summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-05-23soc: qcom: Add device tree binding for GSBIAndy Gross
Add device tree binding support for the QCOM GSBI driver. Signed-off-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Kumar Gala <galak@codeaurora.org>
2014-05-23ARM: dts: bcm590xx: add support for GPLDO and VBUS regulatorsMatt Porter
Adds additional nodes to support GPLDO1-6 and VBUS regulators which are now supported in the bcm590xx regulator driver. Signed-off-by: Matt Porter <mporter@linaro.org>
2014-05-23ARM: dts: AM4372: clk: efuse based crystal frequency detectAfzal Mohammed
Currently oscillator frequency is determined based on sysboot settings, it may not be the case always. To determine it properly, efuse settings also has to be read. CONTROL_STATUS register holds this information. Bit 31: if 0, frequency to be determined based on sysboot if 1, frequency to be determined based on efuse Bit 29,30 - for efuse detection of frequency Bit 22,23 - for sysboot detection of frequency Add clock nodes (mux) to determine oscillator frequency as above. Signed-off-by: Afzal Mohammed <afzal@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2014-05-23ARM: dts: am43xx-clocks.dtsi: add ti, set-rate-parent to display clock pathTomi Valkeinen
We need set-rate-parent flags for the display's clock path so that the DSS driver can change the clock rate of the PLL. This patchs adds the ti,set-rate-parent flag to disp_clk and dpll_disp_m2_ck clock nodes. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2014-05-23ARM: dts: omap5-clocks.dtsi: add ti, set-rate-parent to dss_dss_clkTomi Valkeinen
Add ti,set-rate-parent to dss_dss_clk so that the DSS driver can set the rate. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2014-05-23ARM: dts: omap4: add twd clock to DTGilles Chanteperdrix
Booting Linux 3.14 on Pandaboard currently gets the following message displayed: smp_twd: clock not found -2 Define "mpu_periphclk" as the twd clock in omap4 dts to avoid this. Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2014-05-23ARM: dts: omap54xx-clocks: Correct abe_iclk clock nodePeter Ujfalusi
abe_iclk's parent is aess_fclk and not abe_clk. Also correct the parameters for clock rate calculation as used for OMAP4 since in PRCM level there's no difference between the two platform regarding to AESS/ABE clocking. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2014-05-23ARM: dts: omap54xx-clocks: remove the autoidle properties for clock nodesPeter Ujfalusi
In OMAP5 bit 8 in PRCM registers are not defined (Reserved) unlike their counterpart in OMAP4. It is better to not write to these bits. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2014-05-23ARM: dts: am43x-clock: add tbclk data for ehrpwmPoddar, Sourav
We need "tbclk" clock data for the functioning of ehrpwm module. Hence, populating the required clock information in clock dts file. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2014-05-23ARM: dts: am33xx-clock: Fix ehrpwm tbclk dataPoddar, Sourav
tbclk does not need to be a composite clock, we can simply use gate clock for this purpose. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2014-05-22ARM: dts: msm: Add SDHC controller nodes for MSM8974 and DB8074 boardGeorgi Djakov
Add support for the 2 SDHC controllers on the DB8074 board. The first controller (at 0xf9824900) is connected to an on board soldered eMMC. The second controller (at 0xf98a4900) is connected to a uSD card slot. Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com> Signed-off-by: Kumar Gala <galak@codeaurora.org>
2014-05-22ARM: socfpga: dts: add watchdog0+1Steffen Trumtrar
The SoCFPGA has two watchdog timers. Add them to the dtsi. Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> [dinh: modified patch to have correct irq flag] Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
2014-05-22ARM: dts: socfpga: add gpio piecesSebastian Andrzej Siewior
The cycloneV has three gpio controllers, each one with 29 gpios. This patch adds the three controller with the gpio driver which is now sitting the gpio tree. Cc: devicetree@vger.kernel.org Acked-by: Alan Tull <atull@altera.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
2014-05-23ARM: dts: enable usb nodes for exynos4412-trats2Chanho Park
This patch enables exynos_usbphy and hsotg device nodes. Cc: Tomasz Figa <t.figa@samsung.com> Cc: Kamil Debski <k.debski@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chanho Park <chanho61.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: add hsotg device node for exynos4Chanho Park
This patch adds a hsotg node for exynos4 USB2.0 device controller. Cc: Tomasz Figa <t.figa@samsung.com> Cc: Kamil Debski <k.debski@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chanho Park <chanho61.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: add exynos_usbphy node for exynos4Chanho Park
This patch enables a exynos_usbphy node for exynos4 SoCs. A exynos4x12 usb phy node is almost same with 4210's one except compatible string and pmu syscon. Cc: Tomasz Figa <t.figa@samsung.com> Cc: Kamil Debski <k.debski@samsung.com> Signed-off-by: Chanho Park <chanho61.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: add PMU syscon node for exynos4Chanho Park
This patch adds a PMU(Power Management Unit) syscon node. This should be required for USB Phy syscon regmap I/F. Cc: Kamil Debski <k.debski@samsung.com> Signed-off-by: Chanho Park <chanho61.park@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: add pmu syscon handle to exynos5420 hdmiRahul Sharma
Add PMU syscon handle to HDMI dt node for controlling PHY Enable/Disable bit. Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: add pmu syscon handle to exynos5250 hdmiRahul Sharma
Add PMU syscon handle to HDMI dt node for controlling PHY Enable/Disable bit. Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: replace number by macro in clock binding for exynos5420Beomho Seo
sss module device node missed clock macro. This patch replace magic number with macro in clock binding for exynos5420. Signed-off-by: Beomho Seo <beomho.seo@samsung.com> Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: replace number by macro in clock binding for exynos5250Beomho Seo
Phy and sss module device node missed clock macro. This patch replace magic number with macros in clock binding for exynos5250. Signed-off-by: Beomho Seo <beomho.seo@samsung.com> Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: replace number by macro in clock binding for exynos4Beomho Seo
This patch replaces magic number of MIPI DSI Master node with macros in clock binding for exynos4 Signed-off-by: Beomho Seo <beomho.seo@samsung.com> Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: add external sd card node for exynos4210-universal_c210Marek Szyprowski
This patch enables support external SD card slot. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: add multimedia nodes for exynos4210-universal_c210Marek Szyprowski
This patch enables support for multimedia blocks - fimc in mem2mem mode, no camera sensors support yet. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: enable USB functionality for exynos4210-universal_c210Marek Szyprowski
This patch adds device tree nodes necessary to enable USB support on universalc210 board, this includes UDC controller (USB gadget) as well as EHCI and OHCI host ports. LDO3 and LDO8 regulators are switched to always on mode until EHCI and OHCI drivers will support them correctly. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: Enable USB gadget functionality for exynos4210-tratsTomasz Figa
This patch adds device tree nodes necessary to enable USB gadget functionality on Exynos4210-based Trats board. Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: Add audio subsystem nodes to exynos4.dtsiSylwester Nawrocki
This patch adds the audio subsystem clock controller and the I2S IP block nodes for Exynos4 SoC series. Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: fixed gpio key node for exynos4412-trats2Beomho Seo
This patch fixed gpio key device node. First, fix incorrect gpio property. And then, add ok-key node where locate bottom center. I have tested on exynos4412-trats2 board. Signed-off-by: Beomho Seo <beomho.seo@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-23ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2Beomho Seo
Exynos4412-trats2 board have light/proximity sensor. This patch add cm36651 light/ proximity sensor node for exynos4412. cm36651 is required properties as below. - Use i2c-gpio for cm36651 sensor. - Use fixed regulator for the IR LED. It is a part of the cm36651 for proximity detection. - cm36651 is i2c device driver so need to use i2c-gpio driver. Signed-off-by: Beomho Seo <beomho.seo@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-22ARM: dts: MSM8974: Add pinctrl nodeIvan T. Ivanov
Add the pin control node and pin definitions of SPI8. Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kumar Gala <galak@codeaurora.org>
2014-05-22ARM: at91: move sam9n12 SoC to the CCFBoris BREZILLON
This patch removes the selection of AT91_USE_OLD_CLK when selecting sam9n12 SoC support. This will automatically enable COMMON_CLK_AT91 option and add support for at91 common clk implementation. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Tested-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-05-22ARM: at91/dt: define sam9n12ek crystal frequenciesBoris BREZILLON
Define sam9n12ek's main and slow crystal frequencies. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Tested-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-05-22ARM: at91/dt: define sam9n12 clocksBoris BREZILLON
Define sam9n12 clocks and make use of them in peripheral definitions. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Tested-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-05-22ARM: at91: prepare common clk transition for sam9n12 SoCBoris BREZILLON
This patch encloses sam9n12 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91) #endif" sections. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Tested-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-05-22ARM: at91: move sam9x5 SoCs to the CCFBoris BREZILLON
This patch removes the selection of AT91_USE_OLD_CLK when selecting sam9x5 SoCs support. This will automatically enable COMMON_CLK_AT91 option and add support for at91 common clk implementation. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-05-22ARM: at91/dt: define sam9x5ek's crystal frequenciesBoris BREZILLON
Define sam9x5ek's main and slow crystal frequencies. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-05-22ARM: at91/dt: define sam9x5 clocksBoris BREZILLON
Define sam9x5 clocks in sam9x5 dt files and make use of them in peripheral definitions. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-05-22ARM: at91: prepare common clk transition for sam9x5 SoCsBoris BREZILLON
This patch encloses sam9x5 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91) #endif" sections. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-05-22Merge branch 'at91-3.16-cleanup' into at91-3.16-dt3Nicolas Ferre
2014-05-22Merge branch 'at91-3.15-fixes' into at91-3.16-dt3Nicolas Ferre
2014-05-22ARM: dts: sun7i: Add new i12-tvbox boardHans de Goede
The i12 tvbox is an A20 based android tvbox, with 512M / 1G RAM, 4G nand flash, ap6210 or ap6330 sdio wifi + bt (broadcom sdio wifi + uart attached brcm bt), 2USB host ports using USB-A receptacles and a micro-usb receptacle for USB OTG, and 100Mbit ethernet using an IP101a phy. The PCB is labelled i12-a20 hence I've named the board i12-a20. It is used in noname allwinner A20 tv-boxes, which are sometimes sold with Q5 or QT840A as product name. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-05-22ARM: dts: sun7i: cubietruck: set mmc3 bus-width propertyHans de Goede
bus-width defaults to 1, and all 4 lines are hooked up at the cubietruck, properly set bus-width to 4. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-05-22ARM: sun6i: Add MMC0 controller to the Colombus boardMaxime Ripard
The Colombus has a full size SD slot wired to the MMC0 controller. In order to work, the MMC lines have to have the pull-ups enabled though. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
2014-05-22ARM: sun6i: Fix OHCI2 node nameMaxime Ripard
The unit-address doesn't match the reg property. Since the reg property is correct, change the unit-address accordingly. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-05-22ARM: sun6i: Enable USB Host support on the Colombus boardMaxime Ripard
The colombus board has a on-board USB hub, that is enabled through the pin PH24, and wired to the first EHCI controller. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-05-21Merge tag 'samsung-dt' of ↵Olof Johansson
http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt Samsung DT updates for v3.16 - exynos4 : add missing pinctrls - exynos4412-trats2 : update camera nodes and add rear camera nodes : rename alias for i2c_ak8975 label Update camera nodes for exynos4 and exynos4412-trats2 - exynos5250 : update DWC3 usb controller and enable to use generic USB DRD phy - exynos5250-snow : enable dp-controller, fimd, hdmi and pwm backlight : add sound node and Vbus regulator for USB 3.0 : add tps65090 power regulator : add pinctrl for EC irq and i2c-arbitrator - exynos5420 : change to correct compatible string for hdmi : add PD entry to MFC codec and enable DWC3 and USB 3.0 PHY : add MFC memory banks for smdk5420 and arndale-octa boards - exynos5420-peach-pit : add support exynos5420 based peach-pit board : add sound node and Vbus regulatro for USB 3.0 : enable dp-controller, fimd - exynos5420-smdk5420 : add Vbus regulatro for USB 3.0 - use generic DT bindings for map SYSRAM [olof: Fixed up conflict with a fix for 4212 secondary CPU startup, carrying over the fix to the reworked code] * tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits) ARM: dts: Add MFC memory banks to exynos5420 boards ARM: dts: enable dp-controller for exynos5420-peach-pit board ARM: dts: enable fimd for exynos5420 based peach-pit board ARM: dts: enable dp-controller for exynos5250-snow board ARM: dts: enable fimd for exynos5250-snow board ARM: dts: enable pwm backlight for exynos5250-snow ARM: dts: Add pwmX_out pinctrl nodes to exynos5250 ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-smdk5420 ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-peach-pit ARM: dts: Add Vbus regulator for USB 3.0 on exynos5250-snow ARM: dts: Add PD entry to MFC codec on exynos5420 ARM: dts: Add sound node for exynos5420-peach-pit board ARM: dts: Add sound node for exynos5250-snow board ARM: dts: Update DWC3 usb controller to use new phy driver for exynos5250 ARM: dts: Enable support for generic USB DRD phy for exynos5250 ARM: dts: Enable support for DWC3 controller for exynos5420 ARM: dts: Enable support for USB 3.0 PHY controller for exynos5420 ARM: dts: enable hdmi for exynos5420-peach-pit board ARM: dts: change to correct compatible string for exynos5420 hdmi ARM: dts: enable hdmi for exynos5250 based snow board ... Signed-off-by: Olof Johansson <olof@lixom.net>
2014-05-21Merge commit '702b691e4a71' into next/dtOlof Johansson
Merging in Samsung fixes for 3.15-rc to avoid an annoying context conflict with new DT code. * commit '702b691e4a71': ARM: dts: Remove g2d_pd node for exynos5420 ARM: dts: Remove mau_pd node for exynos5420 ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount ARM: dts: disable MDMA1 node for exynos5420 ARM: EXYNOS: fix the secondary CPU boot of exynos4212 Signed-off-by: Olof Johansson <olof@lixom.net>
2014-05-22ARM: dts: Add USB 2.0 support on exynos5420Vivek Gautam
Add required device node for ehci and ohci controllers to enable USB 2.0 support. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-22ARM: dts: Add usb2phy support on exynos5420Vivek Gautam
Add required device node for usb2phy to let enable USB 2.0 support. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-05-22ARM: dts: Add usb2phy to exynos5250Kamil Debski
Add support to PHY of USB2 of the Exynos5250 SoC. Signed-off-by: Kamil Debski <k.debski@samsung.com> [gautam.vivek@samsung.com: Split the usb phy entries] [gautam.vivek@samsung.com: Added phy entry for OHCI also along with EHCI] Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
generated by cgit (git 2.34.1) at 2025-07-15 13:04:29 +0000