| Age | Commit message (Collapse) | Author |
|---|
|
Sudarsana Reddy Kalluru says:
====================
net: atlantic: 11-2021 fixes
The patch series contains fixes for atlantic driver to improve support
of latest AQC113 chipset.
Please consider applying it to 'net' tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the warn trace message - it's not a correct check here, because
the function can still be called on the device in DOWN state
Fixes: 508f2e3dce454 ("net: atlantic: split rx and tx per-queue stats")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
B0 is the main and widespread device revision of atlantic2 HW. In the
current state, driver will incorrectly fetch the statistics for this
revision.
Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since Half Duplex mode has been deprecated by the firmware, driver should
not advertise Half Duplex speed in ethtool support link speed values.
Fixes: 071a02046c262 ("net: atlantic: A2: half duplex support")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.
Fixes: b3f0c79cba206 ("net: atlantic: A2 hw_ops skeleton")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The correct way to reflect firmware version is to use bundle version.
Hence populating the same instead of MAC fw version.
Fixes: c1be0bf092bd2 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.
Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.
Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our current code is supposed to serialise the commits by waiting for all
the drm_crtc_commits associated to the previous HVS state.
However, assuming we have two CRTCs running and being configured and we
configure each one alternately, we end up in a situation where we're
not waiting at all.
Indeed, starting with a state (state 0) where both CRTCs are running,
and doing a commit (state 1) on the first CRTC (CRTC 0), we'll associate
its commit to its assigned FIFO in vc4_hvs_state.
If we get a new commit (state 2), this time affecting the second CRTC
(CRTC 1), the DRM core will allow both commits to execute in parallel
(assuming they don't have any share resources).
Our code in vc4_atomic_commit_tail is supposed to make sure we only get
one commit at a time and serialised by order of submission. It does so
by using for_each_old_crtc_in_state, making sure that the CRTC has a
FIFO assigned, is used, and has a commit pending. If it does, then we'll
wait for the commit before going forward.
During the transition from state 0 to state 1, as our old CRTC state we
get the CRTC 0 state 0, its commit, we wait for it, everything works fine.
During the transition from state 1 to state 2 though, the use of
for_each_old_crtc_in_state is wrong. Indeed, while the code assumes it's
returning the state of the CRTC in the old state (so CRTC 0 state 1), it
actually returns the old state of the CRTC affected by the current
commit, so CRTC 0 state 0 since it wasn't part of state 1.
Due to this, if we alternate between the configuration of CRTC 0 and
CRTC 1, we never actually wait for anything since we should be waiting
on the other every time, but it never is affected by the previous
commit.
Change the logic to, at every commit, look at every FIFO in the previous
HVS state, and if it's in use and has a commit associated to it, wait
for that commit.
Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-7-maxime@cerno.tech
|
|
Our HVS global state, when duplicated, will also copy the pointer to the
drm_crtc_commit (and increase the reference count) for each FIFO if the
pointer is not NULL.
However, our atomic_setup function will overwrite that pointer without
putting the reference back leading to a memory leak.
Since the commit is only relevant during the atomic commit process, it
doesn't make sense to duplicate the reference to the commit anyway.
Let's remove it.
Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-6-maxime@cerno.tech
|
|
Commit 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a
commit") introduced a wait on the previous commit done on a given HVS
FIFO.
However, we never cleared that pointer once done. Since
drm_crtc_commit_put can free the drm_crtc_commit structure directly if
we were the last user, this means that it can lead to a use-after free
if we were to duplicate the state, and that stale pointer would even be
copied to the new state.
Set the pointer to NULL once we're done with the wait so that we don't
carry over a pointer to a free'd structure.
Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-5-maxime@cerno.tech
|
|
Commit 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a
commit") introduced a global state for the HVS, with each FIFO storing
the current CRTC commit so that we can properly synchronize commits.
However, the refcounting was off and we thus ended up leaking the
drm_crtc_commit structure every commit. Add a drm_crtc_commit_put to
prevent the leakage.
Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-4-maxime@cerno.tech
|
|
The HVS global state functions return an error pointer, but in most
cases we check if it's NULL, possibly resulting in an invalid pointer
dereference.
Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-3-maxime@cerno.tech
|
|
Several DRM/KMS atomic commits can run in parallel if they affect
different CRTC. These commits share the global HVS state, so we have
some code to make sure we run commits in sequence. This synchronization
code is one of the first thing that runs in vc4_atomic_commit_tail().
Another constraints we have is that we need to make sure the HVS clock
gets a boost during the commit. That code relies on clk_set_min_rate and
will remove the old minimum and set a new one. We also need another,
temporary, minimum for the duration of the commit.
The algorithm is thus to set a temporary minimum, drop the previous
one, do the commit, and finally set the minimum for the current mode.
However, the part that sets the temporary minimum and drops the older
one runs before the commit synchronization code.
Thus, under the proper conditions, we can end up mixing up the minimums
and ending up with the wrong one for our current step.
To avoid it, let's move the clock setup in the protected section.
Fixes: d7d96c00e585 ("drm/vc4: hvs: Boost the core clock during modeset")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-2-maxime@cerno.tech
|
|
kernel test robot reported that RCU stall via printk() flooding is
possible [1] when stress testing.
Link: https://lkml.kernel.org/r/20211129073709.GA18483@xsang-OptiPlex-9020 [1]
Reported-by: kernel test robot <oliver.sang@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When link modes were initially added in commit 2c762679435dc
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc78d0eb
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.
Switch to using more specific link modes added in commit 5711a98221443
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Tested with MCX311A-XCAT connected via DAC.
Before:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseKX/Full
10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
With this change:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Signed-off-by: Erik Ekman <erik@kryo.se>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In our test device, we're currently freeing skbs in the transmit path
with kfree(), rather than kfree_skb(). This change uses the correct
kfree_skb() instead.
Fixes: ded21b722995 ("mctp: Add test utils")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the TLS cipher suite uses CCM mode, including AES CCM and
SM4 CCM, the first byte of the B0 block is flags, and the real
IV starts from the second byte. The XOR operation of the IV and
rec_seq should be skip this byte, that is, add the iv_offset.
Fixes: f295b3ae9f59 ("net/tls: Add support of AES128-CCM based ciphers")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Cc: Vakul Garg <vakul.garg@nxp.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Benjamin Poirier says:
====================
net: mpls: Netlink notification fixes
fix missing or inaccurate route notifications when devices used in
nexthops are deleted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the previous commit, nh_dev can no longer be accessed and
modified concurrently.
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are various problems related to netlink notifications for mpls route
changes in response to interfaces being deleted:
* delete interface of only nexthop
DELROUTE notification is missing RTA_OIF attribute
* delete interface of non-last nexthop
NEWROUTE notification is missing entirely
* delete interface of last nexthop
DELROUTE notification is missing nexthop
All of these problems stem from the fact that existing routes are modified
in-place before sending a notification. Restructure mpls_ifdown() to avoid
changing the route in the DELROUTE cases and to create a copy in the
NEWROUTE case.
Fixes: f8efb73c97e2 ("mpls: multipath route support")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
is available
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes: cc89c323a30e ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71
Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch family can have up to 8 UTP ports {0..7}. However,
INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK was using 2 bits instead of 3,
dropping the most significant bit during indirect register reads and
writes. Reading or writing ports 4, 5, 6, and 7 registers was actually
manipulating, respectively, ports 0, 1, 2, and 3 registers.
This is not sufficient but necessary to support any variant with more
than 4 UTP ports, like RTL8367S.
rtl8365mb_phy_{read,write} will now returns -EINVAL if phy is greater
than 7.
Fixes: 4af2950c50c8 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Steffen reported a TCP stream corruption for HTTP requests
served by the apache web-server using a cifs mount-point
and memory mapping the relevant file.
The root cause is quite similar to the one addressed by
commit 20eb4f29b602 ("net: fix sk_page_frag() recursion from
memory reclaim"). Here the nested access to the task page frag
is caused by a page fault on the (mmapped) user-space memory
buffer coming from the cifs file.
The page fault handler performs an smb transaction on a different
socket, inside the same process context. Since sk->sk_allaction
for such socket does not prevent the usage for the task_frag,
the nested allocation modify "under the hood" the page frag
in use by the outer sendmsg call, corrupting the stream.
The overall relevant stack trace looks like the following:
httpd 78268 [001] 3461630.850950: probe:tcp_sendmsg_locked:
ffffffff91461d91 tcp_sendmsg_locked+0x1
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139814e sock_sendmsg+0x3e
ffffffffc06dfe1d smb_send_kvec+0x28
[...]
ffffffffc06cfaf8 cifs_readpages+0x213
ffffffff90e83c4b read_pages+0x6b
ffffffff90e83f31 __do_page_cache_readahead+0x1c1
ffffffff90e79e98 filemap_fault+0x788
ffffffff90eb0458 __do_fault+0x38
ffffffff90eb5280 do_fault+0x1a0
ffffffff90eb7c84 __handle_mm_fault+0x4d4
ffffffff90eb8093 handle_mm_fault+0xc3
ffffffff90c74f6d __do_page_fault+0x1ed
ffffffff90c75277 do_page_fault+0x37
ffffffff9160111e page_fault+0x1e
ffffffff9109e7b5 copyin+0x25
ffffffff9109eb40 _copy_from_iter_full+0xe0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139815c sock_sendmsg+0x4c
ffffffff913981f7 sock_write_iter+0x97
ffffffff90f2cc56 do_iter_readv_writev+0x156
ffffffff90f2dff0 do_iter_write+0x80
ffffffff90f2e1c3 vfs_writev+0xa3
ffffffff90f2e27c do_writev+0x5c
ffffffff90c042bb do_syscall_64+0x5b
ffffffff916000ad entry_SYSCALL_64_after_hwframe+0x65
The cifs filesystem rightfully sets sk_allocations to GFP_NOFS,
we can avoid the nesting using the sk page frag for allocation
lacking the __GFP_FS flag. Do not define an additional mm-helper
for that, as this is strictly tied to the sk page frag usage.
v1 -> v2:
- use a stricted sk_page_frag() check instead of reordering the
code (Eric)
Reported-by: Steffen Froemer <sfroemer@redhat.com>
Fixes: 5640f7685831 ("net: use a per task frag allocator")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver assumes that split headers can be enabled/disabled without
stopping/starting the device, so it writes DMA_CHAN_CONTROL from
stmmac_set_features(). However, on my system (IP v5.10a without Split
Header support), simply writing DMA_CHAN_CONTROL when DMA is running
(for example, with the commands below) leads to a TX watchdog timeout.
host$ socat TCP-LISTEN:1024,fork,reuseaddr - &
device$ ethtool -K eth0 tso off
device$ ethtool -K eth0 tso on
device$ dd if=/dev/zero bs=1M count=10 | socat - TCP4:host:1024
<tx watchdog timeout>
Note that since my IP is configured without Split Header support, the
driver always just reads and writes the same value to the
DMA_CHAN_CONTROL register.
I don't have access to any platforms with Split Header support so I
don't know if these writes to the DMA_CHAN_CONTROL while DMA is running
actually work properly on such systems. I could not find anything in
the databook that says that DMA_CHAN_CONTROL should not be written when
the DMA is running.
But on systems without Split Header support, there is in any case no
need to call enable_sph() in stmmac_set_features() at all since SPH can
never be toggled, so we can avoid the watchdog timeout there by skipping
this call.
Fixes: 8c6fc097a2f4acf ("net: stmmac: gmac4+: Add Split Header support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
driver_detach
device_release_driver_internal
__device_release_driver
drv->remove(dev) --> platform_drv_remove/platform_remove
drv->remove(dev) --> sata_fsl_remove
iounmap(host_priv->hcr_base); <---- unmap
kfree(host_priv); <---- free
devres_release_all
release_nodes
dr->node.release(dev, dr->data) --> ata_host_stop
ap->ops->port_stop(ap) --> sata_fsl_port_stop
ioread32(hcr_base + HCONTROL) <---- UAF
host->ops->host_stop(host)
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
The zero day bot reported some sparse complaints in pata_falcon.c. E.g.
drivers/ata/pata_falcon.c:58:41: warning: cast removes address space '__iomem' of expression
drivers/ata/pata_falcon.c:58:41: warning: incorrect type in argument 1 (different address spaces)
drivers/ata/pata_falcon.c:58:41: expected unsigned short volatile [noderef] [usertype] __iomem *port
drivers/ata/pata_falcon.c:58:41: got unsigned short [usertype] *
The same thing shows up in 8 places, all told. Avoid this by removing
unnecessary type casts.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
As reported by Exuvo is possible that we have lot's of EPROTO errors
during device start i.e. firmware load. But after that device works
correctly. Hence marking device gone by few EPROTO errors done by
commit e383c70474db ("rt2x00: check number of EPROTO errors") caused
regression - Exuvo device stop working after kernel update. To fix
disable the check during device start.
Link: https://lore.kernel.org/linux-wireless/bff7d309-a816-6a75-51b6-5928ef4f7a8c@exuvo.se/
Reported-and-tested-by: Exuvo <exuvo@exuvo.se>
Fixes: e383c70474db ("rt2x00: check number of EPROTO errors")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111141003.GA134627@wp.pl
|
|
With the use of dummy events, we can drop virtgpu specific
behavior.
Fixes: cd7f5ca33585 ("drm/virtio: implement context init: add virtio_gpu_fence_event")
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Gurchetan Singh <gurchetansingh@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20211122232210.602-3-gurchetansingh@google.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
The current virtgpu implementation of poll(..) drops events
when VIRTGPU_CONTEXT_PARAM_POLL_RINGS_MASK is enabled (otherwise
it's like a normal DRM driver).
This is because paravirtualized userspaces receives responses in a
buffer of type BLOB_MEM_GUEST, not by read(..).
To be in line with other DRM drivers and avoid specialized behavior,
it is possible to define a dummy event for virtgpu. Paravirtualized
userspace will now have to call read(..) on the DRM fd to receive the
dummy event.
Fixes: b10790434cf2 ("drm/virtgpu api: create context init feature")
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Gurchetan Singh <gurchetansingh@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20211122232210.602-2-gurchetansingh@google.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
CBUS transfers have always been atomic, but after commit 63b96983a5dd
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5dd ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When running without MIO support, with pci=nomio or for devices which
are not MIO-capable the zPCI subsystem generates pseudo-MMIO addresses
to allow access to PCI BARs via MMIO based Linux APIs even though the
platform uses function handles and BAR numbers.
This is done by stashing an index into our global IOMAP array which
contains the function handle in the 16 most significant bits of the
addresses returned by ioremap() always setting the most significant bit.
On the other hand the MIO addresses assigned by the platform for use,
while requiring special instructions, allow PCI access with virtually
mapped physical addresses. Now the problem is that these MIO addresses
and our own pseudo-MMIO addresses may overlap, while functionally this
would not be a problem by itself this overlap is detected by common code
as both address types are added as resources in the iomem_resource tree.
This leads to the overlapping resource claim of either the MIO capable
or non-MIO capable devices with being rejected.
Since PCI is tightly coupled to the use of the iomem_resource tree, see
for example the code for request_mem_region(), we can't reasonably get
rid of the overlap being detected by keeping our pseudo-MMIO addresses
out of the iomem_resource tree.
Instead let's move the range used by our own pseudo-MMIO addresses by
starting at (1UL << 62) and only using addresses below (1UL << 63) thus
avoiding the range currently used for MIO addresses.
Fixes: c7ff0e918a7c ("s390/pci: deal with devices that have no support for MIO instructions")
Cc: stable@vger.kernel.org # 5.3+
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
For cs8409, it is required to run Jack Detect on resume.
Jack Detect on cs8409+cs42l42 requires an interrupt from
cs42l42 to be sent to cs8409 which is propogated to the driver
via an unsolicited event.
However, the hda_codec drops unsolicited events if the power_state
is not set to PMSG_ON. Which is set at the end of the resume call.
This means there is a race condition between setting power_state
to PMSG_ON and receiving the interrupt.
To solve this, we can add an API to set the power_state earlier
and call that before we start Jack Detect.
This does not cause issues, since we know inside our driver that
we are already initialized, and ready to handle the unsolicited
events.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v5.15+
Link: https://lore.kernel.org/r/20211128115558.71683-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Pull vhost,virtio,vdpa bugfixes from Michael Tsirkin:
"Misc fixes all over the place.
Revert of virtio used length validation series: the approach taken
does not seem to work, breaking too many guests in the process. We'll
need to do length validation using some other approach"
[ This merge also ends up reverting commit f7a36b03a732 ("vsock/virtio:
suppress used length validation"), which came in through the
networking tree in the meantime, and was part of that whole used
length validation series - Linus ]
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa_sim: avoid putting an uninitialized iova_domain
vhost-vdpa: clean irqs before reseting vdpa device
virtio-blk: modify the value type of num in virtio_queue_rq()
vhost/vsock: cleanup removing `len` variable
vhost/vsock: fix incorrect used length reported to the guest
Revert "virtio_ring: validate used buffer length"
Revert "virtio-net: don't let virtio core to validate used length"
Revert "virtio-blk: don't let virtio core to validate used length"
Revert "virtio-scsi: don't let virtio core to validate used buffer length"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 build fix from Thomas Gleixner:
"A single fix for a missing __init annotation of prepare_command_line()"
* tag 'x86-urgent-2021-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Mark prepare_command_line() __init
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"A single scheduler fix to ensure that there is no stale KASAN shadow
state left on the idle task's stack when a CPU is brought up after it
was brought down before"
* tag 'sched-urgent-2021-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/scs: Reset task stack state in bringup_cpu()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Thomas Gleixner:
"A single fix for perf to prevent it from sending SIGTRAP to another
task from a trace point event as it's not possible to deliver a
synchronous signal to a different task from there"
* tag 'perf-urgent-2021-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Ignore sigtrap for tracepoints destined for other tasks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two regression fixes for reader writer semaphores:
- Plug a race in the lock handoff which is caused by inconsistency of
the reader and writer path and can lead to corruption of the
underlying counter.
- down_read_trylock() is suboptimal when the lock is contended and
multiple readers trylock concurrently. That's due to the initial
value being read non-atomically which results in at least two
compare exchange loops. Making the initial readout atomic reduces
this significantly. Whith 40 readers by 11% in a benchmark which
enforces contention on mmap_sem"
* tag 'locking-urgent-2021-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem: Optimize down_read_trylock() under highly contended case
locking/rwsem: Make handoff bit handling more consistent
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull another tracing fix from Steven Rostedt:
"Fix the fix of pid filtering
The setting of the pid filtering flag tested the "trace only this pid"
case twice, and ignored the "trace everything but this pid" case.
The 5.15 kernel does things a little differently due to the new sparse
pid mask introduced in 5.16, and as the bug was discovered running the
5.15 kernel, and the first fix was initially done for that kernel,
that fix handled both cases (only pid and all but pid), but the
forward port to 5.16 created this bug"
* tag 'trace-v5.16-rc2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Test the 'Do not trace this pid' case in create event
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Intel VT-d fixes:
- Remove unused PASID_DISABLED
- Fix RCU locking
- Fix for the unmap_pages call-back
- Rockchip RK3568 address mask fix
- AMD IOMMUv2 log message clarification
* tag 'iommu-fixes-v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix unmap_pages support
iommu/vt-d: Fix an unbalanced rcu_read_lock/rcu_read_unlock()
iommu/rockchip: Fix PAGE_DESC_HI_MASKs for RK3568
iommu/amd: Clarify AMD IOMMUv2 initialization messages
iommu/vt-d: Remove unused PASID_DISABLED
|
|
Pull ksmbd fixes from Steve French:
"Five ksmbd server fixes, four of them for stable:
- memleak fix
- fix for default data stream on filesystems that don't support xattr
- error logging fix
- session setup fix
- minor doc cleanup"
* tag '5.16-rc2-ksmbd-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix memleak in get_file_stream_info()
ksmbd: contain default data stream even if xattr is empty
ksmbd: downgrade addition info error msg to debug in smb2_get_info_sec()
docs: filesystem: cifs: ksmbd: Fix small layout issues
ksmbd: Fix an error handling path in 'smb2_sess_setup()'
|
|
Use the architecture independent Kconfig option PAGE_SIZE_LESS_THAN_64KB
to indicate that VMXNET3 requires a page size smaller than 64kB.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
NTFS_RW code allocates page size dependent arrays on the stack. This
results in build failures if the page size is 64k or larger.
fs/ntfs/aops.c: In function 'ntfs_write_mst_block':
fs/ntfs/aops.c:1311:1: error:
the frame size of 2240 bytes is larger than 2048 bytes
Since commit f22969a66041 ("powerpc/64s: Default to 64K pages for 64 bit
book3s") this affects ppc:allmodconfig builds, but other architectures
supporting page sizes of 64k or larger are also affected.
Increasing the maximum frame size for affected architectures just to
silence this error does not really help. The frame size would have to
be set to a really large value for 256k pages. Also, a large frame size
could potentially result in stack overruns in this code and elsewhere
and is therefore not desirable. Make NTFS_RW dependent on page sizes
smaller than 64k instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Anton Altaparmakov <anton@tuxera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
NTFS_RW and VMXNET3 require a page size smaller than 64kB. Add generic
Kconfig option for use outside architecture code to avoid architecture
specific Kconfig options in that code.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Anton Altaparmakov <anton@tuxera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When creating a new event (via a module, kprobe, eprobe, etc), the
descriptors that are created must add flags for pid filtering if an
instance has pid filtering enabled, as the flags are used at the time the
event is executed to know if pid filtering should be done or not.
The "Only trace this pid" case was added, but a cut and paste error made
that case checked twice, instead of checking the "Trace all but this pid"
case.
Link: https://lore.kernel.org/all/202111280401.qC0z99JB-lkp@intel.com/
Fixes: 6cb206508b62 ("tracing: Check pid filtering when creating events")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Pull xfs fixes from Darrick Wong:
"Fixes for a resource leak and a build robot complaint about totally
dead code:
- Fix buffer resource leak that could lead to livelock on corrupt fs.
- Remove unused function xfs_inew_wait to shut up the build robots"
* tag 'xfs-5.16-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: remove xfs_inew_wait
xfs: Fix the free logic of state in xfs_attr_node_hasname
|
