| Age | Commit message (Collapse) | Author |
|---|
|
In WRED mode, the backlog for a single virtual queue (VQ) should not be
used to determine queue behavior; instead the backlog is summed across
all VQs. This sum is currently used when calculating the average queue
lengths. It also needs to be used when determining if the queue's hard
limit has been reached, or when reporting each VQ's backlog via netlink.
q->backlog will only be used if the queue switches out of WRED mode.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After receiving a PADT and the socket is closed, user space will no
longer drop the reference to the pppoe device.
This leads to errors like this:
[ 488.570000] unregister_netdevice: waiting for eth0.2 to become free. Usage count = 2
Fixes: 287f3a943fe ("pppoe: Use workqueue to die properly when a PADT is received")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stage 1 translation is controlled by two sets of page tables (TTBR0 and
TTBR1) which grow up and down from zero respectively in the ARMv8
translation regime. For the SMMU, we only care about TTBR0 and, in the
case of a 48-bit virtual space, we expect to map virtual addresses 0x0
through to 0xffff_ffff_ffff.
Given that some masters may be incapable of emitting virtual addresses
targetting TTBR1 (e.g. because they sit on a 48-bit bus), the SMMU
architecture allows bit 47 to be sign-extended, halving the virtual
range of TTBR0 but allowing TTBR1 to be used. This is controlled by the
SEP field in TTBCR2.
The SMMU driver incorrectly enables this sign-extension feature, which
causes problems when userspace addresses are programmed into a master
device with the SMMU expecting to map the incoming transactions via
TTBR0; if the top bit of address is set, we will instead get a
translation fault since TTBR1 walks are disabled in the TTBCR.
This patch fixes the issue by disabling sign-extension of a fixed
virtual address bit and instead basing the behaviour on the upstream bus
size: the incoming address is zero extended unless the upstream bus is
only 49 bits wide, in which case bit 48 is used as the sign bit and is
replicated to the upper bits.
Cc: <stable@vger.kernel.org> # v4.0+
Reported-by: Varun Sethi <varun.sethi@freescale.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
'spi/fix/fsl-espi' into spi-linus
|
|
spi: Fixes for v4.1
A few driver fixes plus two changes for the core, one to make the
setup_transfer() callback optional which fixes crashes in some drivers
which were updated to use new interfaces without apparent testing and
one to ensure we don't expose the data buffers we use for dummy
transfers to drivers which avoids potential issues with multiple
accesses to them or reuse.
# gpg: Signature made Sat 25 Apr 2015 10:59:47 BST using RSA key ID 5D5487D0
# gpg: key CD7BEEBC: no public key for trusted key - skipped
# gpg: key CD7BEEBC marked as ultimately trusted
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 16005C11: no public key for trusted key - skipped
# gpg: key 16005C11 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: key 5C6153AD: no public key for trusted key - skipped
# gpg: key 5C6153AD marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
|
|
Registering the netdev before setting the priv data is unsafe.
So fix this possible race by setting the priv data first.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: <stable@vger.kernel.org> # v3.18+
Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a race between releasing extent buffers that are flagged as stale
and recycling them that makes us it the following BUG_ON at
btrfs_release_extent_buffer_page:
BUG_ON(extent_buffer_under_io(eb))
The BUG_ON is triggered because the extent buffer has the flag
EXTENT_BUFFER_DIRTY set as a consequence of having been reused and made
dirty by another concurrent task.
Here follows a sequence of steps that leads to the BUG_ON.
CPU 0 CPU 1 CPU 2
path->nodes[0] == eb X
X->refs == 2 (1 for the tree, 1 for the path)
btrfs_header_generation(X) == current trans id
flag EXTENT_BUFFER_DIRTY set on X
btrfs_release_path(path)
unlocks X
reads eb X
X->refs incremented to 3
locks eb X
btrfs_del_items(X)
X becomes empty
clean_tree_block(X)
clear EXTENT_BUFFER_DIRTY from X
btrfs_del_leaf(X)
unlocks X
extent_buffer_get(X)
X->refs incremented to 4
btrfs_free_tree_block(X)
X's range is not pinned
X's range added to free
space cache
free_extent_buffer_stale(X)
lock X->refs_lock
set EXTENT_BUFFER_STALE on X
release_extent_buffer(X)
X->refs decremented to 3
unlocks X->refs_lock
btrfs_release_path()
unlocks X
free_extent_buffer(X)
X->refs becomes 2
__btrfs_cow_block(Y)
btrfs_alloc_tree_block()
btrfs_reserve_extent()
find_free_extent()
gets offset == X->start
btrfs_init_new_buffer(X->start)
btrfs_find_create_tree_block(X->start)
alloc_extent_buffer(X->start)
find_extent_buffer(X->start)
finds eb X in radix tree
free_extent_buffer(X)
lock X->refs_lock
test X->refs == 2
test bit EXTENT_BUFFER_STALE is set
test !extent_buffer_under_io(eb)
increments X->refs to 3
mark_extent_buffer_accessed(X)
check_buffer_tree_ref(X)
--> does nothing,
X->refs >= 2 and
EXTENT_BUFFER_TREE_REF
is set in X
clear EXTENT_BUFFER_STALE from X
locks X
btrfs_mark_buffer_dirty()
set_extent_buffer_dirty(X)
check_buffer_tree_ref(X)
--> does nothing, X->refs >= 2 and
EXTENT_BUFFER_TREE_REF is set
sets EXTENT_BUFFER_DIRTY on X
test and clear EXTENT_BUFFER_TREE_REF
decrements X->refs to 2
release_extent_buffer(X)
decrements X->refs to 1
unlock X->refs_lock
unlock X
free_extent_buffer(X)
lock X->refs_lock
release_extent_buffer(X)
decrements X->refs to 0
btrfs_release_extent_buffer_page(X)
BUG_ON(extent_buffer_under_io(X))
--> EXTENT_BUFFER_DIRTY set on X
Fix this by making find_extent buffer wait for any ongoing task currently
executing free_extent_buffer()/free_extent_buffer_stale() if the extent
buffer has the stale flag set.
A more clean alternative would be to always increment the extent buffer's
reference count while holding its refs_lock spinlock but find_extent_buffer
is a performance critical area and that would cause lock contention whenever
multiple tasks search for the same extent buffer concurrently.
A build server running a SLES 12 kernel (3.12 kernel + over 450 upstream
btrfs patches backported from newer kernels) was hitting this often:
[1212302.461948] kernel BUG at ../fs/btrfs/extent_io.c:4507!
(...)
[1212302.470219] CPU: 1 PID: 19259 Comm: bs_sched Not tainted 3.12.36-38-default #1
[1212302.540792] Hardware name: Supermicro PDSM4/PDSM4, BIOS 6.00 04/17/2006
[1212302.540792] task: ffff8800e07e0100 ti: ffff8800d6412000 task.ti: ffff8800d6412000
[1212302.540792] RIP: 0010:[<ffffffffa0507081>] [<ffffffffa0507081>] btrfs_release_extent_buffer_page.constprop.51+0x101/0x110 [btrfs]
(...)
[1212302.630008] Call Trace:
[1212302.630008] [<ffffffffa05070cd>] release_extent_buffer+0x3d/0xa0 [btrfs]
[1212302.630008] [<ffffffffa04c2d9d>] btrfs_release_path+0x1d/0xa0 [btrfs]
[1212302.630008] [<ffffffffa04c5c7e>] read_block_for_search.isra.33+0x13e/0x3a0 [btrfs]
[1212302.630008] [<ffffffffa04c8094>] btrfs_search_slot+0x3f4/0xa80 [btrfs]
[1212302.630008] [<ffffffffa04cf5d8>] lookup_inline_extent_backref+0xf8/0x630 [btrfs]
[1212302.630008] [<ffffffffa04d13dd>] __btrfs_free_extent+0x11d/0xc40 [btrfs]
[1212302.630008] [<ffffffffa04d64a4>] __btrfs_run_delayed_refs+0x394/0x11d0 [btrfs]
[1212302.630008] [<ffffffffa04db379>] btrfs_run_delayed_refs.part.66+0x69/0x280 [btrfs]
[1212302.630008] [<ffffffffa04ed2ad>] __btrfs_end_transaction+0x2ad/0x3d0 [btrfs]
[1212302.630008] [<ffffffffa04f7505>] btrfs_evict_inode+0x4a5/0x500 [btrfs]
[1212302.630008] [<ffffffff811b9e28>] evict+0xa8/0x190
[1212302.630008] [<ffffffff811b0330>] do_unlinkat+0x1a0/0x2b0
I was also able to reproduce this on a 3.19 kernel, corresponding to Chris'
integration branch from about a month ago, running the following stress
test on a qemu/kvm guest (with 4 virtual cpus and 16Gb of ram):
while true; do
mkfs.btrfs -l 4096 -f -b `expr 20 \* 1024 \* 1024 \* 1024` /dev/sdd
mount /dev/sdd /mnt
snapshot_cmd="btrfs subvolume snapshot -r /mnt"
snapshot_cmd="$snapshot_cmd /mnt/snap_\`date +'%H_%M_%S_%N'\`"
fsstress -d /mnt -n 25000 -p 8 -x "$snapshot_cmd" -X 100
umount /mnt
done
Which usually triggers the BUG_ON within less than 24 hours:
[49558.618097] ------------[ cut here ]------------
[49558.619732] kernel BUG at fs/btrfs/extent_io.c:4551!
(...)
[49558.620031] CPU: 3 PID: 23908 Comm: fsstress Tainted: G W 3.19.0-btrfs-next-7+ #3
[49558.620031] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
[49558.620031] task: ffff8800319fc0d0 ti: ffff880220da8000 task.ti: ffff880220da8000
[49558.620031] RIP: 0010:[<ffffffffa0476b1a>] [<ffffffffa0476b1a>] btrfs_release_extent_buffer_page+0x20/0xe9 [btrfs]
(...)
[49558.620031] Call Trace:
[49558.620031] [<ffffffffa0476c73>] release_extent_buffer+0x90/0xd3 [btrfs]
[49558.620031] [<ffffffff8142b10c>] ? _raw_spin_lock+0x3b/0x43
[49558.620031] [<ffffffffa0477052>] ? free_extent_buffer+0x37/0x94 [btrfs]
[49558.620031] [<ffffffffa04770ab>] free_extent_buffer+0x90/0x94 [btrfs]
[49558.620031] [<ffffffffa04396d5>] btrfs_release_path+0x4a/0x69 [btrfs]
[49558.620031] [<ffffffffa0444907>] __btrfs_free_extent+0x778/0x80c [btrfs]
[49558.620031] [<ffffffffa044a485>] __btrfs_run_delayed_refs+0xad2/0xc62 [btrfs]
[49558.728054] [<ffffffff811420d5>] ? kmemleak_alloc_recursive.constprop.52+0x16/0x18
[49558.728054] [<ffffffffa044c1e8>] btrfs_run_delayed_refs+0x6d/0x1ba [btrfs]
[49558.728054] [<ffffffffa045917f>] ? join_transaction.isra.9+0xb9/0x36b [btrfs]
[49558.728054] [<ffffffffa045a75c>] btrfs_commit_transaction+0x4c/0x981 [btrfs]
[49558.728054] [<ffffffffa0434f86>] btrfs_sync_fs+0xd5/0x10d [btrfs]
[49558.728054] [<ffffffff81155923>] ? iterate_supers+0x60/0xc4
[49558.728054] [<ffffffff8117966a>] ? do_sync_work+0x91/0x91
[49558.728054] [<ffffffff8117968a>] sync_fs_one_sb+0x20/0x22
[49558.728054] [<ffffffff81155939>] iterate_supers+0x76/0xc4
[49558.728054] [<ffffffff811798e8>] sys_sync+0x55/0x83
[49558.728054] [<ffffffff8142bbd2>] system_call_fastpath+0x12/0x17
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
So creating a block group has 2 distinct phases:
Phase 1 - creates the btrfs_block_group_cache item and adds it to the
rbtree fs_info->block_group_cache_tree and to the corresponding list
space_info->block_groups[];
Phase 2 - adds the block group item to the extent tree and corresponding
items to the chunk tree.
The first phase adds the block_group_cache_item to a list of pending block
groups in the transaction handle, and phase 2 happens when
btrfs_end_transaction() is called against the transaction handle.
It happens that once phase 1 completes, other concurrent tasks that use
their own transaction handle, but points to the same running transaction
(struct btrfs_trans_handle->transaction), can use this block group for
space allocations and therefore mark it dirty. Dirty block groups are
tracked in a list belonging to the currently running transaction (struct
btrfs_transaction) and not in the transaction handle (btrfs_trans_handle).
This is a problem because once a task calls btrfs_commit_transaction(),
it calls btrfs_start_dirty_block_groups() which will see all dirty block
groups and attempt to start their writeout, including those that are
still attached to the transaction handle of some concurrent task that
hasn't called btrfs_end_transaction() yet - which means those block
groups haven't gone through phase 2 yet and therefore when
write_one_cache_group() is called, it won't find the block group items
in the extent tree and abort the current transaction with -ENOENT,
turning the fs into readonly mode and require a remount.
Fix this by ignoring -ENOENT when looking for block group items in the
extent tree when we attempt to start the writeout of the block group
caches outside the critical section of the transaction commit. We will
try again later during the critical section and if there we still don't
find the block group item in the extent tree, we then abort the current
transaction.
This issue happened twice, once while running fstests btrfs/067 and once
for btrfs/078, which produced the following trace:
[ 3278.703014] WARNING: CPU: 7 PID: 18499 at fs/btrfs/super.c:260 __btrfs_abort_transaction+0x52/0x114 [btrfs]()
[ 3278.707329] BTRFS: Transaction aborted (error -2)
(...)
[ 3278.731555] Call Trace:
[ 3278.732396] [<ffffffff8142fa46>] dump_stack+0x4f/0x7b
[ 3278.733860] [<ffffffff8108b6a2>] ? console_unlock+0x361/0x3ad
[ 3278.735312] [<ffffffff81045ea5>] warn_slowpath_common+0xa1/0xbb
[ 3278.736874] [<ffffffffa03ada6d>] ? __btrfs_abort_transaction+0x52/0x114 [btrfs]
[ 3278.738302] [<ffffffff81045f05>] warn_slowpath_fmt+0x46/0x48
[ 3278.739520] [<ffffffffa03ada6d>] __btrfs_abort_transaction+0x52/0x114 [btrfs]
[ 3278.741222] [<ffffffffa03b9e56>] write_one_cache_group+0xae/0xbf [btrfs]
[ 3278.742797] [<ffffffffa03c487b>] btrfs_start_dirty_block_groups+0x170/0x2b2 [btrfs]
[ 3278.744492] [<ffffffffa03d309c>] btrfs_commit_transaction+0x130/0x9c9 [btrfs]
[ 3278.746084] [<ffffffff8107d33d>] ? trace_hardirqs_on+0xd/0xf
[ 3278.747249] [<ffffffffa03e5660>] btrfs_sync_file+0x313/0x387 [btrfs]
[ 3278.748744] [<ffffffff8117acad>] vfs_fsync_range+0x95/0xa4
[ 3278.749958] [<ffffffff81435b54>] ? ret_from_sys_call+0x1d/0x58
[ 3278.751218] [<ffffffff8117acd8>] vfs_fsync+0x1c/0x1e
[ 3278.754197] [<ffffffff8117ae54>] do_fsync+0x34/0x4e
[ 3278.755192] [<ffffffff8117b07c>] SyS_fsync+0x10/0x14
[ 3278.756236] [<ffffffff81435b32>] system_call_fastpath+0x12/0x17
[ 3278.757366] ---[ end trace 9a4d4df4969709aa ]---
Fixes: 1bbc621ef284 ("Btrfs: allow block group cache writeout
outside critical section in commit")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
When waiting for the writeback of block group cache we returned
immediately if there was an error during writeback without waiting
for the ordered extent to complete. This left a short time window
where if some other task attempts to start the writeout for the same
block group cache it can attempt to add a new ordered extent, starting
at the same offset (0) before the previous one is removed from the
ordered tree, causing an ordered tree panic (calls BUG()).
This normally doesn't happen in other write paths, such as buffered
writes or direct IO writes for regular files, since before marking
page ranges dirty we lock the ranges and wait for any ordered extents
within the range to complete first.
Fix this by making btrfs_wait_ordered_range() not return immediately
if it gets an error from the writeback, waiting for all ordered extents
to complete first.
This issue happened often when running the fstest btrfs/088 and it's
easy to trigger it by running in a loop until the panic happens:
for ((i = 1; i <= 10000; i++)) do ./check btrfs/088 ; done
[17156.862573] BTRFS critical (device sdc): panic in ordered_data_tree_panic:70: Inconsistency in ordered tree at offset 0 (errno=-17 Object already exists)
[17156.864052] ------------[ cut here ]------------
[17156.864052] kernel BUG at fs/btrfs/ordered-data.c:70!
(...)
[17156.864052] Call Trace:
[17156.864052] [<ffffffffa03876e3>] btrfs_add_ordered_extent+0x12/0x14 [btrfs]
[17156.864052] [<ffffffffa03787e2>] run_delalloc_nocow+0x5bf/0x747 [btrfs]
[17156.864052] [<ffffffffa03789ff>] run_delalloc_range+0x95/0x353 [btrfs]
[17156.864052] [<ffffffffa038b7fe>] writepage_delalloc.isra.16+0xb9/0x13f [btrfs]
[17156.864052] [<ffffffffa038d75b>] __extent_writepage+0x129/0x1f7 [btrfs]
[17156.864052] [<ffffffffa038da5a>] extent_write_cache_pages.isra.15.constprop.28+0x231/0x2f4 [btrfs]
[17156.864052] [<ffffffff810ad2af>] ? __module_text_address+0x12/0x59
[17156.864052] [<ffffffff8107d33d>] ? trace_hardirqs_on+0xd/0xf
[17156.864052] [<ffffffffa038df76>] extent_writepages+0x4b/0x5c [btrfs]
[17156.864052] [<ffffffff81144431>] ? kmem_cache_free+0x9b/0xce
[17156.864052] [<ffffffffa0376a46>] ? btrfs_submit_direct+0x3fc/0x3fc [btrfs]
[17156.864052] [<ffffffffa0389cd6>] ? free_extent_state+0x8c/0xc1 [btrfs]
[17156.864052] [<ffffffffa0374871>] btrfs_writepages+0x28/0x2a [btrfs]
[17156.864052] [<ffffffff8110c4c8>] do_writepages+0x23/0x2c
[17156.864052] [<ffffffff81102f36>] __filemap_fdatawrite_range+0x5a/0x61
[17156.864052] [<ffffffff81102f6e>] filemap_fdatawrite_range+0x13/0x15
[17156.864052] [<ffffffffa0383ef7>] btrfs_fdatawrite_range+0x21/0x48 [btrfs]
[17156.864052] [<ffffffffa03ab89e>] __btrfs_write_out_cache.isra.14+0x2d9/0x3a7 [btrfs]
[17156.864052] [<ffffffffa03ac1ab>] ? btrfs_write_out_cache+0x41/0xdc [btrfs]
[17156.864052] [<ffffffffa03ac1fd>] btrfs_write_out_cache+0x93/0xdc [btrfs]
[17156.864052] [<ffffffffa0363847>] ? btrfs_start_dirty_block_groups+0x13a/0x2b2 [btrfs]
[17156.864052] [<ffffffffa03638e6>] btrfs_start_dirty_block_groups+0x1d9/0x2b2 [btrfs]
[17156.864052] [<ffffffff8107d33d>] ? trace_hardirqs_on+0xd/0xf
[17156.864052] [<ffffffffa037209e>] btrfs_commit_transaction+0x130/0x9c9 [btrfs]
[17156.864052] [<ffffffffa034c748>] btrfs_sync_fs+0xe1/0x12d [btrfs]
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
If the writeback of an inode cache failed we were unnecessarilly
attempting to release again the delalloc metadata that we previously
reserved. However attempting to do this a second time triggers an
assertion at drop_outstanding_extent() because we have no more
outstanding extents for our inode cache's inode. If we were able
to start writeback of the cache the reserved metadata space is
released at btrfs_finished_ordered_io(), even if an error happens
during writeback.
So make sure we don't repeat the metadata space release if writeback
started for our inode cache.
This issue was trivial to reproduce by running the fstest btrfs/088
with "-o inode_cache", which triggered the assertion leading to a
BUG() call and requiring a reboot in order to run the remaining
fstests. Trace produced by btrfs/088:
[255289.385904] BTRFS: assertion failed: BTRFS_I(inode)->outstanding_extents >= num_extents, file: fs/btrfs/extent-tree.c, line: 5276
[255289.388094] ------------[ cut here ]------------
[255289.389184] kernel BUG at fs/btrfs/ctree.h:4057!
[255289.390125] invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
(...)
[255289.392068] Call Trace:
[255289.392068] [<ffffffffa035e774>] drop_outstanding_extent+0x3d/0x6d [btrfs]
[255289.392068] [<ffffffffa0364988>] btrfs_delalloc_release_metadata+0x54/0xe3 [btrfs]
[255289.392068] [<ffffffffa03b4174>] btrfs_write_out_ino_cache+0x95/0xad [btrfs]
[255289.392068] [<ffffffffa036f5c4>] btrfs_save_ino_cache+0x275/0x2dc [btrfs]
[255289.392068] [<ffffffffa03e2d83>] commit_fs_roots.isra.12+0xaa/0x137 [btrfs]
[255289.392068] [<ffffffff8107d33d>] ? trace_hardirqs_on+0xd/0xf
[255289.392068] [<ffffffffa037841f>] ? btrfs_commit_transaction+0x4b1/0x9c9 [btrfs]
[255289.392068] [<ffffffff814351a4>] ? _raw_spin_unlock+0x32/0x46
[255289.392068] [<ffffffffa037842e>] btrfs_commit_transaction+0x4c0/0x9c9 [btrfs]
(...)
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
This patch fixes a timing issue that causes a GPU hang when the system
comes out of power saving.
During pm_resume, We are submitting batchbuffers before enabling
Interrupts this is causing us to miss the context switch interrupt,
and in consequence intel_execlists_handle_ctx_events is not triggered.
This patch is based on a patch from Deepak S <deepak.s@intel.com>
from another platform.
The patch fixes an issue introduced by:
commit e7778be1eab918274f79603d7c17b3ec8be77386
drm/i915: Fix startup failure in LRC mode after recent init changes
The above patch added a call to init_context() to fix an issue introduced
by a previous patch. But, it then opened up a small timing window for the
batches being added by the init_context (basically setting up the context)
to complete before the interrupts have been turned on, thus hanging the
GPU.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89600
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: fixed typo in subject, massaged the comments a bit]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Si5351 clock generator on CuBox uses XTAL as clock reference, name the
clock phandle accordingly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
This patch enables RAPL counters (energy consumption counters)
support for Intel Broadwell-U processors (Model 61):
To use:
$ perf stat -a -I 1000 -e power/energy-cores/,power/energy-pkg/,power/energy-ram/ sleep 10
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jacob.jun.pan@linux.intel.com
Cc: kan.liang@intel.com
Cc: peterz@infradead.org
Cc: sonnyrao@chromium.org
Link: http://lkml.kernel.org/r/20150423070709.GA4970@thinkpad
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Change HOST_EXTRACFLAGS to include arch/x86/include/uapi along
with include/uapi.
This looks more consistent, and this fixes "make bzImage" on my
old distro which doesn't have asm/bitsperlong.h in /usr/include/.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 6f121e548f83 ("x86, vdso: Reimplement vdso.so preparation in build-time C")
Link: http://lkml.kernel.org/r/1431332153-18566-6-git-send-email-bp@alien8.de
Link: http://lkml.kernel.org/r/20150507165835.GB18652@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
When the bus id was supplied via a struct platform_device, the driver wasn't
handling -1 to mean an unspecified id of the only instance of this driver,
as the platform spec requires.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an issue where the send(MSG_DONTWAIT) call
on a TX_RING is not fully non-blocking in cases where the device's sndBuf is
full. We pass nonblock=true to sock_alloc_send_skb() and return any possibly
occuring error code (most likely EGAIN) to the caller. As the fast-path stays
as it is, we keep the unlikely() around skb == NULL.
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 12a8541d5c82 "bnx2x: Delay during kdump load" added a 5 seconds
delay to bnx2x's probe function in the kdump case to let the firmware
realize the old driver is gone.
The problem with the delay is that it is per-device, so if you have
several bnx2x NICs in NPAR mode, the delays can accumulate to minutes.
Fix it by adjusting the delay so that we do not wait more than
necessary, i.e. no more delaying after 5 seconds of kernel boot time.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
value can't fit into 12bits.
The ARM JIT code emits "ldr rX, [pc, #offset]" to access the literal
pool. #offset maximum value is 4095 and if the generated code is too
large, the #offset value can overflow and not point to the expected
slot in the literal pool. Additionally, when overflow occurs, bits of
the overflow can end up changing the destination register of the ldr
instruction.
Fix that by detecting the overflow in imm_offset() and setting a flag
that is checked for each BPF instructions converted in
build_body(). As of now it can only be detected in the second pass. As
a result the second build_body() call can now fail, so add the
corresponding cleanup code in that case.
Using multiple literal pools in the JITed code is going to require
lots of intrusive changes to the JIT code (which would better be done
as a feature instead of fix), just delegating to the kernel BPF
interpreter in that case is a more straight forward, minimal fix and
easy to backport.
Fixes: ddecdfcea0ae ("ARM: 7259/3: net: JIT compiler for packet filters")
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In that case, emit_udiv() will be called with rn == ARM_R0 (r_scratch)
and loading rm first into ARM_R0 will result in jit_udiv() function
being called the same dividend and divisor. Fix that by loading rn
first into ARM_R1 and then rm into ARM_R0.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Cc: <stable@vger.kernel.org> # v3.13+
Fixes: aee636c4809f (bpf: do not use reciprocal divide)
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Pull drm fixes from Dave Airlie:
"I really need to get back to sending these on my Friday, instead of my
Monday morning, but nothing too amazing in here: a few amdkfd fixes, a
few radeon fixes, i915 fixes, one tegra fix and one core fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Zero out invalid vblank timestamp in drm_update_vblank_count.
drm/tegra: Don't use vblank_disable_immediate on incapable driver.
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
drm/radeon: make UVD handle checking more strict
drm/radeon: make VCE handle check more strict
drm/radeon: fix userptr lockup
drm/radeon: fix userptr BO unpin bug v3
drm/amdkfd: Initialize sdma vm when creating sdma queue
drm/amdkfd: Don't report local memory size
drm/amdkfd: allow unregister process with queues
drm/i915: Drop PIPE-A quirk for 945GSE HP Mini
drm/i915: Sink rate read should be saved in deca-kHz
drm/i915/dp: there is no audio on port A
drm/i915: Add missing MacBook Pro models with dual channel LVDS
drm/i915: Assume dual channel LVDS if pixel clock necessitates it
drm/radeon: don't setup audio on asics that don't support it
drm/radeon: disable semaphores for UVD V1 (v2)
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
misc i915 fixes.
* tag 'drm-intel-fixes-2015-05-08' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Drop PIPE-A quirk for 945GSE HP Mini
drm/i915: Sink rate read should be saved in deca-kHz
drm/i915/dp: there is no audio on port A
drm/i915: Add missing MacBook Pro models with dual channel LVDS
drm/i915: Assume dual channel LVDS if pixel clock necessitates it
|
|
Since commit 844b03f27739135fe1fed2fef06da0ffc4c7a081 we make
sure that after vblank irq off, we return the last valid
(vblank count, vblank timestamp) pair to clients, e.g., during
modesets, which is good.
An overlooked side effect of that commit for kms drivers without
support for precise vblank timestamping is that at vblank irq
enable, when we update the vblank counter from the hw counter, we
can't update the corresponding vblank timestamp, so now we have a
totally mismatched timestamp for the new count to confuse clients.
Restore old client visible behaviour from before Linux 3.17, but
zero out the timestamp at vblank counter update (instead of disable
as in original implementation) if we can't generate a meaningful
timestamp immediately for the new vblank counter. This will fix
this regression, so callers know they need to retry again later
if they need a valid timestamp, but at the same time preserves
the improvements made in the commit mentioned above.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> #v3.17+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Pull ARM fixes from Russell King:
"A set of ARM fixes:
- fix an off-by-one error in the iommu DMA ops, which caused errors
with a 4GiB size.
- remove comments mentioning the non-existent CONFIG_CPU_ARM1020_CPU_IDLE
macro.
- remove useless CONFIG_CPU_ICACHE_STREAMING_DISABLE blocks, where
this symbol never appeared in any Kconfig.
- fix Feroceon code to cope with a previous change correctly (it
incorrectly left an additional word in an assembly structure
definition)
- avoid a misleading IRQ affinity warning in the ARM PMU code for
IRQs which are already affine to their CPUs.
- fix the node name printed in the IRQ affinity warning"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8352/1: perf: Fix the pmu node name in warning message
ARM: 8351/1: perf: don't warn about missing interrupt-affinity property for PPIs
ARM: 8350/1: proc-feroceon: Fix feroceon_proc_info macro
ARM: 8349/1: arch/arm/mm/proc-arm925.S: remove dead #ifdef block
ARM: 8348/1: remove comments on CPU_ARM1020_CPU_IDLE
ARM: 8347/1: dma-mapping: fix off-by-one check in arm_setup_iommu_dma_ops
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
Pull samsung fixes from Kukjin Kim:
"Here is Samsung fixes for v4.1. Since I've missed to send this via
arm-soc tree before v4.1-rc3, so I'm sending this to you directly
- fix commit ea08de16eb1b ("ARM: dts: Add DISP1 power domain for
exynos5420") which causes 'unhandled fault: imprecise external
abort' error when PD turned off. ("make DP a consumer of DISP1
power domain")
- fix 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards ("add
'rtc_src' clock to rtc node for source clock of rtc")
- fix typo for 'cpu-crit-0' trip point on exynos5420/5440
- fix S2R failure on exynos5250-snow due to card power of Marvell
WiFi driver (suspend/resume) ("add keep-power-in-susped to WiFi
SDIO node")"
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
|
|
A read() from a pty master may mistakenly indicate EOF (errno == -EIO)
after the pty slave has closed, even though input data remains to be read.
For example,
pty slave | input worker | pty master
| |
| | n_tty_read()
pty_write() | | input avail? no
add data | | sleep
schedule worker --->| | .
|---> flush_to_ldisc() | .
pty_close() | fill read buffer | .
wait for worker | wakeup reader --->| .
| read buffer full? |---> input avail ? yes
|<--- yes - exit worker | copy 4096 bytes to user
TTY_OTHER_CLOSED <---| |<--- kick worker
| |
**** New read() before worker starts ****
| | n_tty_read()
| | input avail? no
| | TTY_OTHER_CLOSED? yes
| | return -EIO
Several conditions are required to trigger this race:
1. the ldisc read buffer must become full so the input worker exits
2. the read() count parameter must be >= 4096 so the ldisc read buffer
is empty
3. the subsequent read() occurs before the kicked worker has processed
more input
However, the underlying cause of the race is that data is pipelined, while
tty state is not; ie., data already written by the pty slave end is not
yet visible to the pty master end, but state changes by the pty slave end
are visible to the pty master end immediately.
Pipeline the TTY_OTHER_CLOSED state through input worker to the reader.
1. Introduce TTY_OTHER_DONE which is set by the input worker when
TTY_OTHER_CLOSED is set and either the input buffers are flushed or
input processing has completed. Readers/polls are woken when
TTY_OTHER_DONE is set.
2. Reader/poll checks TTY_OTHER_DONE instead of TTY_OTHER_CLOSED.
3. A new input worker is started from pty_close() after setting
TTY_OTHER_CLOSED, which ensures the TTY_OTHER_DONE state will be
set if the last input worker is already finished (or just about to
exit).
Remove tty_flush_to_ldisc(); no in-tree callers.
Fixes: 52bce7f8d4fc ("pty, n_tty: Simplify input processing on final close")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96311
BugLink: http://bugs.launchpad.net/bugs/1429756
Cc: <stable@vger.kernel.org> # 3.19+
Reported-by: Andy Whitcroft <apw@canonical.com>
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
when gsmtty_remove put dlci, it will cause memory leak if dlci->port's refcount is zero.
So we do the cleanup work in .cleanup callback instead.
dlci will be last put in two call chains.
1) gsmld_close -> gsm_cleanup_mux -> gsm_dlci_release -> dlci_put
2) gsmld_remove -> dlci_put
so there is a race. the memory leak depends on the race.
In call chain 2. we hit the memory leak. below comment tells.
release_tty -> tty_driver_remove_tty -> gsmtty_remove -> dlci_put -> tty_port_destructor (WARN_ON(port->itty) and return directly)
|
tty->port->itty = NULL;
|
tty_kref_put ---> release_one_tty -> gsmtty_cleanup (added by our patch)
So our patch fix the memory leak by doing the cleanup work after tty core did.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Fixes: dfabf7ffa30585
Cc: stable <stable@vger.kernel.org> # 3.14+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Avoton AHCI occasionally sees drive probe timeouts at driver load time.
When this happens SCR_STATUS indicates device detected, but no D2H FIS
reception. Reset the internal link state machines by bouncing
port-enable in the PCS register when this occurs.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Without this flag some versions of these enclosures do not work.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Christian Schaller <cschalle@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix regression introduced by commit <29ef8a53542a>. After it writing
AT commands to /dev/GCT-ATM0 is unsuccessful (no echo, no response)
and dmesg show "gdmtty: invalid payload : 1 16 f011".
Before that commit value of dummy_cnt was only a padding size. After using
ALIGN() this value is increased by its first argument. So the following
usage of this variable needs correction.
Signed-off-by: Sławomir Demeszko <s.demeszko@wireless-instruments.com>
Cc: stable <stable@vger.kernel.org> # 3.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes: f7d11e93ee97a locking,arch,arc: Fold atomic_ops
Cc: <stable@kernel.vger.org> # 3.18
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Since these are now visible to userspace it is nice to be consistent
with BSD (sys/netmpls/mpls.h in netBSD).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-05-07
This series contains updates to igb only.
Toshiaki provides two fixes for igb, first fixes an issue when changing
the number of rings by ethtool which causes oops because of uninitialized
pointers. The second fix resolves a typo where tx_ring was used instead
of the desired rx_ring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few patches have come up since the merge window. The largest one is
a rewrite of the PXA lubbock/mainstone IRQ handling. This was already
broken in 2011 by a change to the GPIO code and only noticed now.
The other changes contained here are:
MAINTAINERS file updates:
- Ray Jui and Scott Branden are now co-maintainers for some of the
mach-bcm chips, while Christian Daudt and Marc Carino have stepped
down.
- Andrew Victor is no longer maintaining at91. Instead, Alexandre
Belloni now becomes an official maintainer, after having done a
bulk of the work for a while.
- Baruch Siach, who added the mach-digicolor platform in 4.1 is now
listed as maintainer
- The git URL for mach-socfpga has changed
Bug fixes:
- Three bug fixes for new rockchip rk3288 code
- A regression fix to make SD card support work on certain ux500
boards
- multiple smaller dts fixes for imx, omap, mvebu, and shmobile
- a regression fiix for omap3 power consumption
- a fix for regression in the ARM CCI bus driver
Configuration changes:
- more imx platforms are now enabled in multi_v7_defconfig"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
MAINTAINERS: Update brcmstb entry
MAINTAINERS: Remove Christian Daudt for mach-bcm
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user-namespace fix from Eric Biederman:
"Eric Windish recently reported a really bug that allows mounting fresh
copies of proc and sysfs when it really should not be allowed. The
code attempted to verify that proc and sysfs were fully visible but
there is a test missing to ensure that the root of the filesystem is
visible. Doh!
The following patch fixes that.
This fixes a containment issue that the docker folks are seeing"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
mnt: Fix fs_fully_visible to verify the root directory is visible
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Two patches from the irq departement:
- a simple fix to make dummy_irq_chip usable for wakeup scenarios
- removal of the gic arch_extn hackery. Now that all users are
converted we really want to get rid of the interface so people wont
come up with new use cases"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: gic: Drop support for gic_arch_extn
genirq: Set IRQCHIP_SKIP_SET_WAKE flag for dummy_irq_chip
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A simple fix to actually shut down a detached device instead of
keeping it active"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Shutdown detached clockevent device
|
|
transfer_buffer_length is of type u32. It's therefore wrong to assign it
to a signed integer. This patch avoids the overflow.
It's worth noting that entry->length here is a long; perhaps it would be
beneficial at somepoint to change this to be unsigned as well, if
nothing else relies on its signedness for error conditions or the like.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch should have been part of the previous patch having the
same summary. See http://marc.info/?l=linux-kernel&m=143039470103795&w=2
Unfortunately, I didn't check to see where else this lock was used before
submitting that patch. This should take care of it for netxen_nic, as I
did a thorough search this time.
To recap from the original patch; although testing this driver with
DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled did not produce any traces,
it would be more prudent in the case of tx_clean_lock to use _bh
versions of spin_[un]lock, since this lock is manipulated in both
the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Acked-By: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xgene_enet driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The amd-xgbe driver currently only works with the Seattle SoC, which
is ARM64 architecture, so there is no point in building this driver on
other architectures except for build testing purpose. The dependency
list can be updated later if the driver ever supports other
architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tcf_destroy() returns true, tp could be already destroyed,
we should not use tp->next after that.
For long term, we probably should move tp list to list_head.
Fixes: 1e052be69d04 ("net_sched: destroy proto tp when all filters are gone")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This device is sold as 'Lenovo OneLink Pro Dock'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same hardware issue the at91 must work around applies to at least the
Zynq ethernet, and possibly more devices. The driver also needs to handle
the RXUBR interrupt since it turns it on with MACB_RX_INT_FLAGS anyway.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sowmini Varadhan says:
====================
net/rds: RDS-TCP robustness fixes
This patch-set contains bug fixes for state-recovery at the RDS
layer when the underlying transport is TCP and the TCP state at one
of the endpoints is reset
V2 changes: DaveM comments to reduce memory footprint, follow
NFS/RPC model where possible. Added test-case #3
Without the changes in this set, when one of the endpoints is reset,
the existing code does not correctly clean up RDS socket state for stale
connections, resulting in some unstable, timing-dependant behavior on
the wire, including an infinite exchange of 3WHs back-and-forth, and a
resulting potential to never converge RDS state.
Test cases used to verify the changes in this set are:
1. Start rds client/server applications on two participating nodes,
node1 and node2. After at least one packet has been sent (to establish
the TCP connection), restart the rds_tcp module on the client, and
now resend packets. Tcpdump should show server sending a FIN for the
"old" client port, and clean connection establishment/exchange for
the new client port.
2. At the end of step 1, restart rds srever on node2, and start client on
node1, make sure using tcpdump, 'netstat -an|grep 16385' that
packets flow correctly.
3. start RDS client/server application on two participating nodes, and
repeat steps 1 and 2, but this time, simulate node failure by doing
"ifconfig <intf> down", so no FIN is sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the peer of an RDS-TCP connection restarts, a reconnect
attempt should only be made from the active side of the TCP
connection, i.e. the side that has a transient TCP port
number. Do not add the passive side of the TCP connection
to the c_hash_node and thus avoid triggering rds_queue_reconnect()
for passive rds connections.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running RDS over TCP, the active (client) side connects to the
listening ("passive") side at the RDS_TCP_PORT. After the connection
is established, if the client side reboots (potentially without even
sending a FIN) the server still has a TCP socket in the esablished
state. If the server-side now gets a new SYN comes from the client
with a different client port, TCP will create a new socket-pair, but
the RDS layer will incorrectly pull up the old rds_connection (which
is still associated with the stale t_sock and RDS socket state).
This patch corrects this behavior by having rds_tcp_accept_one()
always create a new connection for an incoming TCP SYN.
The rds and tcp state associated with the old socket-pair is cleaned
up via the rds_tcp_state_change() callback which would typically be
invoked in most cases when the client-TCP sends a FIN on TCP restart,
triggering a transition to CLOSE_WAIT state. In the rarer event of client
death without a FIN, TCP_KEEPALIVE probes on the socket will detect
the stale socket, and the TCP transition to CLOSE state will trigger
the RDS state cleanup.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are only IPv6 source specific default routes present, the
host gets -ENETUNREACH on e.g. connect() because ip6_dst_lookup_tail
calls ip6_route_output first, and given source address any, it fails,
and ip6_route_get_saddr is never called.
The change is to use the ip6_route_get_saddr, even if the initial
ip6_route_output fails, and then doing ip6_route_output _again_ after
we have appropriate source address available.
Note that this is '99% fix' to the problem; a correct fix would be to
do route lookups only within addrconf.c when picking a source address,
and never call ip6_route_output before source address has been
populated.
Signed-off-by: Markus Stenberg <markus.stenberg@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
