| Age | Commit message (Collapse) | Author |
|---|
|
The least significat byte of the GPIO value read register
on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct
against datasheet and tested on the STMPE2401 hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
bnx2fc_queuecommand(): when allocating a new io_req, the tgt_lock
spinlock must be locked before calling bnx2fc_cmd_alloc().
The spinlock should also be kept locked until bnx2fc_post_io_req() has
been completed.
If not, a kernel thread may call bnx2fc_process_cq_compl() that extracts
the newly allocated io_req from hba->cmd_mgr->cmds and destroys it while
it is still being used by bnx2fc_post_io_req().
BUG: unable to handle kernel NULL pointer dereference at 000000000000004c
IP: [<ffffffffa03130da>] bnx2fc_init_task+0x6a/0x230 [bnx2fc]
PGD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:02.0/0000:04:00.3/net/eth3/type
CPU 33
Modules linked in: autofs4 target_core_iblock target_core_file target_core_pscsi target_core_mod configfs bnx2fc cnic uio fcoe libfcoe libfc scsi_transport_fc 8021q garp scsi_tgt stp llc cpufreq_ondemand freq_table pcc_cpufreq ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 power_meter microcode iTCO_wdt iTCO_vendor_support hpilo hpwdt sg bnx2x libcrc32c mdio serio_raw lpc_ich mfd_core shpchp ext4 jbd2 mbcache sd_mod crc_t10dif hpsa video output dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan]
Pid: 7355, comm: bnx2fc_thread/3 Not tainted 2.6.32-431.el6.x86_64 #1 HP ProLiant BL460c Gen8
RIP: 0010:[<ffffffffa03130da>] [<ffffffffa03130da>] bnx2fc_init_task+0x6a/0x230 [bnx2fc]
RSP: 0018:ffff8820b0da3b68 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff882003801080 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff882003801100
RBP: ffff8820b0da3bc8 R08: ffffffff8160d4e8 R09: 0000000000000040
R10: 0000000000000000 R11: 0000000000000000 R12: ffff88400e600e00
R13: ffff8840108fbe40 R14: ffff88200ffe5400 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8820b0da0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 000000000000004c CR3: 0000002010b67000 CR4: 00000000001407e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process bnx2fc_thread/3 (pid: 7355, threadinfo ffff88401f940000, task ffff884012f5f540)
Stack:
ffff8820b0da3bc8 ffffffff81527303 ffff884000000020 ffff8820b0da3bd8
<d> ffff8820b0da3b98 000000028138931a ffff88400f506078 ffff88400e600e00
<d> ffff88200ffe5400 ffff88200ffe5590 0000000000000021 0000000000000002
Call Trace:
<IRQ>
[<ffffffff81527303>] ? printk+0x41/0x46
[<ffffffffa03169bc>] bnx2fc_post_io_req+0x11c/0x440 [bnx2fc]
[<ffffffff812825b9>] ? cpumask_next_and+0x29/0x50
[<ffffffff8137ffd0>] ? scsi_done+0x0/0x60
[<ffffffffa0316df7>] bnx2fc_queuecommand+0x117/0x140 [bnx2fc]
[<ffffffff81380245>] scsi_dispatch_cmd+0xe5/0x310
[<ffffffff81388b9e>] scsi_request_fn+0x5ee/0x7a0
[<ffffffff812658f1>] __blk_run_queue+0x31/0x40
[<ffffffff81265a40>] blk_run_queue+0x30/0x50
[<ffffffff81387da6>] scsi_run_queue+0xc6/0x270
[<ffffffff81260f92>] ? elv_requeue_request+0x52/0xa0
[<ffffffff813897a0>] scsi_requeue_command+0x90/0xb0
[<ffffffff81389b84>] scsi_io_completion+0x154/0x6c0
[<ffffffff8137ff62>] scsi_finish_command+0xc2/0x130
[<ffffffff8138a255>] scsi_softirq_done+0x145/0x170
[<ffffffff8126e865>] blk_done_softirq+0x85/0xa0
[<ffffffff8107a8e1>] __do_softirq+0xc1/0x1e0
[<ffffffff8100c30c>] ? call_softirq+0x1c/0x30
[<ffffffff8100c30c>] call_softirq+0x1c/0x30
<EOI>
[<ffffffff8100fa75>] ? do_softirq+0x65/0xa0
[<ffffffff8107a40a>] local_bh_enable_ip+0x9a/0xb0
[<ffffffff8152a4eb>] _spin_unlock_bh+0x1b/0x20
[<ffffffffa0313937>] bnx2fc_process_cq_compl+0x257/0x2b0 [bnx2fc]
[<ffffffffa03114ea>] bnx2fc_percpu_io_thread+0xea/0x160 [bnx2fc]
[<ffffffffa0311400>] ? bnx2fc_percpu_io_thread+0x0/0x160 [bnx2fc]
[<ffffffff8109aef6>] kthread+0x96/0xa0
[<ffffffff8100c20a>] child_rip+0xa/0x20
[<ffffffff8109ae60>] ? kthread+0x0/0xa0
[<ffffffff8100c200>] ? child_rip+0x0/0x20
Code: 89 df 45 8b 7e 30 0f 85 75 01 00 00 89 d1 31 c0 c1 e9 03 83 e2 04 89 c9 f3 48 ab 74 06 c7 07 00 00 00 00 49 89 9c 24 88 01 00 00 <83> 7e 4c 01 b8 01 00 00 00 0f 84 e7 00 00 00 89 c2 0a 53 38 41
RIP [<ffffffffa03130da>] bnx2fc_init_task+0x6a/0x230 [bnx2fc]
RSP <ffff8820b0da3b68>
CR2: 000000000000004c
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Function pci_enable_msix_range() may return negative values for error
conditions. So it's a bug by checking (pci_enable_msix_range() != 0)
for success and causes failure to megaraid driver when MSI is disabled.
[ 16.487267] megaraid_sas 0000:02:00.0: Controller type: iMR
[ 16.487275] genirq: Flags mismatch irq 0. 00000000 (megasas) vs. 00015a00 (tii
mer)
[ 16.487347] megasas: Failed to register IRQ for vector 0.
Fixes: 8ae80ed1734b "megaraid: Use pci_enable_msix_range() instead of pci_enable_msix()"
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # 3.17
|
|
Connection retries were not being cleaned up correctly if they failed as a
result of link down. Applies on top of drivers-for-3.18.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch fixes an issue with multipath ipr SAS devices which require a
start unit command to be issued following an adapter reset. Without this
patch, paths get marked failed following an adapter reset and since the
error handler never gets invoked to issue the start unit, the paths are
never recovered. Returning FAILED for this case ensures the error
handler wakes up to issue the start unit.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Multipath devices using the TUR path checker need to see the sense
code for a failed TUR command in their device handler. Since commit
14216561e164671ce147458653b1fea06a we always return success for mid
layer issued TUR commands before calling the device handler, which
stopped the TUR path checker from working.
Move the call to the device handler check sense method before the early
return for TUR commands to give the device handler a chance to intercept
them.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH. Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state. Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Meelis Roos <meelis.roos@ut.ee>
Tested-by: Meelis Roos <meelis.roos@ut.ee>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Save the patch while we're running on the BSP instead of later, before
the initrd has been jettisoned. More importantly, on 32-bit we need to
access the physical address instead of the virtual.
This way we actually do find it on the APs instead of having to go
through the initrd each time.
Tested-by: Richard Hendershot <rshendershot@mchsi.com>
Fixes: 5335ba5cf475 ("x86, microcode, AMD: Fix early ucode loading")
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Commit 2ed53c0d6cc9 ("x86/smpboot: Speed up suspend/resume by
avoiding 100ms sleep for CPU offline during S3") introduced
completions to CPU offlining process. These completions are not
initialized on Xen kernels causing a panic in
play_dead_common().
Move handling of die_complete into common routines to make them
available to Xen guests.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: tianyu.lan@intel.com
Cc: konrad.wilk@oracle.com
Cc: xen-devel@lists.xenproject.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1414770572-7950-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Linux 3.18-rc4
|
|
On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte
in 6 bytes ALPS packet. In this case psmouse driver enter out of sync
state. It looks like that all other bytes in packets are valid and also
device working properly. So there is no need to do full device reset, just
need to wait for byte which match condition for first byte (start of
packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is
small.
This patch increase number of invalid bytes to size of 2 ALPS packets which
psmouse driver can drop before do full reset.
Resetting ALPS devices take some time and when doing reset on some Dell
laptops touchpad, trackstick and also keyboard do not respond. So it is
better to do it only if really necessary.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch fixes possible infinite loop issue by postponing
registration to non kms drivers after component_master_add_with_match
call, which can be incurred in all cases that non kms driver is probed
and then component bind is failed
This patch should be applied on top of below patches,
http://comments.gmane.org/gmane.comp.video.dri.devel/117740
http://www.spinics.net/lists/linux-samsung-soc/msg38624.html
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch fixes a null pointer dereference issue incurred by
calling g2d_remove when exynos_drm_platform_probe is failed.
cmdlist_pool of g2d is allocated when g2d sub driver is probed.
So if exynos_drm_platform_probe is failed, the g2d sub driver is
not probed and the cmdlist_pool is still NULL.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch resovles the infinite loop issue incurred
when Exyno drm driver is enabled but all kms drivers
are disabled on Exynos board by returning -EPROBE_DEFER
only in case that there is kms device registered.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch resolves temporarily infinite loop issue incurred
when Exynos drm driver is enabled and multi-platform kernel
is used by registering Exynos drm device object only in case
of Exynos SoC. So this patch will be replaced with more generic
way later.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Black screen, screen corruption, hardware state corruption fixes.
* tag 'drm-intel-fixes-2014-11-07' of git://anongit.freedesktop.org/drm-intel:
drm/i915: safeguard against too high minimum brightness
drm/i915: vlv: fix gunit HW state corruption during S4 suspend
drm/i915: Disable caches for Global GTT.
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree bugfix from Grant Likely:
"One buffer overflow bug that shouldn't be left around"
* 'devicetree/merge' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of: Fix overflow bug in string property parsing functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
|
|
imx_get_temp might be called before the sensor clock is prepared
thus resulting in a timeout of the first attempt to read temp:
thermal thermal_zone0: failed to read out thermal zone 0
Happened to me on a Utilite Standard with IMX6 Dual SoC.
Reason is that in imx_thermal_probe thermal_zone_device_register
is called before the sensor clock is prepared.
thermal_zone_device_register however calls
thermal_zone_device_update which eventually calls imx_get_temp.
Fix this by preparing the clock before calling
thermal_zone_device_register.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.
It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.
Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.
This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.
So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
If no freeze_ops is set, trying to enter suspend-to-IDLE will cause a
nice oops in platform_suspend_prepare_late(). Add respective checks to
platform_suspend_prepare_late() and platform_resume_early() functions.
Fixes: a8d46b9e4e48 (ACPI / sleep: Rework the handling of ACPI GPE wakeup ...)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch adds DeviceIDs for Sunrise Point-LP
Signed-off-by: Devin Ryles <devin.ryles@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two fixlets for the armada SoC interrupt controller"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: armada-370-xp: Fix MPIC interrupt handling
irqchip: armada-370-xp: Fix MSI interrupt handling
|
|
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
|
|
The Fujitsu H730 does not work with crc_enabled = 0, even though the
crc_enabled bit in the firmware version indicated it would. When switching
this value to crc_enabled to 1, the touchpad works. This patch uses DMI to
detect H730.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Fujitsu H730 has hardware v4 with a trackpoint. This enables the
elantech_report_trackpoint for v4.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This button is treated as a wakeup source, so we need to initialise it
correctly.
Without the device_init_wakeup() call, dev->power.wakeup will
be NULL, and pm_wakeup_event() will do nothing.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
|
|
Convert the prototypes to return an int in order to support error
handling in these callbacks.
Also, as suggested by Dmitry Torokhov, pass the domain pointer for use
inside the callbacks, and so that they match the existing
power_on/power_off callbacks which currently take the domain pointer.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ khilman: added domain as parameter to callbacks, as suggested by Dmitry ]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When resuming from s2ram on an SMP system without cpufreq operating
points (e.g. there's no "operating-points" property for the CPU node in
DT, or the platform doesn't use DT yet), the kernel crashes when
bringing CPU 1 online:
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
Unable to handle kernel NULL pointer dereference at virtual address 0000003c
pgd = ee5e6b00
[0000003c] *pgd=6e579003, *pmd=6e588003, *pte=00000000
Internal error: Oops: a07 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1246 Comm: s2ram Tainted: G W 3.18.0-rc3-koelsch-01614-g0377af242bb175c8-dirty #589
task: eeec5240 ti: ee704000 task.ti: ee704000
PC is at __cpufreq_add_dev.isra.24+0x24c/0x77c
LR is at __cpufreq_add_dev.isra.24+0x244/0x77c
pc : [<c0298efc>] lr : [<c0298ef4>] psr: 60000153
sp : ee705d48 ip : ee705d48 fp : ee705d84
r10: c04e0450 r9 : 00000000 r8 : 00000001
r7 : c05426a8 r6 : 00000001 r5 : 00000001 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 20000153 r0 : c0542734
Verify that policy is not NULL before dereferencing it to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 8414809c6a1e (cpufreq: Preserve policy structure across suspend/resume)
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
|
|
Atomicity between xchg and cmpxchg cannot be guaranteed when xchg is
implemented with a swap and cmpxchg is implemented with locks.
Without this, e.g. mcs_spin_lock and mcs_spin_unlock are broken.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 3cc81d85ee01 ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.
It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.
It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"More changes than I'd like here, most of them for a single bug
repeated in a bunch of drivers with data not being initialized
correctly, plus a fix to lower the severity of a warning introduced in
the last merge window which can legitimately go off so we don't want
to alarm users excessively"
* tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mpa01: zero-initialize regulator match table array
regulator: max8660: zero-initialize regulator match table array
regulator: max77802: zero-initialize regulator match table
regulator: max77686: zero-initialize regulator match table
regulator: max1586: zero-initialize regulator match table array
regulator: max77693: Fix use of uninitialized regulator config
regulator: of: Lower the severity of the error with no container
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi bugfixes from Mark Brown:
"A couple of small driver fixes for v3.18, both quite problematic if
you hit a use case that's affected"
* tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
spi: fsl-dspi: Fix CTAR selection
|
|
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
Cc: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In exynos5260_tmu_registers tmu_ctrl entry is erroneously
assigned twice. The second assignment (to EXYNOS_TMU_REG_CONTROL1
define which represents 0x24 value) overrides the first one
(to EXYNOS_TMU_REG_CONTROL define which represents 0x20 value)
which results in the wrong (according to the Exynos5260 SoC
documentation that I have) offset being used for TMU_CONTROL
register. Fix it by removing the wrong assignment and then
remove no longer used EXYNOS_TMU_REG_CONTROL1 define.
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
thermal driver should be regisetered after cpufreq driver has
been registered and probed. Doing so is to make sure that thermal
driver can get the max cpu cooling states correctly when calling
get_property.
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Add a i8042 filter to hp_accel to remove accelerometer's data with acpi
id HPQ6000 from keyboard bus stream. The codes sent by accelerometer are
e0 25, e0 26, e0 27 and e0 28. The relevant information is already
passed through /dev/freefall so no need to send these undocumented weird
signals through the keyboard bus. Also, unclogs `dmesg` because atkbd
complained about weird scan codes, saves processing power and disk
space.
Signed-off-by: Giedrius Statkevičius <giedriuswork@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
