| Age | Commit message (Collapse) | Author |
|---|
|
Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.
Fixes: 7a13240e3718 ("bnxt_en: fix ethtool_reset_flags ABI violations")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We must specify the vnic id of the vnic in the input structure of this
firmware message. Otherwise we will get an error from the firmware.
Fixes: 98a4322b70e8 ("bnxt_en: update RSS config using difference algorithm")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The previous commit fixed a verifier bypass by ensuring that ID is not
preserved on narrowing spills. Add the test cases to check the
problematic patterns.
Signed-off-by: Maxim Mikityanskiy <maxim@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230607123951.558971-3-maxtram95@gmail.com
|
|
The following scenario describes a bug in the verifier where it
incorrectly concludes about equivalent scalar IDs which could lead to
verifier bypass in privileged mode:
1. Prepare a 32-bit rogue number.
2. Put the rogue number into the upper half of a 64-bit register, and
roll a random (unknown to the verifier) bit in the lower half. The
rest of the bits should be zero (although variations are possible).
3. Assign an ID to the register by MOVing it to another arbitrary
register.
4. Perform a 32-bit spill of the register, then perform a 32-bit fill to
another register. Due to a bug in the verifier, the ID will be
preserved, although the new register will contain only the lower 32
bits, i.e. all zeros except one random bit.
At this point there are two registers with different values but the same
ID, which means the integrity of the verifier state has been corrupted.
5. Compare the new 32-bit register with 0. In the branch where it's
equal to 0, the verifier will believe that the original 64-bit
register is also 0, because it has the same ID, but its actual value
still contains the rogue number in the upper half.
Some optimizations of the verifier prevent the actual bypass, so
extra care is needed: the comparison must be between two registers,
and both branches must be reachable (this is why one random bit is
needed). Both branches are still suitable for the bypass.
6. Right shift the original register by 32 bits to pop the rogue number.
7. Use the rogue number as an offset with any pointer. The verifier will
believe that the offset is 0, while in reality it's the given number.
The fix is similar to the 32-bit BPF_MOV handling in check_alu_op for
SCALAR_VALUE. If the spill is narrowing the actual register value, don't
keep the ID, make sure it's reset to 0.
Fixes: 354e8f1970f8 ("bpf: Support <8-byte scalar spill and refill")
Signed-off-by: Maxim Mikityanskiy <maxim@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Andrii Nakryiko <andrii@kernel.org> # Checked veristat delta
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230607123951.558971-2-maxtram95@gmail.com
|
|
Selecting only REGMAP_I2C can leave REGMAP unset, causing build errors,
so also select REGMAP to prevent the build errors.
../drivers/misc/eeprom/at24.c:540:42: warning: 'struct regmap_config' declared inside parameter list will not be visible outside of this definition or declaration
540 | struct regmap_config *regmap_config)
../drivers/misc/eeprom/at24.c: In function 'at24_make_dummy_client':
../drivers/misc/eeprom/at24.c:552:18: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c:552:16: warning: assignment to 'struct regmap *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c: In function 'at24_probe':
../drivers/misc/eeprom/at24.c:586:16: error: variable 'regmap_config' has initializer but incomplete type
586 | struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: error: storage size of 'regmap_config' isn't known
586 | struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: warning: unused variable 'regmap_config' [-Wunused-variable]
Fixes: 5c015258478e ("eeprom: at24: add basic regmap_i2c support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:
== Thread A == == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
...
== Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
->__send_flush_snap()
handle_cap_flushsnap_ack()
->iput('&ci->vfs_inode')
this also will release 'ci'
...
== Thread D ==
ceph_handle_snap()
->flush_snaps()
->iterate 'mdsc->snap_flush_list'
->get the stale 'ci'
->remove 'ci' from ->ihold(&ci->vfs_inode) this
'mdsc->snap_flush_list' will WARNING
To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.
[ idryomov: need_put int -> bool ]
Cc: stable@vger.kernel.org
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2209299
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Milind Changire <mchangir@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Wait for AON bit in HOST_SS_CPR_RST_CLR to return 0 before
starting VPUIP power up sequence, otherwise the VPU device
may sporadically fail to boot.
An error in power up sequence is propagated to the runtime
power management - the device will be in an error state
until the VPU driver is reloaded.
Fixes: 35b137630f08 ("accel/ivpu: Introduce a new DRM driver for Intel VPU")
Cc: stable@vger.kernel.org # 6.3.x
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230607094502.388489-1-stanislaw.gruszka@linux.intel.com
|
|
If we get signal when waiting for the mmu->lock we do not invalidate
current MMU configuration that might result in undefined behavior.
Additionally there is little or no benefit on break waiting for
ipc->lock. In current code base, we keep this lock for short periods.
Fixes: 263b2ba5fc93 ("accel/ivpu: Add Intel VPU MMU support")
Reviewed-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230525103818.877590-2-stanislaw.gruszka@linux.intel.com
|
|
Turning off the PLL and entering D0i3 will reset the VPU so
an explicit IP reset is redundant.
But if the VPU is active, it may interfere with PLL disabling
and to avoid that, we have to issue an additional IP reset
to silence the VPU before turning off the PLL.
Fixes: a8fed6d1e0b9 ("accel/ivpu: Fix power down sequence")
Cc: stable@vger.kernel.org # 6.3.x
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230525103818.877590-1-stanislaw.gruszka@linux.intel.com
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here is a batman-adv bugfix:
- fix a broken sync while rescheduling delayed work,
by Vladislav Efanov
* tag 'batadv-net-pullrequest-20230607' of git://git.open-mesh.org/linux-merge:
batman-adv: Broken sync while rescheduling delayed work
====================
Link: https://lore.kernel.org/r/20230607155515.548120-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We had a number of short comings:
- EEE must be re-evaluated whenever the state machine detects a link
change as wight be switching from a link partner with EEE
enabled/disabled
- tx_lpi_enabled controls whether EEE should be enabled/disabled for the
transmit path, which applies to the TBUF block
- We do not need to forcibly enable EEE upon system resume, as the PHY
state machine will trigger a link event that will do that, too
Fixes: 6ef398ea60d9 ("net: bcmgenet: add EEE support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230606214348.2408018-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Flip the netif_carrier_ok() condition in queue wake logic.
When I moved it to inside __netif_txq_completed_wake()
I missed negating it.
This made the condition ineffective and could probably
lead to crashes.
Fixes: 301f227fc860 ("net: piggy back on the memory barrier in bql when waking queues")
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230607010826.960226-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The down condition should be the negation of the wake condition,
IOW when I moved it from:
if (cond && wake())
to
if (__netif_txq_completed_wake(cond))
Cond should have been negated. Flip it now.
This bug leads to occasional crashes with netconsole.
It may also lead to queue never waking up in case BQL is not enabled.
Reported-by: David Wei <davidhwei@meta.com>
Fixes: 08a096780d92 ("bnxt: use new queue try_stop/try_wake macros")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230607010826.960226-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-06-07
We've added 7 non-merge commits during the last 7 day(s) which contain
a total of 12 files changed, 112 insertions(+), 7 deletions(-).
The main changes are:
1) Fix a use-after-free in BPF's task local storage, from KP Singh.
2) Make struct path handling more robust in bpf_d_path, from Jiri Olsa.
3) Fix a syzbot NULL-pointer dereference in sockmap, from Eric Dumazet.
4) UAPI fix for BPF_NETFILTER before final kernel ships,
from Florian Westphal.
5) Fix map-in-map array_map_gen_lookup code generation where elem_size was
not being set for inner maps, from Rhys Rustad-Elliott.
6) Fix sockopt_sk selftest's NETLINK_LIST_MEMBERSHIPS assertion,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add extra path pointer check to d_path helper
selftests/bpf: Fix sockopt_sk selftest
bpf: netfilter: Add BPF_NETFILTER bpf_attach_type
selftests/bpf: Add access_inner_map selftest
bpf: Fix elem_size not being set for inner maps
bpf: Fix UAF in task local storage
bpf, sockmap: Avoid potential NULL dereference in sk_psock_verdict_data_ready()
====================
Link: https://lore.kernel.org/r/20230607220514.29698-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
irq_cpu_rmap_release() calls cpu_rmap_put(), which may free the rmap.
So we need to clear the pointer to our glue structure in rmap before
doing that, not after.
Fixes: 4e0473f1060a ("lib: cpu_rmap: Avoid use after free on rmap->obj array entries")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/ZHo0vwquhOy3FaXc@decadent.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If caller reports ENOMEM, then stop iterating over the batch and send a
single netlink message to userspace to report OOM.
Fixes: cbb8125eb40b ("netfilter: nfnetlink: deliver netlink errors on batch completion")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The pipapo set backend follows copy-on-update approach, maintaining one
clone of the existing datastructure that is being updated. The clone
and current datastructures are swapped via rcu from the commit step.
The existing integration with the commit protocol is flawed because
there is no operation to clean up the clone if the transaction is
aborted. Moreover, the datastructure swap happens on set element
activation.
This patch adds two new operations for sets: commit and abort, these new
operations are invoked from the commit and abort steps, after the
transactions have been digested, and it updates the pipapo set backend
to use it.
This patch adds a new ->pending_update field to sets to maintain a list
of sets that require this new commit and abort operations.
Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
[Description]
Reduce expected SDP bandwidth due to poor QoS and
arbitration issues on high bandwidth configs
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The link object of mgr->reserved_pages is the blocks
variable in struct amdgpu_vram_reservation, not the
link variable in struct drm_buddy_block.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
According to Alex, most APUs from that time seem to have the same issue
(vbios says 48Mhz, actual is 100Mhz). I only have a CHIP_STONEY so I
limit the fixup to CHIP_STONEY
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Userspace can race to free the gobj(robj converted from), robj should not
be accessed again after drm_gem_object_put, otherwith it will result in
use-after-free.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit f03eb1d26c2739b75580f58bbab4ab2d5d3eba46.
This results in inconsistent timing reported via asynchronous
GPU queries.
Link: https://lists.freedesktop.org/archives/amd-gfx/2023-May/093731.html
Cc: Jesse.Zhang@amd.com
Cc: michel@daenzer.net
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
to revision id"
This reverts commit 9d2d1827af295fd6971786672c41c4dba3657154.
This results in inconsistent timing reported via asynchronous
GPU queries.
Link: https://lists.freedesktop.org/archives/amd-gfx/2023-May/093731.html
Cc: Jesse.Zhang@amd.com
Cc: michel@daenzer.net
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit fbc24293ca16b3b9ef891fe32ccd04735a6f8dc1.
This results in inconsistent timing reported via asynchronous
GPU queries.
Link: https://lists.freedesktop.org/archives/amd-gfx/2023-May/093731.html
Cc: Jesse.Zhang@amd.com
Cc: michel@daenzer.net
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When going from ODM 2:1 single display case to max displays, second
odm pipe needs to be repurposed for one of the new single displays.
However, acquire_first_split_pipe() only handles MPC case and not
ODM case
[How]
Add ODM conditions in acquire_first_split_pipe()
Add commit_minimal_transition_state() in commit_streams() to handle
odm 2:1 exit first, and then process new streams
Handle ODM condition in commit_minimal_transition_state()
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
during suspend path
Users have reported that s2idle wasn't working on OEM Phoenix systems,
but it was root caused to be because `CONFIG_AMD_PMC` wasn't set in
the distribution kernel config.
To make this more apparent, raise the messaging to err instead of warn.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217497
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
sienna_cichlid SKUs
Disable the pcie lane switching for some sienna_cichlid SKUs since it
might not work well on some platforms.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Use the right data structure for allocation.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Use the function of amdgpu_bo_vm_destroy to handle the resource release
of shadow bo. During the amdgpu_mes_self_test, shadow bo released, but
vmbo->shadow_list was not, which caused a null pointer reference error
in amdgpu_device_recover_vram when GPU reset.
Fixes: 6c032c37ac3e ("drm/amdgpu: Fix vram recover doesn't work after whole GPU reset (v2)")
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
commit cf488dcd0ab7 ("drm/amd: Allow s0ix without BIOS support") showed
improvements to power consumption over suspend when s0ix wasn't enabled in
BIOS and the system didn't support S3.
This patch however was misguided because the reason the system didn't
support S3 was because SMT was disabled in OEM BIOS setup.
This prevented the BIOS from allowing S3.
Also allowing GPUs to use the s2idle path actually causes problems if
they're invoked on systems that may not support s2idle in the platform
firmware. `systemd` has a tendency to try to use `s2idle` if `deep` fails
for any reason, which could lead to unexpected flows.
The original commit also fixed a problem during resume from suspend to idle
without hardware support, but this is no longer necessary with commit
ca4751866397 ("drm/amd: Don't allow s0ix on APUs older than Raven")
Revert commit cf488dcd0ab7 ("drm/amd: Allow s0ix without BIOS support")
to make it match the expected behavior again.
Cc: Rafael Ávila de Espíndola <rafael@espindo.la>
Link: https://github.com/torvalds/linux/blob/v6.1/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c#L1060
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2599
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- a fix for unbalanced open count for inhibited input devices
- fixups in Elantech PS/2 and Cyppress TTSP v5 drivers
- a quirk to soc_button_array driver to make it work with Lenovo
Yoga Book X90F / X90L
- a removal of erroneous entry from xpad driver
* tag 'input-for-v6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - delete a Razer DeathAdder mouse VID/PID entry
Input: psmouse - fix OOB access in Elantech protocol
Input: soc_button_array - add invalid acpi_index DMI quirk handling
Input: fix open count when closing inhibited device
Input: cyttsp5 - fix array length
|
|
In commit 95433f726301 ("srcu: Begin offloading srcu_struct fields to
srcu_update"), a new struct srcu_usage field was added, but was not
properly initialized. This led to a "spinlock bad magic" BUG when the
SRCU notifier was ever used. This was observed in the MediaTek CCI
devfreq driver on next-20230525. The trimmed stack trace is as follows:
BUG: spinlock bad magic on CPU#4, swapper/0/1
lock: 0xffffff80ff529ac0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Call trace:
spin_bug+0xa4/0xe8
do_raw_spin_lock+0xec/0x120
_raw_spin_lock_irqsave+0x78/0xb8
synchronize_srcu+0x3c/0x168
srcu_notifier_chain_unregister+0x5c/0xa0
cpufreq_unregister_notifier+0x94/0xe0
devfreq_passive_event_handler+0x7c/0x3e0
devfreq_remove_device+0x48/0xe8
Add __SRCU_USAGE_INIT() to SRCU_NOTIFIER_INIT() so that srcu_usage gets
initialized properly.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 95433f726301 ("srcu: Begin offloading srcu_struct fields to srcu_update")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Cc: Sachin Sant <sachinp@linux.ibm.com>
Cc: Joel Fernandes (Google) <joel@joelfernandes.org
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Zqiang <qiang.zhang1211@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
Use kzalloc() to allocate new zeroed out msg node instead of
memsetting a node allocated with kmalloc().
Signed-off-by: Prathu Baronia <prathubaronia2011@gmail.com>
Message-Id: <20230522085019.42914-1-prathubaronia2011@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
|
|
This is overdue and an oversight.
Add myself to this file deespite the fact that I'm trying to reduce the
number of entries in this file which have my name attached, but in the
hope that patches wont get picked up elsewhere completely unreviewed and
unnoticed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The description says 'RTL8723CS/RTL8723CS/...' whereas the title and
other places reference 'RTL8723BS/RTL8723CS/...'.
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230509141500.275887-1-didi.debian@cknow.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Update the fallback string for the RTL8821CS from realtek,rtl8822cs-bt
to realtek,rtl8723bs-bt. The difference between these two strings is
that the 8822cs enables power saving features that the 8723bs does not,
and in testing the 8821cs seems to have issues with these power saving
modes enabled.
Fixes: 95ee3a93239e ("dt-bindings: net: realtek-bluetooth: Add RTL8821CS")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230508160811.3568213-2-macroalpha82@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
kafs incorrectly passes a zero mtime (ie. 1st Jan 1970) to the server when
creating a file, dir or symlink because the mtime recorded in the
afs_operation struct gets passed to the server by the marshalling routines,
but the afs_mkdir(), afs_create() and afs_symlink() functions don't set it.
This gets masked if a file or directory is subsequently modified.
Fix this by filling in op->mtime before calling the create op.
Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sebastian reports that commit 1c913a1c35aa ("KVM: arm64: Iterate
arm_pmus list to probe for default PMU") introduced the following splat
with CONFIG_DEBUG_PREEMPT enabled:
[70506.110187] BUG: using smp_processor_id() in preemptible [00000000] code: qemu-system-aar/3078242
[70506.119077] caller is debug_smp_processor_id+0x20/0x30
[70506.124229] CPU: 129 PID: 3078242 Comm: qemu-system-aar Tainted: G W 6.4.0-rc5 #25
[70506.133176] Hardware name: GIGABYTE R181-T92-00/MT91-FS4-00, BIOS F34 08/13/2020
[70506.140559] Call trace:
[70506.142993] dump_backtrace+0xa4/0x130
[70506.146737] show_stack+0x20/0x38
[70506.150040] dump_stack_lvl+0x48/0x60
[70506.153704] dump_stack+0x18/0x28
[70506.157007] check_preemption_disabled+0xe4/0x108
[70506.161701] debug_smp_processor_id+0x20/0x30
[70506.166046] kvm_arm_pmu_v3_set_attr+0x460/0x628
[70506.170662] kvm_arm_vcpu_arch_set_attr+0x88/0xd8
[70506.175363] kvm_arch_vcpu_ioctl+0x258/0x4a8
[70506.179632] kvm_vcpu_ioctl+0x32c/0x6b8
[70506.183465] __arm64_sys_ioctl+0xb4/0x100
[70506.187467] invoke_syscall+0x78/0x108
[70506.191205] el0_svc_common.constprop.0+0x4c/0x100
[70506.195984] do_el0_svc+0x34/0x50
[70506.199287] el0_svc+0x34/0x108
[70506.202416] el0t_64_sync_handler+0xf4/0x120
[70506.206674] el0t_64_sync+0x194/0x198
Fix the issue by using the raw variant that bypasses the debug
assertion. While at it, stick all of the nuance and UAPI baggage into a
comment for posterity.
Fixes: 1c913a1c35aa ("KVM: arm64: Iterate arm_pmus list to probe for default PMU")
Reported-by: Sebastian Ott <sebott@redhat.com>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230606184814.456743-1-oliver.upton@linux.dev
|
|
When reworking the vgic locking, the vgic distributor registration
got simplified, which was a very good cleanup. But just a tad too
radical, as we now register the *native* vgic only, ignoring the
GICv2-on-GICv3 that allows pre-historic VMs (or so I thought)
to run.
As it turns out, QEMU still defaults to GICv2 in some cases, and
this breaks Nathan's setup!
Fix it by propagating the *requested* vgic type rather than the
host's version.
Fixes: 59112e9c390b ("KVM: arm64: vgic: Fix a circular locking issue")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
link: https://lore.kernel.org/r/20230606221525.GA2269598@dev-arch.thelio-3990X
|
|
We used to only check the alignment of the physical address to decide
which mapping would fit for a certain region of the linear mapping, but
it is not enough since the virtual address must also be aligned, so check
that too.
Fixes: 3335068f8721 ("riscv: Use PUD/P4D/PGD pages for the linear mapping")
Reported-by: Song Shuai <songshuaishuai@tinylab.org>
Link: https://lore.kernel.org/linux-riscv/tencent_7C3B580B47C1B17C16488EC1@qq.com/
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230607125851.63370-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
RISC-V Kfence implementation used to rely on the fact the linear mapping
was backed by at most PMD hugepages, which is not true anymore since
commit 3335068f8721 ("riscv: Use PUD/P4D/PGD pages for the linear
mapping").
Instead of splitting PUD/P4D/PGD mappings afterwards, directly map the
kfence pool region using PTE mappings by allocating this region before
setup_vm_final().
Reported-by: syzbot+a74d57bddabbedd75135@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a74d57bddabbedd75135
Fixes: 3335068f8721 ("riscv: Use PUD/P4D/PGD pages for the linear mapping")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230606130444.25090-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Commit 8aeb7b17f04e ("RISC-V: Make mmap() with PROT_WRITE imply PROT_READ")
allows riscv to use mmap with PROT_WRITE only, and meanwhile mmap with w+x
is also permitted. However, when userspace tries to access this page with
PROT_WRITE|PROT_EXEC, which causes infinite loop at load page fault as
well as it triggers soft lockup. According to riscv privileged spec,
"Writable pages must also be marked readable". The fix to drop the
`PAGE_COPY_READ_EXEC` and then `PAGE_COPY_EXEC` would be just used instead.
This aligns the other arches (i.e arm64) for protection_map.
Fixes: 8aeb7b17f04e ("RISC-V: Make mmap() with PROT_WRITE imply PROT_READ")
Signed-off-by: Hsieh-Tseng Shen <woodrow.shen@sifive.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230425102828.1616812-1-woodrow.shen@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The PM8550 uses only NLDOs 515 and the LDO 6 through 8 are low voltage
type, so fix accordingly.
Fixes: e6e3776d682d ("regulator: qcom-rpmh: Add support for PM8550 regulators")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230605115607.921308-1-abel.vesa@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Anastasios reported crash on stable 5.15 kernel with following
BPF attached to lsm hook:
SEC("lsm.s/bprm_creds_for_exec")
int BPF_PROG(bprm_creds_for_exec, struct linux_binprm *bprm)
{
struct path *path = &bprm->executable->f_path;
char p[128] = { 0 };
bpf_d_path(path, p, 128);
return 0;
}
But bprm->executable can be NULL, so bpf_d_path call will crash:
BUG: kernel NULL pointer dereference, address: 0000000000000018
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC NOPTI
...
RIP: 0010:d_path+0x22/0x280
...
Call Trace:
<TASK>
bpf_d_path+0x21/0x60
bpf_prog_db9cf176e84498d9_bprm_creds_for_exec+0x94/0x99
bpf_trampoline_6442506293_0+0x55/0x1000
bpf_lsm_bprm_creds_for_exec+0x5/0x10
security_bprm_creds_for_exec+0x29/0x40
bprm_execve+0x1c1/0x900
do_execveat_common.isra.0+0x1af/0x260
__x64_sys_execve+0x32/0x40
It's problem for all stable trees with bpf_d_path helper, which was
added in 5.9.
This issue is fixed in current bpf code, where we identify and mark
trusted pointers, so the above code would fail even to load.
For the sake of the stable trees and to workaround potentially broken
verifier in the future, adding the code that reads the path object from
the passed pointer and verifies it's valid in kernel space.
Fixes: 6e22ab9da793 ("bpf: Add d_path helper")
Reported-by: Anastasios Papagiannis <tasos.papagiannnis@gmail.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230606181714.532998-1-jolsa@kernel.org
|
|
Andy has been a de-facto reviewer for all things GPIO for a long time so
let's make it official.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The user-space policy of the gpio-sim is that configuration for lines
with offsets outside the bounds of the corresponding bank is ignored,
but gpio-sim is still using that configuration when constructing the
sim. In the case of named lines this results in temporarily allocating
space for names that are not used, and for hogs results in errors being
logged when the gpio-sim attempts to register the out of range hog with
gpiolib:
gpiochip_machine_hog: unable to get GPIO desc: -22
Add checks to filter out any line configuration outside the bounds
of the bank when constructing the sim.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
try_module_get will be called in tcf_proto_lookup_ops. So module_put needs
to be called to drop the refcount if ops don't implement the required
function.
Fixes: 9f407f1768d3 ("net: sched: introduce chain templates")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes following sparse errors:
net/sched/act_police.c:360:28: warning: dereference of noderef expression
net/sched/act_police.c:362:45: warning: dereference of noderef expression
net/sched/act_police.c:362:45: warning: dereference of noderef expression
net/sched/act_police.c:368:28: warning: dereference of noderef expression
net/sched/act_police.c:370:45: warning: dereference of noderef expression
net/sched/act_police.c:370:45: warning: dereference of noderef expression
net/sched/act_police.c:376:45: warning: dereference of noderef expression
net/sched/act_police.c:376:45: warning: dereference of noderef expression
Fixes: d1967e495a8d ("net_sched: act_police: add 2 new attributes to support police 64bit rate and peakrate")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the per cpu upcall counters are allocated after the vport is
created and inserted into the system. This could lead to the datapath
accessing the counters before they are allocated resulting in a kernel
Oops.
Here is an example:
PID: 59693 TASK: ffff0005f4f51500 CPU: 0 COMMAND: "ovs-vswitchd"
#0 [ffff80000a39b5b0] __switch_to at ffffb70f0629f2f4
#1 [ffff80000a39b5d0] __schedule at ffffb70f0629f5cc
#2 [ffff80000a39b650] preempt_schedule_common at ffffb70f0629fa60
#3 [ffff80000a39b670] dynamic_might_resched at ffffb70f0629fb58
#4 [ffff80000a39b680] mutex_lock_killable at ffffb70f062a1388
#5 [ffff80000a39b6a0] pcpu_alloc at ffffb70f0594460c
#6 [ffff80000a39b750] __alloc_percpu_gfp at ffffb70f05944e68
#7 [ffff80000a39b760] ovs_vport_cmd_new at ffffb70ee6961b90 [openvswitch]
...
PID: 58682 TASK: ffff0005b2f0bf00 CPU: 0 COMMAND: "kworker/0:3"
#0 [ffff80000a5d2f40] machine_kexec at ffffb70f056a0758
#1 [ffff80000a5d2f70] __crash_kexec at ffffb70f057e2994
#2 [ffff80000a5d3100] crash_kexec at ffffb70f057e2ad8
#3 [ffff80000a5d3120] die at ffffb70f0628234c
#4 [ffff80000a5d31e0] die_kernel_fault at ffffb70f062828a8
#5 [ffff80000a5d3210] __do_kernel_fault at ffffb70f056a31f4
#6 [ffff80000a5d3240] do_bad_area at ffffb70f056a32a4
#7 [ffff80000a5d3260] do_translation_fault at ffffb70f062a9710
#8 [ffff80000a5d3270] do_mem_abort at ffffb70f056a2f74
#9 [ffff80000a5d32a0] el1_abort at ffffb70f06297dac
#10 [ffff80000a5d32d0] el1h_64_sync_handler at ffffb70f06299b24
#11 [ffff80000a5d3410] el1h_64_sync at ffffb70f056812dc
#12 [ffff80000a5d3430] ovs_dp_upcall at ffffb70ee6963c84 [openvswitch]
#13 [ffff80000a5d3470] ovs_dp_process_packet at ffffb70ee6963fdc [openvswitch]
#14 [ffff80000a5d34f0] ovs_vport_receive at ffffb70ee6972c78 [openvswitch]
#15 [ffff80000a5d36f0] netdev_port_receive at ffffb70ee6973948 [openvswitch]
#16 [ffff80000a5d3720] netdev_frame_hook at ffffb70ee6973a28 [openvswitch]
#17 [ffff80000a5d3730] __netif_receive_skb_core.constprop.0 at ffffb70f06079f90
We moved the per cpu upcall counter allocation to the existing vport
alloc and free functions to solve this.
Fixes: 95637d91fefd ("net: openvswitch: release vport resources on failure")
Fixes: 1933ea365aa7 ("net: openvswitch: Add support to count upcall packets")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtm_tca_policy is used from net/sched/sch_api.c and net/sched/cls_api.c,
thus should be declared in an include file.
This fixes the following sparse warning:
net/sched/sch_api.c:1434:25: warning: symbol 'rtm_tca_policy' was not declared. Should it be static?
Fixes: e331473fee3d ("net/sched: cls_api: add missing validation of netlink attributes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
