| Age | Commit message (Collapse) | Author |
|---|
|
This patch removes un-needed spin_lock in stmmac_ioctl while reading and
writing mdio registers. While holding spin_lock the code must be
atomic, which is not true in this case as both mdiobus_read and writes
have mutex locks.
Without this patch reading mdio registers via mii-tool results in below
BUG:
mii-tool -vvv eth0"
Using SIOCGMIIPHY=0x8947
BUG: sleeping function called from invalid context at kernel/mutex.c:287
in_atomic(): 1, irqs_disabled(): 0, pid: 614, name: mii-tool
2 locks held by mii-tool/614:
#0: (rtnl_mutex){......}, at: [<c01fd80c>] dev_ioctl+0x550/0x674
#1: (&priv->lock){......}, at: [<c01b34ec>] stmmac_ioctl+0x4c/0x78
[<c002ea14>] (unwind_backtrace+0x0/0xcc) from [<c0272c38>]
(mutex_lock_nested+0x24/0x35c)
[<c0272c38>] (mutex_lock_nested+0x24/0x35c) from [<c01b237c>]
(mdiobus_read+0x44/0x70)
[<c01b237c>] (mdiobus_read+0x44/0x70) from [<c01b0c64>]
(phy_mii_ioctl+0x4c/0x138)
[<c01b0c64>] (phy_mii_ioctl+0x4c/0x138) from [<c01b34fc>]
(stmmac_ioctl+0x5c/0x78)
[<c01b34fc>] (stmmac_ioctl+0x5c/0x78) from [<c01fcec8>]
(dev_ifsioc+0x2a4/0x2c8)
[<c01fcec8>] (dev_ifsioc+0x2a4/0x2c8) from [<c01fd81c>]
(dev_ioctl+0x560/0x674)
[<c01fd81c>] (dev_ioctl+0x560/0x674) from [<c00c36e0>]
(vfs_ioctl+0x2c/0x8c)
[<c00c36e0>] (vfs_ioctl+0x2c/0x8c) from [<c00c4130>]
(do_vfs_ioctl+0x530/0x578)
[<c00c4130>] (do_vfs_ioctl+0x530/0x578) from [<c00c41ac>]
(sys_ioctl+0x34/0x54)
[<c00c41ac>] (sys_ioctl+0x34/0x54) from [<c0028aa0>]
(ret_fast_syscall+0x0/0x2c)
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New GMAC devices (newer than the databook 3.50a) have the
HW capability register that provides which features are actually
supported by the hardware.
On old devices many information have to be passed through the
platform, for example: enhanced descriptor structure,
TX COE etc. These are mandatory to properly configure the driver.
This remains still valid because the driver has to support old
Synopsys devices but now it's also able to override them using the
values from the HW capability register if supported.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the way to stop the 1000Base advertising
capabilties for non GMII interfaces.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses an mdelay to manage the timeout on
sw reset to be independant of cpu_clk.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On PPC64, put_sigset_t converts a sigset_t to a compat_sigset_t
before copying it to userspace. There is a typo in the case that
we have 4 words to copy, meaning that we corrupt the compat_sigset_t.
It appears that _NSIG_WORDS can't be greater than 2 at the moment
so this code is probably always optimised away anyway.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The Documentation/memory-barriers.txt document requires that atomic
operations that return a value act as a memory barrier both before
and after the actual atomic operation.
Our current implementation doesn't guarantee this. More specifically,
while a load following the isync can not be issued before stwcx. has
completed, that completion doesn't architecturally means that the
result of stwcx. is visible to other processors (or any previous stores
for that matter) (typically, the other processors L1 caches can still
hold the old value).
This has caused an actual crash in RCU torture testing on Power 7
This fixes it by changing those atomic ops to use new macros instead
of RELEASE/ACQUIRE barriers, called ATOMIC_ENTRY and ATMOIC_EXIT barriers,
which are then defined respectively to lwsync and sync.
I haven't had a chance to measure the performance impact (or rather
what I measured with kernel compiles is in the noise, I yet have to
find a more precise benchmark)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Recent binutils refuses to assemble AltiVec opcodes when in e500/SPE
mode, as some of those opcodes alias the "SPE" instructions. This
triggers an ancient binutils version check even when building a kernel
with CONFIG_ALTIVEC disabled.
In theory, the check could be conditionalized on CONFIG_ALTIVEC, but in
practice it has long outlived its utility. It is virtually impossible
to find binutils older than 2.12.1 (released 2002) in the wild anymore.
Even ancient RedHat Enterprise Linux 4 has binutils-2.14.
To fix the kernel build when done natively on e500 systems with this new
binutils, the test is simply removed.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With the introduction of CONFIG_PPC_ADV_DEBUG_REGS user space debug is
broken on Book-E 64-bit parts that support delayed debug events. When
switch_booke_debug_regs() sets DBCR0 we'll start getting debug events as
MSR_DE is also set and we aren't able to handle debug events from kernel
space.
We can remove the hack that always enables MSR_DE and loads up DBCR0 and
just utilize switch_booke_debug_regs() to get user space debug working
again.
We still need to handle critical/debug exception stacks & proper
save/restore of state for those exception levles to support debug events
from kernel space like we have on 32-bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
All of DebugException is already protected by CONFIG_PPC_ADV_DEBUG_REGS
there is no need to have another such ifdef inside the function.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We had an existing ifdef for 4xx & BOOKE processors that got changed to
CONFIG_PPC_ADV_DEBUG_REGS. The define has nothing to do with
CONFIG_PPC_ADV_DEBUG_REGS. The define really should be:
#if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
and not
#ifdef CONFIG_PPC_ADV_DEBUG_REGS
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The BIOS VBT value for an eDP panel has been shown to be incorrect on
one machine, and we haven't found any machines where the DPCD value
was wrong, so we'll use the DPCD value everywhere.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Limit the link training setting command to the lanes needed for the
current mode. It seems vaguely possible that a monitor will try to
train the other lanes and fail in some way, so this seems like the
safer plan.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Found a couple of bare tabs in intel_dp.c
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Instead of going through the sequence just once, run through the whole
set up to 5 times to see if something can work. This isn't part of the
DP spec, but the BIOS seems to do it, and given that link training
failure is so bad, it seems reasonable to follow suit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Make sure the sequence of operations in all three functions makes
sense:
1) The backlight must be off unless the screen is running
2) The link must be running to turn the eDP panel on/off
3) The CPU eDP PLL must be running until everything is off
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
The panel power sequencing hardware tracks the stages of panel power
sequencing and signals when the panel is completely on or off. Instead
of blindly assuming the panel timings will work, poll the panel power
status register until it shows the correct values.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
PCH eDP has many of the same needs as regular PCH DP connections,
including the DP_CTl bit settings, the TRANS_DP_CTL register.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
No persistent data was ever stored here, so link_status is instead
allocated on the stack as needed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Every usage of PCH_PP_CONTROL sets the PANEL_UNLOCK_REGS value to
ensure that writes will be respected, move this to a common function
to make the driver cleaner.
No functional changes.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
takes vfsmount and relative path, does lookup within that vfsmount
(possibly triggering automounts) and returns the result as root
of subtree suitable for return by ->mount() (i.e. a reference to
dentry and an active reference to its superblock grabbed, superblock
locked exclusive).
btrfs and nfs switched to it instead of open-coding the sucker.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Update version number.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than generating a different RSS key on each boot, just use
a predetermined value that will map same flow to same value on
every device.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default Tx ring size for the sky2 driver is quite large and could
cause excess buffer bloat for many users. The minimum ring size
possible and still allow handling the worst case packet on 64bit platforms
is 38 which gets rounded up to a power of 2. But most packets only require
a couple of ring elements.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code is clearer if the up/down functions are renamed to
open/close like other drivers. Purely syntax change.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A couple of the reset and setup paths have possible PCI posting issues.
When setting registers, a read is necessary to force the writes to complete.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several problems with recent change to how IRQ's are setup.
* synchronize_irq in sky2_shutdown would hang because there
was no IRQ setup.
* when device was set to down, some IRQ bits left enabled so a
hardware error would produce IRQ with no handler
* quick link on Optima chip set was enabled without handler
* suspend/resume would leave IRQ on with no handler if device
was down
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are checking whether the MCR0_HASHEN bit is set using a logical and
instead of bitwise and, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there is an architecture-specific random number generator we use
it to acquire randomness one "long" at a time. We should put these
random words into consecutive words in the result buffer - not just
overwrite the first word again and again.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4ec4061010261a4cb0@agluck-desktop.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
My old email account at linux-foundation is no longer usable after
the LF breakin.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first #include must be pch_gbe.h as it
does a #define of pr_fmt.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-request fw from fs may fail for different reasons, once the fw was
loaded we won't release it until driver is removed.
This also resolves the boot problem when initial fw is located on initrd,
but rootfs is still unavailable, in this case device reset will fail due
to absence of fw files.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
so the defconfig of the atmel continue to have the support of the network
as before
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bridge multicast snooping of ICMPv6 would incorrectly report a checksum problem
when used with Ethernet devices like sky2 that use CHECKSUM_COMPLETE.
When bytes are removed from skb, the computed checksum needs to be adjusted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Martin Volf <martin.volf.42@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch avoids SIGA-r calls in case of SIGA-r required. It only calls
SIGA-r if a threshold of free buffer is reached. CPU consumption is
reduced as a consequence.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when use dst_get_neighbour to get neighbour, we need
rcu_read_lock to protect, since dst_get_neighbour uses
rcu_dereference.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Invocation of dev_alloc_name() is re-inserted, because the created
net_device name is used to create the device name for the iucv bus.
This device is created before the register_netdev call.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch "qeth: exploit asynchronous delivery of storage blocks"
added a WARN_ON in qeth_schedule_recovery. A device recovery should
not cause a kernel warning. This is obviously a debugging left-over
that we forgot to remove.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without appropriate configuration at the SE, a HiperSockets device
cannot be used for sniffing. Setting the sniffer attribute is rejected
with -EPERM.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Kirby reported divides by zero errors in __tcp_select_window()
This happens when inet_csk_route_child_sock() returns a NULL pointer :
We free new socket while we eventually armed keepalive timer in
tcp_create_openreq_child()
Fix this by a call to tcp_clear_xmit_timers()
[ This is a followup to commit 918eb39962dff (net: add missing
bh_unlock_sock() calls) ]
Reported-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Life is much saner if create_mnt_ns(mnt) drops mnt in case of error...
Switch it to such calling conventions, switch callers, fix double mntput() in
fs/nfs/super.c one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Looks like a typo creeped in, and driver prints
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq abled
instead of
s3c2410-wdt s3c2410-wdt: watchdog active, reset enabled, irq enabled
Also it may completely disinform about irq status, as it prints
"irq enabled" when S3C2410_WTCON_INTEN is in fact 0.
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Encrypted keys are encrypted/decrypted using either a trusted or
user-defined key type, which is referred to as the 'master' key.
The master key may be of type trusted iff the trusted key is
builtin or both the trusted key and encrypted keys are built as
modules. This patch resolves the build dependency problem.
- Use "masterkey-$(CONFIG_TRUSTED_KEYS)-$(CONFIG_ENCRYPTED_KEYS)" construct
to encapsulate the above logic. (Suggested by Dimtry Kasatkin.)
- Fixing the encrypted-keys Makefile, results in a module name change
from encrypted.ko to encrypted-keys.ko.
- Add module dependency for request_trusted_key() definition
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
|
|
Fix request_master_key() error return code.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
|
|
gref->gref_id is unsigned so the error handling didn't work.
gnttab_grant_foreign_access() returns an int type, so we can add a
cast here, and it doesn't cause any problems.
gnttab_grant_foreign_access() can return a variety of errors
including -ENOSPC, -ENOSYS and -ENOMEM.
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
On 32 bit systems a high value of op.count could lead to an integer
overflow in the kzalloc() and gref_ids would be smaller than
expected. If the you triggered another integer overflow in
"if (gref_size + op.count > limit)" then you'd probably get memory
corruption inside add_grefs().
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
The multiplications here can overflow resulting in smaller buffer
sizes than expected. "count" comes from a copy_from_user().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
PVHVM running with more than 32 vcpus and pv_irq/pv_time enabled
need VCPU placement to work, or else it will softlockup.
CC: stable@kernel.org
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
If highmem pages are requested from the balloon on a system without
highmem, the implementation of alloc_xenballooned_pages will allocate
all available memory trying to find highmem pages to return. Allow
low memory to be returned when highmem pages are requested to avoid
this loop.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
