| Age | Commit message (Collapse) | Author |
|---|
|
PHY_POLL is defined as -1 which means that we would be setting all flags of the
PHY driver, this is also not a valid flag to tell PHYLIB about, just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Davide Caratti says:
====================
net/sched: act_police: lockless data path
the data path of 'police' action can be faster if we avoid using spinlocks:
- patch 1 converts act_police to use per-cpu counters
- patch 2 lets act_police use RCU to access its configuration data.
test procedure (using pktgen from https://github.com/netoptimizer):
# ip link add name eth1 type dummy
# ip link set dev eth1 up
# tc qdisc add dev eth1 clsact
# tc filter add dev eth1 egress matchall action police \
> rate 2gbit burst 100k conform-exceed pass/pass index 100
# for c in 1 2 4; do
> ./pktgen_bench_xmit_mode_queue_xmit.sh -v -s 64 -t $c -n 5000000 -i eth1
> done
test results (avg. pps/thread):
$c | before patch | after patch | improvement
----+--------------+--------------+-------------
1 | 3518448 | 3591240 | irrelevant
2 | 3070065 | 3383393 | 10%
4 | 1540969 | 3238385 | 110%
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use RCU instead of spinlocks, to protect concurrent read/write on
act_police configuration. This reduces the effects of contention in the
data path, in case multiple readers are present.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use per-CPU counters, instead of sharing a single set of stats with all
cores. This removes the need of using spinlock when statistics are read
or updated.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
udp: add missing check on edumx rx path
The early demux RX path for the UDP protocol is currently missing
some checks. Both ipv4 and ipv6 implementations lack checksum conversion
and the ipv6 implementation additionally lack the zero checksum
validation.
The first patch takes care of UDPv4 and the second one of UDPv6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the UDPv6 early demux rx code path lacks some mandatory
checks, already implemented into the normal RX code path - namely
the checksum conversion and no_check6_rx check.
Similar to the previous commit, we move the common processing to
an UDPv6 specific helper and call it from both edemux code path
and normal code path. In respect to the UDPv4, we need to add an
explicit check for non zero csum according to no_check6_rx value.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Xin Long <lucien.xin@gmail.com>
Fixes: c9f2c1ae123a ("udp6: fix socket leak on early demux")
Fixes: 2abb7cdc0dc8 ("udp: Add support for doing checksum unnecessary conversion")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 2abb7cdc0dc8 ("udp: Add support for doing checksum
unnecessary conversion") left out the early demux path for
connected sockets. As a result IP_CMSG_CHECKSUM gives wrong
values for such socket when GRO is not enabled/available.
This change addresses the issue by moving the csum conversion to a
common helper and using such helper in both the default and the
early demux rx path.
Fixes: 2abb7cdc0dc8 ("udp: Add support for doing checksum unnecessary conversion")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or
128 unicast filter entries. (Table 7-8 MAC Address Registers from
databook) Fix dwmac1000_validate_ucast_entries() to accept values
between 1 and 32 in addition.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The Code of Conflict is not achieving its implicit goal of fostering
civility and the spirit of 'be excellent to each other'. Explicit
guidelines have demonstrated success in other projects and other areas
of the kernel.
Here is a Code of Conduct statement for the wider kernel. It is based
on the Contributor Covenant as described at www.contributor-covenant.org
From this point forward, we should abide by these rules in order to help
make the kernel community a welcoming environment to participate in.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Olof Johansson <olof@lxom.net>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sync syscall to DAX file needs to flush processor cache, but it
currently does not flush to existing DAX files. This is because
'ext4_da_aops' is set to address_space_operations of existing DAX
files, instead of 'ext4_dax_aops', since S_DAX flag is set after
ext4_set_aops() in the open path.
New file
--------
lookup_open
ext4_create
__ext4_new_inode
ext4_set_inode_flags // Set S_DAX flag
ext4_set_aops // Set aops to ext4_dax_aops
Existing file
-------------
lookup_open
ext4_lookup
ext4_iget
ext4_set_aops // Set aops to ext4_da_aops
ext4_set_inode_flags // Set S_DAX flag
Change ext4_iget() to initialize i_flags before ext4_set_aops().
Fixes: 5f0663bb4a64 ("ext4, dax: introduce ext4_dax_aops")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Suggested-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
|
|
Ext4 mount path calls .bmap to the journal inode. This currently
works for the DAX mount case because ext4_iget() always set
'ext4_da_aops' to any regular files.
In preparation to fix ext4_iget() to set 'ext4_dax_aops' for ext4
DAX files, add ext4_bmap() to 'ext4_dax_aops', since bmap works for
DAX inodes.
Fixes: 5f0663bb4a64 ("ext4, dax: introduce ext4_dax_aops")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Suggested-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
|
|
Marking mmp bh dirty before writing it will make writeback
pick up mmp block later and submit a write, we don't want the
duplicate write as kmmpd thread should have full control of
reading and writing the mmp block.
Another reason is we will also have random I/O error on
the writeback request when blk integrity is enabled, because
kmmpd could modify the content of the mmp block(e.g. setting
new seq and time) while the mmp block is under I/O requested
by writeback.
Signed-off-by: Li Dongyang <dongyangli@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@vger.kernel.org
|
|
When in effect, add "test_dummy_encryption" to _ext4_show_options() so
that it is shown in /proc/mounts and other relevant procfs files.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingol Molnar:
"Misc fixes:
- EFI crash fix
- Xen PV fixes
- do not allow PTI on 2-level 32-bit kernels for now
- documentation fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/APM: Fix build warning when PROC_FS is not enabled
Revert "x86/mm/legacy: Populate the user page-table with user pgd's"
x86/efi: Load fixmap GDT in efi_call_phys_epilog() before setting %cr3
x86/xen: Disable CPU0 hotplug for Xen PV
x86/EISA: Don't probe EISA bus for Xen PV guests
x86/doc: Fix Documentation/x86/earlyprintk.txt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: various scheduler metrics corner case fixes, a
sched_features deadlock fix, and a topology fix for certain NUMA
systems"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix kernel-doc notation warning
sched/fair: Fix load_balance redo for !imbalance
sched/fair: Fix scale_rt_capacity() for SMT
sched/fair: Fix vruntime_normalized() for remote non-migration wakeup
sched/pelt: Fix update_blocked_averages() for RT and DL classes
sched/topology: Set correct NUMA topology type
sched/debug: Fix potential deadlock when writing to sched_features
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also breakpoint and x86 PMU driver fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
perf tools: Fix maps__find_symbol_by_name()
tools headers uapi: Update tools's copy of linux/if_link.h
tools headers uapi: Update tools's copy of linux/vhost.h
tools headers uapi: Update tools's copies of kvm headers
tools headers uapi: Update tools's copy of drm/drm.h
tools headers uapi: Update tools's copy of asm-generic/unistd.h
tools headers uapi: Update tools's copy of linux/perf_event.h
perf/core: Force USER_DS when recording user stack data
perf/UAPI: Clearly mark __PERF_SAMPLE_CALLCHAIN_EARLY as internal use
perf/x86/intel: Add support/quirk for the MISPREDICT bit on Knights Landing CPUs
perf annotate: Fix parsing aarch64 branch instructions after objdump update
perf probe powerpc: Ignore SyS symbols irrespective of endianness
perf event-parse: Use fixed size string for comms
perf util: Fix bad memory access in trace info.
perf tools: Streamline bpf examples and headers installation
perf evsel: Fix potential null pointer dereference in perf_evsel__new_idx()
perf arm64: Fix include path for asm-generic/unistd.h
perf/hw_breakpoint: Simplify breakpoint enable in perf_event_modify_breakpoint
perf/hw_breakpoint: Enable breakpoint in modify_user_hw_breakpoint
perf/hw_breakpoint: Remove superfluous bp->attr.disabled = 0
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Misc fixes: liblockdep fixes and ww_mutex fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/ww_mutex: Fix spelling mistake "cylic" -> "cyclic"
locking/lockdep: Delete unnecessary #include
tools/lib/lockdep: Add dummy task_struct state member
tools/lib/lockdep: Add empty nmi.h
tools/lib/lockdep: Update Sasha Levin email to MSFT
jump_label: Fix typo in warning message
locking/mutex: Fix mutex debug call and ww_mutex documentation
|
|
Fix build warning in apm_32.c when CONFIG_PROC_FS is not enabled:
../arch/x86/kernel/apm_32.c:1643:12: warning: 'proc_apm_show' defined but not used [-Wunused-function]
static int proc_apm_show(struct seq_file *m, void *v)
Fixes: 3f3942aca6da ("proc: introduce proc_create_single{,_data}")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jiri Kosina <jikos@kernel.org>
Link: https://lkml.kernel.org/r/be39ac12-44c2-4715-247f-4dcc3c525b8b@infradead.org
|
|
The batadv interfaces are virtual interfaces which just tunnel the traffic
over other ethernet compatible interfaces. It doesn't need serialization
during the tx phase and is using RCU for most of its internal
datastructures. Since it doesn't have actual queues which could be locked
independently, the throughput gets significantly reduced by the extra lock
in the core net code.
8 parallel TCP connections forwarded by an IPQ4019 based hardware over
5GHz could reach:
* without LLTX: 349 Mibit/s
* with LLTX: 563 Mibit/s
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
B.A.T.M.A.N. IV requires the number of rebroadcast from a neighboring
originator. These statistics are gathered per interface which transmitted
the OGM (and then received it again). Since an originator is not interface
specific, a resizable array was used in each originator.
This resizable array had an entry for each interface and had to be resizes
(for all OGMs) when the number of active interface was modified. This could
cause problems when a large number of interface is added and not enough
continuous memory is available to allocate the array.
There is already a per interface originator structure "batadv_orig_ifinfo"
which can be used to store this information.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
A private debug logging infrastructure is currently provided via
$debug_fs/batman_adv/*/log when CONFIG_BATMAN_ADV_DEBUG is enabled. This is
not well integrated in the rest of the tracing infrastructure of the
kernel.
Other components (like mac80211 or ath10k) allow to gather the debug
messages using generic trace events which are better integrated. This makes
it possible to interact with them using the existing userspace tools.
The tracepoint batadv:batadv_dbg will now be available when
CONFIG_BATMAN_ADV_DEBUG and CONFIG_BATMAN_ADV_TRACING is activated. The log
level mask is still used for filtering as usual.
A full system trace for offline parsing can be created (and read) using:
$ batctl ll all
$ trace-cmd record -e batadv:batadv_dbg
$ trace-cmd report
The same can also be done without recording to a file
$ batctl ll all
$ trace-cmd stream -e batadv:batadv_dbg
The trace infrastructure is especially helpful when tracing processes:
$ batctl ll all
$ ./tools/perf/perf trace --event "batadv:*" batctl p 10.204.32.1
0.000 batadv:batadv_dbg:batman_adv bat0 Parsing outgoing ARP REQUEST
0.045 batadv:batadv_dbg:batman_adv bat0 ARP MSG = [src: a2:64:14:53:f8:22-10.204.32.185 dst: 00:00:00:00:00:00-10.204.32.1]
0.067 batadv:batadv_dbg:batman_adv bat0 Entry updated: 10.204.32.185 a2:64:14:53:f8:22 (vid: -1)
0.099 batadv:batadv_dbg:batman_adv bat0 batadv_dat_select_candidates(): IP=10.204.32.1 hash(IP)=48902
0.757 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 0: selected fe:2c:91:68:29:2b addr=48977 dist=65460
1.178 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 1: selected fe:81:ab:c5:e3:03 addr=49181 dist=65256
1.809 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 2: selected 66:25:a7:48:37:fb addr=49328 dist=65109
1.828 batadv:batadv_dbg:batman_adv bat0 DHT_SEND for 10.204.32.1
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Pull cifs fixes from Steve French:
"Fixes for four CIFS/SMB3 potential pointer overflow issues, one minor
build fix, and a build warning cleanup"
* tag '4.19-rc3-smb3-cifs' of git://git.samba.org/sfrench/cifs-2.6:
cifs: read overflow in is_valid_oplock_break()
cifs: integer overflow in in SMB2_ioctl()
CIFS: fix wrapping bugs in num_entries()
cifs: prevent integer overflow in nxt_dir_entry()
fs/cifs: require sha512
fs/cifs: suppress a string overflow warning
|
|
Pull NFS client bugfixes from Anna Schumaker:
"These are a handful of fixes for problems that Trond found. Patch #1
and #3 have the same name, a second issue was found after applying the
first patch.
Stable bugfixes:
- v4.17+: Fix tracepoint Oops in initiate_file_draining()
- v4.11+: Fix an infinite loop on I/O
Other fixes:
- Return errors if a waiting layoutget is killed
- Don't open code clearing of delegation state"
* tag 'nfs-for-4.19-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Don't open code clearing of delegation state
NFSv4.1 fix infinite loop on I/O.
NFSv4: Fix a tracepoint Oops in initiate_file_draining()
pNFS: Ensure we return the error if someone kills a waiting layoutget
NFSv4: Fix a tracepoint Oops in initiate_file_draining()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"This fixes an issue with the build system caused by a change that
modifies CC_FLAGS_FTRACE. The issue is that it breaks the dependencies
and causes "make targz-pkg" to rebuild the entire world"
* tag 'trace-v4.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/Makefile: Fix handling redefinition of CC_FLAGS_FTRACE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fix from Rob Herring:
"One regression for a 20 year old PowerMac:
- Fix a regression on systems having a DT without any phandles which
happens on a PowerMac G3"
* tag 'devicetree-fixes-for-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: fix phandle cache creation for DTs with no phandles
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains some minor cleanups and fixes:
- a new knob for controlling scrubbing of pages returned by the Xen
balloon driver to the Xen hypervisor to address a boot performance
issue seen in large guests booted pre-ballooned
- a fix of a regression in the gntdev driver which made it impossible
to use fully virtualized guests (HVM guests) with a 4.19 based dom0
- a fix in Xen cpu hotplug functionality which could be triggered by
wrong admin commands (setting number of active vcpus to 0)
One further note: the patches have all been under test for several
days in another branch. This branch has been rebased in order to avoid
merge conflicts"
* tag 'for-linus-4.19c-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gntdev: fix up blockable calls to mn_invl_range_start
xen: fix GCC warning and remove duplicate EVTCHN_ROW/EVTCHN_COL usage
xen: avoid crash in disable_hotplug_cpu
xen/balloon: add runtime control for scrubbing ballooned out pages
xen/manage: don't complain about an empty value in control/sysrq node
|
|
Pull Xtensa fixes and cleanups from Max Filippov:
- don't allocate memory in platform_setup as the memory allocator is
not initialized at that point yet;
- remove unnecessary ifeq KBUILD_SRC from arch/xtensa/Makefile;
- enable SG chaining in arch/xtensa/Kconfig.
* tag 'xtensa-20180914' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: enable SG chaining in Kconfig
xtensa: remove unnecessary KBUILD_SRC ifeq conditional
xtensa: ISS: don't allocate memory in platform_setup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The trickle of arm64 fixes continues to come in.
Nothing that's the end of the world, but we've got a fix for PCI IO
port accesses, an accidental naked "asm goto" and a fix to the
vmcoreinfo PT_NOTE merged this time around which we'd like to get
sorted before it becomes ABI.
- Fix ioport_map() mapping the wrong physical address for some I/O
BARs
- Remove direct use of "asm goto", since some compilers don't like
that
- Ensure kimage_voffset is always present in vmcoreinfo PT_NOTE"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
asm-generic: io: Fix ioport_map() for !CONFIG_GENERIC_IOMAP && CONFIG_INDIRECT_PIO
arm64: kernel: arch_crash_save_vmcoreinfo() should depend on CONFIG_CRASH_CORE
arm64: jump_label.h: use asm_volatile_goto macro instead of "asm goto"
|
|
Add a helper for the case when the nfs4 open state has been set to use
a delegation stateid, and we want to revert to using the open stateid.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
The previous fix broke recovery of delegated stateids because it assumes
that if we did not mark the delegation as suspect, then the delegation has
effectively been revoked, and so it removes that delegation irrespectively
of whether or not it is valid and still in use. While this is "mostly
harmless" for ordinary I/O, we've seen pNFS fail with LAYOUTGET spinning
in an infinite loop while complaining that we're using an invalid stateid
(in this case the all-zero stateid).
What we rather want to do here is ensure that the delegation is always
correctly marked as needing testing when that is the case. So we want
to close the loophole offered by nfs4_schedule_stateid_recovery(),
which marks the state as needing to be reclaimed, but not the
delegation that may be backing it.
Fixes: 0e3d3e5df07dc ("NFSv4.1 fix infinite loop on IO BAD_STATEID error")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Now that the value of 'ino' can be NULL or an ERR_PTR(), we need to
change the test in the tracepoint.
Fixes: ce5624f7e6675 ("NFSv4: Return NFS4ERR_DELAY when a layout fails...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
If someone interrupts a wait on one or more outstanding layoutgets in
pnfs_update_layout() then return the ERESTARTSYS/EINTR error.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Now that the value of 'ino' can be NULL or an ERR_PTR(), we need to
change the test in the tracepoint.
Fixes: ce5624f7e6675 ("NFSv4: Return NFS4ERR_DELAY when a layout fails...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fix from Vinod Koul:
"Fix the mic_x100_dma driver to use devm_kzalloc for driver memory, so
that it is freed properly when it unregisters from dmaengine using
managed API"
* tag 'dmaengine-fix-4.19-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: mic_x100_dma: use devm_kzalloc to fix an issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for -rc4.
The usual suspects of gadget, xhci, and dwc2/3 are in here, along with
some reverts of reported problem changes, and a number of build
documentation warning fixes. Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
Revert "cdc-acm: implement put_char() and flush_chars()"
usb: Change usb_of_get_companion_dev() place to usb/common
usb: xhci: fix interrupt transfer error happened on MTK platforms
usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()
usb: misc: uss720: Fix two sleep-in-atomic-context bugs
usb: host: u132-hcd: Fix a sleep-in-atomic-context bug in u132_get_frame()
usb: Avoid use-after-free by flushing endpoints early in usb_set_interface()
linux/mod_devicetable.h: fix kernel-doc missing notation for typec_device_id
usb/typec: fix kernel-doc notation warning for typec_match_altmode
usb: Don't die twice if PCI xhci host is not responding in resume
usb: mtu3: fix error of xhci port id when enable U3 dual role
usb: uas: add support for more quirk flags
USB: Add quirk to support DJI CineSSD
usb: typec: fix kernel-doc parameter warning
usb/dwc3/gadget: fix kernel-doc parameter warning
USB: yurex: Check for truncation in yurex_read()
USB: yurex: Fix buffer over-read in yurex_write()
usb: host: xhci-plat: Iterate over parent nodes for finding quirks
xhci: Fix use after free for URB cancellation on a reallocated endpoint
USB: add quirk for WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are three small HVC tty driver fixes to resolve a reported
regression from 4.19-rc1.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: hvc: hvc_write() fix break condition
tty: hvc: hvc_poll() fix read loop batching
tty: hvc: hvc_poll() fix read loop hang
|
|
- In CXGB4_DCB_STATE_FW_INCOMPLETE state check if the dcb
version is changed and update the dcb supported version.
- Also, fill the priority code point value for priority
based flow control.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matteo reported the following splat, testing the datapath of TC 'sample':
BUG: KASAN: null-ptr-deref in tcf_sample_act+0xc4/0x310
Read of size 8 at addr 0000000000000000 by task nc/433
CPU: 0 PID: 433 Comm: nc Not tainted 4.19.0-rc3-kvm #17
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS ?-20180531_142017-buildhw-08.phx2.fedoraproject.org-1.fc28 04/01/2014
Call Trace:
kasan_report.cold.6+0x6c/0x2fa
tcf_sample_act+0xc4/0x310
? dev_hard_start_xmit+0x117/0x180
tcf_action_exec+0xa3/0x160
tcf_classify+0xdd/0x1d0
htb_enqueue+0x18e/0x6b0
? deref_stack_reg+0x7a/0xb0
? htb_delete+0x4b0/0x4b0
? unwind_next_frame+0x819/0x8f0
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
__dev_queue_xmit+0x722/0xca0
? unwind_get_return_address_ptr+0x50/0x50
? netdev_pick_tx+0xe0/0xe0
? save_stack+0x8c/0xb0
? kasan_kmalloc+0xbe/0xd0
? __kmalloc_track_caller+0xe4/0x1c0
? __kmalloc_reserve.isra.45+0x24/0x70
? __alloc_skb+0xdd/0x2e0
? sk_stream_alloc_skb+0x91/0x3b0
? tcp_sendmsg_locked+0x71b/0x15a0
? tcp_sendmsg+0x22/0x40
? __sys_sendto+0x1b0/0x250
? __x64_sys_sendto+0x6f/0x80
? do_syscall_64+0x5d/0x150
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
? __sys_sendto+0x1b0/0x250
? __x64_sys_sendto+0x6f/0x80
? do_syscall_64+0x5d/0x150
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
ip_finish_output2+0x495/0x590
? ip_copy_metadata+0x2e0/0x2e0
? skb_gso_validate_network_len+0x6f/0x110
? ip_finish_output+0x174/0x280
__tcp_transmit_skb+0xb17/0x12b0
? __tcp_select_window+0x380/0x380
tcp_write_xmit+0x913/0x1de0
? __sk_mem_schedule+0x50/0x80
tcp_sendmsg_locked+0x49d/0x15a0
? tcp_rcv_established+0x8da/0xa30
? tcp_set_state+0x220/0x220
? clear_user+0x1f/0x50
? iov_iter_zero+0x1ae/0x590
? __fget_light+0xa0/0xe0
tcp_sendmsg+0x22/0x40
__sys_sendto+0x1b0/0x250
? __ia32_sys_getpeername+0x40/0x40
? _copy_to_user+0x58/0x70
? poll_select_copy_remaining+0x176/0x200
? __pollwait+0x1c0/0x1c0
? ktime_get_ts64+0x11f/0x140
? kern_select+0x108/0x150
? core_sys_select+0x360/0x360
? vfs_read+0x127/0x150
? kernel_write+0x90/0x90
__x64_sys_sendto+0x6f/0x80
do_syscall_64+0x5d/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fefef2b129d
Code: ff ff ff ff eb b6 0f 1f 80 00 00 00 00 48 8d 05 51 37 0c 00 41 89 ca 8b 00 85 c0 75 20 45 31 c9 45 31 c0 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 6b f3 c3 66 0f 1f 84 00 00 00 00 00 41 56 41
RSP: 002b:00007fff2f5350c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 000056118d60c120 RCX: 00007fefef2b129d
RDX: 0000000000002000 RSI: 000056118d629320 RDI: 0000000000000003
RBP: 000056118d530370 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000002000
R13: 000056118d5c2a10 R14: 000056118d5c2a10 R15: 000056118d5303b8
tcf_sample_act() tried to update its per-cpu stats, but tcf_sample_init()
forgot to allocate them, because tcf_idr_create() was called with a wrong
value of 'cpustats'. Setting it to true proved to fix the reported crash.
Reported-by: Matteo Croce <mcroce@redhat.com>
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Fixes: 5c5670fae430 ("net/sched: Introduce sample tc action")
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are a few small staging and iio driver fixes for -rc4.
Nothing major, just a few small bugfixes for some reported issues, and
a MAINTAINERS file update for the fbtft drivers.
We also re-enable the building of the erofs filesystem as the XArray
patches that were causing it to break never got merged in the -rc1
cycle, so there's no reason it can't be turned back on for now. The
problem that was previously there is now being handled in the Xarray
tree at the moment, so it will not hit us again in the future.
All of these patches have been in linux-next with no reported issues"
* tag 'staging-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vboxvideo: Change address of scanout buffer on page-flip
staging: vboxvideo: Fix IRQs no longer working
staging: gasket: TODO: re-implement using UIO
staging/fbtft: Update TODO and mailing lists
staging: erofs: rename superblock flags (MS_xyz -> SB_xyz)
iio: imu: st_lsm6dsx: take into account ts samples in wm configuration
Revert "iio: temperature: maxim_thermocouple: add MAX31856 part"
Revert "staging: erofs: disable compiling temporarile"
MAINTAINERS: Switch a maintainer for drivers/staging/gasket
staging: wilc1000: revert "fix TODO to compile spi and sdio components in single module"
|
|
print per rx-queue packet errors in sge_qinfo
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not put host-endian 0 or 1 into big endian feild.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a small handful of char/misc driver fixes for 4.19-rc4.
All of them are simple, resolving reported problems in a few drivers.
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
firmware: Fix security issue with request_firmware_into_buf()
vmbus: don't return values for uninitalized channels
fpga: dfl: fme: fix return value check in in pr_mgmt_init()
misc: hmc6352: fix potential Spectre v1
Tools: hv: Fix a bug in the key delete code
misc: ibmvsm: Fix wrong assignment of return code
android: binder: fix the race mmap and alloc_new_buf_locked
mei: bus: need to unlink client before freeing
mei: bus: fix hw module get/put balance
mei: fix use-after-free in mei_cl_write
mei: ignore not found client in the enumeration
|
|
pcpu_lstats is defined in several files, so unify them as one
and move to header file
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1f40a46cf47c12d93a5ad9dccd82bd36ff8f956a.
It turned out that this patch is not sufficient to enable PTI on 32 bit
systems with legacy 2-level page-tables. In this paging mode the huge-page
PTEs are in the top-level page-table directory, where also the mirroring to
the user-space page-table happens. So every huge PTE exits twice, in the
kernel and in the user page-table.
That means that accessed/dirty bits need to be fetched from two PTEs in
this mode to be safe, but this is not trivial to implement because it needs
changes to generic code just for the sake of enabling PTI with 32-bit
legacy paging. As all systems that need PTI should support PAE anyway,
remove support for PTI when 32-bit legacy paging is used.
Fixes: 7757d607c6b3 ('x86/pti: Allow CONFIG_PAGE_TABLE_ISOLATION for x86_32')
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Cc: linux-mm@kvack.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Link: https://lkml.kernel.org/r/1536922754-31379-1-git-send-email-joro@8bytes.org
|
|
Patch series "mmu_notifiers follow ups".
Tetsuo has noticed some fallouts from 93065ac753e4 ("mm, oom: distinguish
blockable mode for mmu notifiers"). One of them has been fixed and picked
up by AMD/DRM maintainer [1]. XEN issue is fixed by patch 1. I have also
clarified expectations about blockable semantic of invalidate_range_end.
Finally the last patch removes MMU_INVALIDATE_DOES_NOT_BLOCK which is no
longer used nor needed.
[1] http://lkml.kernel.org/r/20180824135257.GU29735@dhcp22.suse.cz
This patch (of 3):
93065ac753e4 ("mm, oom: distinguish blockable mode for mmu notifiers") has
introduced blockable parameter to all mmu_notifiers and the notifier has
to back off when called in !blockable case and it could block down the
road.
The above commit implemented that for mn_invl_range_start but both
in_range checks are done unconditionally regardless of the blockable mode
and as such they would fail all the time for regular calls. Fix this by
checking blockable parameter as well.
Once we are there we can remove the stale TODO. The lock has to be
sleepable because we wait for completion down in gnttab_unmap_refs_sync.
Link: http://lkml.kernel.org/r/20180827112623.8992-2-mhocko@kernel.org
Fixes: 93065ac753e4 ("mm, oom: distinguish blockable mode for mmu notifiers")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
This patch removes duplicate macro useage in events_base.c.
It also fixes gcc warning:
variable ‘col’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
The command 'xl vcpu-set 0 0', issued in dom0, will crash dom0:
BUG: unable to handle kernel NULL pointer dereference at 00000000000002d8
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 7 PID: 65 Comm: xenwatch Not tainted 4.19.0-rc2-1.ga9462db-default #1 openSUSE Tumbleweed (unreleased)
Hardware name: Intel Corporation S5520UR/S5520UR, BIOS S5500.86B.01.00.0050.050620101605 05/06/2010
RIP: e030:device_offline+0x9/0xb0
Code: 77 24 00 e9 ce fe ff ff 48 8b 13 e9 68 ff ff ff 48 8b 13 e9 29 ff ff ff 48 8b 13 e9 ea fe ff ff 90 66 66 66 66 90 41 54 55 53 <f6> 87 d8 02 00 00 01 0f 85 88 00 00 00 48 c7 c2 20 09 60 81 31 f6
RSP: e02b:ffffc90040f27e80 EFLAGS: 00010203
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff8801f3800000 RSI: ffffc90040f27e70 RDI: 0000000000000000
RBP: 0000000000000000 R08: ffffffff820e47b3 R09: 0000000000000000
R10: 0000000000007ff0 R11: 0000000000000000 R12: ffffffff822e6d30
R13: dead000000000200 R14: dead000000000100 R15: ffffffff8158b4e0
FS: 00007ffa595158c0(0000) GS:ffff8801f39c0000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000002d8 CR3: 00000001d9602000 CR4: 0000000000002660
Call Trace:
handle_vcpu_hotplug_event+0xb5/0xc0
xenwatch_thread+0x80/0x140
? wait_woken+0x80/0x80
kthread+0x112/0x130
? kthread_create_worker_on_cpu+0x40/0x40
ret_from_fork+0x3a/0x50
This happens because handle_vcpu_hotplug_event is called twice. In the
first iteration cpu_present is still true, in the second iteration
cpu_present is false which causes get_cpu_device to return NULL.
In case of cpu#0, cpu_online is apparently always true.
Fix this crash by checking if the cpu can be hotplugged, which is false
for a cpu that was just removed.
Also check if the cpu was actually offlined by device_remove, otherwise
leave the cpu_present state as it is.
Rearrange to code to do all work with device_hotplug_lock held.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Scrubbing pages on initial balloon down can take some time, especially
in nested virtualization case (nested EPT is slow). When HVM/PVH guest is
started with memory= significantly lower than maxmem=, all the extra
pages will be scrubbed before returning to Xen. But since most of them
weren't used at all at that point, Xen needs to populate them first
(from populate-on-demand pool). In nested virt case (Xen inside KVM)
this slows down the guest boot by 15-30s with just 1.5GB needed to be
returned to Xen.
Add runtime parameter to enable/disable it, to allow initially disabling
scrubbing, then enable it back during boot (for example in initramfs).
Such usage relies on assumption that a) most pages ballooned out during
initial boot weren't used at all, and b) even if they were, very few
secrets are in the guest at that time (before any serious userspace
kicks in).
Convert CONFIG_XEN_SCRUB_PAGES to CONFIG_XEN_SCRUB_PAGES_DEFAULT (also
enabled by default), controlling default value for the new runtime
switch.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
When guest receives a sysrq request from the host it acknowledges it by
writing '\0' to control/sysrq xenstore node. This, however, make xenstore
watch fire again but xenbus_scanf() fails to parse empty value with "%c"
format string:
sysrq: SysRq : Emergency Sync
Emergency Sync complete
xen:manage: Error -34 reading sysrq code in control/sysrq
Ignore -ERANGE the same way we already ignore -ENOENT, empty value in
control/sysrq is totally legal.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
