| Age | Commit message (Collapse) | Author |
|---|
|
Add pinctrl bindings for Actions Semi S900 SoC
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.17
- Add DU and VIN pin groups on R-Car D3,
- Add HDMI, TMU, and VIN pin groups on R-Car H3 and M3-W,
- Add support for the new R-Car M3-N SoC,
- Small fixes and cleanups.
|
|
Systems that don't have devicetree need pinctrl_register_mappings.
It should be EXPORT_SYMBOL_GPL so that it can be called from
pinctrl drivers built as modules.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Meson8b is a cost reduced variant of the Meson8 SoC. It's package size
is smaller than Meson8.
Unfortunately there are a few key differences which cannot be seen
without close inspection of the code and the public S805 datasheet:
- the GPIOX bank is missing the GPIOX_12, GPIOX_13, GPIOX_14 and
GPIOX_15 GPIOs
- the GPIOY bank is missing the GPIOY_2, GPIOY_4, GPIOY_5, GPIOY_15 and
GPIOY_16 GPIOs
- the GPIODV bank is missing all GPIOs except GPIODV_9, GPIODV_24,
GPIODV_25, GPIODV_26, GPIODV_27, GPIODV_28 and GPIODV_29
- the GPIOZ bank is missing completely
- there is a new GPIO bank called "DIF"
This means that Meson8b only has 83 actual GPIO lines. Without any holes
there would be 130 GPIO lines in total (120 are inherited from Meson8
plus 10 new from the DIF bank).
GPIOs greater GPIOZ_3 (whose ID is 83 - as a reminder: this is exactly
the number of actual GPIO lines on Meson8b and also the value of
meson8b_cbus_pinctrl_data.num_pins) cannot berequested. Using CARD_6
(which used ID 100 prior to this patch, "base of the GPIO controller was
382) as an example:
$ echo 482 > /sys/class/gpio/export
export_store: invalid GPIO 482
This removes all non-existing pins from to dt-bindings header file
(include/dt-bindings/gpio/meson8b-gpio.h). This allows us to have a
consecutive numbering for the GPIO #defines (GPIOY_2 doesn't exist for
example, so previously the GPIOY_3 ID was "GPIOY_1 + 2", after this
patch it is "GPIOY_1 + 1"). As a nice side-effect this means that we get
compile-time (instead of runtime) errors if Meson8b .dts uses a pin that
only exists on Meson8.
Additionally the pinctrl-meson8b driver has to be updated to handle this
new GPIO numbering. By default a struct meson_bank only handles GPIO
banks where the pins are numbered consecutively because it calculates
the bit offsets based on the GPIO IDs.
This is solved by taking the original BANK() definition and splitting it
into consecutive subsets (X0..11 and X16..21). The bit offsets for each
new bank includes the skipped GPIOs (the definition of the "X0..11" bank
is identical to the old "X" bank apart from the "last IRQ" field, the
definition of the new, split "X16..21" bank takes the original "X" bank
and adds 16 - the start of the new split bank - to the "first IRQ",
pullen bit, pull bit, dir bit, out bit and in bit).
Commit 984cffdeaeb7ea ("pinctrl: Fix gpio/pin mapping for Meson8b")
fixed the same issue by setting "ngpio" (of the gpio_chip) to 130.
Unfortunately this broke in db80f0e158e621 ("pinctrl: meson: get rid of
unneeded domain structures").
The solution from this patch was considered to be better than the
previous attempt at fixing this because it provides compile-time error
checking for the GPIOs that exist on Meson8 but don't exist on Meson8b.
The following pins were tested on an Odroid-C1 using the sysfs GPIO
interface checking that their value (high or low) could be read:
- GPIOX_0, GPIOX_1, GPIOX_2, GPIOX_3, GPIOX_4, GPIOX_5, GPIOX_6,
GPIOX_7, GPIOX_8, GPIOX_9, GPIOX_10, GPIOX_11, GPIOX_18, GPIOX_19,
GPIOX_20, GPIOX_21
- GPIOY_3, GPIOY_7, GPIOY_8
(some of these had to be pulled up because they were low by default,
others were high by default so these had to be pulled down)
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When dt_to_map_one_config() is called with a pinctrl_dev passed
in, it should only be using this if the node being looked up
is a hog. The code was always using the passed pinctrl_dev
without checking whether the dt node referred to it.
A pin controller can have pinctrl-n dependencies on other pin
controllers in these cases:
- the pin controller hardware is external, for example I2C, so
needs other pin controller(s) to be setup to communicate with
the hardware device.
- it is a child of a composite MFD so its of_node is shared with
the parent MFD and other children of that MFD. Any part of that
MFD could have dependencies on other pin controllers.
Because of this, dt_to_map_one_config() can't assume that if it
has a pinctrl_dev passed in then the node it looks up must be
a hog. It could be a reference to some other pin controller.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing pinctrl binding about I2C2 and SPI2 which would be used in
devicetree related files.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It should be good that no use "_" is in examples. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-gpio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
- removes unneeded irq_chip.irq_eoi callback
- adds irq_chip.irq_set_wake callback for possible
in the future GPIO wakeup
- adds irq_chip.irq_ack callback
Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add group configuration for uarts that are cut down
variants, the standard being full, i.e. all signals,
flow control, i.e. rx/tx and cts/rts, and rx/tx only.
This allows us to be more precise in which pins we're
actually using.
Unfortunately the existing naming scheme leaves things
to be desired, e.g. uart3grp0 means RX/TX and CTS/RTS,
yet uart0grp0 means all pins.
Since the exising suffixes have different meaning for
different uarts, and the fact that we cannot change
the name of existing groups, makes it hard to use a
descriptive name for the newly added groups.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing pin group uart5nocts (all pins except cts), which has been
supported by the artpec6 pinctrl driver since its initial submission.
Fixes: 00df0582eab1 ("pinctrl: Add pincontrol driver for ARTPEC-6 SoC")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add group configuration for uarts that are cut down
variants, the standard being full, i.e. all signals,
flow control, i.e. rx/tx and cts/rts, and rx/tx only.
This allows us to be more precise in which pins we're
actually using.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that arch/metag/ has been removed, along with TZ1090 SoC support,
remove the TZ1090 pinctrl drivers. They are of no value without the
architecture and SoC platform code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Most pins on the R8A77965 SoC can be configured in GPIO mode for
interrupt and GPIO functionality, while a couple of them can also
be routed to the INTC-EX hardware block (formerly known as IRQC).
On R8A77965 the INTC-EX hardware handles pins IRQ0 -> IRQ5 and
this patch adds support for them to the PFC driver as "intc_ex_irqN".
Based on a similar patch for the R8A7795 PFC driver by Magnus Damm
<damm+renesas@opensource.se>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds VIN4 pins, groups and function for the
R8A77995 (D3) SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds VIN4 and VIN5 pins, groups and functions for the
R8A7795 SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds VIN4 and VIN5 pins, groups and functions for the
R8A7796 SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The mcp23s08 series device can be configured for wired and interrupts
using an external pull-up and open drain output via the IOCON_ODR bit.
And "drive-open-drain" property to enable this.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This flag set the mcp23s08 device irq type to open drain active low.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
one_regmap_config is always null if mcp type is MCP_TYPE_S18.
Remove the null check so that the mcp23s18 will probe.
Fixes: 1781af563aef66c2eb7cda ("pinctrl: mcp23s08: spi: Fix duplicate pinctrl debugfs entries")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On boot, gpiochip_add_data() initializes the FLAG_IS_OUT bit in
desc->flags iff its gpio_chip does not have ->direction_input() handler,
else it is initialized to 0, which implies the GPIO is an "input".
Later, the sysfs "direction" handler will use gpiod_get_direction() to
get the current direction, but if no ->get_direction() handler is
installed, the result will just be the current (initial) value of flags,
which will always be OUT irregardless of the initial register value.
Add a get_direction() handler to pinctrl-amd to fix this and always
provide the correct value for direction.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The function ocelot_pinctrl_probe is local to the source and does not
need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/pinctrl/pinctrl-ocelot.c:465:5: warning: symbol
'ocelot_pinctrl_probe' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EtherAVB groups and functions definitions for R-Car M3-N.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add SCIF[0-5] groups and pin function definitions for R-Car M3-N.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add initial PFC support for R-Car M3-N (r8a77965) SoC.
No groups or functions defined, just pin and registers enumeration.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7795 ES1.x SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds HDMI0 CEC pin, group and function to the R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds HDMI0 CEC pin, group and function to
the R8A7795 ES1.x SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: fixed typo in comment]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds HDMI0 CEC pin, group and function to the R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: fixed typo in comment]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
NDFC pins group
This patch fixes to set IPSR and MOD_SEL when using NFDATA{14,15}_A and
NF{RB,WP}_N_A pin function is selected. And renamess MOD_SEL2 bit22 value
definition name to SEL_NDFC.
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.53E.
Fixes: f9aece7344bd ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch fixes MOD_SEL1 bit20 and MOD_SEL2 bit20, bit21 pin assignment
for SSI pins group.
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch fixes MOD_SEL1 bit20 and MOD_SEL2 bit20, bit21 pin assignment
for SSI pins group.
This is a correction because MOD_SEL register specification for R8A7795
ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E.
Fixes: b205914c8f82 ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds DU pins, groups and function for the R8A77995 (D3) SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The MUSB block in the Nomadik has two pin settings: high speed or
full speed. These correspond to two unique pin group settings: all
pins set to function B for high speed and all set to function C
for full speed. Full speed uses more pins than high speed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
R8A7778 is R-Car (not R-Mobile) M1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The base of the TLMM gpiochip should not be statically defined as 0, fix
this to not artificially restrict the existence of multiple pinctrl-msm
devices.
Fixes: f365be092572 ("pinctrl: Add Qualcomm TLMM driver")
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a bit more involved because the pinctrl core so far always
assumed that one device (with a unique dev_name) only contains a single
pinctrl thing. This is not true for the mcp23s08 driver for chips
connected over SPI. They have a "logical address" which means that
several chips can share one physical CS signal.
A downside of this patch are some possibly ugly names for the debugfs
entries, such as "spi1.1-mcp23xxx-pinctrl.2", etc.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When several devices are sharing one hardware SPI CS, there is no visual
clue in `lsgpio` or in /sys/kernel/debug/gpio about which one is which
one. Stuff depends on the enumeration order, and therefore lower chip
addresses always go first, but that's just an implementation detail.
This change includes the device-specific address in the debug output:
gpiochip4: GPIOs 464-479, parent: spi/spi1.1, mcp23s17.2, can sleep:
gpiochip3: GPIOs 480-495, parent: spi/spi1.1, mcp23s17.1, can sleep:
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The SPI version of this chip allows several devices to be present on the
same SPI bus via a local address. If this is in action and if the kernel
has debugfs, however, the code attempts to create duplicate entries for
the regmap's debugfs:
mcp23s08 spi1.1: Failed to create debugfs directory
This patch simply assigns a local name matching the device logical
address to the `struct regmap_config`.
No changes are needed for MCP23S18 because that device does not support
any logical addressing. Similarly, I2C devices do not need any action,
either, because they are already different in their I2C address.
A similar problem is present for the pinctrl debugfs instance, but that
one is not addressed by this patch.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the pinctrl definitions for the TLMM of SDM845.
Signed-off-by: Kyle Yan <kyan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the DeviceTree binding for the Qualcomm SDM845 TLMM block.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
except, again, POLLFREE and POLL_BUSY_LOOP.
With this, we finally get to the promised end result:
- POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
stray instances of ->poll() still using those will be caught by
sparse.
- eventpoll.c and select.c warning-free wrt __poll_t
- no more kernel-side definitions of POLL... - userland ones are
visible through the entire kernel (and used pretty much only for
mangle/demangle)
- same behavior as after the first series (i.e. sparc et.al. epoll(2)
working correctly).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more poll annotation updates from Al Viro:
"This is preparation to solving the problems you've mentioned in the
original poll series.
After this series, the kernel is ready for running
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
as a for bulk search-and-replace.
After that, the kernel is ready to apply the patch to unify
{de,}mangle_poll(), and then get rid of kernel-side POLL... uses
entirely, and we should be all done with that stuff.
Basically, that's what you suggested wrt KPOLL..., except that we can
use EPOLL... instead - they already are arch-independent (and equal to
what is currently kernel-side POLL...).
After the preparations (in this series) switch to returning EPOLL...
from ->poll() instances is completely mechanical and kernel-side
POLL... can go away. The last step (killing kernel-side POLL... and
unifying {de,}mangle_poll() has to be done after the
search-and-replace job, since we need userland-side POLL... for
unified {de,}mangle_poll(), thus the cherry-pick at the last step.
After that we will have:
- POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of
->poll() still using those will be caught by sparse.
- eventpoll.c and select.c warning-free wrt __poll_t
- no more kernel-side definitions of POLL... - userland ones are
visible through the entire kernel (and used pretty much only for
mangle/demangle)
- same behavior as after the first series (i.e. sparc et.al. epoll(2)
working correctly)"
* 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
annotate ep_scan_ready_list()
ep_send_events_proc(): return result via esed->res
preparation to switching ->poll() to returning EPOLL...
add EPOLLNVAL, annotate EPOLL... and event_poll->event
use linux/poll.h instead of asm/poll.h
xen: fix poll misannotation
smc: missing poll annotations
|
|
Pull xtense fix from Max Filippov:
"Build fix for xtensa architecture with KASAN enabled"
* tag 'xtensa-20180211' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix build with KASAN
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2
Pull nios2 update from Ley Foon Tan:
- clean up old Kconfig options from defconfig
- remove leading 0x and 0s from bindings notation in dts files
* tag 'nios2-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: defconfig: Cleanup from old Kconfig options
nios2: dts: Remove leading 0x and 0s from bindings notation
|
