisfy this requirement. Also the code in question is broken
as it only allocates memory for a single descriptor, without looking at the
number of descriptors required for the transfer, leading to out-of-bounds
accesses when the descriptors are written.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This reverts commit c1199875d327, as this depends on another commit
that is going to be reverted.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
It is troublesome to add a diagnostic like this to the Makefile
parse stage because the top-level Makefile could be parsed with
a stale include/config/auto.conf.
Once you are hit by the error about non-retpoline compiler, the
compilation still breaks even after disabling CONFIG_RETPOLINE.
The easiest fix is to move this check to the "archprepare" like
this commit did:
829fe4aa9ac1 ("x86: Allow generating user-space headers without a compiler")
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Fixes: 4cd24de3a098 ("x86/retpoline: Make CONFIG_RETPOLINE depend on compiler support")
Link: http://lkml.kernel.org/r/1543991239-18476-1-git-send-email-yamada.masahiro@socionext.com
Link: https://lkml.org/lkml/2018/12/4/206
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Internal to dax_unlock_mapping_entry(), dax_unlock_entry() is used to
store a replacement entry in the Xarray at the given xas-index with the
DAX_LOCKED bit clear. When called, dax_unlock_entry() expects the unlocked
value of the entry relative to the current Xarray state to be specified.
In most contexts dax_unlock_entry() is operating in the same scope as
the matched dax_lock_entry(). However, in the dax_unlock_mapping_entry()
case the implementation needs to recall the original entry. In the case
where the original entry is a 'pmd' entry it is possible that the pfn
performed to do the lookup is misaligned to the value retrieved in the
Xarray.
Change the api to return the unlock cookie from dax_lock_page() and pass
it to dax_unlock_page(). This fixes a bug where dax_unlock_page() was
assuming that the page was PMD-aligned if the entry was a PMD entry with
signatures like:
WARNING: CPU: 38 PID: 1396 at fs/dax.c:340 dax_insert_entry+0x2b2/0x2d0
RIP: 0010:dax_insert_entry+0x2b2/0x2d0
[..]
Call Trace:
dax_iomap_pte_fault.isra.41+0x791/0xde0
ext4_dax_huge_fault+0x16f/0x1f0
? up_read+0x1c/0xa0
__do_fault+0x1f/0x160
__handle_mm_fault+0x1033/0x1490
handle_mm_fault+0x18b/0x3d0
Link: https://lkml.kernel.org/r/20181130154902.GL10377@bombadil.infradead.org
Fixes: 9f32d221301c ("dax: Convert dax_lock_mapping_entry to XArray")
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
When the armada thermal module is inserted, removed and then reinserted,
the system panics as per the messages below. The reason is that "edit"
a live resource in the resource tree twice, and end up with it pointing
to some other hardware.
Editing live resources (resources that are part of the registered
resource tree) is not permissible - the resource tree is an ordered
set of resources, sorted by start address, and when a new resource is
inserted, it is validated that it (a) fits within its parent resource
and (b) does not overlap a neighbouring resource.
Get rid of this resource editing. We can instead adjust the return
value from ioremap() as ioremap() deals with the creation of page-
based mappings - provided the adjustment does not cross a page
boundary.
SError Interrupt on CPU1, code 0xbf000000 -- SError
CPU: 1 PID: 2749 Comm: modprobe Not tainted 4.19.0+ #175
Hardware name: Marvell 8040 MACCHIATOBin Double shot (DT)
pstate: 20400085 (nzCv daIf +PAN -UAO)
pc : regmap_mmio_read+0x3c/0x60
lr : regmap_mmio_read+0x3c/0x60
sp : ffffff800d453900
x29: ffffff800d453900 x28: ffffff800096a1d0
x27: 0000000000000100 x26: ffffff80009696d8
x25: ffffff8000969000 x24: ffffffc13a588918
x23: ffffffc13a9a28a8 x22: ffffff800d4539dc
x21: 0000000000000084 x20: ffffff800d4539dc
x19: ffffffc13a5d5480 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000030
x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f
x9 : 0000000000000000 x8 : ffffffc13a5d5a80
x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000000 x4 : 0000000000000000
x3 : ffffff800851be70 x2 : ffffff800851bd60
x1 : ffffff800d492ff8 x0 : 0000000000000000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 1 PID: 2749 Comm: modprobe Not tainted 4.19.0+ #175
Hardware name: Marvell 8040 MACCHIATOBin Double shot (DT)
Call trace:
dump_backtrace+0x0/0x158
show_stack+0x14/0x1c
dump_stack+0x90/0xb0
panic+0x128/0x298
print_tainted+0x0/0xa8
arm64_serror_panic+0x74/0x80
do_serror+0x5c/0xb8
el1_error+0xb4/0x144
regmap_mmio_read+0x3c/0x60
_regmap_bus_reg_read+0x18/0x20
_regmap_read+0x64/0x180
regmap_read+0x44/0x6c
armada_ap806_init+0x24/0x5c [armada_thermal]
armada_thermal_probe+0x2c8/0x37c [armada_thermal]
platform_drv_probe+0x4c/0xb0
really_probe+0x21c/0x2b4
driver_probe_device+0x58/0xfc
__driver_attach+0xd4/0xd8
bus_for_each_dev+0x50/0xa0
driver_attach+0x20/0x28
bus_add_driver+0x1c4/0x228
driver_register+0x6c/0x124
__platform_driver_register+0x4c/0x54
armada_thermal_driver_init+0x20/0x1000 [armada_thermal]
do_one_initcall+0x30/0x204
do_init_module+0x5c/0x1d4
load_module+0x1a88/0x212c
__se_sys_finit_module+0xa0/0xac
__arm64_sys_finit_module+0x1c/0x24
el0_svc_common+0x94/0xf0
el0_svc_handler+0x24/0x80
el0_svc+0x8/0x3c0
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0,21806000
Memory Limit: none
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
