| Age | Commit message (Collapse) | Author |
|---|
|
The i40e driver was causing a kernel panic when
non-contiguous Traffic Classes, or Traffic Classes not
starting with TC0, were configured on a link partner switch.
i40e does not support non-contiguous TCs.
To fix this, the patch changes the logic when determining
the total number of TCs enabled. Before, this would use the
highest TC number enabled and assume that all TCs below it were
also enabled. Now, we create a bitmask of enabled TCs and scan
it to determine not only the number of TCs, but also if the set
of enabled TCs starts at zero and is contiguous. If not, then
DCB is disabled by only returning one TC.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
attempt_restore_of_faulty_devices() is limited to 64 when it should support
the new maximum of 253 when identifying any failed devices. It clears any
revivable devices via an MD personality hot remove and add cylce to allow
for their recovery.
Address by using existing functions to retrieve and update all failed
devices' bitfield members in the dm raid superblocks on all RAID devices
and check for any devices to clear in it.
Whilst on it, don't call attempt_restore_of_faulty_devices() for any MD
personality not providing disk hot add/remove methods (i.e. raid0 now),
because such personalities don't support reviving of failed disks.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
'lvchange --refresh RaidLV' causes a mapped device suspend/resume cycle
aiming at device restore and resync after transient device failures. This
failed because flag RT_FLAG_RS_RESUMED was always cleared in the suspend path,
thus the device restore wasn't performed in the resume path.
Solve by removing RT_FLAG_RS_RESUMED from the suspend path and resume
unconditionally. Also, remove superfluous comment from raid_resume().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 16369564915a ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On LVM2 conversions via lvconvert(8), the target keeps mapped devices in
frozen state when requesting RAID devices be resynchronized. This
applies to e.g. adding legs to a raid1 device or taking over from raid0
to raid4 when the rebuild flag's set on the new raid1 legs or the added
dedicated parity stripe.
Also, fix frozen recovery for reshaping as well.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are a few pin control fixes for the v4.8 series, nothing special
about them:
- Add the missing <linux/io.h> header to the Intel Merrifield driver
to get rid of build mess.
- Drop two instances of pinctrl_unregister() called for drivers using
devm_* resource management.
- Remove the default debounce time for the AMD driver"
* tag 'pinctrl-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: intel: merrifield: Add missed header
pinctrl/amd: Remove the default de-bounce time
pinctrl: pistachio: Drop pinctrl_unregister for devm_ registered device
pinctrl: meson: Drop pinctrl_unregister for devm_ registered device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix occasional decoding errors when tracing system-wide with
Intel PT (Adrian Hunter)
- Fix ip compression in Intel PT for some specific packet types not
present on current hardware (Adrian Hunter)
- Fix annotation of objects with debuginfo files (Anton Blanchard)
- Fix build on Fedora Rawhide (25) wrt using the right header to
get the major() & minor() definitions in the jitdump code, now
it is deprecated getting those using sys/types.h, one has to use
sys/sysmacros.h (Arnaldo Carvalho de Melo)
- Sync arm64/s390 kvm related header files (Arnaldo Carvalho de Melo)
- Check for dup and fdopen failures in 'perf probe' (Colin Ian King,
Arnaldo Carvalho de Melo)
- Fix showing callchains in pipe mode, i.e.
perf record -g -o - workload | perf script
now shows callchains (He Kuang)
- Show proper message when the scripts directory points to some
invalid location in 'perf script --list' (He Kuang)
- Fix 'perf mem -t store' to record 'cpu/mem-stores/P' events
again (Jiri Olsa)
- Fix ppc64le build failure when libelf is not present (Ravi Bangoria)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is prepatory work for an expanding list of adapter families that have
occasional ~10 hour clock jumps when being used for PTP. Factor out the
sanitization function and convert to using a feature (bug) flag, per
suggestion from Jesse Brandeburg.
Littering functional code with device-specific checks is much messier than
simply checking a flag, and having device-specific init set flags as needed.
There are probably a number of other cases in the e1000e code that
could/should be converted similarly.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and
igb_ptp_rx_rgtstamp. Add PHY delay compensation in
igb_ptp_rx_pktstamp().
In the IGB driver, there are two functions that retrieve timestamps
received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp().
The previous commit only changed igb_ptp_rx_rgtstamp(), and the change
was incorrect.
There are two instances in which PHY delay compensations should be
made:
- Before the packet transmission over the PHY, the latency between
when the packet is timestamped and transmission of the packets,
should be an add operation, but it is currently a subtract.
- After the packets are received from the PHY, the latency between
the receiving and timestamping of the packets should be a subtract
operation, but it is currently an add.
Signed-off-by: Kshitiz Gupta <kshitiz.gupta@ni.com>
Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency)
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The GART aperture size can be bigger than 4GB. Therefore the offset
used in amdgpu_gart_bind and amdgpu_gart_unbind must be 64-bit.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
rtree_next_node() walks the linked list of leaf nodes to find the next
block of pages in the struct memory_bitmap. If it walks off the end of
the list of nodes, it walks the list of memory zones to find the next
region of memory. If it walks off the end of the list of zones, it
returns false.
This leaves the struct bm_position's node and zone pointers pointing
at their respective struct list_heads in struct mem_zone_bm_rtree.
memory_bm_find_bit() uses struct bm_position's node and zone pointers
to avoid walking lists and trees if the next bit appears in the same
node/zone. It handles these values being stale.
Swap rtree_next_node()s 'step then test' to 'test-next then step',
this means if we reach the end of memory we return false and leave
the node and zone pointers as they were.
This fixes a panic on resume using AMD Seattle with 64K pages:
[ 6.868732] Freezing user space processes ... (elapsed 0.000 seconds) done.
[ 6.875753] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds)
[ 6.896453] PM: Using 3 thread(s) for decompression.
[ 6.896453] PM: Loading and decompressing image data (5339 pages)...
[ 7.318890] PM: Image loading progress: 0%
[ 7.323395] Unable to handle kernel paging request at virtual address 00800040
[ 7.330611] pgd = ffff000008df0000
[ 7.334003] [00800040] *pgd=00000083fffe0003, *pud=00000083fffe0003, *pmd=00000083fffd0003, *pte=0000000000000000
[ 7.344266] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 7.349825] Modules linked in:
[ 7.352871] CPU: 2 PID: 1 Comm: swapper/0 Tainted: G W I 4.8.0-rc1 #4737
[ 7.360512] Hardware name: AMD Overdrive/Supercharger/Default string, BIOS ROD1002C 04/08/2016
[ 7.369109] task: ffff8003c0220000 task.stack: ffff8003c0280000
[ 7.375020] PC is at set_bit+0x18/0x30
[ 7.378758] LR is at memory_bm_set_bit+0x24/0x30
[ 7.383362] pc : [<ffff00000835bbc8>] lr : [<ffff0000080faf18>] pstate: 60000045
[ 7.390743] sp : ffff8003c0283b00
[ 7.473551]
[ 7.475031] Process swapper/0 (pid: 1, stack limit = 0xffff8003c0280020)
[ 7.481718] Stack: (0xffff8003c0283b00 to 0xffff8003c0284000)
[ 7.800075] Call trace:
[ 7.887097] [<ffff00000835bbc8>] set_bit+0x18/0x30
[ 7.891876] [<ffff0000080fb038>] duplicate_memory_bitmap.constprop.38+0x54/0x70
[ 7.899172] [<ffff0000080fcc40>] snapshot_write_next+0x22c/0x47c
[ 7.905166] [<ffff0000080fe1b4>] load_image_lzo+0x754/0xa88
[ 7.910725] [<ffff0000080ff0a8>] swsusp_read+0x144/0x230
[ 7.916025] [<ffff0000080fa338>] load_image_and_restore+0x58/0x90
[ 7.922105] [<ffff0000080fa660>] software_resume+0x2f0/0x338
[ 7.927752] [<ffff000008083350>] do_one_initcall+0x38/0x11c
[ 7.933314] [<ffff000008b40cc0>] kernel_init_freeable+0x14c/0x1ec
[ 7.939395] [<ffff0000087ce564>] kernel_init+0x10/0xfc
[ 7.944520] [<ffff000008082e90>] ret_from_fork+0x10/0x40
[ 7.949820] Code: d2800022 8b400c21 f9800031 9ac32043 (c85f7c22)
[ 7.955909] ---[ end trace 0024a5986e6ff323 ]---
[ 7.960529] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Here struct mem_zone_bm_rtree's start_pfn has been returned instead of
struct rtree_node's addr as the node/zone pointers are corrupt after
we walked off the end of the lists during mark_unsafe_pages().
This behaviour was exposed by commit 6dbecfd345a6 ("PM / hibernate:
Simplify mark_unsafe_pages()"), which caused mark_unsafe_pages() to call
duplicate_memory_bitmap(), which uses memory_bm_find_bit() after walking
off the end of the memory bitmap.
Fixes: 3a20cb177961 (PM / Hibernate: Implement position keeping in radix tree)
Signed-off-by: James Morse <james.morse@arm.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719a5 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sean Wang says:
====================
mediatek: Fix warning and issue
This patch set fixes the following warning and issues
v1 -> v2: Fix message typos and add coverletter
v2 -> v3: Split from the previous series for submitting bug fixes
as a series targeting 'net'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
device pointers passed to DMA API
Runtime warning occurs if DMA-API debug feature is enabled that would be
raised by pointers passed to DMA API as arguments to inconsistent struct
device objects, so that the patch makes them usage aligned between DMA
operations such as dma_map_*() and dma_unmap_*() to eliminate the warning.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enabled properly
Commit 08ef55c6f257acf3bdc6940813f80e8f0f5d90ec
("net-next: mediatek: fix gigabit and flow control advertisement")
had supported proper flow control settings for GMAC1. But for GMAC0,
1.GMAC0 shares the common logic with GMAC1 inside mtk_phy_link_adjust()
to adapt various settings for the target phy.
2.GMAC0 uses fixed-phy to connect to a builtin gigabit switch with
fixed link speed as commit 0c72c50f6f93b0c3daa9ea35d89ab3a933c7b5a0
("net-next: mediatek: add fixed-phy support") describes.
3.However, fixed-phy doesn't enable SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flag on default that would cause mtk_phy_link_adjust() not to
enable flow control setting on GMAC0 properly and cause packet dropped
when high traffic.
Due to these reasons, the patch adds SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flags on fixed-phy used by the driver to have proper handling on
the both GMAC with the shared common logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch fixes up the incorrect setup of reduced MII (RMII) on GMAC
and adds the supplement for the setup of reverse MII (REVMII) on GMAC
, and rearranges the error handling for invalid PHY argument.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The value of temp_level4_pgt is the physical address of the
top-level page directory, so use __pa() to compute it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
|
|
In order to successfully decode Intel PT traces, context switch events
are needed from the moment the trace starts. Currently that is ensured
by using the 'immediate' flag which enables the switch event when it is
opened.
However, since commit 86c2786994bd ("perf intel-pt: Add support for
PERF_RECORD_SWITCH") that might not always happen. When tracing
system-wide the context switch event is added to the tracking event
which was not set as 'immediate'. Change that so it is.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 86c2786994bd ("perf intel-pt: Add support for PERF_RECORD_SWITCH")
Link: http://lkml.kernel.org/r/1471245784-22580-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
From a quick look nothing stands out as requiring changes to kvm tools
such as tools/perf/arch/s390/util/kvm-stat.c.
Silences these header checking warnings:
$ make -C tools/perf
make: Entering directory '/home/acme/git/linux/tools/perf'
BUILD: Doing 'make -j4' parallel build
Warning: tools/arch/s390/include/uapi/asm/kvm.h differs from kernel
Warning: tools/arch/s390/include/uapi/asm/sie.h differs from kernel
Warning: tools/arch/arm64/include/uapi/asm/kvm.h differs from kernel
<SNIP>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hemant Kumar <hemant@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-btutge414g516qmh6r5ienlj@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Colin King <colin.king@canonical.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-zh2j4iqimralugke5qq7dn6d@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add missing platform_set_drvdata() in tps65217_charger_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Fixes: 3636859b280c ("power_supply: Add support for tps65217-charger")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
tipc_msg_create() can return a NULL skb and if so, we shouldn't try to
call tipc_node_xmit_skb() on it.
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 3 PID: 30298 Comm: trinity-c0 Not tainted 4.7.0-rc7+ #19
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
task: ffff8800baf09980 ti: ffff8800595b8000 task.ti: ffff8800595b8000
RIP: 0010:[<ffffffff830bb46b>] [<ffffffff830bb46b>] tipc_node_xmit_skb+0x6b/0x140
RSP: 0018:ffff8800595bfce8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000003023b0e0
RDX: 0000000000000000 RSI: dffffc0000000000 RDI: ffffffff83d12580
RBP: ffff8800595bfd78 R08: ffffed000b2b7f32 R09: 0000000000000000
R10: fffffbfff0759725 R11: 0000000000000000 R12: 1ffff1000b2b7f9f
R13: ffff8800595bfd58 R14: ffffffff83d12580 R15: dffffc0000000000
FS: 00007fcdde242700(0000) GS:ffff88011af80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fcddde1db10 CR3: 000000006874b000 CR4: 00000000000006e0
DR0: 00007fcdde248000 DR1: 00007fcddd73d000 DR2: 00007fcdde248000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000090602
Stack:
0000000000000018 0000000000000018 0000000041b58ab3 ffffffff83954208
ffffffff830bb400 ffff8800595bfd30 ffffffff8309d767 0000000000000018
0000000000000018 ffff8800595bfd78 ffffffff8309da1a 00000000810ee611
Call Trace:
[<ffffffff830c84a3>] tipc_shutdown+0x553/0x880
[<ffffffff825b4a3b>] SyS_shutdown+0x14b/0x170
[<ffffffff8100334c>] do_syscall_64+0x19c/0x410
[<ffffffff83295ca5>] entry_SYSCALL64_slow_path+0x25/0x25
Code: 90 00 b4 0b 83 c7 00 f1 f1 f1 f1 4c 8d 6d e0 c7 40 04 00 00 00 f4 c7 40 08 f3 f3 f3 f3 48 89 d8 48 c1 e8 03 c7 45 b4 00 00 00 00 <80> 3c 30 00 75 78 48 8d 7b 08 49 8d 75 c0 48 b8 00 00 00 00 00
RIP [<ffffffff830bb46b>] tipc_node_xmit_skb+0x6b/0x140
RSP <ffff8800595bfce8>
---[ end trace 57b0484e351e71f1 ]---
I feel like we should maybe return -ENOMEM or -ENOBUFS, but I'm not sure
userspace is equipped to handle that. Anyway, this is better than a GPF
and looks somewhat consistent with other tipc_msg_create() callers.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vitaly Kuznetsov says:
====================
hv_netvsc: fixes for VF removal path
Kernel crash is reported after VF is removed and detached from netvsc
device. Turns out we have multiple different (but related) issues on the
VF removal path which I'm trying to address with PATCHes 2-5 of this
series. PATCH1 is required to support the change.
Changes since v1:
- Re-arrange patches in the series to not introduce new issues [David Miller]
- Add PATCH5 which fixes a new issue I discovered while testing.
- Add Haiyang' A-b tags to PATCH1-4
With regards to Stephen's suggestion: I believe that switching to using RCU
and eliminating vf_use_cnt/vf_inject is the right thing to do long-term, we
can either put this on top of this series or do it later in net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bonding driver sets IFF_BONDING on both master (the bonding device) and
slave (the real NIC) devices and in netvsc_netdev_event() we want to skip
master devices only. Currently, there is an uncertainty when a slave
interface is removed: if bonding module comes first in netdev_chain it
clears IFF_BONDING flag on the netdev and netvsc_netdev_event() correctly
handles NETDEV_UNREGISTER event, but in case netvsc comes first on the
chain it sees the device with IFF_BONDING still attached and skips it. As
we still hold vf_netdev pointer to the device we crash on the next inject.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're not guaranteed to see NETDEV_REGISTER/NETDEV_UNREGISTER notifications
only once per VF but we increase/decrease module refcount unconditionally.
Check vf_netdev to make sure we don't take/release it twice. We presume
that only one VF per netvsc device may exist.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We reset vf_inject on VF going down (netvsc_vf_down()) but we don't on
VF removal (netvsc_unregister_vf()) so vf_inject stays 'true' while
vf_netdev is already NULL and we're trying to inject packets into NULL
net device in netvsc_recv_callback() causing kernel to crash.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here is a deadlock scenario:
- netvsc_vf_up() schedules netvsc_notify_peers() work and quits.
- netvsc_vf_down() runs before netvsc_notify_peers() gets executed. As it
is being executed from netdev notifier chain we hold rtnl lock when we
get here.
- we enter while (atomic_read(&net_device_ctx->vf_use_cnt) != 0) loop and
wait till netvsc_notify_peers() drops vf_use_cnt.
- netvsc_notify_peers() starts on some other CPU but netdev_notify_peers()
will hang on rtnl_lock().
- deadlock!
Instead of introducing additional synchronization I suggest we drop
gwrk.dwrk completely and call NETDEV_NOTIFY_PEERS directly. As we're
acting under rtnl lock this is legitimate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct netvsc_device is not suitable for storing VF information as this
structure is being destroyed on MTU change / set channel operation (see
rndis_filter_device_remove()). Move all VF related stuff to struct
net_device_context which is persistent.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that the inner_protocol is set on transmit so that GSO segmentation,
which relies on that field, works correctly.
This is achieved by setting the inner_protocol in gre_build_header rather
than each caller of that function. It ensures that the inner_protocol is
set when gre_fb_xmit() is used to transmit GRE which was not previously the
case.
I have observed this is not the case when OvS transmits GRE using
lwtunnel metadata (which it always does).
Fixes: 38720352412a ("gre: Use inner_proto to obtain inner header protocol")
Cc: Pravin Shelar <pshelar@ovn.org>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dup and fdopen can potentially fail, so add some extra
error handling checks rather than assuming they always work.
Signed-off-by: Colin King <colin.king@canonical.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1471038296-12956-1-git-send-email-colin.king@canonical.com
[ Free resources when those functions (now being verified) fail ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Commit 73cdf0c6ea9c ("perf symbols: Record text offset in dso
to calculate objdump address") started storing the offset of
the text section for all DSOs:
if (elf_section_by_name(elf, &ehdr, &tshdr, ".text", NULL))
dso->text_offset = tshdr.sh_addr - tshdr.sh_offset;
Unfortunately this breaks debuginfo files, because we need to calculate
the offset of the text section in the associated executable file. As a
result perf annotate returns junk for all debuginfo files.
Fix this by using runtime_ss->elf which should point at the executable
when parsing a debuginfo file.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Tested-by: Wang Nan <wangnan0@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v4.6+
Fixes: 73cdf0c6ea9c ("perf symbols: Record text offset in dso to calculate objdump address")
Link: http://lkml.kernel.org/r/20160813115533.6de17912@kryten
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Some functions defined in a header file for the mediatek driver were
not marked inline. Fix that oversight.
- Fix a potential crash in the ARM64 dma-mapping code when freeing a
partially initialized domain.
- Another fix for ARM64 dma-mapping to respect IOMMU mapping
constraints when allocating IOVA addresses.
* tag 'iommu-fixes-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dma: Respect IOMMU aperture when allocating
iommu/dma: Don't put uninitialised IOVA domains
iommu/mediatek: Mark static functions in headers inline
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"A fix to sb_edac correcting channel reporting on Knights Landing"
* tag 'edac_fixes_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, sb_edac: Fix channel reporting on Knights Landing
|
|
ping_v6_sendmsg does not set flowi6_oif in response to
sin6_scope_id or sk_bound_dev_if, so it is not possible to use
these APIs to ping an IPv6 address on a different interface.
Instead, it sets flowi6_iif, which is incorrect but harmless.
Stop setting flowi6_iif, and support various ways of setting oif
in the same priority order used by udpv6_sendmsg.
Tested: https://android-review.googlesource.com/#/c/254470/
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I got this:
================================================================================
UBSAN: Undefined behaviour in ./include/linux/log2.h:63:13
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 1 PID: 721 Comm: kworker/1:1 Not tainted 4.8.0-rc1+ #87
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Workqueue: events rht_deferred_worker
0000000000000000 ffff88011661f8d8 ffffffff82344f50 0000000041b58ab3
ffffffff84f98000 ffffffff82344ea4 ffff88011661f900 ffff88011661f8b0
0000000000000001 ffff88011661f6b8 dffffc0000000000 ffffffff867f7640
Call Trace:
[<ffffffff82344f50>] dump_stack+0xac/0xfc
[<ffffffff82344ea4>] ? _atomic_dec_and_lock+0xc4/0xc4
[<ffffffff8242f5b8>] ubsan_epilogue+0xd/0x8a
[<ffffffff82430c41>] __ubsan_handle_shift_out_of_bounds+0x255/0x29a
[<ffffffff824309ec>] ? __ubsan_handle_out_of_bounds+0x180/0x180
[<ffffffff84003436>] ? nl80211_req_set_reg+0x256/0x2f0
[<ffffffff812112ba>] ? print_context_stack+0x8a/0x160
[<ffffffff81200031>] ? amd_pmu_reset+0x341/0x380
[<ffffffff823af808>] rht_deferred_worker+0x1618/0x1790
[<ffffffff823af808>] ? rht_deferred_worker+0x1618/0x1790
[<ffffffff823ae1f0>] ? rhashtable_jhash2+0x370/0x370
[<ffffffff8134c12d>] ? process_one_work+0x6fd/0x1970
[<ffffffff8134c1cf>] process_one_work+0x79f/0x1970
[<ffffffff8134c12d>] ? process_one_work+0x6fd/0x1970
[<ffffffff8134ba30>] ? try_to_grab_pending+0x4c0/0x4c0
[<ffffffff8134d564>] ? worker_thread+0x1c4/0x1340
[<ffffffff8134d8ff>] worker_thread+0x55f/0x1340
[<ffffffff845e904f>] ? __schedule+0x4df/0x1d40
[<ffffffff8134d3a0>] ? process_one_work+0x1970/0x1970
[<ffffffff8134d3a0>] ? process_one_work+0x1970/0x1970
[<ffffffff813642f7>] kthread+0x237/0x390
[<ffffffff813640c0>] ? __kthread_parkme+0x280/0x280
[<ffffffff845f8c93>] ? _raw_spin_unlock_irq+0x33/0x50
[<ffffffff845f95df>] ret_from_fork+0x1f/0x40
[<ffffffff813640c0>] ? __kthread_parkme+0x280/0x280
================================================================================
roundup_pow_of_two() is undefined when called with an argument of 0, so
let's avoid the call and just fall back to ht->p.min_size (which should
never be smaller than HASH_MIN_SIZE).
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because perf data from pipe do not have a header with evsel attr, we
should not check that and disable symbol_conf.use_callchain. Otherwise,
perf script won't show callchains even if the data stream contains
callchain.
Before:
$ perf record -g -o - uname |perf script
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
uname 1828 182630.186578: 250000 cpu-clock: ..b9499 setup_arg_pages
uname 1828 182630.186850: 250000 cpu-clock: ..83b20 ___might_sleep
uname 1828 182630.187153: 250000 cpu-clock: ..4b6be file_map_prot_ch
...
After:
$ perf record -g -o - uname |perf script
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
uname 1833 182675.927099: 250000 cpu-clock:
ba5520 _raw_spin_lock+0xfe200040 ([kernel.kallsyms])
389dd4 expand_downwards+0xfe200154 ([kernel.kallsyms])
389f34 expand_stack+0xfe200024 ([kernel.kallsyms])
3b957e setup_arg_pages+0xfe20019e ([kernel.kallsyms])
40c80f load_elf_binary+0xfe20042f ([kernel.kallsyms])
...
Signed-off-by: He Kuang <hekuang@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1470309943-153909-2-git-send-email-hekuang@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Perf shows the usage message when perf scripts folder failed to open,
which misleads users to let them think the command is being mistyped.
This patch shows a proper message and guides users to check the
PERF_EXEC_PATH environment variable in that case.
Before:
$ perf script --list
Usage: perf script [<options>]
or: perf script [<options>] record <script> [<record-options>] <command>
or: perf script [<options>] report <script> [script-args]
or: perf script [<options>] <script> [<record-options>] <command>
or: perf script [<options>] <top-script> [script-args]
-l, --list list available scripts
After:
$ perf script --list
open(/home/user/perf-core/scripts) failed.
Check for "PERF_EXEC_PATH" env to set scripts dir.
Signed-off-by: He Kuang <hekuang@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1470309943-153909-1-git-send-email-hekuang@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The called of_graph_get_next_endpoint() already decrements the refcount
of the prev node, so it is wrong to do it again in the calling function.
Use the for_each_endpoint_of_node() helper to interate through the
endpoint OF nodes, which already does the right thing and simplifies
the code a bit.
Fixes: 8ccd0d0ca041
(of: add helper for getting endpoint node of specific identifiers)
Cc: stable@vger.kernel.org
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Noticed on Fedora Rawhide:
$ gcc --version
gcc (GCC) 6.1.1 20160721 (Red Hat 6.1.1-4)
$ rpm -q glibc
glibc-2.24.90-1.fc26.x86_64
$
CC /tmp/build/perf/util/jitdump.o
util/jitdump.c: In function 'jit_repipe_code_load':
util/jitdump.c:428:2: error: '__major_from_sys_types' is deprecated:
In the GNU C Library, `major' is defined by <sys/sysmacros.h>.
For historical compatibility, it is currently defined by
<sys/types.h> as well, but we plan to remove this soon.
To use `major', include <sys/sysmacros.h> directly.
If you did not intend to use a system-defined macro `major',
you should #undef it after including <sys/types.h>.
[-Werror=deprecated-declarations]
event->mmap2.maj = major(st.st_dev);
^~~~~
In file included from /usr/include/features.h:397:0,
from /usr/include/sys/types.h:25,
from util/jitdump.c:1:
/usr/include/sys/sysmacros.h:87:1: note: declared here
__SYSMACROS_DEFINE_MAJOR (__SYSMACROS_FST_IMPL_TEMPL)
Fix it following that recomendation.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-3majvd0adhfr25rvx4v5e9te@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb().
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allwinner A64 EHCI requires 4 clocks to be enabled.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently bcma-hcd driver handles 3 different bcma cores:
1) BCMA_CORE_USB20_HOST (0x819)
2) BCMA_CORE_NS_USB20 (0x504)
3) BCMA_CORE_NS_USB30 (0x505)
The first one was introduced years ago and so far was used on MIPS
devices only. All Northstar (ARM) devices were using other two cores
which allowed easy implementation of separated initialization paths.
It seems however Broadcom decided to reuse this old USB 2.0 controller
on some recently introduced cheaper Northstar BCM53573 SoCs. I noticed
this on Tenda AC9 (based on BCM47189B0 belonging to BCM53573 family).
There is no difference in this old controller core identification
between MIPS and ARM devices: they share the same id and revision. We
need different controller initialization procedure however.
To handle this add a check for architecture and implement required
initialization for ARM case.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of error, the function platform_device_register_simple() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
The workqueue "workqueue" has multiple workitems which may require
ordering. Hence, a dedicated ordered workqueue has been used.
Since the workqueue is not being used on a memory reclaim path,
WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dynamic debugging will already add the function (and the line number)
to a debug message if one requests that. It makes no sense to add
them unconditionally in a driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
