| Age | Commit message (Collapse) | Author |
|---|
|
Though 8851BE is a 1x1 chip, but it has two antenna hardware module that
needs additional configuration to help choose antenna we are going to use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-3-pkshih@realtek.com
|
|
8851B hardware version A and B use different firmware, but register version
code of these two are the same, so add this helper to read efuse version to
determine which version is installed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-2-pkshih@realtek.com
|
|
clang warns about an unpacked structure inside of a packed one:
drivers/net/wireless/broadcom/b43/b43.h:654:4: error: field data within 'struct b43_iv' is less aligned than 'union (unnamed union at /home/arnd/arm-soc/drivers/net/wireless/broadcom/b43/b43.h:651:2)' and is usually due to 'struct b43_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
The problem here is that the anonymous union has the default alignment
from its members, apparently because the original author mixed up the
placement of the __packed attribute by placing it next to the struct
member rather than the union definition. As the struct itself is
also marked as __packed, there is no need to mark its members, so just
move the annotation to the inner type instead.
As Michael noted, the same problem is present in b43legacy, so
change both at the same time.
Acked-by: Michael Büsch <m@bues.ch>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/oe-kbuild-all/202305160749.ay1HAoyP-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516183442.536589-1-arnd@kernel.org
|
|
The Allwinner sunxi-mmc controller cannot handle word (16 bit)
transfers. So and sdio_{read,write}w fails with messages like the
following example using an RTL8822BS (but the same problems were also
observed with RTL8822CS and RTL8723DS chips):
rtw_8822bs mmc1:0001:1: Firmware version 27.2.0, H2C version 13
sunxi-mmc 4021000.mmc: unaligned scatterlist: os f80 length 2
sunxi-mmc 4021000.mmc: map DMA failed
rtw_8822bs mmc1:0001:1: sdio read16 failed (0x10230): -22
Use two consecutive single byte accesses for word operations instead. It
turns out that upon closer inspection this is also what the vendor
driver does, even though it does have support for sdio_{read,write}w. So
we can conclude that the rtw88 chips do support word access but only on
SDIO controllers that also support it. Since there's no way to detect if
the controller supports word access or not the rtw88 sdio driver
switches to the easiest approach: avoiding word access.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Closes: https://lore.kernel.org/linux-wireless/527585e5-9cdd-66ed-c3af-6da162f4b720@lwfinger.net/
Reported-by: Rudi Heitbaum <rudi@heitbaum.com>
Link: https://github.com/LibreELEC/LibreELEC.tv/pull/7837#issue-1708469467
Fixes: 65371a3f14e7 ("wifi: rtw88: sdio: Add HCI implementation for SDIO based chipsets")
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230515195043.572375-1-martin.blumenstingl@googlemail.com
|
|
When parse_pmsr_capa failed in hwsim_new_radio_nl, the memory resources
applied for by pmsr_capa are not released. Add release processing to the
incorrect path.
Fixes: 92d13386ec55 ("mac80211_hwsim: add PMSR capability support")
Reported-by: syzbot+904ce6fbb38532d9795c@syzkaller.appspotmail.com
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230515092227.2691437-1-shaozhengchao@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The rs_drv_get_rate flow reads the lq_sta to return the optimal rate
for tx frames. This read flow is not protected thereby leaving
a small window, a few instructions wide, open to contention by an
asynchronous rate update. Indeed this race condition was hit and the
update occurred in the middle of the read.
Fix this by locking the lq_sta struct during read.
Signed-off-by: Ariel Malamud <ariel.malamud@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.b52c9ed5c379.I15290b78e0d966c1b68278263776ca9de841d5fe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This bitmap equals to zero when in a non-MLO mode, and then we won't
be iterating on any link. Use for_each_sta_active_link() instead, as
it handles also the case of non-MLO mode.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.f32a8c08730a.Ib02248cd0b7f2bc885f91005c3c110dd027f9dcd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the firmware sends us a corrupted MCC response with
n_channels much larger than the command response can be,
we might copy far too much (uninitialized) memory and
even crash if the n_channels is large enough to make it
run out of the one page allocated for the FW response.
Fix that by checking the lengths. Doing a < comparison
would be sufficient, but the firmware should be doing
it correctly, so check more strictly.
Fixes: dcaf9f5ecb6f ("iwlwifi: mvm: add MCC update FW API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.d7b233139eb4.I51fd319df8e9d41881fc8450e83d78049518a79a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix a spelling mistake.
Fixes: 2856f623ce48 ("iwlwifi: mvm: Add list of OEMs allowed to use TAS")
Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.4090de6d1878.If9391ef6da78f1b2cc5eb6cb8f6965816bb7a7f5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix a spelling mistake.
Fixes: e8e10a37c51c ("iwlwifi: acpi: move ppag code from mvm to fw/acpi")
Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.fdd07f36a8bf.I223e5fb16ab5c95d504c3fdaffd0bd70affad1c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In iwl_mvm_mld_update_sta(), if the flow doesn't enter
for_each_sta_active_link(), the default value is returned.
Set this default to -EINVAL instead of 0 to better reflect
this.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.98b7e3aacf0b.I2fc274dd7e374ef7fac8e26d71c9cd73323da665@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
RCU protected fw_id_to_mac_id can be initialized with either
an error code or NULL. Thus, after dereferencing need to check
the value with IS_ERR_OR_NULL() and not only that it is not NULL.
Fix it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.ec5f2880e81c.Ifa8c0f451df2835bde800f5c3670cc46238a3bd8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The DBGI dump is (unsurprisingly) of type DBGI, not SRAM.
This leads to bad register accesses because the union is
built differently, there's no allocation ID, and thus the
allocation ID ends up being 0x8000.
Note that this was already wrong for DRAM vs. SMEM since
they use different parts of the union, but the allocation
ID is at the same place, so it worked.
Fix all of this but set the allocation ID in a way that
the offset calculation ends up without any offset.
Fixes: 34bc27783a31 ("iwlwifi: yoyo: fix DBGI_SRAM ini dump header.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.19a302ae4c65.I12272599f7c1930666157b9d5e7f81fe9ec4c421@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The concurrent link checks need to correctly differentiate
between AP and non-AP, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.992b2f981ef6.I7d386c19354e9be39c4822f436dd22c93422b660@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Lockdep points out that we can deadlock here by calling
cancel_delayed_work_sync() because that might be already
running and gotten interrupted by the NAPI soft-IRQ.
Even just calling something that can sleep is wrong in
this context though.
Luckily, it doesn't even really matter since the things
we need to do are idempotent, so just drop the _sync().
Fixes: e5d153ec54f0 ("iwlwifi: mvm: fix CSA AP side")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.b1813c823b4d.I9d20cc06d24fa40b6774d3dd95ea5e2bf8dd015b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We don't need to (and shouldn't) initialize the spinlock
during HW restart that was already initialized, so move
that into the correct if block. Since then we have two
consecutive if statements with the same (though inverted)
condition, unify those as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.221c22cfdf4e.I2e30113ef4bd8cb5bd9e1a69e52a95671914961c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are some assertions in the STA removal code that can
fail, and in that case we may leak memory since we skip
the freeing.
Fix this by freeing the dup_data earlier in the function,
we already have a check for when we free the station, and
this we don't need to do it with and without MLD API, so
it's a win all around.
Fixes: a571f5f635ef ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.173938681d72.Iff4b55fc52943825d6e3e28d78a24b155ea5cd22@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When we allocate a new channel context, or find an existing one
that is compatible, we currently assign it to a link before its
mindef is updated. This leads to strange situations, especially
in link switching where you switch to an 80 MHz link and expect
it to be active immediately, but the mindef is still configured
to 20 MHz while assigning. Also, it's strange that the chandef
passed to the assign method's argument is wider than the one in
the context.
Fix this by calculating the mindef with the new link considered
before calling the driver.
In particular, this fixes an iwlwifi problem during link switch
where the firmware would assert because the (link) station that
was added for the AP is configured to transmit at a bandwidth
that's wider than the channel context that it's configured on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-5-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When a chanctx is reserved for a new vif and we recalculate
the minimal definition for it, we need to consider the new
interface it's being reserved for before we assign it, so it
can be used directly with the correct min channel width.
Fix the code to - optionally - consider that, and use that
option just before doing the reassignment.
Also, when considering channel context reservations, we
should only consider the one link we're currently working with.
Change the boolean argument to a link pointer to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-4-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no need to call ieee80211_recalc_chanctx_min_def()
since it cannot and won't call the driver anyway; just use
_ieee80211_recalc_chanctx_min_def() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-3-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When stopping the AP, there might be a color change in progress. It
should be deactivated here, or the driver might later finalize a color
change on a stopped AP.
Fixes: 5f9404abdf2a (mac80211: add support for BSS color change)
Signed-off-by: Michael Lee <michael-cy.lee@mediatek.com>
Link: https://lore.kernel.org/r/20230504080441.22958-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We need to set the correct trace variable, otherwise we're
overwriting something else instead and the right one that
we print later is not initialized.
Fixes: b6011960f392 ("mac80211: handle channel frequency offset")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-2-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This feature depends on a platform bugfix. Until we have a
mechanism that can verify a platform has the required bugfix,
disable RFI.
Fixes: ef3ed33dfc8f ("wifi: iwlwifi: bump FW API to 77 for AX devices")
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Link: https://lore.kernel.org/linux-wireless/CAAJw_ZvZdFpw9W2Hisc9c2BAFbYAnQuaFFaFG6N7qPUP2fOL_w@mail.gmail.com/
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
'changed' can be OR'ed with BSS_CHANGED_EHT_PUNCTURING which is larger than
an u32.
So, turn 'changed' into an u64 and update ieee80211_set_after_csa_beacon()
accordingly.
In the commit in Fixes, only ieee80211_start_ap() was updated.
Fixes: 2cc25e4b2a04 ("wifi: mac80211: configure puncturing bitmap")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/e84a3f80fe536787f7a2c7180507efc36cd14f95.1682358088.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the function ieee80211_tx_dequeue() there is a particular locking
sequence:
begin:
spin_lock(&local->queue_stop_reason_lock);
q_stopped = local->queue_stop_reasons[q];
spin_unlock(&local->queue_stop_reason_lock);
However small the chance (increased by ftracetest), an asynchronous
interrupt can occur in between of spin_lock() and spin_unlock(),
and the interrupt routine will attempt to lock the same
&local->queue_stop_reason_lock again.
This will cause a costly reset of the CPU and the wifi device or an
altogether hang in the single CPU and single core scenario.
The only remaining spin_lock(&local->queue_stop_reason_lock) that
did not disable interrupts was patched, which should prevent any
deadlocks on the same CPU/core and the same wifi device.
This is the probable trace of the deadlock:
kernel: ================================
kernel: WARNING: inconsistent lock state
kernel: 6.3.0-rc6-mt-20230401-00001-gf86822a1170f #4 Tainted: G W
kernel: --------------------------------
kernel: inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kernel: kworker/5:0/25656 [HC0[0]:SC0[0]:HE1:SE1] takes:
kernel: ffff9d6190779478 (&local->queue_stop_reason_lock){+.?.}-{2:2}, at: return_to_handler+0x0/0x40
kernel: {IN-SOFTIRQ-W} state was registered at:
kernel: lock_acquire+0xc7/0x2d0
kernel: _raw_spin_lock+0x36/0x50
kernel: ieee80211_tx_dequeue+0xb4/0x1330 [mac80211]
kernel: iwl_mvm_mac_itxq_xmit+0xae/0x210 [iwlmvm]
kernel: iwl_mvm_mac_wake_tx_queue+0x2d/0xd0 [iwlmvm]
kernel: ieee80211_queue_skb+0x450/0x730 [mac80211]
kernel: __ieee80211_xmit_fast.constprop.66+0x834/0xa50 [mac80211]
kernel: __ieee80211_subif_start_xmit+0x217/0x530 [mac80211]
kernel: ieee80211_subif_start_xmit+0x60/0x580 [mac80211]
kernel: dev_hard_start_xmit+0xb5/0x260
kernel: __dev_queue_xmit+0xdbe/0x1200
kernel: neigh_resolve_output+0x166/0x260
kernel: ip_finish_output2+0x216/0xb80
kernel: __ip_finish_output+0x2a4/0x4d0
kernel: ip_finish_output+0x2d/0xd0
kernel: ip_output+0x82/0x2b0
kernel: ip_local_out+0xec/0x110
kernel: igmpv3_sendpack+0x5c/0x90
kernel: igmp_ifc_timer_expire+0x26e/0x4e0
kernel: call_timer_fn+0xa5/0x230
kernel: run_timer_softirq+0x27f/0x550
kernel: __do_softirq+0xb4/0x3a4
kernel: irq_exit_rcu+0x9b/0xc0
kernel: sysvec_apic_timer_interrupt+0x80/0xa0
kernel: asm_sysvec_apic_timer_interrupt+0x1f/0x30
kernel: _raw_spin_unlock_irqrestore+0x3f/0x70
kernel: free_to_partial_list+0x3d6/0x590
kernel: __slab_free+0x1b7/0x310
kernel: kmem_cache_free+0x52d/0x550
kernel: putname+0x5d/0x70
kernel: do_sys_openat2+0x1d7/0x310
kernel: do_sys_open+0x51/0x80
kernel: __x64_sys_openat+0x24/0x30
kernel: do_syscall_64+0x5c/0x90
kernel: entry_SYSCALL_64_after_hwframe+0x72/0xdc
kernel: irq event stamp: 5120729
kernel: hardirqs last enabled at (5120729): [<ffffffff9d149936>] trace_graph_return+0xd6/0x120
kernel: hardirqs last disabled at (5120728): [<ffffffff9d149950>] trace_graph_return+0xf0/0x120
kernel: softirqs last enabled at (5069900): [<ffffffff9cf65b60>] return_to_handler+0x0/0x40
kernel: softirqs last disabled at (5067555): [<ffffffff9cf65b60>] return_to_handler+0x0/0x40
kernel:
other info that might help us debug this:
kernel: Possible unsafe locking scenario:
kernel: CPU0
kernel: ----
kernel: lock(&local->queue_stop_reason_lock);
kernel: <Interrupt>
kernel: lock(&local->queue_stop_reason_lock);
kernel:
*** DEADLOCK ***
kernel: 8 locks held by kworker/5:0/25656:
kernel: #0: ffff9d618009d138 ((wq_completion)events_freezable){+.+.}-{0:0}, at: process_one_work+0x1ca/0x530
kernel: #1: ffffb1ef4637fe68 ((work_completion)(&local->restart_work)){+.+.}-{0:0}, at: process_one_work+0x1ce/0x530
kernel: #2: ffffffff9f166548 (rtnl_mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40
kernel: #3: ffff9d6190778728 (&rdev->wiphy.mtx){+.+.}-{3:3}, at: return_to_handler+0x0/0x40
kernel: #4: ffff9d619077b480 (&mvm->mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40
kernel: #5: ffff9d61907bacd8 (&trans_pcie->mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40
kernel: #6: ffffffff9ef9cda0 (rcu_read_lock){....}-{1:2}, at: iwl_mvm_queue_state_change+0x59/0x3a0 [iwlmvm]
kernel: #7: ffffffff9ef9cda0 (rcu_read_lock){....}-{1:2}, at: iwl_mvm_mac_itxq_xmit+0x42/0x210 [iwlmvm]
kernel:
stack backtrace:
kernel: CPU: 5 PID: 25656 Comm: kworker/5:0 Tainted: G W 6.3.0-rc6-mt-20230401-00001-gf86822a1170f #4
kernel: Hardware name: LENOVO 82H8/LNVNB161216, BIOS GGCN51WW 11/16/2022
kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211]
kernel: Call Trace:
kernel: <TASK>
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: dump_stack_lvl+0x5f/0xa0
kernel: dump_stack+0x14/0x20
kernel: print_usage_bug.part.46+0x208/0x2a0
kernel: mark_lock.part.47+0x605/0x630
kernel: ? sched_clock+0xd/0x20
kernel: ? trace_clock_local+0x14/0x30
kernel: ? __rb_reserve_next+0x5f/0x490
kernel: ? _raw_spin_lock+0x1b/0x50
kernel: __lock_acquire+0x464/0x1990
kernel: ? mark_held_locks+0x4e/0x80
kernel: lock_acquire+0xc7/0x2d0
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: ? ftrace_return_to_handler+0x8b/0x100
kernel: ? preempt_count_add+0x4/0x70
kernel: _raw_spin_lock+0x36/0x50
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: ieee80211_tx_dequeue+0xb4/0x1330 [mac80211]
kernel: ? prepare_ftrace_return+0xc5/0x190
kernel: ? ftrace_graph_func+0x16/0x20
kernel: ? 0xffffffffc02ab0b1
kernel: ? lock_acquire+0xc7/0x2d0
kernel: ? iwl_mvm_mac_itxq_xmit+0x42/0x210 [iwlmvm]
kernel: ? ieee80211_tx_dequeue+0x9/0x1330 [mac80211]
kernel: ? __rcu_read_lock+0x4/0x40
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_mvm_mac_itxq_xmit+0xae/0x210 [iwlmvm]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_mvm_queue_state_change+0x311/0x3a0 [iwlmvm]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_mvm_wake_sw_queue+0x17/0x20 [iwlmvm]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_txq_gen2_unmap+0x1c9/0x1f0 [iwlwifi]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_txq_gen2_free+0x55/0x130 [iwlwifi]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_txq_gen2_tx_free+0x63/0x80 [iwlwifi]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: _iwl_trans_pcie_gen2_stop_device+0x3f3/0x5b0 [iwlwifi]
kernel: ? _iwl_trans_pcie_gen2_stop_device+0x9/0x5b0 [iwlwifi]
kernel: ? mutex_lock_nested+0x4/0x30
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_trans_pcie_gen2_stop_device+0x5f/0x90 [iwlwifi]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_mvm_stop_device+0x78/0xd0 [iwlmvm]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: __iwl_mvm_mac_start+0x114/0x210 [iwlmvm]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: iwl_mvm_mac_start+0x76/0x150 [iwlmvm]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: drv_start+0x79/0x180 [mac80211]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: ieee80211_reconfig+0x1523/0x1ce0 [mac80211]
kernel: ? synchronize_net+0x4/0x50
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: ieee80211_restart_work+0x108/0x170 [mac80211]
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: process_one_work+0x250/0x530
kernel: ? ftrace_regs_caller_end+0x66/0x66
kernel: worker_thread+0x48/0x3a0
kernel: ? __pfx_worker_thread+0x10/0x10
kernel: kthread+0x10f/0x140
kernel: ? __pfx_kthread+0x10/0x10
kernel: ret_from_fork+0x29/0x50
kernel: </TASK>
Fixes: 4444bc2116ae ("wifi: mac80211: Proper mark iTXQs for resumption")
Link: https://lore.kernel.org/all/1f58a0d1-d2b9-d851-73c3-93fcc607501c@alu.unizg.hr/
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Cc: Gregory Greenman <gregory.greenman@intel.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/all/cdc80531-f25f-6f9d-b15f-25e16130b53a@alu.unizg.hr/
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: tag, or it goes automatically?
Link: https://lore.kernel.org/r/20230425164005.25272-1-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Ignore AP information for entries that include an invalid
BSSID in the TBTT information field, e.g., all zeros BSSIDs.
Fixes: c8cb5b854b40 ("nl80211/cfg80211: support 6 GHz scanning")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230424103224.5e65d04d1448.Ic10c8577ae4a85272c407106c9d0a2ecb5372743@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Give proper names:
RF6052_REG_UNKNOWN_56 -> RF6052_REG_PAD_TXG
RF6052_REG_UNKNOWN_DF -> RF6052_REG_GAIN_CCA
And fix typos:
REG_OFDM0_AGCR_SSI_TABLE -> REG_OFDM0_AGC_RSSI_TABLE
REG_BB_ACCEESS_CTRL -> REG_BB_ACCESS_CTRL
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/40157253-76bd-8b23-06e0-3365139b5395@gmail.com
|
|
This is a newer chip, similar to the RTL8710BU in that it uses the same
PHY status structs.
Features: 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps.
It can allegedly have Bluetooth, but that's not implemented here.
This chip can have many RFE (RF front end) types, of which types 1
and 5 are the only ones tested. Many of the other types need different
initialisation tables. They can be added if someone wants them.
The vendor driver v5.8.6.2_35538.20191028_COEX20190910-0d02 from
https://github.com/BrightX/rtl8192fu was used as reference, with
additional device IDs taken from
https://github.com/kelebek333/rtl8192fu-dkms.
The vendor driver also claims to support devices with ID 0bda:a725,
but that is found in some bluetooth-only devices, so it's not supported
here.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7dcf9fb9-1c97-ac28-5286-2236e287a18c@gmail.com
|
|
The message is attach and detach function are merly for debugging,
change them from pr_err to pr_debug.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230509100420.26094-1-matthias.bgg@kernel.org
|
|
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a
probability of failure, which shows "authentication with ... timed out".
Through debugging, it was found that the RCR register has been inexplicably
modified to an incorrect value, resulting in the nic not being able to
receive authenticated frames.
To fix this problem, add regrcr in rtl8xxxu_priv struct, and store
the RCR value every time the register is written, and use it the next
time the register need to be modified.
Signed-off-by: Yun Lu <luyun@kylinos.cn>
Link: https://lore.kernel.org/all/20230427020512.1221062-1-luyun_611@163.com
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512012055.2990472-1-luyun_611@163.com
|
|
The probe() id argument may be NULL in 2 scenarios:
1. brcmf_pcie_pm_leave_D3() calling brcmf_pcie_probe() to reprobe
the device.
2. If a user tries to manually bind the driver from sysfs then the sdio /
pcie / usb probe() function gets called with NULL as id argument.
1. Is being hit by users causing the following oops on resume and causing
wifi to stop working:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
Hardware name: Dell Inc. XPS 13 9350/0PWNCR, BIDS 1.13.0 02/10/2020
Workgueue: events_unbound async_run_entry_fn
RIP: 0010:brcmf_pcie_probe+Ox16b/0x7a0 [brcmfmac]
<snip>
Call Trace:
<TASK>
brcmf_pcie_pm_leave_D3+0xc5/8x1a0 [brcmfmac be3b4cefca451e190fa35be8f00db1bbec293887]
? pci_pm_resume+0x5b/0xf0
? pci_legacy_resume+0x80/0x80
dpm_run_callback+0x47/0x150
device_resume+0xa2/0x1f0
async_resume+0x1d/0x30
<snip>
Fix this by checking for id being NULL.
In the PCI and USB cases try a manual lookup of the id so that manually
binding the driver through sysfs and more importantly brcmf_pcie_probe()
on resume will work.
For the SDIO case there is no helper to do a manual sdio_device_id lookup,
so just directly error out on a NULL id there.
Fixes: da6d9c8ecd00 ("wifi: brcmfmac: add firmware vendor info in driver info")
Reported-by: Felix <nimrod4garoa@gmail.com>
Link: https://lore.kernel.org/regressions/4ef3f252ff530cbfa336f5a0d80710020fc5cb1e.camel@gmail.com/
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230510141856.46532-1-hdegoede@redhat.com
|
|
qsel_to_ep[] can be assigned negative value, so change type from 'u8' to
'int'. Otherwise, Smatch static checker warns:
drivers/net/wireless/realtek/rtw88/usb.c:219 rtw_usb_parse() warn:
assigning (-22) to unsigned variable 'rtwusb->qsel_to_ep[8]'
Cc: stable@vger.kernel.org
Fixes: a6f187f92bcc ("wifi: rtw88: usb: fix priority queue to endpoint mapping")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/linux-wireless/c3f70197-829d-48ed-ae15-66a9de80fa90@kili.mountain/
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508085539.46795-1-pkshih@realtek.com
|
|
As low_thresh has no work in fragment reassembles,del it.
And Mark it deprecated in sysctl Document.
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle valo says:
====================
wireless-next patches for v6.5
The first pull request for v6.5 and only driver changes this time.
rtl8xxxu has been making lots of progress lately and now has AP mode
support.
Major changes:
rtl8xxxu
* AP mode support, initially only for rtl8188f
rtw89
* provide RSSI, EVN and SNR statistics via debugfs
* support U-NII-4 channels on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When writing error messages to extack for pseudo collisions, we can't
use encap->type as encap has already been freed. Fortunately the
same value is stored in local variable em_type, so use that instead.
Fixes: 3c9561c0a5b9 ("sfc: support TC decap rules matching on enc_ip_tos")
Reported-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both phylink_create() and phylink_fwnode_phy_connect() do not modify
the fwnode argument that they are passed, so lets constify these.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch standardizes the inconsistent return values for unsuccessful
XDP transmits by using standardized error codes (-EBUSY or -ENOMEM).
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On mpfs, with SRAM configured for 4 queues, setting max_tx_len
to GEM_TX_MAX_LEN=0x3f0 results multiple AMBA errors.
Setting max_tx_len to (4KiB - 56) removes those errors.
The details are described in erratum 1686 by Cadence
The max jumbo frame size is also reduced for mpfs to (4KiB - 56).
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since introduced in commit c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP
socket kind"), ping socket does not use SLAB_TYPESAFE_BY_RCU nor check
nulls marker in loops.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yunsheng Lin says:
====================
net: introduce skb_frag_fill_page_desc()
Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.
It does not make much sense to calling __skb_frag_set_page()
without calling skb_frag_off_set(), as the offset may depend
on whether the page is head page or tail page, so add
skb_frag_fill_page_desc() to fill the page desc for a skb
frag.
In the future, we can make sure the page in the frag is
head page of compound page or a base page, if not, we
may warn about that and convert the tail page to head
page and update the offset accordingly, if we see a warning
about that, we also fix the caller to fill the head page
in the frag. when the fixing is done, we may remove the
warning and converting.
In this way, we can remove the compound_head() or use
page_ref_*() like the below case:
https://elixir.bootlin.com/linux/latest/source/net/core/page_pool.c#L881
https://elixir.bootlin.com/linux/latest/source/include/linux/skbuff.h#L3383
It may also convert net stack to use the folio easier.
V1: repost with all the ack/review tags included.
RFC: remove a local variable as pointed out by Simon.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The remaining users calling __skb_frag_set_page() with
page being NULL seems to be doing defensive programming,
as shinfo->nr_frags is already decremented, so remove
them.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.
Introduce skb_frag_fill_page_desc() to do that.
net/bpf/test_run.c does not call skb_frag_off_set() to
set the offset, "copy_from_user(page_address(page), ...)"
and 'shinfo' being part of the 'data' kzalloced in
bpf_test_init() suggest that it is assuming offset to be
initialized as zero, so call skb_frag_fill_page_desc()
with offset being zero for this case.
Also, skb_frag_set_page() is not used anymore, so remove
it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add test to make sure that the localbypass option is on by default.
Add test to change vxlan localbypass to nolocalbypass and check
that packets are delivered to userspace.
Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a packet needs to be encapsulated towards a local destination IP, the
packet will undergo a "local bypass" and be injected into the Rx path as
if it was received by the target VXLAN device without undergoing
encapsulation. If such a device does not exist, the packet will be
dropped.
There are scenarios where we do not want to perform such a bypass, but
instead want the packet to be encapsulated and locally received by a
user space program for post-processing.
To that end, add a new VXLAN device attribute that controls whether a
"local bypass" is performed or not. Default to performing a bypass to
maintain existing behavior.
Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
Support for Wake-on-LAN for Broadcom PHYs
This patch series adds support for Wake-on-LAN to the Broadcom PHY
driver. Specifically the BCM54210E/B50212E are capable of supporting
Wake-on-LAN using an external pin typically wired up to a system's GPIO.
These PHY operate a programmable Ethernet MAC destination address
comparator which will fire up an interrupt whenever a match is received.
Because of that, it was necessary to introduce patch #1 which allows the
PHY driver's ->suspend() routine to be called unconditionally. This is
necessary in our case because we need a hook point into the device
suspend/resume flow to enable the wake-up interrupt as late as possible.
Patch #2 adds support for the Broadcom PHY library and driver for
Wake-on-LAN proper with the WAKE_UCAST, WAKE_MCAST, WAKE_BCAST,
WAKE_MAGIC and WAKE_MAGICSECURE. Note that WAKE_FILTER is supportable,
however this will require further discussions and be submitted as a RFC
series later on.
Patch #3 updates the GENET driver to defer to the PHY for Wake-on-LAN if
the PHY supports it, thus allowing the MAC to be powered down to
conserve power.
Changes in v3:
- collected Reviewed-by tags
- explicitly use return 0 in bcm54xx_phy_probe() (Paolo)
Changes in v2:
- introduce PHY_ALWAYS_CALL_SUSPEND and only have the Broadcom PHY
driver set this flag to minimize changes to the suspend flow to only
drivers that need it
- corrected possibly uninitialized variable in bcm54xx_set_wakeup_irq
(Simon)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If available, interrogate the PHY to find out whether we can use it for
Wake-on-LAN. This can be a more power efficient way of implementing
that feature, especially when the MAC is powered off in low power
states.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for WAKE_UCAST, WAKE_MCAST, WAKE_BCAST, WAKE_MAGIC and
WAKE_MAGICSECURE. This is only supported with the BCM54210E and
compatible Ethernet PHYs. Using the in-band interrupt or an out of band
GPIO interrupts are supported.
Broadcom PHYs will generate a Wake-on-LAN level low interrupt on LED4 as
soon as one of the supported patterns is being matched. That includes
generating such an interrupt even if the PHY is operated during normal
modes. If WAKE_UCAST is selected, this could lead to the LED4 interrupt
firing up for every packet being received which is absolutely
undesirable from a performance point of view.
Because the Wake-on-LAN configuration can be set long before the system
is actually put to sleep, we cannot have an interrupt service routine to
clear on read the interrupt status register and ensure that new packet
matches will be detected.
It is desirable to enable the Wake-on-LAN interrupt as late as possible
during the system suspend process such that we limit the number of
interrupts to be handled by the system, but also conversely feed into
the Linux's system suspend way of dealing with interrupts in and around
the points of no return.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few PHY drivers are currently attempting to not suspend the PHY when
Wake-on-LAN is enabled, however that code is not currently executing at
all due to an early check in phy_suspend().
This prevents PHY drivers from making an appropriate decisions and put
the hardware into a low power state if desired.
In order to allow the PHY drivers to opt into getting their ->suspend
routine to be called, add a PHY_ALWAYS_CALL_SUSPEND bit which can be
set. A boolean that tracks whether the PHY or the attached MAC has
Wake-on-LAN enabled is also provided for convenience.
If phydev::wol_enabled then the PHY shall not prevent its own
Wake-on-LAN detection logic from working and shall not prevent the
Ethernet MAC from receiving packets for matching.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Edward Cree says:
====================
sfc: more flexible encap matches on TC decap rules
This series extends the TC offload support on EF100 to support optionally
matching on the IP ToS and UDP source port of the outer header in rules
performing tunnel decapsulation. Both of these fields allow masked
matches if the underlying hardware supports it (current EF100 hardware
supports masking on ToS, but only exact-match on source port).
Given that the source port is typically populated from a hash of inner
header entropy, it's not clear whether filtering on it is useful, but
since we can support it we may as well expose the capability.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow efx_tc_encap_match entries to include a udp_sport and a
udp_sport_mask. As with enc_ip_tos, use pseudos to enforce that all
encap matches within a given <src_ip,dst_ip,udp_dport> tuple have
the same udp_sport_mask.
Note that since we use a single layer of pseudos for both fields, two
matches that differ in (say) udp_sport value aren't permitted to have
different ip_tos_mask, even though this would technically be safe.
Current userland TC does not support setting enc_src_port; this patch
was tested with an iproute2 patched to support it.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
