| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more one-liners that fix some user visible problems:
- use correct range when clearing qgroup reservations after COW
- properly reset freed delayed ref list head
- fix ro/rw subvolume mounts to be backward compatible with old and
new mount API"
* tag 'for-6.12-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix the length of reserved qgroup to free
btrfs: reinitialize delayed ref list after deleting it from the list
btrfs: fix per-subvolume RO/RW flags with new mount API
|
|
Pull bcachefs fixes from Kent Overstreet:
"Some trivial syzbot fixes, two more serious btree fixes found by
looping single_devices.ktest small_nodes:
- Topology error on split after merge, where we accidentaly picked
the node being deleted for the pivot, resulting in an assertion pop
- New nodes being preallocated were left on the freedlist, unlocked,
resulting in them sometimes being accidentally freed: this dated
from pre-cycle detector, when we could leave them locked. This
should have resulted in more explosions and fireworks, but turned
out to be surprisingly hard to hit because the preallocated nodes
were being used right away.
The fix for this is bigger than we'd like - reworking btree list
handling was a bit invasive - but we've now got more assertions and
it's well tested.
- Also another mishandled transaction restart fix (in
btree_node_prefetch) - we're almost done with those"
* tag 'bcachefs-2024-11-07' of git://evilpiepirate.org/bcachefs:
bcachefs: Fix UAF in __promote_alloc() error path
bcachefs: Change OPT_STR max to be 1 less than the size of choices array
bcachefs: btree_cache.freeable list fixes
bcachefs: check the invalid parameter for perf test
bcachefs: add check NULL return of bio_kmalloc in journal_read_bucket
bcachefs: Ensure BCH_FS_may_go_rw is set before exiting recovery
bcachefs: Fix topology errors on split after merge
bcachefs: Ancient versions with bad bkey_formats are no longer supported
bcachefs: Fix error handling in bch2_btree_node_prefetch()
bcachefs: Fix null ptr deref in bucket_gen_get()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here is a (hopefully) final round of arm64 fixes for 6.12 that address
some user-visible floating point register corruption. Both of the
Marks have been working on this for a couple of weeks and we've ended
up in a position where SVE is solid but SME still has enough pending
issues that the most pragmatic solution for the release and stable
backports is to disable the feature. Yes, it's a shame, but the
hardware is rare as hen's teeth at the moment and we're better off
getting back to a known good state before fixing it all properly.
We're also improving the selftests for 6.13 to help avoid merging
broken code in the future.
Anyway, the good news is that we're removing a lot more code than
we're adding.
Summary:
- Fix handling of SVE traps from userspace on preemptible kernels
when converting the saved floating point state into SVE state.
- Remove broken support for the SMCCCv1.3 "SVE discard hint"
optimisation.
- Disable SME support, as the current support code suffers from
numerous issues around signal delivery, ptrace access and
context-switch which can lead to user-visible corruption of the
register state"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Kconfig: Make SME depend on BROKEN for now
arm64: smccc: Remove broken support for SMCCCv1.3 SVE discard hint
arm64/sve: Discard stale CPU state when handling SVE traps
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Madhavan Srinivasan:
- Fix spurious interrupts in Book3S HV Nested KVM
Thanks to Gautam Menghani.
* tag 'powerpc-6.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Mask off LPCR_MER for a vCPU before running it to avoid spurious interrupts
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.12
A moderately large pile of small changes here, split fairly evenly
between fixes and ID additions/quirks and all of it driver specific.
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.12-rc7
Here's a fix for a long-standing use-after-free in an io_edgeport debug
printk and some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add support for Sierra Wireless EM86xx
USB: serial: io_edgeport: fix use after free in debug printk
USB: serial: option: add Quectel RG650V
USB: serial: option: add Fibocom FG132 0x0112 composition
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.12-2024-11-07:
amdgpu:
- Brightness fix
- DC vbios parsing fix
- ACPI fix
- SMU 14.x fix
- Power workload profile fix
- GC partitioning fix
- Debugfs fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241107182722.14147-1-alexander.deucher@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"An update for the maintainers of the AMD driver following some job
changes there"
* tag 'spi-fix-v6.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
MAINTAINERS: update AMD SPI maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small fixes for drivers, nothing particularly remarkable"
* tag 'regulator-fix-v6.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: rk808: Add apply_bit for BUCK3 on RK809
regulator: rtq2208: Fix uninitialized use of regulator_config
|
|
Map my previously used email address to my @linux.dev address.
Link: https://lkml.kernel.org/r/20241103234411.2522-2-thorsten.blum@linux.dev
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Cc: Alex Elder <elder@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Geliang Tang <geliang@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: Mathieu Othacehe <m.othacehe@gmail.com>
Cc: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Cc: Matt Ranostay <matt@ranostay.sg>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Cc: Neeraj Upadhyay <neeraj.upadhyay@kernel.org>
Cc: Quentin Monnet <qmo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Syzkaller is able to provoke null-ptr-dereference in ocfs2_xa_remove():
[ 57.319872] (a.out,1161,7):ocfs2_xa_remove:2028 ERROR: status = -12
[ 57.320420] (a.out,1161,7):ocfs2_xa_cleanup_value_truncate:1999 ERROR: Partial truncate while removing xattr overlay.upper. Leaking 1 clusters and removing the entry
[ 57.321727] BUG: kernel NULL pointer dereference, address: 0000000000000004
[...]
[ 57.325727] RIP: 0010:ocfs2_xa_block_wipe_namevalue+0x2a/0xc0
[...]
[ 57.331328] Call Trace:
[ 57.331477] <TASK>
[...]
[ 57.333511] ? do_user_addr_fault+0x3e5/0x740
[ 57.333778] ? exc_page_fault+0x70/0x170
[ 57.334016] ? asm_exc_page_fault+0x2b/0x30
[ 57.334263] ? __pfx_ocfs2_xa_block_wipe_namevalue+0x10/0x10
[ 57.334596] ? ocfs2_xa_block_wipe_namevalue+0x2a/0xc0
[ 57.334913] ocfs2_xa_remove_entry+0x23/0xc0
[ 57.335164] ocfs2_xa_set+0x704/0xcf0
[ 57.335381] ? _raw_spin_unlock+0x1a/0x40
[ 57.335620] ? ocfs2_inode_cache_unlock+0x16/0x20
[ 57.335915] ? trace_preempt_on+0x1e/0x70
[ 57.336153] ? start_this_handle+0x16c/0x500
[ 57.336410] ? preempt_count_sub+0x50/0x80
[ 57.336656] ? _raw_read_unlock+0x20/0x40
[ 57.336906] ? start_this_handle+0x16c/0x500
[ 57.337162] ocfs2_xattr_block_set+0xa6/0x1e0
[ 57.337424] __ocfs2_xattr_set_handle+0x1fd/0x5d0
[ 57.337706] ? ocfs2_start_trans+0x13d/0x290
[ 57.337971] ocfs2_xattr_set+0xb13/0xfb0
[ 57.338207] ? dput+0x46/0x1c0
[ 57.338393] ocfs2_xattr_trusted_set+0x28/0x30
[ 57.338665] ? ocfs2_xattr_trusted_set+0x28/0x30
[ 57.338948] __vfs_removexattr+0x92/0xc0
[ 57.339182] __vfs_removexattr_locked+0xd5/0x190
[ 57.339456] ? preempt_count_sub+0x50/0x80
[ 57.339705] vfs_removexattr+0x5f/0x100
[...]
Reproducer uses faultinject facility to fail ocfs2_xa_remove() ->
ocfs2_xa_value_truncate() with -ENOMEM.
In this case the comment mentions that we can return 0 if
ocfs2_xa_cleanup_value_truncate() is going to wipe the entry
anyway. But the following 'rc' check is wrong and execution flow do
'ocfs2_xa_remove_entry(loc);' twice:
* 1st: in ocfs2_xa_cleanup_value_truncate();
* 2nd: returning back to ocfs2_xa_remove() instead of going to 'out'.
Fix this by skipping the 2nd removal of the same entry and making
syzkaller repro happy.
Link: https://lkml.kernel.org/r/20241103193845.2940988-1-andrew.kanner@gmail.com
Fixes: 399ff3a748cf ("ocfs2: Handle errors while setting external xattr values.")
Signed-off-by: Andrew Kanner <andrew.kanner@gmail.com>
Reported-by: syzbot+386ce9e60fa1b18aac5b@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/671e13ab.050a0220.2b8c0f.01d0.GAE@google.com/T/
Tested-by: syzbot+386ce9e60fa1b18aac5b@syzkaller.appspotmail.com
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Prior to commit d64696905554 ("Reimplement RLIMIT_SIGPENDING on top of
ucounts") UCOUNT_RLIMIT_SIGPENDING rlimit was not enforced for a class of
signals. However now it's enforced unconditionally, even if
override_rlimit is set. This behavior change caused production issues.
For example, if the limit is reached and a process receives a SIGSEGV
signal, sigqueue_alloc fails to allocate the necessary resources for the
signal delivery, preventing the signal from being delivered with siginfo.
This prevents the process from correctly identifying the fault address and
handling the error. From the user-space perspective, applications are
unaware that the limit has been reached and that the siginfo is
effectively 'corrupted'. This can lead to unpredictable behavior and
crashes, as we observed with java applications.
Fix this by passing override_rlimit into inc_rlimit_get_ucounts() and skip
the comparison to max there if override_rlimit is set. This effectively
restores the old behavior.
Link: https://lkml.kernel.org/r/20241104195419.3962584-1-roman.gushchin@linux.dev
Fixes: d64696905554 ("Reimplement RLIMIT_SIGPENDING on top of ucounts")
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Co-developed-by: Andrei Vagin <avagin@google.com>
Signed-off-by: Andrei Vagin <avagin@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Alexey Gladkov <legion@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
When build with !CONFIG_MMU, the variable 'vmcore_mmap_ops'
is defined but not used:
>> fs/proc/vmcore.c:458:42: warning: unused variable 'vmcore_mmap_ops'
458 | static const struct vm_operations_struct vmcore_mmap_ops = {
Fix this by only defining it when CONFIG_MMU is enabled.
Link: https://lkml.kernel.org/r/20241101034803.9298-1-xiqi2@huawei.com
Fixes: 9cb218131de1 ("vmcore: introduce remap_oldmem_pfn_range()")
Signed-off-by: Qi Xi <xiqi2@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/lkml/202410301936.GcE8yUos-lkp@intel.com/
Cc: Baoquan He <bhe@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The inc_rlimit_get_ucounts() increments the specified rlimit counter and
then checks its limit. If the value exceeds the limit, the function
returns an error without decrementing the counter.
Link: https://lkml.kernel.org/r/20241101191940.3211128-1-roman.gushchin@linux.dev
Fixes: 15bc01effefe ("ucounts: Fix signal ucount refcounting")
Signed-off-by: Andrei Vagin <avagin@google.com>
Co-developed-by: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Tested-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Alexey Gladkov <legion@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: Andrei Vagin <avagin@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexey Gladkov <legion@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The test should be skipped if initial conditions aren't fulfilled in the
start instead of failing and outputting non-compliant TAP logs. This kind
of failure pollutes the results. The initial conditions are:
- The test should only execute if /tmp file can be allocated.
- The test should only execute if huge pages are free.
Before:
TAP version 13
1..4
Bail out! Error opening file
: Read-only file system (30)
# Planned tests != run tests (4 != 0)
# Totals: pass:0 fail:0 xfail:0 xpass:0 skip:0 error:0
After:
TAP version 13
1..0 # SKIP Unable to allocate file: Read-only file system
Link: https://lkml.kernel.org/r/20241101141557.3159432-1-usama.anjum@collabora.com
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Fixes: 3a103b5315b7 ("selftest: mm: Test if hugepage does not get leaked during __bio_release_pages()")
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Donet Tom <donettom@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
If we add ``thp_anon=32,64K:always`` to the kernel command line, we
will see the following error:
[ 0.000000] huge_memory: thp_anon=32,64K:always: error parsing string, ignoring setting
This happens because the correct format isn't ``thp_anon=<size>,<size>[KMG]:<state>```,
as [KMG] must follow each number to especify its unit. So, the correct
format is ``thp_anon=<size>[KMG],<size>[KMG]:<state>```.
Therefore, adjust the documentation to reflect the correct format of the
parameter ``thp_anon=``.
Link: https://lkml.kernel.org/r/20241101165719.1074234-3-mcanal@igalia.com
Fixes: dd4d30d1cdbe ("mm: override mTHP "enabled" defaults at kernel cmdline")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Acked-by: Barry Song <baohua@kernel.org>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lance Yang <ioworker0@gmail.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
damon_feed_loop_next_input() is inefficient and fragile to overflows.
Specifically, 'score_goal_diff_bp' calculation can overflow when 'score'
is high. The calculation is actually unnecessary at all because 'goal' is
a constant of value 10,000. Calculation of 'compensation' is again
fragile to overflow. Final calculation of return value for under-achiving
case is again fragile to overflow when the current score is
under-achieving the target.
Add two corner cases handling at the beginning of the function to make the
body easier to read, and rewrite the body of the function to avoid
overflows and the unnecessary bp value calcuation.
Link: https://lkml.kernel.org/r/20241031161203.47751-1-sj@kernel.org
Fixes: 9294a037c015 ("mm/damon/core: implement goal-oriented feedback-driven quota auto-tuning")
Signed-off-by: SeongJae Park <sj@kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/944f3d5b-9177-48e7-8ec9-7f1331a3fea3@roeck-us.net
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: <stable@vger.kernel.org> [6.8.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
DAMON's logics to determine if this is the time to apply damos schemes
assumes next_apply_sis is always set larger than current
passed_sample_intervals. And therefore assume continuously incrementing
passed_sample_intervals will make it reaches to the next_apply_sis in
future. The logic hence does apply the scheme and update next_apply_sis
only if passed_sample_intervals is same to next_apply_sis.
If Schemes apply interval is set as zero, however, next_apply_sis is set
same to current passed_sample_intervals, respectively. And
passed_sample_intervals is incremented before doing the next_apply_sis
check. Hence, next_apply_sis becomes larger than next_apply_sis, and the
logic says it is not the time to apply schemes and update next_apply_sis.
In other words, DAMON stops applying schemes until passed_sample_intervals
overflows.
Based on the documents and the common sense, a reasonable behavior for
such inputs would be applying the schemes for every sampling interval.
Handle the case by removing the assumption.
Link: https://lkml.kernel.org/r/20241031183757.49610-3-sj@kernel.org
Fixes: 42f994b71404 ("mm/damon/core: implement scheme-specific apply interval")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> [6.7.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "mm/damon/core: fix handling of zero non-sampling intervals".
DAMON's internal intervals accounting logic is not correctly handling
non-sampling intervals of zero values for a wrong assumption. This could
cause unexpected monitoring behavior, and even result in infinite hang of
DAMON sysfs interface user threads in case of zero aggregation interval.
Fix those by updating the intervals accounting logic. For details of the
root case and solutions, please refer to commit messages of fixes.
This patch (of 2):
DAMON's logics to determine if this is the time to do aggregation and ops
update assumes next_{aggregation,ops_update}_sis are always set larger
than current passed_sample_intervals. And therefore it further assumes
continuously incrementing passed_sample_intervals every sampling interval
will make it reaches to the next_{aggregation,ops_update}_sis in future.
The logic therefore make the action and update
next_{aggregation,ops_updaste}_sis only if passed_sample_intervals is same
to the counts, respectively.
If Aggregation interval or Ops update interval are zero, however,
next_aggregation_sis or next_ops_update_sis are set same to current
passed_sample_intervals, respectively. And passed_sample_intervals is
incremented before doing the next_{aggregation,ops_update}_sis check.
Hence, passed_sample_intervals becomes larger than
next_{aggregation,ops_update}_sis, and the logic says it is not the time
to do the action and update next_{aggregation,ops_update}_sis forever,
until an overflow happens. In other words, DAMON stops doing aggregations
or ops updates effectively forever, and users cannot get monitoring
results.
Based on the documents and the common sense, a reasonable behavior for
such inputs is doing an aggregation and an ops update for every sampling
interval. Handle the case by removing the assumption.
Note that this could incur particular real issue for DAMON sysfs interface
users, in case of zero Aggregation interval. When user starts DAMON with
zero Aggregation interval and asks online DAMON parameter tuning via DAMON
sysfs interface, the request is handled by the aggregation callback.
Until the callback finishes the work, the user who requested the online
tuning just waits. Hence, the user will be stuck until the
passed_sample_intervals overflows.
Link: https://lkml.kernel.org/r/20241031183757.49610-1-sj@kernel.org
Link: https://lkml.kernel.org/r/20241031183757.49610-2-sj@kernel.org
Fixes: 4472edf63d66 ("mm/damon/core: use number of passed access sampling as a timer")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> [6.7.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
After commit 94d7d9233951 ("mm: abstract the vma_merge()/split_vma()
pattern for mprotect() et al."), if vma_modify_flags() return error, the
vma is set to an error code. This will lead to an invalid prev be
returned.
Generally this shouldn't matter as the caller should treat an error as
indicating state is now invalidated, however unfortunately
apply_mlockall_flags() does not check for errors and assumes that
mlock_fixup() correctly maintains prev even if an error were to occur.
This patch fixes that assumption.
[lorenzo.stoakes@oracle.com: provide a better fix and rephrase the log]
Link: https://lkml.kernel.org/r/20241027123321.19511-1-richard.weiyang@gmail.com
Fixes: 94d7d9233951 ("mm: abstract the vma_merge()/split_vma() pattern for mprotect() et al.")
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jann Horn <jannh@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Since gfp & GFP_ATOMIC == GFP_ATOMIC is true for GFP_KERNEL | GFP_HIGH, it
will use kmalloc if user specifies that combination. Here the reason why
combining the __vmalloc_node() and kmalloc_node() is that the vmalloc does
not support all GFP flag, especially GFP_ATOMIC. So we should check if
gfp & (GFP_ATOMIC | GFP_KERNEL) != GFP_ATOMIC for vmalloc first. This
ensures caller can sleep. And for the robustness, even if vmalloc fails,
it should retry with kmalloc to allocate it.
Link: https://lkml.kernel.org/r/173008598713.1262174.2959179484209897252.stgit@mhiramat.roam.corp.google.com
Fixes: aff1871bfc81 ("objpool: fix choosing allocation for percpu slots")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Closes: https://lore.kernel.org/all/CAHk-=whO+vSH+XVRio8byJU8idAWES0SPGVZ7KAVdc4qrV0VUA@mail.gmail.com/
Cc: Leo Yan <leo.yan@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Wu <wuqiang.matt@bytedance.com>
Cc: Mikel Rychliski <mikel@mikelr.com>
Cc: Steven Rostedt (Google) <rostedt@goodmis.org>
Cc: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
OOM kills due to vastly overestimated free highatomic reserves were
observed:
... invoked oom-killer: gfp_mask=0x100cca(GFP_HIGHUSER_MOVABLE), order=0 ...
Node 0 Normal free:1482936kB boost:0kB min:410416kB low:739404kB high:1068392kB reserved_highatomic:1073152KB ...
Node 0 Normal: 1292*4kB (ME) 1920*8kB (E) 383*16kB (UE) 220*32kB (ME) 340*64kB (E) 2155*128kB (UE) 3243*256kB (UE) 615*512kB (U) 1*1024kB (M) 0*2048kB 0*4096kB = 1477408kB
The second line above shows that the OOM kill was due to the following
condition:
free (1482936kB) - reserved_highatomic (1073152kB) = 409784KB < min (410416kB)
And the third line shows there were no free pages in any
MIGRATE_HIGHATOMIC pageblocks, which otherwise would show up as type 'H'.
Therefore __zone_watermark_unusable_free() underestimated the usable free
memory by over 1GB, which resulted in the unnecessary OOM kill above.
The comments in __zone_watermark_unusable_free() warns about the potential
risk, i.e.,
If the caller does not have rights to reserves below the min
watermark then subtract the high-atomic reserves. This will
over-estimate the size of the atomic reserve but it avoids a search.
However, it is possible to keep track of free pages in reserved highatomic
pageblocks with a new per-zone counter nr_free_highatomic protected by the
zone lock, to avoid a search when calculating the usable free memory. And
the cost would be minimal, i.e., simple arithmetics in the highatomic
alloc/free/move paths.
Note that since nr_free_highatomic can be relatively small, using a
per-cpu counter might cause too much drift and defeat its purpose, in
addition to the extra memory overhead.
Dependson e0932b6c1f94 ("mm: page_alloc: consolidate free page accounting") - see [1]
[akpm@linux-foundation.org: s/if/else if/, per Johannes, stealth whitespace tweak]
Link: https://lkml.kernel.org/r/20241028182653.3420139-1-yuzhao@google.com
Link: https://lkml.kernel.org/r/0d0ddb33-fcdc-43e2-801f-0c1df2031afb@suse.cz [1]
Fixes: 0aaa29a56e4f ("mm, page_alloc: reserve pageblocks for high-order atomic allocations on demand")
Signed-off-by: Yu Zhao <yuzhao@google.com>
Reported-by: Link Lin <linkl@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
If we error in data_update_init() after adding to the rhashtable of
outstanding promotes, kfree_rcu() is required.
Reported-by: Reed Riley <reed@riley.engineer>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Change OPT_STR max value to be 1 less than the "ARRAY_SIZE" of "_choices"
array. As a result, remove -1 from (opt->max-1) in bch2_opt_to_text.
The "_choices" array is a null-terminated array, so computing the maximum
using "ARRAY_SIZE" without subtracting 1 yields an incorrect result. Since
bch2_opt_validate don't subtract 1, as bch2_opt_to_text does, values
bigger than the actual maximum would pass through option validation.
Reported-by: syzbot+bee87a0c3291c06aa8c6@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=bee87a0c3291c06aa8c6
Fixes: 63c4b2545382 ("bcachefs: Better superblock opt validation")
Suggested-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Piotr Zalewski <pZ010001011111@proton.me>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
When allocating new btree nodes, we were leaving them on the freeable
list - unlocked - allowing them to be reclaimed: ouch.
Additionally, bch2_btree_node_free_never_used() ->
bch2_btree_node_hash_remove was putting it on the freelist, while
bch2_btree_node_free_never_used() was putting it back on the btree
update reserve list - ouch.
Originally, the code was written to always keep btree nodes on a list -
live or freeable - and this worked when new nodes were kept locked.
But now with the cycle detector, we can't keep nodes locked that aren't
tracked by the cycle detector; and this is fine as long as they're not
reachable.
We also have better and more robust leak detection now, with memory
allocation profiling, so the original justification no longer applies.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
The perf_test does not check the number of iterations and threads
when it is zero. If nr_thread is 0, the perf test will keep
waiting for wakekup. If iteration is 0, it will cause exception
of division by zero. This can be reproduced by:
echo "rand_insert 0 1" > /sys/fs/bcachefs/${uuid}/perf_test
or
echo "rand_insert 1 0" > /sys/fs/bcachefs/${uuid}/perf_test
Fixes: 1c6fdbd8f246 ("bcachefs: Initial commit")
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
bio_kmalloc may return NULL, will cause NULL pointer dereference.
Add check NULL return for bio_kmalloc in journal_read_bucket.
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Fixes: ac10a9611d87 ("bcachefs: Some fixes for building in userspace")
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
If BCH_FS_may_go_rw is not yet set, it indicates to the transaction
commit path that updates should be done via the list of journal replay
keys.
This must be set before multithreaded use commences.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
If a btree split picks a pivot that's being deleted by a btree node
merge, we're going to have problems.
Fix this by checking if the pivot is being deleted, the same as we check
for deletions in journal replay keys.
Found by single_devic.ktest small_nodes.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Syzbot found an assertion pop, by generating an ancient filesystem
version with an invalid bkey_format (with fields that can overflow) as
well as packed keys that aren't representable unpacked.
This breaks key comparisons in all sorts of painful ways.
Filesystems have been automatically rewriting nodes with such invalid
formats for years; we can safely drop support for them.
Reported-by: syzbot+8a0109511de9d4b61217@syzkaller.appspotmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
bucket_gen() checks if we're lookup up a valid bucket and returns NULL
otherwise, but bucket_gen_get() was failing to check; other callers were
correct.
Also do a bit of cleanup on callers.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from can and netfilter.
Things are slowing down quite a bit, mostly driver fixes here. No
known ongoing investigations.
Current release - new code bugs:
- eth: ti: am65-cpsw:
- fix multi queue Rx on J7
- fix warning in am65_cpsw_nuss_remove_rx_chns()
Previous releases - regressions:
- mptcp: do not require admin perm to list endpoints, got missed in a
refactoring
- mptcp: use sock_kfree_s instead of kfree
Previous releases - always broken:
- sctp: properly validate chunk size in sctp_sf_ootb() fix OOB access
- virtio_net: make RSS interact properly with queue number
- can: mcp251xfd: mcp251xfd_get_tef_len(): fix length calculation
- can: mcp251xfd: mcp251xfd_ring_alloc(): fix coalescing
configuration when switching CAN modes
Misc:
- revert earlier hns3 fixes, they were ignoring IOMMU abstractions
and need to be reworked
- can: {cc770,sja1000}_isa: allow building on x86_64"
* tag 'net-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (42 commits)
drivers: net: ionic: add missed debugfs cleanup to ionic_probe() error path
net/smc: do not leave a dangling sk pointer in __smc_create()
rxrpc: Fix missing locking causing hanging calls
net/smc: Fix lookup of netdev by using ib_device_get_netdev()
net: arc: rockchip: fix emac mdio node support
net: arc: fix the device for dma_map_single/dma_unmap_single
virtio_net: Update rss when set queue
virtio_net: Sync rss config to device when virtnet_probe
virtio_net: Add hash_key_length check
virtio_net: Support dynamic rss indirection table size
netfilter: nf_tables: wait for rcu grace period on net_device removal
net: stmmac: Fix unbalanced IRQ wake disable warning on single irq case
net: vertexcom: mse102x: Fix possible double free of TX skb
mptcp: use sock_kfree_s instead of kfree
mptcp: no admin perm to list endpoints
net: phy: ti: add PHY_RST_AFTER_CLK_EN flag
net: ethernet: ti: am65-cpsw: fix warning in am65_cpsw_nuss_remove_rx_chns()
net: ethernet: ti: am65-cpsw: Fix multi queue Rx on J7
net: hns3: fix kernel crash when uninstalling driver
Revert "Merge branch 'there-are-some-bugfix-for-the-hns3-ethernet-driver'"
...
|
|
Pull NVMe fix from Keith:
"nvme fix for Linux 6.13
- Use correct list traversal for srcu lists (Breno)"
* tag 'nvme-6.12-2024-11-07' of git://git.infradead.org/nvme:
nvme/host: Fix RCU list traversal to use SRCU primitive
|
|
The ionic_setup_one() creates a debugfs entry for ionic upon
successful execution. However, the ionic_probe() does not
release the dentry before returning, resulting in a memory
leak.
To fix this bug, we add the ionic_debugfs_del_dev() to release
the resources in a timely manner before returning.
Fixes: 0de38d9f1dba ("ionic: extract common bits from ionic_probe")
Signed-off-by: Wentao Liang <Wentao_liang_g@163.com>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://patch.msgid.link/20241107021756.1677-1-liangwentao@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Thanks to commit 4bbd360a5084 ("socket: Print pf->create() when
it does not clear sock->sk on failure."), syzbot found an issue with AF_SMC:
smc_create must clear sock->sk on failure, family: 43, type: 1, protocol: 0
WARNING: CPU: 0 PID: 5827 at net/socket.c:1565 __sock_create+0x96f/0xa30 net/socket.c:1563
Modules linked in:
CPU: 0 UID: 0 PID: 5827 Comm: syz-executor259 Not tainted 6.12.0-rc6-next-20241106-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:__sock_create+0x96f/0xa30 net/socket.c:1563
Code: 03 00 74 08 4c 89 e7 e8 4f 3b 85 f8 49 8b 34 24 48 c7 c7 40 89 0c 8d 8b 54 24 04 8b 4c 24 0c 44 8b 44 24 08 e8 32 78 db f7 90 <0f> 0b 90 90 e9 d3 fd ff ff 89 e9 80 e1 07 fe c1 38 c1 0f 8c ee f7
RSP: 0018:ffffc90003e4fda0 EFLAGS: 00010246
RAX: 099c6f938c7f4700 RBX: 1ffffffff1a595fd RCX: ffff888034823c00
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 00000000ffffffe9 R08: ffffffff81567052 R09: 1ffff920007c9f50
R10: dffffc0000000000 R11: fffff520007c9f51 R12: ffffffff8d2cafe8
R13: 1ffffffff1a595fe R14: ffffffff9a789c40 R15: ffff8880764298c0
FS: 000055557b518380(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa62ff43225 CR3: 0000000031628000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
sock_create net/socket.c:1616 [inline]
__sys_socket_create net/socket.c:1653 [inline]
__sys_socket+0x150/0x3c0 net/socket.c:1700
__do_sys_socket net/socket.c:1714 [inline]
__se_sys_socket net/socket.c:1712 [inline]
For reference, see commit 2d859aff775d ("Merge branch
'do-not-leave-dangling-sk-pointers-in-pf-create-functions'")
Fixes: d25a92ccae6b ("net/smc: Introduce IPPROTO_SMC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ignat Korchagin <ignat@cloudflare.com>
Cc: D. Wythe <alibuda@linux.alibaba.com>
Cc: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://patch.msgid.link/20241106221922.1544045-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a call gets aborted (e.g. because kafs saw a signal) between it being
queued for connection and the I/O thread picking up the call, the abort
will be prioritised over the connection and it will be removed from
local->new_client_calls by rxrpc_disconnect_client_call() without a lock
being held. This may cause other calls on the list to disappear if a race
occurs.
Fix this by taking the client_call_lock when removing a call from whatever
list its ->wait_link happens to be on.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Fixes: 9d35d880e0e4 ("rxrpc: Move client call connection to the I/O thread")
Link: https://patch.msgid.link/726660.1730898202@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SMC-R variant of the SMC protocol used direct call to function
ib_device_ops.get_netdev() to lookup netdev. As we used mlx5 device
driver to run SMC-R, it failed to find a device, because in mlx5_ib the
internal net device management for retrieving net devices was replaced
by a common interface ib_device_get_netdev() in commit 8d159eb2117b
("RDMA/mlx5: Use IB set_netdev and get_netdev functions").
Since such direct accesses to the internal net device management is not
recommended at all, update the SMC-R code to use proper API
ib_device_get_netdev().
Fixes: 54903572c23c ("net/smc: allow pnetid-less configuration")
Reported-by: Aswin K <aswin@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://patch.msgid.link/20241106082612.57803-1-wenjia@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fix from Uwe Kleine-König:
"Fix period setting in imx-tpm driver and a maintainer update
Erik Schumacher found and fixed a problem in the calculation of the
PWM period setting yielding too long periods. Trevor Gamblin - who
already cared about mainlining the pwm-axi-pwmgen driver - stepped
forward as an additional reviewer.
Thanks to Erik and Trevor"
* tag 'pwm/for-6.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
MAINTAINERS: add self as reviewer for AXI PWM GENERATOR
pwm: imx-tpm: Use correct MODULO value for EPWM mode
|
|
seq_printf is costy, on a system with n CPUs, reading /proc/softirqs
would yield 10*n decimal values, and the extra cost parsing format string
grows linearly with number of cpus. Replace seq_printf with
seq_put_decimal_ull_width have significant performance improvement.
On an 8CPUs system, reading /proc/softirqs show ~40% performance
gain with this patch.
Signed-off-by: David Wang <00107082@163.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current panthor_device_mmap_io() implementation has two issues:
1. For mapping DRM_PANTHOR_USER_FLUSH_ID_MMIO_OFFSET,
panthor_device_mmap_io() bails if VM_WRITE is set, but does not clear
VM_MAYWRITE. That means userspace can use mprotect() to make the mapping
writable later on. This is a classic Linux driver gotcha.
I don't think this actually has any impact in practice:
When the GPU is powered, writes to the FLUSH_ID seem to be ignored; and
when the GPU is not powered, the dummy_latest_flush page provided by the
driver is deliberately designed to not do any flushes, so the only thing
writing to the dummy_latest_flush could achieve would be to make *more*
flushes happen.
2. panthor_device_mmap_io() does not block MAP_PRIVATE mappings (which are
mappings without the VM_SHARED flag).
MAP_PRIVATE in combination with VM_MAYWRITE indicates that the VMA has
copy-on-write semantics, which for VM_PFNMAP are semi-supported but
fairly cursed.
In particular, in such a mapping, the driver can only install PTEs
during mmap() by calling remap_pfn_range() (because remap_pfn_range()
wants to **store the physical address of the mapped physical memory into
the vm_pgoff of the VMA**); installing PTEs later on with a fault
handler (as panthor does) is not supported in private mappings, and so
if you try to fault in such a mapping, vmf_insert_pfn_prot() splats when
it hits a BUG() check.
Fix it by clearing the VM_MAYWRITE flag (userspace writing to the FLUSH_ID
doesn't make sense) and requiring VM_SHARED (copy-on-write semantics for
the FLUSH_ID don't make sense).
Reproducers for both scenarios are in the notes of my patch on the mailing
list; I tested that these bugs exist on a Rock 5B machine.
Note that I only compile-tested the patch, I haven't tested it; I don't
have a working kernel build setup for the test machine yet. Please test it
before applying it.
Cc: stable@vger.kernel.org
Fixes: 5fe909cae118 ("drm/panthor: Add the device logical block")
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241105-panthor-flush-page-fixes-v1-1-829aaf37db93@google.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fix for net
The following series contains a Netfilter fix:
1) Wait for rcu grace period after netdevice removal is reported via event.
* tag 'nf-24-11-07' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: wait for rcu grace period on net_device removal
====================
Link: https://patch.msgid.link/20241107113212.116634-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Write the size of the optional payload of SOF_IPC4_MOD_INIT_INSTANCE
message to extension param_size-bits.
The previous IPC4 version does not set these bits that should indicate
the size of the optional payload (struct sof_ipc4_probe_cfg). The old
firmware side component code works well without these bits, but when
the probes are converted to use the generic module API, this does not
work anymore.
Fixes: f5623593060f ("ASoC: SOF: IPC4: probes: Implement IPC4 ops for probes client device")
Signed-off-by: Jyri Sarha <jyri.sarha@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20241107132840.17386-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Similar to commit cac075706f29 ("drm/panthor: Fix race when converting
group handle to group object") we need to use the XArray's internal
locking when retrieving a vm pointer from there.
v2: Removed part of the patch that was trying to protect fetching
the heap pointer from XArray, as that operation is protected by
the @pool->lock.
Fixes: 647810ec2476 ("drm/panthor: Add the MMU/VM logical block")
Reported-by: Jann Horn <jannh@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241106185806.389089-1-liviu.dudau@arm.com
|
|
There are 2G and 4G RAM versions of the Lenovo Yoga Tab 3 X90F and it
turns out that the 2G version has a DMI product name of
"CHERRYVIEW D1 PLATFORM" where as the 4G version has
"CHERRYVIEW C0 PLATFORM". The sys-vendor + product-version check are
unique enough that the product-name check is not necessary.
Drop the product-name check so that the existing DMI match for the 4G
RAM version also matches the 2G RAM version.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240825132131.6643-1-hdegoede@redhat.com
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
thunderbolt: Fixes for v6.12-rc7
This includes following USB4/Thunderbolt fixes for v6.12-rc7:
- Fix for retimer enumeration.
- Fix connection issue with Pluggable UD-4VPD USB4 dock.
Both have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix connection issue with Pluggable UD-4VPD dock
thunderbolt: Add only on-board retimers when !CONFIG_USB4_DEBUGFS_MARGINING
|
|
I noticed that recently, simple operations like "make" started
failing on NFSv3 mounts of ext4 exports. Network capture shows that
READDIRPLUS operated correctly but READDIR failed with
NFS3ERR_INVAL. The vfs_llseek() call returned EINVAL when it is
passed a non-zero starting directory cookie.
I bisected to commit c689bdd3bffa ("nfsd: further centralize
protocol version checks.").
Turns out that nfsd3_proc_readdir() does not call fh_verify() before
it calls nfsd_readdir(), so the new fhp->fh_64bit_cookies boolean is
not set properly. This leaves the NFSD_MAY_64BIT_COOKIE unset when
the directory is opened.
For ext4, this causes the wrong "max file size" value to be used
when sanity checking the incoming directory cookie (which is a seek
offset value).
The fhp->fh_64bit_cookies boolean is /always/ properly initialized
after nfsd_open() returns. There doesn't seem to be a reason for the
generic NFSD open helper to handle the f_mode fix-up for
directories, so just move that to the one caller that tries to open
an S_IFDIR with NFSD_MAY_64BIT_COOKIE.
Suggested-by: NeilBrown <neilb@suse.de>
Fixes: c689bdd3bffa ("nfsd: further centralize protocol version checks.")
Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
This patch checks if div is less than or equal to zero (div <= 0). If
div is zero or negative, the function returns -EINVAL, ensuring the
division operation is safe to perform.
Signed-off-by: Luo Yifan <luoyifan@cmss.chinamobile.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://patch.msgid.link/20241107015936.211902-1-luoyifan@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch checks if div is less than or equal to zero (div <= 0). If
div is zero or negative, the function returns -EINVAL, ensuring the
division operation (*prate / div) is safe to perform.
Signed-off-by: Luo Yifan <luoyifan@cmss.chinamobile.com>
Link: https://patch.msgid.link/20241106014654.206860-1-luoyifan@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Another model of Thinkpad E14 Gen 6 (21M4)
needs a quirk entry for the dmic to be detected.
Signed-off-by: Markus Petri <mp@mpetri.org>
Link: https://patch.msgid.link/20241107094020.1050935-1-mp@localhost
Signed-off-by: Mark Brown <broonie@kernel.org>
|
